Kaon KS0382 User manual

For further information contact KAON on 07 3180 1470 or [e-mail]
FITTING INSTRUCTIONS FOR
Reversing Camera Relocation Bracket
SKU COMPATIBILITY
KS0382 Toyota FJ Cruiser
Included contents
QTY COMPONENT QTY COMPONENT
1 Spare Tyre Mount Bracket 1 M6x16 Socket Head Cap Screw
1 Camera Bracket 1 M6 DIN Washer
1 M10x1.25 x 30 Hex Bolt G8.8 2 M6 Nyloc Nut
1 M10 DIN Washer 2 Small Cable Tie
1 M6x12 Socket Head Cap Screw
20 minutes / Half a beer
Time

2
Bolt Torque
DIAMETER (mm) 5mm 6mm 8mm 10mm 12mm
NEWTON-METRES (Nm) 5 Nm 9 Nm 22 Nm 44 Nm 77 Nm

3
Let’s get to work.
Preparation
1. To start with, remove the spare
tyre and clean any dusty or dirty
surfaces.
2. The camera is nested within a
metal bracket using three M8 bolts,
remove those with a 12mm socket.
3. Once removed, unplug the camera
bypressing the clip as shown.
If built-up dust makes it tough to
remove, use a small screwdriver
tolift the tab.
4. Free the cable from it’s mounting
position by locating the white clip
at the base of the spare tyre mount.
Push the tab as shown towards the
door and the cable should come free.
2
4
3

4
Attaching the Camera
1. Remove the shroud and screws
fromthe back of the factory
camerabracket.
2. Attach the camera to the smaller
supplied pivoting Camera Bracket,
using the small screws removed
earlier. Ensure that the serial
number (top of the camera) faces
the top of the bracket as shown,
soyour camera is the right way up.
1
2

5
Bracket Installation
1. Loosen all the bolts holding the
spare tyre carrier, and remove the
bottom right one altogether.
2. Position the Spare Tyre Mount
Bracket under the bottom corner,
ensuring the raised edges of the
bracket sit firmly against the sides
of the carrier. Use thesupplied
M10 Bolt and Washer to secure
itinplace.
3. Once in position, tighten all the
bolts on the spare tyre carrier.
2
2
3

6
Camera Installation
1. Locate the small slot in the Spare
Tyre Mount Bracket and insert
the white clip you freedearlier,
aspictured.
2. Loosely attach the Camera Bracket
with the camera installed to the
larger Spare Tyre Mount Bracket,
using the Socket Head Cap Screws.
Use the M6x12 and one Nyloc nut
in the top hole, and the M6x16,
M6 Washer and a Nyloc nut in the
bottom hole slotted hole as pictured.
3. Plug the camera in.
1
2
3

7
Camera Installation cont.
4. Position the cable underneath the
bottom edge of the bracket and
secure in place using the supplied
cable ties.
5. We’d suggest you re-attach the
spare tyre before adjusting the
angle and tightening the Camera
Bracket, as the tyre will sit slightly
within frame.
6. Once you’re happy with the
view, tighten the screws on the
CameraBracket.
7. You’re all set! Now you don’t
need todo a Stevie Wonder
impersonation when reversing
witha bin bag fitted.
4
5
6

8
Disclaimer: The products sold by KAON should not be modified, and are for use only on the vehicles specifically stated. KAON will not be
liable for any damages arising out of the use or misuse of it’s products. It is the customers responsibility to ensure the products are safely
and properly used and installed. KAON consistently seeks to improve it’s products and reserves the right to make changes to any product.
Local Knowledge & Assistance
We know half the fun of building your dream 4x4 is getting your hands
dirty. But we also know that sometimes, things don’t go to plan. If in the
pursuit to build the ultimate setup you find yourself off-track, we’re here
tohelp you get unstuck.
For further information call 07 3180 1470 or email [email protected]om.au