Kandolite K64P36W3RGBAW User manual

USER MANUAL
K64P36W3RGBAW

I n d e x
summarize ......................................................................... 3
safety instructi n ................................................................ 3
utside size picture ............................................................. 4
main functi n ...................................................................... 5
DMX c ntr ller functi n....................................................... 5
Display perati n instructi n............................................... 6
Manual instructi n............................................................... 7
Operating c ntr l instructi n............................................... 9
XRL c nnecti n instructi n .................................................. 9
C nnecti n picture .............................................................11
Expl ded Views ..................................................................13
illuminance list...................................................................14
Pr blem analyse.................................................................15
Technicals secificati n…………….…………………………..………17

Summarize
Thank you for purchasing our LED PAR lighting. Please read these instructions
carefully before begin and operate the fixtures according to these instructions to
avoid any possible da ages and accidents causes by isusage.
Pr ducts intr duce
This led K64P36W3RGBAW light is uses alu inu shell , designed in a fashion of
hydrodyna ic for . Appearance shows: long can, short can or short can with
color filter . It takes uses high power R,G,B,A,W 5 kinds LED. It uses power
switch, perfor s low weight and consu ption, stable capability and long life.
The built-in progra includes di er, strobe, eotic, gradual change, fading and
so on. International standard DMX 512 signal is requested.
Packing list
•K64P36W3RGBAW light 1PC
•DMX cable 1PC (Sold separately)
•The use anual
•Warranty Card
Safety Infor ation
! Enquire the skilled people before any repair;
! Always ake sure disconnect fro the power source before setting up, serving and
oving;.
! Avoid direct eye exposure to the fixture when it is on;
Safety instructi n
● Make sure the power supply voltages are consistent with this lights ， Ensure the
use of voltage is in the range of the request technical para eter.

●before the installation, please check the light’s fasteners and echanical
structure have been received in good condition and appear no da age.
● This light is designed for indoor use, working te perature is lower than 40
degree.
●The fixtures aybe ounted in any position provided there is adequate roo
for ventilation. Make sure there are no infla able and explosive ite s
(orna ents) in 0.5 eters away.
●Yellow / green cabling earthling safety; no flicker when the fixture is working on.
Outside Size Picture

Main Functi n
• high quality LED: low consu ption, brightness, stable capability and long life
•Each color of LED with 256 di ing, RGB each color has a good degree of
saturation.
•Liner Di ing 0%-100%, function of strobe, eotic, gradual change and
ju ping change
•DMX512 Controller ， 4 button set DMX ID address with led display
•auto run /sound activated/ aster slave/interconnected ulti- achine control
•using switching power supply to protect the LED to work well
•lens degree: 15º 、 25º 、 45º optional
•DMX512 channels:4,5,9 channels
•body color: black/white/optional
DMX C ntr l Functi n
4CH
Channel DMX Value C ntr l Functi n Remark
1CH 0-255 RGB ixing 0-100%
2CH 0-255 A 0-100%
3CH 0-255 W 0-100%
4CH 0-255 General di ing 0-100%
5CH
Channel DMX Value C ntr l Functi n Remark
1CH 0-255 R 0-100%
2CH 0-255 G 0-100%
3CH 0-255 B 0-100%
4CH 0-255 A 0-100%
5CH 0-255 W 0-100%

9CH
Channel DMX Value C ntr l Functi n Remark
1CH 0-255 General di ing
2CH 0-255 Red Di ing 0——100%
3CH 0-255 Green Di ing0——100%
4CH 0-255 Blue Di ing 0——100%
5CH 0-255 A ber 0——100%
6CH 0-255 White 0——100%
0-14 Di ing
7CH 15-255 Strobe Speed
When the 7CH
above31 ， this
function is
invalid
0-31 Invalid
32-63 Fro dark to bright
64-95 Fro bright to dark
96-127 Fro dark—bright—dark
128-159 RGB Gradient
160-191 dark-bright-dark Auto atic
192-223 5 colors ju ping change
8CH
224-255 Many color ixing ju ping
change
Must use CH1 、
2 、 3 、 4 ， 5
otherwise no
light ，
Fro the
9CH, start the
speed
adjust ent
9CH 0-255 Speed adjust
（ slow--quick ）
Display Operati n
•MENU : access the enu or return to a previous enu option
•ENTER: select the current enu option
•UP: enu selection or para eter incre ents
•DOWN: enu selection or para eters decrease

Manual Instructi n
Operating instruction
1 MENU is used to access the enu or return to a previous enu option. It can
not be used to select and store the current enu option. Press UP / DOWN to
choose a desired enu ite . Here are the operation details :
•”addr”: DMX ode （ A001-A512 ）
•SLAV”: Slave receive ode
•“CHnd”: DMX accept channel select (4, 5, 9)
•”SP”; built-in progra speed change odel (SP00-SP15, SP00 is the fastest)
•”Pr”; Built-in progra （ Pr00-Pr15 16 progra in all ）
•”ASC”; any colors ju ping （ AS00-AS15 speed adjustable ）
•”FAdE”: gradual change odel （ FA00-FA15 speed adjustable ）
•”FLAS”: white color strobe （ FL00-FL15 speed adjustable ）
•”rL”: red color brightness adjust ent ode （ r000-W255, r255 is the brightest ）
•”gL”: green color brightness adjust ent ode （ g000- g255, g255 is the brightest ）
•”bL”: blue color brightness adjust ent ode （ b000- b255, b255 is the brightest ）
•”uL”: white color brightness adjust ent ode （ u000- u255, u255 is the brightest ）
2Press ENTER to access the further enu setting. This process can be saved
auto atically; that eans you will enter the process saved previously when
you activate the light next ti e. For exa ple, if you want to choose DMX
ode A001, operate as follows:
•Press MENU, go back to the initial setting
•Press UP / DOWN until Addr
•Press ENTER to choose, the display will glinting at this o ent
•Press UP / DOWN to change the address code to select A001

