Kamstrup MULTICAL 602 Parts list manual

KamstrupA/S∙Industrivej28,Stilling∙DK‐8660Skanderborg∙T:+4589931000∙[e-mail] ∙kamstrup.com

99
TechnicalDescription
MULTICAL®602

MULTICAL®602
2KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 3
List of contents
1General description ..........................................................................................................6
2Technical Data ..................................................................................................................7
2.1Approved meter data ............................................................................................................................7
2.2Electrical data.......................................................................................................................................8
2.3Mechanical data.................................................................................................................................10
2.4Materials ............................................................................................................................................10
2.5Accuracy.............................................................................................................................................10
3Type overview.................................................................................................................11
3.1Type and programming overview.........................................................................................................11
3.2Type number combination ..................................................................................................................12
3.3PROG, A-B-CCC-CCC ............................................................................................................................14
3.4Display coding....................................................................................................................................21
3.5>EE< Configuration of MULTITARIFF......................................................................................................23
3.6>FF< Input A (VA) - pulse divider, >GG< Input B (VB) - pulse divider.........................................................25
3.7Configuration of pulse outputs in the top module................................................................................26
3.8>MN< Configuration of leak limits.........................................................................................................26
3.9>T< Configuration of encryption level....................................................................................................26
3.10Data for configuration.........................................................................................................................27
4Dimensional sketches.....................................................................................................28
5Installation .....................................................................................................................29
5.1Inlet pipe and outlet pipe placing........................................................................................................29
5.2EMC conditions...................................................................................................................................30
5.3Climatic conditions.............................................................................................................................30
5.4Electric installations ...........................................................................................................................30
6Calculator functions........................................................................................................31
6.1Energy calculation ..............................................................................................................................31
6.2Application types................................................................................................................................32
6.3Calculator with two flow sensors.........................................................................................................37
6.4Combined heat/cooling metering........................................................................................................38
6.5Flow measurement, V1 and V2............................................................................................................39
6.6Power measurement, V1.....................................................................................................................40
6.7Min. and max. flow and power, V1 ......................................................................................................41
6.8Temperature measurement.................................................................................................................42
6.9Display functions................................................................................................................................44
6.10Real Time Clock (RTC)..........................................................................................................................47
6.11Info codes ..........................................................................................................................................48
6.12Tariff functions ...................................................................................................................................51
6.13Data loggers .......................................................................................................................................56

MULTICAL®602
4KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
6.14Leak surveillance ............................................................................................................................... 58
6.15Reset functions.................................................................................................................................. 61
6.16SMS Commands ................................................................................................................................ 61
6.17Set-up via the front keys..................................................................................................................... 63
6.18Reset via the front keys...................................................................................................................... 65
6.19Preset the pulse value for V1 and V2 .................................................................................................. 66
7Flow sensor connection .................................................................................................. 67
7.1 Volume inputs V1 and V2......................................................................................................................... 67
7.2Flow sensor with active 24 V pulse output ......................................................................................... 69
7.3Pulse inputs VA and VB...................................................................................................................... 72
8Temperature sensors...................................................................................................... 74
8.1Sensor types...................................................................................................................................... 75
8.2Cable influence and compensation .................................................................................................... 76
8.3Pocket sensors .................................................................................................................................. 78
8.4Pt500 short direct sensor set ............................................................................................................. 79
9Voltage supply ............................................................................................................... 80
9.1Integral D-cell lithium battery ............................................................................................................. 80
9.2Battery lifetimes................................................................................................................................. 81
9.3High Power supply module 230 VAC................................................................................................... 82
9.4High Power supply module 24 VAC..................................................................................................... 82
9.5Supply module 230 VAC..................................................................................................................... 83
9.6Supply module 24 VAC....................................................................................................................... 83
9.7Exchanging the supply unit ................................................................................................................ 85
9.8Mains supply cables .......................................................................................................................... 85
9.9Back-up of data during power down ................................................................................................... 86
9.10Danish regulations for connection of mains operated meters.............................................................. 86
10Plug-in modules .......................................................................................................... 87
10.1Top modules...................................................................................................................................... 87
10.2Base modules.................................................................................................................................... 93
10.3Retrofitting modules ........................................................................................................................ 103
11Data communication.................................................................................................. 104
11.1MULTICAL602 data protocol .......................................................................................................... 104
11.2MULTICAL®602 communication paths ............................................................................................. 106
11.3Optical eye....................................................................................................................................... 106
12Calibration and verification ....................................................................................... 107
12.1High-resolution energy reading ........................................................................................................ 107
12.2High-resolution volume for test ........................................................................................................ 108
12.3Verification adapter ......................................................................................................................... 109
12.4True energy calculation .................................................................................................................... 110

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 5

13METERTOOL and LogView for MULTICAL602 ............................................................111
13.1Introduction......................................................................................................................................111
13.1How to use METERTOOL HCW for MULTICAL® 602...............................................................................112
13.2Verification with METERTOOL MULTICAL602....................................................................................118
13.3LogView HCW....................................................................................................................................121
14Approvals ..................................................................................................................123
14.1CE marking .......................................................................................................................................123
14.2Measuring instrument directive.........................................................................................................123
15Trouble-shooting .......................................................................................................124
16Disposal ....................................................................................................................125
17Documents ................................................................................................................126
18Appendix A - MULTICAL602 vs. previous meters......................................................127
19Appendix B - MULTICAL602 vs. MULTICAL6L2.......................................................127
20Appendix C - MULTICAL6M2, a calculator for mixed fluids.......................................128

MULTICAL®602
6KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
1General description
MULTICAL®602 is a thermal energy meter with many applications. In addition to being a precise and reliable heat
meter for battery or mains operation, MULTICAL®602 is also used for:
Cooling measurement in water-based systems
Bifunctional heat/cooling measurements in separate registers
Leak surveillance of hot and cold-water installations
Power and flow limiter with valve control
Data logger
Data communication
Energy measurement in open systems
In designing the MULTICAL®602 we have attached great importance to flexibility via programmable functions and
plug-in modules (see chapter 10) in both the calculator top as well as in the base unit to ensure optimal use in a
large number of applications. In addition, the construction ensures that already installed MULTICAL®602 meters
can be updated via the PC program METERTOOL.
This technical description is prepared to give utility managers, meter electricians, consulting engineers and
distributors the possibility of utilizing all functions available in the MULTICAL®602. Furthermore, the description is
made for laboratories for the testing and verification process.

