K&L GPS200MV User manual

CDMA GPS Mobile Terminal
Installation Manual
Model: GPS200MV
K&L Technology Co., Ltd

2
CONTENTS
1. Safety Information .……………………. 3
2. General Specifications ………………...…. 4
3. Unpacking .…………………… 5
4. Appearance ……………………… 6
5. Installation Manual …………………….. 8
6. Troubleshooting .……………………. 17

3
1. Safety Information
Product care and maintenance
• Use only Manufacturer-approved accessories; otherwise, it
could damage this unit and may be dangerous.
• Do not disassemble this product. Take it to a qualified
service technician when repair work is required.
• The product should be kept away from heat sources.
• Do not drop.
• Do not subject this product to mechanical vibration or shock.
• This product is not water-resistant. Keep it dry.
If the product is immersed in “Water” or used in a very humid
place, the parts or circuit may get damages, causing an
electric shock or failure. Not be given free service for any
defect which is caused due to water.
Qualified service
• Only qualified service personnel may install or repair your
device.

4
2. General Specifications
Model Name GPS200MV
Technology CDMA 800MHz
GPS Stand-Alone
Dimension 61(W) x 120(H) x 24(D)mm
Weight 97g (approximately with standard battery)
Operation Temp. -30°c ~ +100°c
In put Power DC
GPS Antenna Dual PIFA Type 50ΩIntenna
Li-lon 1250mAH
About 14 hours

5
3. Unpacking
Device
(Power Cable)
(Battery) Manual
Adhesive Tape Screws (Fuse)

6
4. Appearance
①Power Button
②Emergency Reset
③Screw Hole
④GPS Lamp
⑤CDMA Lamp
⑥Power Lamp
⑦Battery Cover
⑧Power Connector
⑨24pin Connector
4pin Car Alarm Box Connector

7
①Power Button If you want to turn on the device, push
the power button for 2 seconds at
least.
You can realize that the device power
on or not through the lamp.
It's the same way to turn off the
device.
②Emergency Reset When you need an emergency
download, you have to use this button.
The way is that push the emergency
reset button and push the power
button meanwhile.
③Screw Hole By using screws, you can fix a device
to your car tightly.
④GPS Lamp When a device takes GPS air-signal,
the lamp will be turned on orange color
and blink.
⑤CDMA Lamp When a device takes CDMA air-signal,
the lamp will be turned on green and
blink.
⑥Power Lamp When a device power on, the lamp will
be turned on red.
⑦Battery Cover To open cover, you should get rid of a
screw first.
⑧Power Connector Using enclosed power cable, you
should connect device to car constant
power (Battery).
⑨
24pin Connector
Software download
4pin Car Alarm Box
Connector Connect to car alarm box

8
5. Installation Manual
The installation location can be changed according to
the user’s preferences.
This manual recommends user to install using “Car
main power” for keeping permanent activation.
• Connecting power supply
Use the wire connected to the car main power for power
supply.
• Preparing the product
Make sure the positive (+) and negative (–) wire end of the
product.
• Connect the wire of product to car main power. At this time,
watch out the (+) and (–) polarity.
• The product is connected normally, if you can see the light
turned on the product.
• Finish the insulated wires by winding them with a tape
neatly, in order to prevent an electric leakage or short circuit.

9
• Installation
Install the product at the proper location inside of the car
where dust was removed and cleaned. The product can be
fixed using the tape attached to the rear side of the product
or the screw holes at both sides of the product. (At this time,
attach the product in such way that the LCD window faces
upwards for proper GPS reception.)
• Finishing
When the product is installed, the product is not seen by the
users with their naked eyes. And the product should be kept
away from heat sources.

10
1. Take center fascia apart from dashboard
1-1 Unscrew the center fascia marked.
1-2 Unscrew the center fascia marked.
It may differ slightly depending on the model