Kathrein UFC 662sw User manual

Operating manual
DVB cable receiver
UFC 662sw

2
PREFACE
Dear customer,
this Operating Manual is intended to help you make the fullest use of the extensive range of functions
offered by your new cable receiver.
We have tried to make the operating instructions as easy as possible to understand, and to keep them
as concise as possible. To help you understand particular specialist terms that cannot be translated,
we have added a short glossary at the end of the manual.
The power switch is an environmentally friendly feature. If you will not be using your receiver for an
extended period, you should use the power switch to disconnect it from the power supply and save energy.
For shorter breaks, you can use the remote control to switch the receiver to standby, which uses only a
minimal amount of energy.
We wish you good reception and much pleasure using your new DVB-Cable receiver.
Your
KATHREIN team

3
IMPORTANT INFORMATION
The channels available on the cable network are subject to continual change. When such changes occur
it is necessary to reset the channels. The information for these settings can be found on the Internet
or in relevant magazines.
The information in this operating manual was correct at the time of going to print. We reserve the right
however to make changes at any time and without prior notice. If new software is released for your
receiver, and this affects the information in the operating manual (e.g. changes to the menus and/or
functions), if we believe it necessary we will make available a new operating manual for download under
“www.kathrein.de”.
Please keep the original packaging in case you need to return the product at any time. If the
product is not properly packed, the warranty claim is invalidated.
Make a note of the receiver's basic settings (these are set during the first installation), so you can
restore them if necessary!
Before you switch off the receiver using the power switch, you must switch the remote control into
stand-by mode by pressing the stand-by button. In stand-by mode, any changed data that is broadcast
will be saved by the receiver. Once the receiver is in standby mode it can be fully switched off at any
time at the power switch at the front of the unit. Do not switch the receiver off at the power switch
when it is in operating mode! This can lead to a loss of data and corruption of the software.
INFORMATION ON AUDIO MPEG INC. AND S.I.SV.EL, S.P.A:
This unit makes use of legally protected technologies, which are protected by patents in the USA and
also by other intellectual property rights in other countries. KATHREIN-Werke KG has obtained licences
from Audio MPEG Inc. and Societa‘ Italiana per lo sviluppo dell‘elettronica, S.I.SV.EL, S.P.A to use
these technologies. These licences carry certain restrictions, which apply also to you as the customer.
Accordingly this unit may only be used by the end customer for private non-commercial purposes and
for the licensed content. It may not be used for commercial purposes. The use of products or processes
that are sold or used with this unit is not included in this statement. The use of reverse engineering is not
permitted in respect of the licensed technologies, nor is disassembly.
Manufactured under licence from Dolby Laboratories. “Dolby” and the
double-D symbol are registered trademarks of Dolby Laboratories.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks
or registered trademarks of HDMI Licensing LLC.
®