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 7
2Technical Data
2.1 Approved meter data
Standard EN 1434:2007, prEN 1434:2009 and OIML R75:2002
EU directives Measuring Instrument Directive, Low Voltage Directive,
Electromagnetic Compatibity Directive
Heat meter approval D
K
-0200-MI004-020
The stated minimum temperatures
apply to the type approval only.
The meter has no cut-off for low
temperature and thus measures as low
temperatures as
0.01C and 0.01 K.
Temperature range : 2C…180C
Differential range : 3 K…170 K
Cooling meter
Temperature range : 2C…50C
Differential range : 3 K…40 K
Accuracy EC(0.5 +  min/) %
Temperature sensors -Type 602-A Pt100 – EN 60 751, 2-wire connection
-Type 602-B and 602-D Pt500 – EN 60 751, 4-wire connection
-Type 602-C Pt500 – EN 60 751, 2-wire connection
Compatible flow sensor types -ULTRAFLOW
-Electronic meters with an active 24 V pulse output
-Mechanical meters with an electronic pick-up unit
-Mechanical meters with a Reed switch
Flow sensor sizes kWhqp 0.6 m3/h…15 m3/h
MWhqp 0.6 m3/h…1500 m3/h
GJqp 0.6 m3/h…3000 m3/h
EN 1434 designation Environmental class A and C
MID designation Mechanical environment: Class M1
Electromagnetic environment: Class E1 and E2
5…55 °C, non condensing, closed location (indoor installation)

MULTICAL®602
8KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
2.2 Electrical data
Calculator data
Typical accuracy Calculator: EC(0.15 + 2/) %
Sensor set: ET

(0.4 + 4/) %
Display LCD – 7 (8) digits with a digit height of 7.6 mm
Resolution 9999.999 – 99999.99 –
999999.9 –
9999999
Energy units MWh – kWh – GJ –
Gcal
Data logger (EEPROM) Standard: 1392 hours, 460 days, 36 months, 15 years, 50 info codes
Option: Data loggers with programmable interval
Clock/calendar Clock, calendar, compensation for leap years, target date, Real time clock
with battery back-up
Data communication KMP protocol with CRC16 used for optical communication
and for top and
base modules
Power in temperature
sensors 10

W RMS
Supply voltage 3.6 VDC ± 0.1 VDC
Battery 3.65 VDC, D-cell lithium
Stand-by current 15

A excluding flow sensor
Replacement interval
- Mounted on the wall
- Mounted on the flow sensor
12+1 years @ tBAT30 °C
10 years @ tBAT40 °C
The replacement interval is reduced when using data modules, frequent data
communication and high ambient temperature. See chapter 9.2.
Mains supply
230 VAC +15/-30 %, 50/60 Hz
24 VAC ±50 %, 50/60 Hz, see paragraph 9.6.1 re choice of transformer
Insulation voltage 4 kV
Power supply 1W
Bac
k
-up supply Integral super-cap eliminates operational disturbances due to short-term
power cuts (Power supply modules type 602-0000-7 and type 602-0000-8
only)
EMC data Meets prEN 1434-4:2009 class C (MID class E2)
Temperature measurement
T1 T2 T3 T4
602-A
2-W Pt100
Measuring range
0.00…185.00C 0.00…185.00C 0.00…185.00C N/A
Preset range 0.01…180.00C 0.01…180.00C 0.01…180.00C 0.01…180.00C
602-B/D
4-W Pt500
Measuring range
0.00…185.00C 0.00…185.00C N/A
N/A
Preset range 0.01…180.00C 0.01…180.00C N/A
0.01…180.00C
602-C
2-W Pt500
Measuring range
0.00…185.00C 0.00…185.00C 0.00…185.00C N/A
Preset range 0.01…180.00C 0.01…180.00C 0.01…180.00C 0.01…180.00C
Max. cable lengths Pt100, 2-wire Pt500, 2-wire
Pt500, 4-wire
Max. ø6mm cable 2 x 0.25 mm2: 2.5 m
2 x 0.50 mm2: 5 m
2 x 1.00 mm2:10 m
2 x 0.25 mm2: 10 m
2 x 0.50 mm2: 20 m
4 x 0.25 mm2: 100 m
-

