K m l ser 60 controller
Using your mini controller with your K m l ser 60
M ke sure the dipswitches on the re r on the l ser re set s follows
Dip switch 1 nd 10 in the on position
Mode:
There are 4 mode unctions, 0 = sound to light mode 1 = automatic mode 2 = mini controller mode with sound activation 3
= mini controller mode with manual movement
Light:
This button operates the black out unction, pressing this button will turn the laser light output o , pressing once again will
turn the black out mode o and the laser light will be on
Pge:
There are 5 steps on this button 0-4 each page runs in conjunction with the pattern select buttons; each page activates a
di erent selection o patterns
PAUSE:
This unction has just one step and when pressed once this will pause the movement o the image, when the button is
pressed again this will un reeze the image
V MOVE:
This button has one step 0-1 in the 0 position the image will be standard, in the 1 position the image will scan up and
down. NOTE. In mode 2 the scanning unction will be sound activated, in mode 3 the scanning unction will be automatic
H MOVE:
This button has one step 0-1 in the 0 position the image will be standard, in the 1 position the image will scan le t to right.
NOTE. In mode 2 the scanning unction will be sound activated, in mode 3 the scanning unction will be automatic
H CONVERSION:
This button has one step 0-1 in the 0 position the image will be standard, in the 1 position the image will rotate.
NOTE. In mode 2 the scanning unction will be sound activated, in mode 3 the scanning unction will be automatic
RESET:
This button resets the unit back to its original star up position and de aults to mode 0 sound to light mode
SPEED UP:
This button has 12 steps 0 - A + 11 in the 0 position the image is in the standard static position, pressing this button will adjust
the speed o the image depending on what program is selected ie. Setting an image to rotate, this will increase the rota-
tion speed o the image 11 being the astest speed
SPEED DOWN:
This button has 11 steps, and will reduce the speed o the image set by the controller, this button only operates as a speed
reduction button i the unit has already had the speed increased using the speed up button. i the speed is set in the 0
position this button will not unction
To obtain individual patterns using the mini controller,
Press the mode button until 3 is displayed in the led display
At this point 3 horizontal lines in will display
1. Switch on the laser
2. press the mode button to display 3 in the led screen
3. press the pattern select buttons 0 - 7 to select desired pattern
P ge 0
P ttern 0 3x horizontal lines
P ttern 1 tunnel
P ttern 2 2x witches hat
P ttern 3 2x square
P ttern 4 lge tunnel
P ttern 5 horizontal lat beam
P ttern 6 vertical lat beam
P ttern 7 2 x horizontal lat beam
P ge 1
P ttern 0 2 x vertical lat beam
P ttern 1 cross
P ttern 2 small vertical lat beam
Pttern 3 small horizontal lat beam
P ttern 4 small vertical lat beam
P ttern 5 small horizontal lat beam
P ttern 6 diagonal lat beam
P ttern 7 diagonal lat beam
P ge 2
P ttern 0 vertical rectangle
P ttern 1 lge square
P ttern 2 lge tunnel
P ttern 3 lge triangle
P ttern 4 lge M
P ttern 5 lge lat beam
P ttern 6 lge lat beam
P ttern 7 lge lat beam
P ge 3
P ttern 0 lge lat beam
P ttern 1 lge lat beam
P ttern 2 triangle
P ttern 3 lge S
P ttern 4 square
P ttern 5 square
P ttern 6 square
P ttern 7 small square
Kam C-60 la er controller manual 1.qxp:Layout 1 24/4/08 18:17 Page 3
