Küppersbusch KD 674.1GE Quick setup guide

GB
F
NL
I
E
BEDIENUNGSANWEISUNG
mit Montageanweisungen
Instructions for use and installation instructions
Instructions d’ utilisation et a is de montage
Gebruiksaanwijzing en montagehandleiding
Istruzioni di uso e di montaggio
Instrucciones de uso y de montaje
KD 674.1GE
KD 974.1GE

3
Contenuti - Contenents
1 - GENERALITÀ ..................................................................................... 6
2 - COMPONENTI ................................................................................... 6
3 - AVVERTENZE PER LA SICUREZZA ....................................................... 6
4 - INSTALLAZIONE ................................................................................ 7
4.1 - Scelta del tipo di installazione ........................................................................ 7
4.2 - Installazione del corpo cappa C ...................................................................... 8
4.3 - Installazione del camino A ........................................................................... 10
4.4 - Connessione aspirante o filtrante ................................................................. 12
4.5 - Connessione elettrica e controllo funzionale ................................................... 12
1 - AVVERTENZE PER LA SICUREZZA ..................................................... 13
2 - USO ........................................................................................ 13
3 - MANUTENZIONE ............................................................................. 13
3.1 - Filtri antigrasso metallici ............................................................................. 14
3.2 - Filtro al carbone attivo ................................................................................ 14
3.3 - Illuminazione ............................................................................................. 15
3.4 - Pulizia ...................................................................................................... 15
1 - GENERAL DATA ............................................................................... 16
2 - COMPONENTS ................................................................................ 16
3 - SAFETY WARNINGS ........................................................................ 16
4 - INSTALLATION ................................................................................ 17
4.1 - Selecting the type of installation ................................................................... 17
4.2 - Installation of the hood canopy C .................................................................. 18
4.3 - Installation of the chimney A ........................................................................ 20
4.4 - Ducting or recirculation fitting...................................................................... 22
4.5 - Connection to power supply and checking of good working order....................... 22
1 - SAFETY WARNINGS ........................................................................ 23
2 - OPERATION .................................................................................... 23
3 - MAINTENANCE ............................................................................... 23
3.1 - Metal grease filters ................................................................................... 24
3.2 - Activated charcoal filter .............................................................................. 24
3.3 - Light ........................................................................................................ 25
3.4 - Cleaning ................................................................................................... 25

Part 1 - INSTALLATION INSTRUCTIONS
1 - GENERAL DATA
This hood has been designed to be wall-mounted abo e a cooking hob with one side
resting against a wall. It works either by suction (external outlet) or filter (internal
recycling). Because of the complexity and weight of the hood, its installation
should be carried out by qualified staff, taking care to respect all local
regulations on air discharge. The manufacturer cannot be found liable for any
damage due to improper installation.
2 - COMPONENTS
The cooker hood is made up of the following components (fig. 1):
2.1 - No. 1 canopy C complete
with controls and worktop
illumination;
2.2 - No. 1 telescopic chimney
stack A complete with
ducting fan unit;
2.3 - No. 1 flange Ø 120 or Ø
150 F;
2.4 - No. 1 enting grill G;
2.5 - No. 1 ducting spigot R;
2.6 - No. 1 support rod B;
2.7 - No. 1 fixing kit containing:
No. 1 wall bracket S to fix
the canopy hood;
No. 1 co er D, screws, rawl
plugs and documentation.
3 - SAFETY WARNINGS
3.1 - When used in the extraction mode the cooker hood ducting must not be connected to
a flue which is used for exhausting fumes from appliances supplied with energy other
than electric such as a central heating flue or water heating flue.
3.2 - Before connecting to the mains supply ensure that the mains voltage corresponds with
the voltage on the rating plate inside the hood.
3.3 - Connect the cooker hood to the mains via a double pole switch which has 3 mm metal
clearance between the contacts.
3.4 - The appliance must be earthed.
3.5 - When installed, the hood must be positioned at least 65 cm above a cooking appliance.
3.6 - Never do flambé cooking under this cooker hood.
3.7 - Never leave frying pans unattended during use as overheated fats and oils may catch
fire.
A08_01
R
G
F
S
B
A
C
1
1