4
CONTENTS
PREFACE ................................................................................................................................. 2
IMPORTANT INFORMATION ...................................................................................................... 3
CONTENTS............................................................................................................................... 4
SAFETY INSTRUCTIONS - IMPORTANT INFORMATION ............................................................. 6
RECEIVER FEATURES/SCOPE OF SUPPLY............................................................................... 8
FEATURES ............................................................................................................................... 9
FEATURES ............................................................................................................................. 9
CONTROLS, DISPLAYS AND CONNECTIONS .......................................................................... 10
CONNECTION AND SETUP ...................................................................................................... 11
CONNECTION EXAMPLE....................................................................................................... 12
REMOTE CONTROL................................................................................................................ 14
FIRST INSTALLATION ............................................................................................................. 15
OPERATING INSTRUCTIONS .................................................................................................. 19
MENU CONCEPT .................................................................................................................. 19
MENU OVERVIEW................................................................................................................. 20
ALPHANUMERIC INPUTS ...................................................................................................... 21
LANGUAGE SETTING - OSD.................................................................................................. 21
ON-SCREEN DISPLAYS (OSD) ................................................................................................ 22
CHANNEL MESSAGES .......................................................................................................... 22
CHANNEL INFORMATION...................................................................................................... 22
SELECT AUDIO TRACK ......................................................................................................... 23
ERROR REPORTING............................................................................................................. 23
CHANNEL LIST - TV/RADIO ................................................................................................... 23
EPG - ELECTRONIC PROGRAMME GUIDE .............................................................................. 25
CALLING UP THE EPG .......................................................................................................... 25
“CURRENT” VIEW ................................................................................................................. 26
“PREVIEW” VIEW (PROGRAMME LISTINGS).......................................................................... 27
ADDITIONAL INFORMATION (i BUTTON)................................................................................ 28
RECORDING (TIMER)............................................................................................................ 29
ONCE-ONLY RECORDING ..................................................................................................... 30
DAILY RECORDING .............................................................................................................. 30
RECORD WEEKLY ............................................................................................................... 31
TIMER LIST VIEW.................................................................................................................. 32
VIDEOTEXT (TELETEXT)......................................................................................................... 33
EDIT TV-CHANNELLIST .......................................................................................................... 34
SELECTION OF THE LIST/CHANNELS TO BE EDITED............................................................ 34
EDITING LISTS/CHANNELS................................................................................................... 35
“LAST FUNCTION” MEMORY .................................................................................................. 36
MOVE CHANNELS ............................................................................................................... 36
DELETE CHANNELS............................................................................................................. 36
SKIP CHANNELS ................................................................................................................. 36
LOCK CHANNELS ................................................................................................................ 37
COPY CHANNELS TO THE FAVOURITES LIST ........................................................................... 37

5
CONTENTS
START BLOCKSELECTION (HIGHLIGHTING SEVERAL CHANNELS) .............................................. 37
EDIT TV-CHANNELLIST ......................................................................................................... 38
REMOVE FROM FAVOURITES LIST ......................................................................................... 38
LOCK CHANNELS ................................................................................................................ 39
RENAME FAVOURITES LIST .................................................................................................. 39
START BLOCKSELECTION (HIGHLIGHTING SEVERAL CHANNELS) .............................................. 39
SEARCH CHANNELS (CHANNEL SEARCH)............................................................................. 40
AUTOMATIC (CHANNEL) SEARCH......................................................................................... 40
MANUAL (CHANNEL) SEARCH .............................................................................................. 42
ADVANCED CHANNEL SEARCH ............................................................................................ 43
PARENTAL CONTROL............................................................................................................. 45
LOCK MAINMENU ................................................................................................................. 45
LOCK SET-TOP-BOX ............................................................................................................. 45
DEFINE NEW PIN CODE........................................................................................................ 45
SETTINGS .............................................................................................................................. 46
FIRST INSTALLATION............................................................................................................ 47
REGION................................................................................................................................ 47
TV SETTINGS (TV, VIDEO AND AUDIO) .................................................................................. 47
SUIT SCREEN MENU ............................................................................................................ 49
DATE AND TIME .................................................................................................................... 50
COMMON INTERFACE .......................................................................................................... 50
SERVICE MENU ...................................................................................................................... 53
FACTORY RESET.................................................................................................................. 53
CONNECTING UP THE VIDEO/PVR ......................................................................................... 54
RECORDING......................................................................................................................... 54
USING THE FRONT PANEL/SERVICE ...................................................................................... 55
TECHNICAL APPENDIX........................................................................................................... 56
SCART SOCKET ASSIGNMENT ............................................................................................. 57
VHS/S-VHS SWITCHING........................................................................................................ 57
SHORT TECHNICAL GUIDE .................................................................................................... 58
TROUBLESHOOTING.............................................................................................................. 60