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 9
Flow
measuring V1 and V2 ULTRAFLOW
V1: 9-10-11 and V2: 9-69-11
Reed switches
V1: 10-11 and V2: 69-11
FET switches
V1: 10-11 and V2: 69-11
24 V active
p
ulses
V1: 10B-11B and V2: 69B-79B
CCC-code 1xx and 2xx 0xx
9xx
2xx and
9xx
EN 1434
p
ulse class IC IB
IB
(IA)
Pulse in
p
ut 680 kpull-up for 3.6 V 680 k

pull-up for 3.6 V 680 k

pull-up for 3.6 V 12 mA at 24 V
Pulse ON

0.4 V in 0.5 ms

0.4 V in 100 ms

4 V i 3 ms 4 V in 3 ms
Pulse OFF 2.5 V in 10 ms 2.5 V in 100 ms 12 V i 10 ms 12 V in 10 ms
Pulse frequency

128 Hz

1 Hz

4 Hz 128 Hz
Integration frequency

1 Hz

1 Hz

2 Hz 1 Hz
Electrical isolation No No
No
2 kV
Max. cable length 10 m 25 m
25 m
100 m
Pulse inputs
without
bounce damping:
Pulse inputs VA and VB
VA: 65-66 and VB: 67-68
Water meter connection
FF(VA) and GG(VB) = 71…90
Electricity meter connection
FF(VA) and GG(VB) = 50…70
Pulse in
p
ut 680 kpull-up for 3.6 V 680 k

pull-up for 3.6 V
Pulse ON

0.4 V in 30 ms

0.4 V in 30 ms
Pulse OFF 2.5 V in 100 ms 2.5 V in 100 ms
Pulse frequency

1 Hz

3 Hz
Electrical isolation No No
Max. cable length 25 m 25 m
Requirements to external
contact Leakage current at function open

1

A
Pulse inputs
with
bounce damping:
Pulse inputs VA and VB
VA: 65-66 and VB: 67-68
Water meter connection
FF(VA) and GG(VB) = 01…40
Pulse in
p
ut 680 kpull-up for 3.6 V
Pulse ON

0.4 V i 200 ms.
Pulse OFF 2.5 V i 500 ms.
Pulse frequency

1 Hz
Electrical isolation None
Max. Cable length 25 m
Requirements to external
contact Leakage current at function open

1

A
Pulse outputs CE and CV
- via top module
602-0A/0C
67-0B
Ty
p
e O
p
en collector (OB)
O
p
to FET
External voltage 5…30 VDC 5…48 VDC/AC
Current 1…10 mA 1…50 mA
Residual voltage UCE ≈1 V at 10 mA RON ≤40

Electrical isolation 2 kV 2 kV
Max. cable length 25 m 25 m
Pulse length O
p
tional 32 ms or 100 ms

MULTICAL®602
10KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
2.3 Mechanical data
Environmental class Meets EN 1434 class A and C
Ambient temperature 5…55
°C non condensing, closed location (indoor installation)
Protection class IP54
Storage temperature -20…60 °C (drained meter)
Weight 0.4 kg excluding sensors and flow
sensor
Connection cables ø3.5…6 mm
Supply cable ø5…10 mm
2.4 Materials
Top cover PC
Base unit ABS
with TPE packings (thermoplastic elastomer)
Print bo
x
ABS
Wall brackets
DIN rail bracket
PC + 30 % glass
PC + 20 % glass
2.5 Accuracy
Figure 1. MULTICAL®602 typical accuracy compared with EN 1434.

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 11
3Type overview
MULTICAL
®
602 can be ordered in a countless number of combinations as required by the customer. First the
required hardware is selected in the type overview. Then “Prog”, “Config” and “Data” are selected to suit the
application in question.
The meter is delivered completely configured and ready for use from the factory but it can also be
retrofitted/reconfigured after installation.
Please note that the items marked ”Totalprog” can only be changed when the verification seal is broken. This
requires that the change must be made at an accredited meter laboratory.
New functions and modules for MULTICAL
®
602 are constantly being developed. Please contact Kamstrup A/S, if
the described variants do not meet your requirements.
3.1 Type and programming overview
PROG (Total prog.)
A-B-CCC-CCC
- Inlet pipe/Outlet pipe
- Energy unit
- Inlet meter code
CONFIG (Partial prog.)
DDD-EE-FF-GG-M-N-T
- Display
- Tariff
- Pulse inputs
- Leak sensibility
- Pulse outputs
- AMR Encryption level
DATA (Partial prog.)
- Customer no.
- Target date
- Tariff limits
- Average peak time max./min.
- Date/time
Type number (Total prog.)
602-X-X-XX-X-XX-X-XXX
Selection of Pt100/Pt500
calculator, modules, supply,
sensor set, flow sensor and
language on label

MULTICAL®602
12KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
3.2 Type number combination
MULTICAL602 Type 602-