17
Part 1 - INSTALLATION INSTRUCTIONS
3.8 - Before carring out any kind of maintenance or cleaning, disconnect the hood from the
mains supply.
3.9 - If the room where the cooker hood is to be used contains a fuel burning appliance such
as a central heating boiler then this must be of the room sealed or balanced flue type.
If other types of flue or appliance are fitted ensure that there is an adequate supply of
air into the room. When the cooker hood is used in conjunction with other appliances
supplied with energy other than electric, the negative pressure in the room must not
exceed 0,04 mbar to prevent fumes being drawn back into the room by the cooker
hood.
4 - INSTALLATION
The ersatility of the ducting fan unit on this hood enables it to be installed in one of
four different ways:
1 - Air outlet directed upwards (ducting or recirculation fitting).
2 - Air outlet directed towards the wall (ducting fitting only).
3 - Air outlet directed to the right or left (ducting fitting only). For correct installation of
the hood, please proceed in the following stages:
4.1 - Selection of the type of installation
4.2 - Installation of the hood canopy C
4.3 - Installation of the chimney A
4.4 - Ducting or recirculation fitting
4.5 - Electrical connection and testing
4.1 - Selecting the type of installation
1 - Air discharge towards the top
In this case the hood can be used
either in filter mode (fig. 2a) or in
suction mode (fig. 2b).
2 - Air discharge towards the wall
(fig. 3)
In this case the hood can only be
used in suction mode.
3 - Side air discharge, Lh or Rh (fig.
4a-b).
In this case the hood can only be
used in suction mode.
G
2a 2b
S07_02
2
2
4
4
3
3

Part 1 - INSTALLATION INSTRUCTIONS
4.2 - Installation of the hood canopy C
1 - Drilling the wall
a) Mark on the wall the centres of holes 1 for fixing of the hood canopy C. The centre of
hole 2 for fixing the chimney, (fig. 5a) air outlet directed upwards or towards the wall,
(fig. 5b-c) air outlet to the right or left hand side, must be marked at a distance X
from the line between holes 1, obtained by measuring the extension Z of the chimney
required for installation, plus 11 mm X=Z+18-7. Using a Ø8 mm drill bit, drill the
points marked in this way.
b) When installed with the air outlet directed towards the wall
(fig. 5a), it will be necessary to drill an air ducting opening,
measuring Ø120 or 150 mm, according to the diameter of
the flange F pro ided.
2 - Fitting the fixing elements
a) Insert the rawl plugs pro ided into holes 1 and 2.
b) Fit the eye bolts O (fig. 6).
c) Fix the wall bracket S in hole 2 using the screw V pro ided
(fig. 7).
ø120
ø150
100 100 ø8
7
Z
X
40
18
650
105 105
A08_05
2
1 1
2
11
2
11
5a
5a 5b 5b 5c 5c
6
6
7
7

19
Part 1 - INSTALLATION INSTRUCTIONS
3 - Fitting the hood canopy C to the wall
a) Remo e the metal grease filters and the
acti ated charcoal filter, if there is any (see
the paragraph on Maintenance).
b) Fit the support rod B using the two screws
K (3,5x9,5) pro ided (fig. 8).
c) Hook the hood canopy C to the eye bolts
O fixed in holes 1 (fig. 9).
d) Adjust the support rod B so that it pushes
against the wall (fig. 10).
e) Adjusting position (fig. 11). There are two adjustable hooks at the rear of the hood,
which can be used to adjust its position as follows:
- Turn the screws L until the position of screws N coincides with the lower access
holes.
- Turn the screws N to adjust the ertical and horizontal position of the hood.
- Lock the screws L to fasten the hood against the wall.
- Insert the plugs T pro ided in the holes gi ing access to screws N.
8
8
9
9
11
11
B
A08_10
10
10

