Kärcher KM 130/300 R Bp User manual

QUICKSTART
5.964-141.0 03/14
Warning
Theseareonlybriefinstructions!Pleasereadtheoperatinginstructionsaccompanying the appliance prior to using
or maintaining the appliance.
The non-compliance with the operating and safety instructions may lead to damage of the appliance and to risks
for the operator and other persons.
Start up
1ABCA Sit on the driver seat.
B Turn the ignition key to position "I".
Note
The indicator of the battery capacity will show the
actual charge status after approx. 10 seconds.
C Check charge of battery; charge it
if necessary.
2ABCA Check the wheels for tied up belts.
B Check roller brush.
C Check side brush.
3ABCA Pull seat adjustment lever outwards.
B Move seat, release lever and
lock in place.
Check that the seat is properly locked in
position by attempting to move it backwards
and forwards.
C Adjust the seat back.
KM 130/300 R BP

QUICKSTART
5.964-141.0 03/14
Operation
1A
D
B
E
CStarting the machine
A Sit on the driver's seat.
Do not press the accelerator pedal.
B Lock parking brake.
C Bring the direction selector switch into
the middle position.
D Insert the ignition key into the ignition switch.
Turn the ignition key to position "I".
The appliance is now ready for operation.
E Turn the ignition key to position "II".
The appliance can now be driven.
2A
D
G
B
E
H
C
F
Drive the machine
A Set programme switch to step 1 (driving).
B Press brake pedal and keep it depressed.
C Release parking brake.
Drive forward
D Set the travel direction switch to "forward".
E Press accelerator pedal down slowly.
Reverse drive
Danger
Risk of injury! While reversing, ensure that there
is nobody in the way, ask them to move if some-
body is around.
F Set the travel direction switch to "backwards".
G Press accelerator pedal down slowly.
Brakes
H Release the accelerator pedal, the machine
brakes automatically and stops.
Note
The braking effect can be supported by pressing
the brake pedal.

QUICKSTART
5.964-141.0 03/14
3A B Sweeping mode
Sweeping with sweep roller
A Set programme switch to stage 2.
Roller brush is lowered.
Sweeping using roller brush and side
brushes
B Set programme switch to step 3.
Side brushes and roller brush are lowered.
4ASweeping damp or wet floors
A Switch off the blower.
5ACleaning the dust filter
A Press the switch of the dust filter cleaning
system.
6AOperation with beacon lamp
A Switch on the beacon lamp.
Operation

QUICKSTART
5.964-141.0 03/14
7A
CD
BEmptying waste container
Danger
Risk of injury! When emptying the waste
container, care should be taken to ensure that no
persons or animals are within its swivelling range.
Danger
Danger of crushing. Never reach into the rod
assembly for the drainage mechanism. Stay
away from the area under the raised container.
Danger
Danger of tipping. Place the machine on an even
surface during emptying.
A Raise waste container.
Slowly drive up to the collecting container
.
Lock parking brake.
B Open the flap of the waste container.
C Close the flap of the waste container.
Release parking brake.
Drive away the collection container slowly.
D Lower the waste container up to the
end-position.
Finish operation
1Emptying waste container
See "Operation", item 7.
2ABCTurn off the appliance
A Set programme switch to stage 1 (driving).
The side brushes and roller brush are raised.
B Press brake pedal and keep it depressed.
Lock parking brake.
C Turn ignition key to "0" and remove it.
Operation

QUICKSTART
5.964-141.0 03/14
Maintenance and care
daily weekly Kärcher Customer Service
1AA Check function of all control
elements.
B Inspect appliance for
damage.
2A B A Check the hydraulic oil level.
B Check brake fluid status.
Danger
Risk of injury! Always insert the safety
rod when the waste container
is raised.
3A B A Check dust filter and clean filter
box, if required.
B Clean the machine with a damp
cloth which has been soaked in
mild detergent.
Note
Do not use aggressive cleaning
agents.
4A Clean the hydraulic oil cooler.
B Check hydraulic unit.
C Check the sealing strips for wear,
replace as necessary.
D Check the container lid and
lubricate it.
5See inspection checklist
5.950-648.0!