Sensor connection
Pt100 2-wire (T1-T2) A
Pt500 4-wire (T1-T2) B
Pt500 2-wire (T1-T2-T3) C
Pt500 4-wire (T1-T2) w/24 V pulse inputs D
Top module
No module 0
Energy calculation + hourly data logger 2) 2
PQ or t-limiter + hourly data logger 3
Data output + hourly data logger 5
M-Bus 7
Volume + hourly data logger 2) 9
2 pulse outputs for CE and CV + hourly data logger + scheduler A
RTC + 2 pulse outputs for CE and CV + prog. data logger B
2 Pulse outputs CE and CV C
Base module
No module 00
Data + pulse inputs 10
M-Bus + pulse inputs 1) 20
Radio Router + pulse inputs 21
Prog. data logger + RTC + 4…20 mA inputs + pulse inputs 22
0/4…20 mA outputs 23
LonWorks + pulse inputs 24
Radio + pulse inputs (internal antenna) 434 or 444 MHz 25
Radio + pulse inputs (external antenna connection) 434 or 444 MHz
26
M-Bus module with alternative registers + pulse inputs 27
M-Bus module with medium data package + pulse inputs 28
M-Bus module with MC-III data package + pulse inputs 29
Wireless M-Bus, Mode C1 + pulse inputs (Ind. Key) 30
Wireless M-Bus, Mode T1 OMS 15 min. (Ind. Key) 31
Wireless M-Bus, Mode C1 Alt. reg. + pulse inputs 35
Wireless M-Bus, Mode T1 OMS 16 s (ind. Key) 36
Wireless M-Bus, Mode C1 Fixed Network (ind. Key) 38
Wireless M-Bus, Mode C1 Fixed Network (ind. Key), PDO data 39
ZigBee 2.4 GHz int.ant. + pulse inputs 60
Metasys N2 (RS485) + pulse inputs 62
SIOX module (Auto detect Baud rate) 64
BACnet MS/TP + pulse inputs 66
Modbus RTU + pulse inputs 67
GSM/GPRS (GSM6H) 80
3G GSM/GPRS module (GSM8H) 81
High Power RadioRouter + pulse inputs 84
Supply
No supply 0
Battery, D-cell 2
230 VAC high power isolated SMPS 3
24 VAC high power isolated SMPS 4
230 VAC isolated linear supply 7
24 VAC isolated linear supply 8
Pt500 sensor set
No sensor set 00
Pocket sensor set w/1.5 m cable 0A
Pocket sensor set w/3.0 m cable 0B
Pocket sensor set w/5 m cable 0C
Pocket sensor set w/10 m cable 0D
Short direct sensor set w/1.5 m cable 0F
Short direct sensor set w/3.0 m cable 0G
3 Pocket sensors in sets w/1.5 m cable 0L
3 Short direct sensors in sets w/1.5 m cable Q3
Flo
w
sensor
/pic
k
-up unit
Supplied w/1 pcs. ULTRAFLOW(Please specify type)
1
Supplied w/2 pcs. (identical) ULTRAFLOW(Please specify type)
2
Prepared for 1 pcs. ULTRAFLOW(Please specify type)
7
Prepared for 2 pcs. (identical) ULTRAFLOW(Please specify type)
8
Prepared for meters w/electronic pulse output K
Prepared for meters w/Reed switch output
(
Both V1 and V2) L
Prepared for meters w/24 V active pulses
M
Meter type
Heat meter, (MID module B+D) 2
Heat/cooling meter (MID modules B+D & TS+DK268) 3
Heat meter, National approvals 4
Cooling meter (TS27.02+DK268) 5
Heat/Cooling meter 6
Volume meter, hot water 7
Volume meter, cooling water 8
Energy meter 9
Country code (language on label etc.)
XX
Require
High- Power
supply
modules

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 13
Comments to the Type number survey
When placing orders please state ULTRAFLOWtype numbers separately.
1) See paragraph 10.2 for further details.
2) Requires two identical flow sensors.
3.2.1 Accessories
1606-064 D-cell battery
602-0000-4000000 24 VAC high power isolated SMPS
602-0000-3000000 230 VAC high power isolated SMPS
602-0000-8000000 24 VAC isolated linear supply
602-0000-7000000 230 VAC isolated linear supply
6699-624 Pulse transmitter/divider for 602-A and 602-C
6699-614 4-wire connection PCB with pulse inputs for 24 V active pulses (for 602-D)
6699-098 Data cable w/USB plug
6699-099 Infrared optical reading head w/USB plug
6699-144 Infrared optical reading head for Kamstrup/EVL w/USB plug
6699-102 Infrared optical reading head w/D-sub 9F
6699-106 Data cable RS 232, D-sub 9F
6699-397/-398/-399 Verification unit (used with METERTOOL)
6556-4x-xxx Temperature sensor set with connection head (2/4-wire)
67-9xxxxxx2xx External Communication Box
5915-145 DIN rail bracket
6699-724 METERTOOL for HCW
6699-725 LogView for HCW
Please contact Kamstrup A/S for questions concerning further accessories.

MULTICAL®602
14KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
3.3 PROG, A-B-CCC-CCC
The legal parameters of the meter are determined by Prog, which can only be changed when the verification seal is
broken. The change must then be made at an accreditated meter laboratory.
The A-code indicates whether the flow sensor (V1) is installed in inlet or outlet pipe. As water has a larger volume
at higher temperatures, the calculator must be adjusted for the current installation type. Wrong programming or
installation results in measuring errors. For further details on placing the flow sensor in the inlet or outlet pipe in
connection with heat and cooling meters, see paragraph 5.1.
The B-code indicates the measuring unit used for the energy register. GJ, kWh or MWh are used most frequently,
whereas Gcal is only used in some countries outside the EEA.
The CCC code indicates the calculator’s adaptation to a specific flow sensor type, i.e. the calculation speed and
display resolution are optimised to the selected flow sensor type and at the same time the type approval regulations
concerning min. resolution and max. register overflow are met. The CCC codes are divided into several tables to
give a better survey.
CCC(V1) indicates the CCC code of the flow sensor and is connected to flow sensor input V1 on terminal 9-10-11
(or 10B-11B), which in most applications is the flow sensor used for calculating energy.
CCC(V2) indicates the CCC code of an extra flow sensor, if any, to be connected to terminal 9-69-11 (or 69B-79B).
If V2 is not used, CCC(V2) = CCC(V1). In connection with leakage surveillance CCC(V2) = CCC(V1).
Prog. number A - B - CCC (V1) - CCC (V2)
Flow sensor placing:
k-factor
table
- Inlet pipe (at T1) 3
- Outlet pipe (at T2) 4
Measuring unit, energy
- GJ
2
- kWh
3
- MWh
4
- Gcal
5
Flow sensor coding
(CCC-table)
CCC CCC