6
SAFETY INSTRUCTIONS - IMPORTANT INFORMATION
Mains cable
Make sure that the mains cable
(power supply cable) is not damaged.
Units with a damaged mains cable
must be disconnected from the mains
(unplug it at the socket) and repaired
by an electrical specialist before
setup. Only use the power pack
supplied (if available)!
Risk of fatal injury due to electric
shock!
Danger!
Cleaning
Disconnect the mains plug before
cleaning the unit. Only use a dry
cloth for cleaning and only clean
the outer surface. Never open the
casing of the unit.
Touching the parts inside the unit
carries a risk of death due to electric
shock!
Playing children
Make sure that children do not push
any objects into the ventilation slots.
Risk of fatal injury due to electric
shock!
Earthing
The antenna system must be earthed
as specified or equipotentially
bonded.
EN 60728/11 and any national
regulations must be complied with.
Risk of voltage surges due to
lightning strikes!
Power supply voltage
Only operate the unit at the specified
mains voltage (indicated on the
rear of the unit or on the external
power pack). The unit may only be
connected to the mains and turned
on once it has been connected to
the antenna and to the TV set or the
cable network and PC.
If the mains voltage is too high, there
is a risk of fire!
Moisture, direct sunlight, heat,
naked flames
Protect the unit against moisture,
dripping and splashed water (do
not place any filled objects such
as vases on top of the unit). Do not
place the unit close to a heater or
expose it to direct sunlight and do
not operate it in damp locations. Only
use the unit in a moderate climate,
not in tropical conditions! Place
no naked flames such as candles
on top of the unit!
There is a risk of fire!
Ventilation
The heat generated in this unit is
adequately dissipated. However,
the unit should never be installed
in a cupboard or on shelves with
inadequate ventilation. Never cover
the cooling slots on the unit (e.g.
with other equipment, magazines,
tablecloths, clothing or curtains)!
Batteries
If your unit was supplied with
batteries (e.g. for the remote control),
take care that the batteries are
not exposed to excessively high
temperatures, direct sunshine or
fire. Exchange the batteries only
with types that are identical or
equivalent. Otherwise the batteries
and also the remote control may
be damaged. Comply also with the
safety instructions stated on the
batteries:
There is a risk of explosions!
Warning!
Warning!
Warning!
These two pages contain important information about operation, installation location and connection
of the unit. Read these instructions carefully before setting up the unit.
Do not
cover

7
Periods of extended absence,
thunderstorms, mains socket
accessibility
In order to disconnect the unit from
the mains completely, the mains
plug must be unplugged from the
wall socket! Therefore install the unit
close to a mains socket and make
sure that socket is accessible at all
times, so that you can disconnect the
unit from the mains if necessary.
If you are away for an extended
period, and during thunderstorms,
always switch the unit off at the
mains and unplug it from the socket.
This also applies to the other
equipment connected to the unit.
Isolation from the cable network is
also recommended. Note any timer
programming (receiver) and turn the
unit on again promptly before the
recording time.
Installation location
All electronic equipment generates
heat, However, the heating of this
unit lies within the permissible range.
Sensitive furniture surfaces and
veneers may become discoloured
by the effects of constant heat over
time. The feet of the unit can also
cause colour changes to treated
furniture surfaces. If necessary, place
the unit on a suitable stable and
flat base!
Repairs
Ensure that any repairs to your unit
are carried out by qualified personnel.
Opening the unit and attempting to
repair it yourself voids all warranty
claims!
Improper work on the unit may
jeopardise the electrical safety of the
unit.
The manufacturer accepts no liability
for accidents caused by the user
opening the casing of the unit!
Connections
Incorrect wiring of the connections
can lead to malfunctions or defects
on the unit!
Important
Do not place any objects on top
of the unit. Unless stated to the
contrary in the “Connection and
Set-Up” and “Installation” sections
in the manual supplied, maintain a
clearance of at least 10 cm above
the unit, 2 cm to either side and 5 cm
behind the unit, to allow unobstructed
dissipation of the heat generated.
There is a risk of fire!
Electronic equipment is not domestic
waste - it must be disposed of
properly in accordance with directive
2002/96/EC OF THE EUROPEAN
PARLIAMENT AND THE COUNCIL
dated 27th January 2003 concerning
used electrical and electronic
appliances.
At the end of its service life, take this
unit for disposal to an appropriate
official collection point.
Spent batteries are special waste!
Do not throw spent batteries into
your domestic waste; take them to a
collection point for spent batteries!
SAFETY INSTRUCTIONS - IMPORTANT INFORMATION