Part 1 - INSTALLATION INSTRUCTIONS
4.3 - Installation of the chimney A
No matter which type of installation is being used, any wooden shel es in the area
where the hood is to be fitted must first be remo ed, drilled and later replaced.
1 - Drilling the shelves:
a) Using the cardboard template pro ided,
and taking hole “B” as a point of
reference, drill the shel es along the
central axis to allow the passage of the
chimney. The chimney must be inserted
into the shel es before it is fixed to the
hood canopy C (fig. 12).
b) When installing the ducting ersion with
the air outlet directed upwards, if the
ducting fan unit is positioned below the
line of shel es it will be necessary to
drill a suitable hole in the top shelf only,
to allow the air ducting pipe to pass
through (fig. 13).
2 - Direction and position of the ducting
fan unit
a) The hood is normally supplied with the
air towards the wall installed with the to
the right or left be necessary to change of the ducting fan
proceeding as follows:
- Unscrew the screws
- Turn the ducting the right or
left;
- Replace the screws U.
b)The ducting fan unit air
outlets must be arranged
according to the type of
installation to be carried out.
· Air outlet directed upwards (fig. 2a-b).
- Remo e the plastic plug from the upper part of the enting
grill and replace it on the rear part (fig. 15).
· Air outlet directed towards the wall (fig. 3).
- Remo e the plastic frame from the air outlet (fig. 16).
A08_12
12
12
13
13
14
14
15
15
16
16

21
Part 1 - INSTALLATION INSTRUCTIONS
- Remo e the plug from the upper part of
the ducting fan unit (fig. 17), as it is not
possible to insert the flange F with the
plug in place.
- Fit the flange F Ø120 or 150 mm (fig.
18), replace the plug.
· Air outlet directed to the right or left
hand side (fig. 4a-b).
- Remo e the four screws fastening the
plastic frame, as shown in fig. 16.
- Fit the ducting spigot R (fig. 19) and replace
the four screws remo ed as abo e.
3 - Fixing the chimney
a) Loosen the screws M fixing the two parts
of the chimney and pull the inner section I (fig. 20)
almost all the way out. Remo e the protecti e film P.
b) Rest the lower section of the chimney in its housing on
the top of the hood canopy. Lower the ducting fan unit
until it reaches the wall bracket S and fix it using the
screw H pro ided (fig. 21). Fit the co er D (pro ided)
on the wall bracket S (fig. 22).
c) Insert gasket G1 (found in the accessory bag) on the
base of chimney stack A, so
that it adheres perfectly to the
shape of chimney stack A. Then
fix chimney stack A to the hood
unit C using four of the screws
pro ided E (fig. 23).
d) Insert the transparent seal Q
(pro ided), so as to eliminate
any play between the two parts
of the chimney (fig. 24). Lock
the screws M.
e) Remo e the support rod B.
17
17
18
18
20
20
19
19
E
E
E
E
A08_TL
A
G1
C
21
21
22
22
23
23
24
24

Part 1 - INSTALLATION INSTRUCTIONS
4.4 - Ducting or recirculation fitting
1 - Ducting fitting.
This is possible for all forms of installation:
a) Connect the air outlet to the external ducting system.
b) Remo e the acti ated charcoal filter (if there is one) inside the
hood canopy (see Maintenance).
2 - Recirculation fitting
This is only possible with the air outlet directed upwards. Fit the
enting grille G onto the air outlet (Fig. 25). The acti ated charcoal
filter should be fitted inside the hood canopy after connection to
the power supply.
4.5 - Connection to power supply and checking
of good working order
1 - It is absolutely necessary to follow
the warnings 3.2, 3.3 and 3.4 of
paragraph 3, concerning safety
measures.
2 - Loosen the two locking screws and
remo e the metal co er (fig.26).
Connect the hood connection to the
engine connection (fig.27a).
Correctly place the connectors
under the co er and tighten the two
locking screws (fig. 27b).
3 - Once electrical connection has
been carried out, check that lights,
engine and change of speed work
4 - Fit the antigrease filters (paragraph
4.2) and the acti ated carbon filter
(only for filter mode) (see
Maintenance).
25
25
A08_26
26
26
27b
A08_27
27a
27
27