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 15
3.3.1 CCC-table for MULTICAL602
The CCC tables are divided into fast pulse codes (CCC=4XX, 2XX and 1XX) for electronic meters, e.g. ULTRAFLOW®,
and slow codes for e.g. reed contacts (CCC=0XX, 9XX).
CCC= 4XX Electronic meters with fast and bounce-free pulses as well as info codes for ULTRAFLOW®X4
Max. pulse frequency: 128 Hz
Max. integration frequency: 1 Hz
CCC= 1XX, 2XX Electronic meters with fast and bounce-free pulses
Max. pulse frequency: 128 Hz
Max. integration frequency: 1 Hz
CCC= 0XX Mechanical meters delivering slow pulses with bounce (flow sensor type "L")
Max. pulse frequency: 1 Hz
Max. integration frequency: 1 Hz
CCC=9XX Electronic meters with slow and bounce free pulses
Max. pulse frequency: 1 Hz (CCC=91X), or 4 Hz (CCC=92X)
Max. integration frequency: 1 Hz
Max. integration frequency is 1 Hz for all types. The CCC codes are arranged in a way that qs+20 % (or Qmax+
20 %) does not exceed the 1 Hz in the integration frequency.
Example: CCC=107 (applies for a qp 1.5 m3/h meter) : 1 Hz in the integration frequency is obtained at
q = 3.6 m3/h.
EN 1434 makes demands on the resolution and registre size of the energy reading. MULTICAL®602 meets these
demands when connected to below flow sensor sizes:
kWhqp 0.6 m3/h…15 m3/h
MWhqp 0.6 m3/h…1500 m3/h
GJqp 0.6 m3/h…3000 m3/h
3.3.2 CCC codes for mechanical flow sensors with Reed switch
Number of decimals on the display
CCC
no.
Pre-
counter
Flow factor kWh MWh
Gcal GJ
m³
ton
m³/h l/h kW MW l/pulses Pulses/l Qmax
m³/h
Flow
sensor
010 1 921600 1 - 3 3 - 0 1 - 1 1 3,0 L
011 1 921600 - 3 2 2 2 - 0 - 10 0.1 1…30 L
012 1 921600 - 2 1 1 1 - - 2 100 0.01 10…300 L
013 1 921600 - 1 0 0 0 - - 1 1000 0.001 100…3000
L
020 4 230400 0 3 2 2 2 - 0 - 2.5 0.4 6 L
021 4 230400 - 2 1 1 1 - - 2 25 0.04 3…60 L
022 4 230400 - 1 0 0 0 - - 1 250 0.004 30…600 L
Current flow (l/h or m³/h) reading is calculated on the basis of the measured period between 2 volume pulses
(see paragraph 6.5)
When one of above CCC codes has been selected both CCC (V1) and CCC (V2) must be selected from this table.
Note: Continuous maximum water flow and permanent  >75 K may cause overflow in the daily data logger at
CCC=010-011-012-013-150-202-205. With these combinations we recommend you to use Prog. data logger type
67-0B or type 67-00-22.

MULTICAL®602
16KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
3.3.3 CCC codes for ULTRAFLOWII, type 65 54 XXX
Number of decimals on the display
CCC
no.
Pre-
counter
Flow
factor kWh MWh Gcal GJ m³
ton
l/h m³/h kW MW Pulses/l qp
m³/h
Type no. Flow
sensor
116 3000 78642 0 3 2 2 0 - 1 - 300 0.6 65 54 A8X
65 54 AAX
1-2-7-8-K
119 1000 235926 0 3 2 2 0 - 1 - 100 1.5 65 54 A6X
65 54 A7X
65 54 A1X
65 54 A2X
65 54 A3X
1-2-7-8-K
136 500 471852 0 3 2 2 0 - 1 - 50.0 2.5 65 54 A4X
65 54 ADX
1-2-7-8-K
151 5000 471852 - 2 1 1 0 - 1 - 50.0 3.5 65 54 B1X
65 54 B7X
1-2-7-8-K
137 2500 943704 - 2 1 1 0 - 1 - 25.0 6.0
6.0
10
10
65 54 B2X
65 54 B5X
65 54 BGX
65 54 BHX
1-2-7-8-K
120 1000 2359260 - 2 1 1 0 - 1 - 10.0 15
25
65 54 B4X
65 54 B8X
1-2-7-8-K
158 5000 471852 - 1 0 0 - 2 0 - 5.0 40 65 54 B9X 1-2-7-8-K
170 2500 943704 - 1 0 0 - 2 - 3 2.5 60 65 54 BAX 1-2-7-8-K
147 1000 2359260 - 1 0 0 - 2 - 3 1.0 150 65 54 BBX 1-2-7-8-K
194 400 5898150 - 1 0 0 - 2 - 3 0.4 400 65 54 BCX 1-2-7-8-K
195 250 9437040 - 1 0 0 - 2 - 3 0.25 1000 65 54 BKX 1-2-7-8-K
Current flow reading (l/h or m³/h) is calculated on the basis of volume pulses/10 s (see paragraph 6.5)
3.3.4 CCC codes for electronic flow sensors with slow and bounce free pulses (only MC602/SVM S6)
Number of decimals on the display
CCC
no.
Pre-
counter
Flow
factor kWh
MWh
Gcal GJ m³ m³/h l/h kW MW l/ Pulses Pulses/l qp
Flow
sensor
910 1 921600 1
- 3 3
-
0
1
-
1
1 0.6-1.5
K-M
911 1 921600 -
3 2 2
2
-
0
-
10
0.1 1.5-15
K-M
912 1 921600 -
2 1 1
1
-
-
2
100
0.01 15-150
K-M
913 1 921600 -
1 0 0
0
-
-
1
1000
0.001 150-1500
K-M
920 4 230400 0
3 2 2
2
-
0
-
2.5
0.4 0.6-15
K-M
921 4 230400 -
2 1 1
1
-
-
2
25
0.04 3.5-150
K-M
922 4 230400 -
1 0 0
0
-
-
1
250
0.004 40-1500
K-M
Note: CCC=9XX can only be used for MULTICAL® 602, and not for MULTICAL®601 or MULTICAL®801.