8
RECEIVER FEATURES/SCOPE OF SUPPLY
The UFC 662sw receiver is suitable for the reception of digital cable TV and radio channels.
The HDMI interface offers the optimum capability for connecting the receiver to a flat-screen TV set.
The built-in up-scaler processes the picture optimally for flat-screen TV sets.
Features are for instance: Kathrein EPG, guided first installation with country setting, electric
audio output for Dolby Digital (AC 3), a video cinch output and Teletext with an 800-page memory.
The receiver is available in a black housing.
- UFC 662sw
- Remote control RC 671
- Scart cable
- 2 batteries AAA 1.5 V
- Power supply unit 230 V/12 V
- EMU 06, F adapter (F to IEC)
- Operating manual
- Safety Notes
SCOPE OF SUPPLY

9
FEATURES
FEATURES
Reception of digital cable TV and radio
channels
HDMI output for good picture quality on your
flat-screen TV set
Up-scaler for upscaling the Pal signal (576i)
to 576p, 720p and 1080i
4-character display
Common Interface for one CA module ¹)
Kathrein EPG with timer programming ²)
Guided first installation with country setting
Sorting by the pre-programmed channel list
Suitable for downloading software and
channel lists via a PC
8 favourite channel lists for TV and 8 for radio
On-screen display (OSD) in 8 languages
(D, GB, F, I, E, CZ, NL, TR)
14 timers; conveniently programmable using
the EPG
Language selection for multilingual
broadcasts
Electrical audio output for
Dolby Digital data stream (AC 3)
Scart socket programmable for
composite colour and RGB signal output
Cinch sockets for AV signal
Videotext decoder with 800 page
memory capacity and Videotext generation
(only via Scart)
Automatic 4:3 and 16:9 format recognition
(choice of viewing format)
Channel search
Automatic date and time generation via
DVB data stream
Programme position sort function
4,000 channel memory
Infra-red remote control
On/off switch (disconnection from the
12 V supply) 3)
Connection for external IR sensor
(available as accessory)
Compatible with the UFO®compact
processing system
¹) CA modules and Smartcards are not included with this product
²) Displayed only if this information is broadcast by the channel provider
3) The unit is not fully disconnected from the mains (see the sections “Safety Instructions - Important Instructions”
and “Periods of extended absence, thunderstorms, mains socket accessibility”)

10
CONTROLS, DISPLAYS AND CONNECTIONS
This section provides a brief description of all the controls, displays and connections.
Front Panel Controls and Displays
1. On/Off switch
1)
2. Channel select buttons (▼▲)
3. Display
Rear Panel Controls and Displays
1. RF(HF) input
2. RF(HF) loop-through output
3. Common Interface for one CA module
for Pay-TV cards 2)
4. Video output (composite colour)
5. Electrical digital data stream output
(SPDIF/Sony Philips Digital Interface
Format) for Dolby Digital AC 3 audio
6. Audio outputs (L/R) - cinch sockets
7. HDMI Output
8. RJ 11 data interface/connection
port for an external IR sensor
9. Scart socket for TV connection
10. Mains power cable

VIEW OF FRONT PANEL (FLAP REMOVED)
VIEW OF REAR PANEL


1) The unit is not fully disconnected from the mains
(see the sections “Safety Instructions - Important
Instructions” and “Periods of extended absence,
thunderstorms, mains socket accessibility”)
2) CA modules and Smartcards are not included with
this product

11
CONNECTION AND SETUP
The following section is intended specifically for specialist dealers. You need not refer to this section
unless you are carrying out the installation yourself.
The “Connection examples” section provides a sample configuration.
Do not connect the receiver to the power supply until all installation work has been properly carried out.
Refer to the information in the “Safety instructions” section.
When fitting the connector, make sure that no wires from the braid are touching
the inner conductor, otherwise a short circuit will occur.
The quality of the reception signal depends on this connection!
CONNECTING THE RECEIVER
The serial number sticker for the UFC 662sw is located on the underside of the unit.
The information printed on it includes the following:
- the exact designation (e.g. UFC 662sw)
- the part number and
- the serial number of the unit.
You do not need this information in order to operate the unit. If however, contrary to
expectations, you need to make a claim under warranty and you do not have the packaging
for the receiver to hand, you can find the above information about the unit on this sticker.
Connect the RF input of the receiver to the antenna socket. For this, use a coaxial cable
with a plug to with the F standard or the IEC standard (in combination with the F adapter
supplied with the receiver).
If the IEC connector is not yet fitted to the cable, strip the insulation from the cable as
shown in the following illustration and carefully fit the connector on to the end of the cable
so that it is securely fitted.
Fitting a plug to the
“F” standard
Fitting a plug to the
“IEC” standard
Lengthwise slits (3x) Bend back Screw together