23
Part 2 - USE AND MAINTENANCE INSTRUCTIONS
1 - SAFETY WARNINGS
It is most important that all the warnings shown in paragraph 3 of the Installation
Instructions are strictly observed. Moreover, pay special attention to the following
warnings during the use and maintenance of the cooker hood:
1.1 - The grease filters and charcoal filters should be cleaned or replaced as recommended
by the manufacturer or more frequently if the hood is used consistently (over 4 hours
per day).
1.2 - When using a gas hob in connection with the cooker hood never leave the burners of
the hob uncovered while the hood is in use or when the pans have been removed.
Switch off the gas before removing the pan, or for just short periods and never leave
the hob unattended.
1.3 - Always ensure that the flame is kept at the correct intensity to prevent the flame from
licking round from the bottom of the pan; this will save energy and will avoid a dangerous
concentration of heat.
1.4 - Always ensure that the appliance is used in accordance with the manufacturer’s
instructions for the removal of contaminated air and odours during cooking.
2 - OPERATION
Control Panel (fig. 28)
The layout of the control panel is as follows:
Key = Turns the lighting system on and off
Key = Turns the motor on and off
Key = Decreases the working speed
Key = Increases the working speed
Key = Intensi e speed with
timed stoppage. Suitable to
deal with maximum apour
emission, this turns off
automatically 10 minutes after
starting operation. It can be disabled by pressing the key .
3 - MAINTENANCE
Constant maintenance guarantees proper operation and long-term reliability.
Particular attention should be paid to the metal grease filters and, for recirculation
hoods only, to the acti ated charcoal filters. The appliance is equipped with a system
that indicates automatically when it is time to carry out maintenance operations.
28
28

24
Part 2 - USE AND MAINTENANCE INSTRUCTIONS
3.1 - Metal grease filters
1 - Cleaning
These filters must be washed when LED 0/1 Motor starts to flash, or at
the most once e ery 2 months, using a normal household detergent;
their compact size also enables them to be washed in a dishwasher.
2 - Removing the filters
Remo e one filter at a time, supporting
it from below and pulling back the
stainless steel handle (fig.29 ). Replace,
making sure that the handle is still facing
towards the outside.
3 - Enabling the alarm signal
The hood is already set up to trigger an
alarm indicating saturation of the metal
grease filters, so this function does not
need to be enabled.
4 - Resetting the alarm signal
To turn the alarm signal off, proceed as follows:
- Turn off the lights and the suction motor;
- Press the Speed + button for at least 3 seconds, until the LEDs flash in confirmation.
In any case the saturated filters alarm will only come into operation when the suction
motor is turned on.
WARNING: always comply with the maintenance and replacement times
indicated, in order to avoid a possible risk of fire when the filters are saturated
with grease.
3.2 - Acti ated charcoal filter
1 - Operation
The acti ated charcoal filter is only fitted in recirculation type hoods. It
will retain odours until it becomes saturated. It cannot be washed or
regenerated, and must be replaced when the Intensive Speed LED starts
to flash, or at least once e ery 4 months of use. Attention: in recirculation
type hoods the 0/1 Motor LED may
start to flash as well as the Speed +
LED. This indicates that as well as
replacing the acti ated charcoal
filter, it is also necessary to perform
maintenance operations on the
metal grease filters (see paragraph
3.1).
29
29
30
30

25
Part 2 - USE AND MAINTENANCE INSTRUCTIONS
2 - Replacing
Remo e the grease filters and take out the acti ated charcoal filter from its housing,
turning the lugs pro ided (fig. 30). Insert the new acti ated charcoal filter and replace
the metal grease filters.
3 - Enabling the alarm signal
In recirculation type hoods the saturated filters alarm must be enabled as indicated
below:
- Turn off the lights and the suction motor;
- Press and hold the Speed + button for at least 10 seconds, until the LEDs start to
flash. Note the number of flashes:
- 2 flashes of the LED Acti ated charcoal filter saturation alarm ENABLED.
- 1 flash of the LED Acti ated charcoal filter saturation alarm DISABLED;
4 - Resetting the alarm signal
To turn the alarm signal off, proceed as follows:
- Press the Speed + button for at least 3 seconds, until the LEDs flash in confirmation.
In any case the saturated filters alarm will only come into operation when the suction
motor is turned on.
WARNING: always comply with the maintenance and replacement times
indicated, in order to avoid a possible risk of fire when the filters are saturated
with grease.
3.3 - Light
1 - It consists of 2 20 W-halogen spotlights.
2 - Replacement (fig. 31)
Remo e the two screws that lock the metal ring,
take the spotlight out of its holder by pulling
slightly. When replacing, make sure that both pins
are well inserted in the holder seat.
3.4 - Cleaning
Normal cleaning operation of the hood:
- Do not use any wet cloth or sponge or water-jet.
- Do not use diluents or alcohol, as they could make the painted surfaces opaque.
- Do not use abrasi e products, especially on stainless steel surfaces.
We recommend the use of a damp cloth and any neutral liquid detergent.
S07_28
31
31