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 17
3.3.5 CCC codes for ULTRAFLOWtype 65-SRT
Number of decimals on the display
CCC
no.
Pre-
counter
Flow-
factor kWh MWh Gcal GJ m³
ton
l/h m³/h kW MW Pulses/l qp
m³/h
Type no. Flow part
116 3000 78642 0 3 2 2 0 - 1 - 300 0.6 65-X-CAAA-XXX
65-X-CAAD-XXX
1-2-7-8-K-M
119 1000 235926 0 3 2 2 0 - 1 - 100 1.5 65-X-CDAC-XXX
65-X-CDAD-XXX
65-X-CDAE-XXX
65-X-CDAF-XXX
65-X-CDAA-XXX
1-2-7-8-K-M
136 500 471852 0 3 2 2 0 - 1 - 50.0 3.0 65-X-CFAF-XXX
65-X-CFBA-XXX
1-2-7-8-K-M
151 5000 471852 - 2 1 1 0 - 1 - 50.0 3.5 65-X-CGAG-XXX
65-X-CGBB-XXX
1-2-7-8-K-M
137 2500 943704 - 2 1 1 0 - 1 - 25.0 6
6
10
10
65-X-CHAG-XXX
65-X-CHBB-XXX
65-X-C1AJ-XXX
65-X-C1BD-XXX
1-2-7-8-K-M
178 1500 1572840 - 2 1 1 0 - 1 - 15.0 10 65-X-CJAJ-XXX
65-X-CJBD-XXX
1-2-7-8-K-M
120 1000 2359260 - 2 1 1 0 - 1 - 10.0 15 65-X-CKBE-XXX
1-2-7-8-K-M
179 600 3932100 - 2 1 1 0 - 1 - 6.0 25 65-X-CLBG-XXX
1-2-7-8-K-M
120 1000 2359260 - 2 1 1 0 - 1 - 10.0 25 65-X-C2BG-XXX
1-2-7-8-K-M
158 5000 471852 - 1 0 0 - 2 0 - 5.0 40 65-X-CMBH-
XXX 1-2-7-8-K-M
170 2500 943704 - 1 0 0 - 2 - 3 2.5 60 65-X-FABL-XXX
65-X-FACL-XXX
1-2-7-8-K-M
180 1500 1572840 - 1 0 0 - 2 - 3 1.5 100 65-X-FBCL-XXX
1-2-7-8-K-M
147 1000 2359260 - 1 0 0 - 2 - 3 1.0 150 65-X-FCBN-XXX
65-X-FCCN-XXX
1-2-7-8-K-M
181 600 3932100 - 1 0 0 - 2 - 3 0.6 250 65-X-FDCN-XXX
1-2-7-8-K-M
191 400 589815 - 1 0 0 - 1 - 2 0.4 400 65-X-FEBN-XXX
65-X-FEBR-XXX
65-X-FECN-XXX
65-X-FECP-XXX
65-X-FECR-XXX
1-2-7-8-K-M
192 250 943704 - 1 0 0 - 1 - 2 0.25 600
600
1000
1000
65-X-FFCP-XXX
65-X-FFCR-XXX
65-X-F1BR-XXX
65-X-F1CR-XXX
1-2-7-8--KM
193 150 1572840 - 1 0 0 - 1 - 2 0.15 1000 65-X-FGBR-XXX
1-2-7-8-K-M
Current flow reading (l/h or m³/h) is calculated on the basis of volume pulses/10 s (see paragraph 6.5)

MULTICAL®602
18KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
3.3.6 CCC codes with high resolution for ULTRAFLOW(for cooling meters etc.)
Number of decimals on the display
CCC
no.
Pre-
counter
Flow
factor kWh MWh Gcal GJ m³
ton
l/h m³/h kW MW Pulses/l qp
m³/h
Type no. Flow sensor
184 300 78642 1 - 3 3 0 - 1 - 300 0.6 1-2-7-8-K-M
107 100 235926 1 - 3 3 0 - 1 - 100 1.5 1-2-7-8-K-M
136 500 471852 0 3 2 2 0 - 1 - 50.0 3.5 1-2-7-8-K-M
138 250 943704 0 3 2 2 0 - 1 - 25.0 6.0
10
1-2-7-8-K-M
183 150 1572840 0 3 2 2 0 - 1 - 15.0 10 1-2-7-8-K-M
185 100 2359260 0 3 2 2 0 - 1 - 10.0 15 1-2-7-8-K-M
186 500 471852 - 2 1 1 - 2 0 - 5.0 40 1-2-7-8-K-M
187 250 943704 - 2 1 1 - 2 - 3 2.5 60 1-2-7-8-K-M
188 150 1572840 - 2 1 1 - 2 - 3 1.5 100 1-2-7-8-K-M
189 100 2359260 - 2 1 1 - 2 - 3 1.0 150 1-2-7-8-K-M
191 400 589815 - 1 0 0 - 1 - 2 0.4 400 1-2-7-8-K-M
192 250 943704 - 1 0 0 - 1 - 2 0.25 600
1000
1-2-7-8-K-M
193 150 1572840 - 1 0 0 - 1 - 2 0.15 1000 1-2-7-8-K-M
Current flow reading (l/h or m³/h) is calculated on the basis of volume pulses/10 s (see paragraph 6.5)
3.3.7 CCC codes for other electronic meters with a passive output
Number of decimals on the display
CCC
no.
Pre-
counter
Flow
factor
MWh
Gcal GJ m³
ton
m³/h kW MW l/pulse Pulses/l Qmax
m³/h
Type Flow
sensor
147 1000 2359260 1 0 0 2 - 3 1 - 18...75 SC-18 K-M
148 400 5898150 1 0 0 2 - 3 2.5
- 120…300 SC-120 K-M
149 100 2359260 1 0 0 1 - 2 10 - 450…1200 SC-450 K-M
150 20 11796300 1 0 0 1 - 2 50 - 1800…3000 SC-1800 K-M
175 7500 314568 1 0 0 2 - 3 - 7.5 15…30 DF-15 K-M
176 4500 524280 1 0 0 2 - 3 - 4.5 25…50 DF-25 K-M
177 2500 943704 1 0 0 2 - 3 - 2.5 40…80 DF-40 K-M
Number of decimals on the display
CCC
no.
Pre-
counter
Flow
factor
MWh
Gcal GJ m³
ton
m³/h MW l/pulse Pulse/l Qp range
m³/h
Qs
(m³/h) Type Flow
sensor
201 100 235926 2 1 1 1 2 1 1 10…100 75 FUS380
DN50-65
K-M
202 40 589815 2 1 1 1 2 2.5 0.4 40…200 240 FUS380
DN80-100
K-M
203 400 589815 1 0 0 1 2 2.5 0.4 100…400 500 FUS380
DN125
K-M
204 100 235926 1 0 0 0 1 10 0.1 150…1200 1600 FUS380
DN150-250
K-M
205 20 1179630 1 0 0 0 1 50 0.02 500…3000 3600 FUS380
DN300-400
K-M
Current flow reading (l/h or m³/h) is calculated on the basis of volume pulses/10 pcs. (see paragraph 6.5)
3.3.8 CCC codes for other electronic meters with an active output
Flow sensor with active 24 V pulse output, see paragraph 7.2

