SmartCard Reader
Mounting Instructions
Follow these instructions to install the reader:
1. Pull the controller’s wires in the wall through the hole in the mounting
bracket.
2. Affix the mounting plate to the wall using two screws (#6-32).
3. If a higher level of tamper detection is desired, cut the plastic tamper
tab from the mounting bracket.
4. Secure the white reflector tab back into the mounting plate hole with a
screw. (#6-32).
5. After having wired the reader as per the drawings below, insert the top
hook of the cover into the mounting plate tab and complete the pro-
cedure by pressing the bottom part into place until the bottom hook is in
place.
6. If a more secure installation is desired, install the provided screw at the
bottom of the reader. You may also use the provided security screw
instead for an even safer installation. (#6-32).
FCC COMPLIANCE STATEMENT
CAUTION: Changes or modifications not expressly approved by KANTECH could void your authority to use
this equipment.
This equipment generates and uses radio frequency energy and if not installed and used properly, in strict
accordance with the manufacturer’s instructions, may cause interference to radio and television reception. It
has been type tested and found to comply with the limits for Class B device in accordance with the spe-
cifications in Subpart “B” of Part 15 of FCC Rules, which are designed to provide reasonable protection
against such interference in any residential installation. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause interference to television or radio reception,
which can be determined by turning the equipment off and on, the user is encouraged to tryto correct the inter-
ference by one or more of the following measures:
-Re-orient the receiving antenna
-Relocate the alarm control with respect to the receiver
-Move the alarm control away from the receiver
-Connect the alarm control into a different outlet so that alarm control and receiver are on different circuits.
If necessary, the user should consult the dealer or an experienced radio/television technician for additional
suggestions. The user may find the following booklet prepared by the FCC useful: “How to Identify and
Resolve Radio/Television Interference Problems”. This booklet is available from the U.S. Government Print-
ing Office, Washington D.C. 20402, Stock # 004-000-00345-4.
INDUSTRY CANADA STATEMENT
CAN-ICES-3(B)/NMB-3(B)
Wiring Chart via Wiegand Wiring Chart via RS485
Wiring Chart via RS485 (Lock Wiring)
UL294 Performance Levels:
Destructive Attack: Level I (no attack test)
Line Security: Level III (AES128 line security)
Endurance: Level IV (100,000 cycles)
Standby Power: Level I (no integral standby power)
Installation location and wiring methods shall be in accordance with the
National Electrical Code, ANSI/NFPA 70. There is no maintenance
required and there are no replacement parts required for these devices.
_____________________________________________________________________________________________________________________
This device complies with Part 15 Class B of the FCC rules. Operation is subject to the following two conditions: (1)
this device may not cause harmful interference, and (2) this device must accept any interference received including
interference that may cause undesired operation. This class B digital apparatus meets all requirements of the Cana-
dian Interference Causing Equipment Regulations CAN ICES-3 (B) / NMB-3 (B).
Mullion
FCC ID: V8515KTMULMTKP
IC: 5690B-KTMULMTKP
Single Gang
FCC ID: V8515KTSGMTKP
IC: 5690B-KTSGMTKP
Copyright © 2015 Tyco International Ltd. and its Respective Companies. All rights reserved • Specifications may change without notice
Tel.: 1 (450) 444-2030 • Toll Free: 1-888-222-1560 • Fax: 1 (450) 444-2029 • www.kantech.com
D29009033R001
Models:KT-MUL-MT and KT-MUL-MT-KP
FCC ID: V8515KTMULMTKP
IC: 5690B-KTMULMTKP
.
Models: KT-SG-MT and KT-SG-MT-KP
FCC ID: V8515KTSGMTKP
IC: 5690B-KTSGMTKP
Models: KT-MUL-SC and KT-MUL-SC-KP
FCC ID: V8515KTMULSCKP
IC: 5690B-KTMULSCKP
.
Models: KT-SG-SC and KT-SG-SC-KP
FCC ID: V8515KTSGSCKP
IC: 5690B-KTSGSCKP
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