• Press ENTER to select and store the current enu options. DMX ode
will be
• stored auto atically and the screen will stop glinting.
•DMX channel choosing Operation ： CHNd ode
•Press Menu, go back to the initial setting
•Press UP/DOWN ， until shows “CHNd”
•Press ENTER to access the enu ite s to select, the screen will now be
glinting
•Press UP/DOWN to change the DMX Channel: 4CH 、 5CH 、 9CH
•At last, press ENTER to confir , if it delay for 3 second , DMX channel
choosing will be saved, and go back to DMX receive ode(A001); If your
press ENTER for short ti e or not press , delaying for 8 seconds , the DMX
channel will select to be saved auto atically, and then go back to DMX
receive ode(A001)
3. Details of progra built inside （ Pr- - ）
•Press MENU, go back to the initial setting
•Press UP / DOWN until Pr--
•Press ENTER to choose, the display will glinting at this o ent
•Press UP / DOWN to change the address code to select pr00
• Press ENTER to select and store the current enu options. DMX ode
will be
• stored auto atically and the screen will stop glinting.
N te ： Pr32--- Pr35 Can change the content Of SP ， correct the speed of
ju ping change , SP00 is the fastest ， SP15 is the slowest
•Pr00--- Pr31: R,G,B,A,W single color or ulti-colors lighting
•Pr32 ： 5 colors ju ping
•Pr33 ： 5 colors ju ping+strob
•Pr32 ： uilt colors ju ping
•Pr33 ： uilt colors ju ping+strob

Operating C ntr l Instructi n
Master/Slave
Master ： The aster should set as built-in progra and shows” P - X – X” send out
synchronization signals. To avoid the host signal and DMX512 signals interfere
with each other, should cut off the DMX512 signals. The signal lines are longer
than 60 eters should increase a signal a plifier.
Slave ： It ust be in the SLAV ode and the address code should be A001 to assure
receive the aster’s signals correctly. Only one light can be set as a Master and
others are slaves.
XLR cable c nnecting
XRL cable：
：：
：
The stand connection way of the XRL is: one end connects to the ale plug, and
the other connects to the fe ale.
Noted
：
In order to avoid failures and interference signal trans ission
，
we connect
a resistance120Ω
（
1/4W
）
at the end of the DMX connecting as below:

The Conversion between 3pin and 5 pin XLR
If the output cable of DMX512 controller is the 5PIN, please use 1pc 5PIN to
3PIN cable

C nnecting picture
Cable connecting picture：

Electrical wiring diagram

Expl ded views

Luminance list

Pr blem Analyze
Proble Checking way
Can not turn on the
light
Check the power source plug is in nor al or not
Check the switch of the lights is off or on
Check it the fuse if in nor al
DMX can not control
it
Check the DMX cable is connect to the lights or not
Check the DMX512 controller work in nor al or not
Check the DMX cable is nor al or not
Check if the lights is in DMX ode（ A001）
Display not bright
When connect to the electricity， did the led flash one ti e?
If so， the power source is nor al; If not， please check if the
switch and the transfor er has power out
Check if the power input of the IC board is nor al
Check if the cable connect to the display loose
Change the ain board to see if it is nor al.
Chang the display
LED not light
When connect to the electricity， did the led flash one ti e?
If so， the power source is nor al; If not， please check if the
switch and the transfor er has power out
Check if the power input of the IC board is nor al
Check if the cable connect to the display loose
Change the ain board to see if it is nor al.
Chang the display
LED is connect by leds in series first, then connect parallel,
so please check if the leds is loose

So e of the LED not
light
 Use the ulti eter to check if the led is bright or not, of
not, please change the led
check whether current li iting resistor is nor al or not
Check constant current IC is nor al or not (co pared with
the nor al IC)
Single color leds
always bright/not
bright
Check the switch of this color is nor al or not
Change the IC control board
Noted: only professional persons can do as above
！

Technical Specificati n
•Input voltage ： AC 100V-264V/47-63HZ
•Output voltage ： DC24V
•Consu e ： 60W （ 36*3W ： 120W ）
•La p Type ： High Power LED(1W/3W)
•La p Spec ： R(6PCS) ， G(8PCS) ， B(8PCS) ， A(6PCS) ， W （ 8PCS ）
•Control Signal ： DMX512, sound activated, auto run
•Control ode ： stand alone/ sound activated
•Channel ： 4,5,9CH
•Color effect ： RGBAW ixing
•Function Effect ：
：：
： di er, strobe, eotic, gradual change
•Bea Angle: 15°, 25°,45°
•Cooling ode: Fun
•Anti-electricity intension ： 1.5KV
•Insulation Resistance ：＞２ MΩ
•Size:300*220*230
•Net Weight ： 2.5KG

Copyright 2012 KANDOLITE. All rights
reserved. Due to continuous i prove ents
and innovations, specifications ay change
without notice.