MULTICAL®602
KamstrupA/S∙TechnicalDescription∙5512‐931_N1_GB
_
11.2016 19
3.3.9 CCC codes for vane wheel meters with an electronic pick-up unit
Number of decimals on the display
CCC
no.
Pre-
counter
Flow
factor kWh MWh Gcal GJ m³
ton
l/h m³/h
kW
MW
Pulses/l qp
m³/h
Type Flow
sensor
102 560 421296 0 3 2 2 0 - 1 - 56.0 1.5/2.5 GWF-MT3 K
103 300 786420 0 3 2 2 0 - 1 - 30.0 3.5 GWF-MT3 K
104 2520 936214 - 2 1 1 0 - 1 - 25.2 6 GWF-MT3 K
105 1230 1918098 - 2 1 1 0 - 1 - 12.3 10 GWF-MT3 K
106 1080 2184500 - 2 1 1 0 - 1 - 10.8 15 GWF-MT3 K
108 1403 168158 0 3 2 2 0 - 1 - 140.3 0.6 GWF K
109 957 246527 0 3 2 2 0 - 1 - 95.7 1.0 GWF K
110 646 365211 0 3 2 2 0 - 1 - 64.6 1.5 GWF K
111 404 583975 0 3 2 2 0 - 1 - 40.4 1.5 (2.5) HM (GWF) K
112 502 469972 0 3 2 2 0 - 1 - 50.2 1.5 – 2.5* GWF K
113 2350 1003940 - 2 1 1 0 - 1 - 23.5 3.5 - 6* GWF K
114 712 331357 - 2 1 1 0 - 1 - 7.12 10 - 15* GWF K
115 757 311659 0 3 2 2 0 - 1 - 75.7 1.0* GWF K
116 3000 78642 0 3 2 2 0 - 1 - 300.0 0.6* GWF K
117 269 877048 0 3 2 2 0 - 1 - 26.9 1.5 Brunata K
118 665 354776 0 3 2 2 0 - 1 - 66.5 1.5 Aquastar K
119 1000 235926 0 3 2 2 0 - 1 - 100.0 0.6 HM K
121 294 802469 0 3 2 2 0 - 1 - 29.4 1.5 – 2.5 K
122 1668 141442 0 3 2 2 0 - 1 - 166.8 0.6 HM K
123 864 273063 0 3 2 2 0 - 1 - 86.4 0.75 - 1* HM K
124 522 451966 0 3 2 2 0 - 1 - 52,2 2.5 (1.5*) CG (HM) K
125 607 388675 0 3 2 2 0 - 1 - 60.7 1.5 - 1*
1.5*
HM K
126 420 561729 0 3 2 2 0 - 1 - 42.0 1.0 (2.5*) CG (HM) K
127 2982 791167 - 2 1 1 0 - 1 - 29.82 2.5
3.5*
HM K
128 2424 973292 - 2 1 1 0 - 1 - 24.24 3.5* HM K
129 1854 1272524 - 2 1 1 0 - 1 - 18.54 6* HM K
130 770 3063974 - 2 1 1 0 - 1 - 7.7 10* HM K
131 700 3370371 - 2 1 1 0 - 1 - 7.0 15* HM K
132 365 645665 0 3 2 2 0 - 1 - 36.54 2.5 Wehrle K
133 604 390154 0 3 2 2 0 - 1 - 60.47 1.5 Wehrle K
134 1230 191732 0 3 2 2 0 - 1 - 123.05 0.6 Wehrle K
135 1600 1474538 - 2 1 1 0 - 1 - 16.0 10* HM K
139 256 921586 0 3 2 2 0 - 1 - 25.6 1.5 – 2.5 GWF K
140 1280 1843172 - 2 1 1 0 - 1 - 12.8 3.5 – 5.0 GWF K
141 1140 2069526 - 2 1 1 0 - 1 - 11.4 6 GWF K
142 400 589815 - 2 1 1 - 2 - 3 4 10 GWF K
143 320 737269 - 2 1 1 - 2 - 3 3.2 10 - 15 GWF K
144 1280 1843172 - 1 0 0 - 2 - 3 1.28 25 - 40 GWF K
145 640 3686344 - 1 0 0 - 2 - 3 0.64 60 GWF K
146 128 18431719 - 1 0 0 - 2 - 3 0.128 125 GWF K
152 1194 1975930 - 2 1 1 0 - 1 - 11.94 10 GWF K
153 1014 2326686 - 2 1 1 0 - 1 - 10.14 15 GWF K
156 594 397182 0 3 2 2 0 - 1 - 59.4 1.5 Metron K
157 3764 626796 - 2 1 1 0 - 1 - 37.64 2.5 Metron K
163 1224 192750 0 3 2 2 0 - 1 - 122.4 0.6 – 1.0 GWF/U2 K
164 852 280064 0 3 2 2 0 - 1 - 85.24 1.5 GWF/U2 K
165 599 393735 0 3 2 2 0 - 1 - 59.92 2.5 GWF/U2 K
168 449 5259161 - 2 1 1 0 - 1 - 4.486 15/25 HM/WS K
169 1386 1702208 - 1 0 0 - 2 0 - 1.386 40 HM/WS K
173 500 471852 - 1 0 0 - 1 - 2 0.5 80 Westland K
Current flow reading (l/h or m³/h) is calculated on the basis of volume pulses/10 s (see paragraph 6.5)
* Multiple-jet water meter