12
Scart
Scart
Digitalton AC 3
elektrisch
Infrarot-Empfänger
(optional)
CONNECTION EXAMPLE
CONNECTION AND SETUP
Dolby Digital system
Infra-red receiver
(optional)
Digital audio AC 3
electrical
HiFi system

13
CONNECTION AND SETUP
If you want to play the sound on your hi-fisystem, connect the audio cinch sockets to the input sockets
on the hi-fisystem, using an appropriate cable (see “Connection example”).
The electric digital output is intended for the connection of a Dolby Digital system (see “Connection
example”).
TV AND VCR CONNECTION
AUDIO CONNECTION
ELECTRICAL DIGITAL OUTPUT
INSERTING BATTERIES INTO THE REMOTE CONTROL
Connect the cable receiver (HDMI or alternatively TV Scart socket) and the TV set using an HDMI or
Scart cable (see “Connection example”). If your TV is stereo, you can receive the sound in stereo via
the HDMI or Scart connection.
For system reasons, the same video signals are to be found at the TV Scart socket as at the video cinch
output.
Use a Scart cable to connect the cable receiver (TV Scart socket) to the video recorder/PVR.
Remove the cover on the rear of the remote control. Insert the two batteries supplied into the remote
control. Ensure correct polarity of the batteries; the + and – markings as indicated inside the battery
compartment. Slide the cover back onto the housing until it locks in place.
Connecting a video recorder/PVR to the TV Scart socket allows you only to
record. It does not allow you to play back on the TV set via the receiver. If you
are recording via an external video recorder/PVR, remember not to operate the
receiver during recording, otherwise all the on-screen displays will appear on your
recording.

14
REMOTE CONTROL
"
Sound on/off
... 
Numeric input for
channels, timers etc.

Open the main menu,
leave the menu and
return to the TV picture
#FAV (red)
Call up favourites selection
$PIP (green)
“Current” view in the EPG

Volume

Leave the menu
step by step

Changing channel in the
programme preview (EPG)
A
Currently not used
(red)
Recording in EPG,
editing in channel list
?
Power on/stand-by

Videotext (Teletext)
%OPT (yellow)
Open channel options
sound/subtitles selection
&TV/R (blue)
Switch between TV/radio
!
Access Channel
Notification/Info

AV mode
'
Channel selection
up/down

Confirm entry
open channel list
@
Cursor buttons

Open EPG (Electronic
Programme Guide)

Changing channel in the
programme preview (EPG)

Stop recording
The button symbols shown here can also be found in the
description of the operating steps.

15
FIRST INSTALLATION
Before using your receiver for the first time, read the “Safety Instructions” and
“Connection and Setup” sections.
The “Connection examples” section provides a sample configuration.
Do not connect the receiver to the power supply until all installation work has been
properly carried out.
The guidance given in the “First Installation” section assumes that the receiver
has been properly connected as per the “Safety Instructions” and “Connection
and Set-Up” sections.
First switch your TV set on and select the AV channel slot. Switch on your receiver at the power switch
at the front of the unit. The following display appears:
Select the menu language you want using the  buttons. Available options: German, English,
French, Italian, Spanish, Czech, Dutch and Turkish.
Press the $(green) button to move to the next menu.
Also note the bars at the bottom
of the on-screen display! These
provide information on what
to do next.
Note: If you are unsure whether you chose the right option from a previous menu, you can go
back a step at any time during the first installation process by pressing the #(red) button.

