JZAQ BT30 User manual

JZAQ
User Manual
HELMET BLUETOOTH HEADPHONE

Thank you for choosing our products. To make sure you can
use the product correctly, please read the following directions
carefully before using, then follow it strictly.
SAFETY WARNING:
● The device is only IPX7 life waterproof, please do not put it
under water or using it in the rain.
● Please do not expose the product into acid, alkaline or hard
and pointy objects when using.
● If the product is wet or damp by rain, or moldy, please
place it in a low-temperature dry place, do not Insolate or
put into the oven and other high-temperature places.
● Please do not throw the device and Its battery into the fire.
● Please do not disassemble, repair or refit the product.
● Please do not pull or throw the product.
SPECIFICATIONS:
1 .Bluetooth Version; V5.0+EDR
2.Frequency Response: 2.402GHz-2.480GHz
3.Bluetooth Distance: 20M
4.MIC distance: siM
S.Lithium Battery: 3.7V/900mA
6.Charging Time: 2-3 hours
7.Standby Time: 500 hours
8.Working Time: 55-60 hours
9.Bluetooth Matching Name: bt30
FEATURES:
1.Bluetooth V5.0+EDR version, available for most of devices
with Bluetooth function.
2.Automatically answer in-coming call, and support to refuse
the call by hit any buttons 2 seconds when phone call in.
3.Support display battery on phone
4.Support 1-driven-2 mode

Fig 1
V
m
A
Volume *■/
Nexl song
USB chArgo
Wl-B
Volume /
Previous song
Fig 2

FUNCTION & OPERATION
Charging
Plug micro USB port into earphone, then connect it to the
computer or adapter by the USB cable, at the time, the LED
light wiil turn red, when the LED light is turn on blue light, it
means the speaker is fully charged, please pull out the cable.
Notice
1) First time using this product, please fully charge the
product for 2 to 3 hours.
2) When it is charging, helmet headphone can not play
music or answer the phone call.
J
Power on
Press the >ll ’button 3 seconds, the device is on once
“Blue" LED slowly flash.
Power off
Press the >|| ’button 3 seconds again, the device is off
while the LED is off.
Paring
Press and hold the key “ HI ” for 5 seconds until the LED
light flash blue and red, please try to search the Bluetooth
name of “ bt30 ” on your phone, set-in the
password of ’OOOO’if it is the first time to pair the device,
when you hear ’connected’ means paired successful and
the Blue LED slowly flashing. >
Automatically Re-pair
Your device can be automatically re-pair promptly once both
device not cancel the paring, and hear “connected’ means
the device is paired.

Play/Pause
Press “ ^11 "button to pause the song, press It again to
continue the song
Previous Song/Next Song
Press"-" button one time for previous song
Press"+ "button one time for next song
Volume Increase/Decrease
Decrease the volume: Press and hold the button to
decrease the volume and when the volume is reduced
to a minimum make “Dong" sound.
Increase the volume: Press and hold the button to
increase the volume and when the volume is increased
to a maximum make “Dong* sound.
Phone Call Answer
(Automatic)
I.Call answer: When the phone comes in, you can dial the
number and answer it automatically, or just press the
“ ^n"
button to answer it.
2.Refuse call answer: Press the “ HI ’ button for 2-3
seconds.
Support “Siri” voice assistant
Short press ” ■■ "tWO times to start the smart voice assistant
to make calls
Low Power Warning
The device sound "Dong Dong"waming voice while working, ^

It means the power is low, please charge it.
Power Save Mode
The device will be off automatically after 5 minutes no
working device pairing it.
1 Drive-2 Mode
The phone support two simultaneous pairing:
First pair the phone 1 with the Helmet Headset and then
disconnect the phone 1's Bluetooth;
After pairing the Helmet Headset with mobile phone 2, open
the Bluetooth of mobile phone 1 and click connect "BT30" to
connect two mobile phones at the same time;
Now phone 1 and phone 2 paired with Helmet Headset
together and support to answer any call from two phones
(Note: phonel and phone 2 can not answer calls at the same time.)
Installing Step
Step1
Take out the Helmet Headphone from the color box. stick
the “Magic Tape “on both earphones.
Step2
Tear off the 3M tape paper of the earphones, and stick it into
the helmet ear position of both sides, before stick it, please
align the position well,see Fig3.
Accessories
1* Helmet Headphone
2* Detachable Clip
r USB Cable
1’ User Manual
6

It can automatically answer a call after the number
Is announced
Treble and bass Settings:
Please press and hold ‘ + ’’ button or" -" button to increase or
decrease the volume (If you think it is not easy to control the
volume on the Bluetooth headset, you also can adjust the
volume on your phone to achieve what you want.)
Switch between Chinese and English:
The Helmet Bluetooth Headset language is English by default.
If you want to switch languages please turn on the headset first
without connect to Bluetooth, and then press the power on button
twice to switch the language.
Tips:
If you have any questions during the use of our product, please feel
free to contact us via seller center. If technical
support is required,
please contact: www.jzaq.com email:[email protected] .
1

Manufacluror:
ShenZhon ma sha^^g Lai wart nelworV l«chr>ology Co.,Ltd
Brand JZAQ
Wobsite: wwwj/aq com
Adresse: Uriit 2, Gaili Hengiai Scier>co arid TechrxMogy Park. No. 26, Liaokeng Avenue.
Shiyan, Bao'an Diatncl. Shen^non, Guangdong, Cnma