MULTICAL®602
20KamstrupA/S∙ TechnicalDescription∙5512‐931_N1_GB_11.2016
3.3.10 ULTRAFLOWX4 CCC-codes
Number of decimals on the display
CCC
no.
Pre-
counter
Flow
factor kWh MWh Gcal GJ m³
ton
l/h m³/h kW MW Pulses/l
qp
m³/h
Type Flow
sensor
416
3000
78642
0
3
2
2
0
-
1
-
300
0.6
65-X-CAAA-XXX 1-2-7-8
65-X-CAAD-XXX
65-X-CAAF-XXX
484
300
78642
1
-
3
3
0
-
1
-
300
0.6
1-2-7-8
419
1000
235926
0
3
2
2
0
-
1
-
100
1.5
65-X-CDA1-XXX 1-2-7-8
65-X-CDAA-XXX
65-X-CDAC-XXX
65-X-CDAD-XXX
65-X-CDAE-XXX
65-X-CDAF-XXX
65-X-CDBA-XXX
407
100
235926
1
-
3
3
0
-
1
-
100
1.5
1-2-7-8
498
600
393210
0
3
2
2
0
-
1
-
60
2.5
65-X-CEAF-XXX 1-2-7-8
65-X-CEBA/CECA-XXX
65-X-CEAD-XXX
451
5000
471852
-
2
1
1
0
-
1
-
50
3.5
65-X-CGAG-XXX 1-2-7-8
65-X-CGBB/CGCB-XXX
436
500
471852
0
3
2
2
0
-
1
-
50
3.5
1-2-7-8
437
2500
943704
2
1
1
0
1
25
6
65-X-CHAF-XXX 1-2-7-8
65-X-CHAG-XXX
65-X-CHAH-XXX
65-X-CHBB/CHCB-XXX
438
250
943704
0
3
2
2
0
-
1
-
25
6
1-2-7-8
478
1500
1572840
-
2
1
1
0
-
1
-
15
10
65-X-CJAJ-XXX 1-2-7-8
65-X-CJB2/CJC2-XXX
65-X-CJBD/CJCD-XXX
483
150
1572840
0
3
2
2
0
-
1
-
15
10
1-2-7-8
420
1000
2359260
-
2
1
1
0
-
1
-
10
15
65-X-CKB4/CKC4-XXX 1-2-7-8
65-X-CKBE/CKCE-XXX
485
100
2359260
0
3
2
2
0
-
1
-
10
15
1-2-7-8
479
600
3932100
-
2
1
1
0
-
1
-
6
25
65-X-CLBG/CLCG -XXX 1-2-7-8
458
5000
471852
-
1
0
0
-
2
0
-
5
40
65-X-CMBH/CMCH -XXX
1-2-7-8
65-X-CMBJ/CMCJ -XXX
486
500
471852
-
2
1
1
-
2
0
-
5
40
1-2-7-8
470
2500
943704
-
1
0
0
-
2
-
3
2.5
60
65-X-FACL-XXX 1-2-7-8
487
250
943704
-
2
1
1
-
2
-
3
2.5
60
1-2-7-8
480
1500
1572840
-
1
0
0
-
2
-
3
1.5
100
65-X-FBCL-XXX 1-2-7-8
488
150
1572840
-
2
1
1
-
2
-
3
1.5
100
1-2-7-8
447
1000
2359260
1
0
0
2
3
1
150
65-X-FCCN-XXX 1-2-7-8
489
100
2359260
2
1
1
2
3
1
150
1-2-7-8
481
600
3932100
1
0
0
2
3
0.6
250
65-X-FDCN-XXX 1-2-7-8
491
400
589815
1
0
0
1
2
0.4
400
65-X-FECN-XXX
65-X-FECP-XXX
65-X-FECR-XXX
1-2-7-8
492
250
943704
1
0
0
1
2
0.25
600
65-X-FFCP-XXX
65-X-FFCR-XXX 1-2-7-8
493
150
1572840
1
0
0
1
2
0.15
1000
65-X-FGCR-XXX 1-2-7-8
ULTRAFLOW®CCC- codes with high resolution