16
Use the @buttons here to select the settings for your TV set.
When doing this, refer to the operating instructions for your TV set!
TV aspect ratio
Here you can select the TV picture format. Either
4:3 or
16:9
FIRST INSTALLATION
Use the  buttons here to select whether you wish to use the factory pre-programmed channel
sorting for the selected country. This function is however active only if you select the setting “On” for
“Logical Channel Number” in the next line. Press the  buttons to access the next line.
Use the  buttons here to select whether the channels that are found during a channel search
should be sorted in accordance with the channel list saved for the previously selected country.
For example:
- “Germany” “Das Erste, ZDF, ...”
- “Austria” “ORF 1, ORF 2, ...”
- ...
- “Off” Channels are sorted in the order they are listed in the channel list
The following display appears:
Press the $(green) button to move to
the next menu.
The following display appears:

17
FIRST INSTALLATION
Picture format
Here you can select the type of screen display, depending on the setting of your TV format:
- TV format “4:3”: Pan & Scan or Letterbox
- TV format “16:9”: “automatically” or “always 16:9”
TV-SCART-Output
Select the type of video signal at the TV Scart socket here. Select the signal that your TV set can process.
- FBAS - composite colour signal (colour/picture/blanking/synchronous signal) or
- RGB - Red/Green/Blue signal
HDMI Format
Here please select the format (resolution) that will be output at the HDMI socket. Select the resolution
appropriate to your TV set.
Available options: “Auto” (automatic format choice), 576p, 720p or 1080i
Press the $(green) button to move to the next menu. The following display appears:
Execute Channel search
If you do not want to perform a channel search, press the $(green) button and continue with the “Date
and time” section. If you do want to perform a channel search, use the  buttons to select “Yes”.
Since the unit is supplied with an empty channel list, we recommend you start a channel search.
If you selected “yes”, you can press the button to progress to the next selection item.
Channel Search Mode
Use the  buttons to select whether you wish to search “free and scrambled” or “only free”
channels.
Press the button to move to the next selection item.

18
Local time offset
Use the  buttons to set the local
time offset from UTC (formerly GMT)
(e.g. for Great Britain +0 hours).
Use the  buttons to switch to
the “Automatic clock change” field. Use
the  buttons to select whether
the receiver should automatically
change over to and from summer and
winter time. If “On” is selected, the
receiver automatically sets itself to the
Use the button to move to the next step of the first installation. The following display appears:
FIRST INSTALLATION
Network Search
Use the  buttons (On/Off) to select whether a network search should be executed. If you set
this to “On”, the networking of the transmission channels enables additional transmission channels
that have not yet been saved to be located. They are then saved and searched for new channels in the
same way as the existing channels.
If you set this to “Off”, only the factory-set frequency range will be searched.
Press the $(green) button to start the channel search, or if you set channel search to “Off” you are
guided straight to the next item in the first installation process.
When the search has been completed, you will see the following message (example):
right time. If “Off” is selected, the field for manual selection of summer and winter time is displayed below.
Press the  buttons to perform the setting.
Press the $(green) button to close First Installation and return to the TV picture.
(UTC)

19
OPERATING INSTRUCTIONS
The structure of the menu concept is based on logical operating sequences. The programme showing
on the current selected channel always appears in the top right-hand corner of the screen.
You will find detailed descriptions of the selected menu items in the relevant sections of the
operating manual!
Note: The selected menus, sub-menus and positions, as well as the parameters to be set, are
each highlighted in colour. The menus are self-explanatory.
Note the bar at the bottom of the
on-screen display! This provides
information on what to do next.
Press the button to open the main menu, and use the  buttons to select the sub-menus.
Press the button to access the sub-menus. Use the  buttons to select the sub-menu options.
The settings under the various options are made either by pressing the  buttons or using the
numeric pad. You can exit the main menu and sub-menus and the various options step-by-step by pressing
the button (the settings/changes you made are saved). Press to return directly from one of
the menus to the TV picture (the settings/changes you made are saved).
MENU CONCEPT

20
MENU OVERVIEW
OPERATING INSTRUCTIONS
Mainmenu
Open the menu by pressing the button