As continuous product improvement occurs, specifications may be changed without notice.
DESCRIPTION
The Keating Instant Recovery®10×11”TS Fryer consists of a
frying vessel 10×11", having a splash deck and a splash back
installed in a cabinet equipped with gas burners and an
automatic temperature control mechanism, all arranged and
designed for the proper frying of food.
SPECIFICATIONS
Fryer Vessel shall be constructed from 18 gauge stainless
steel, shall have a shortening capacity of 26 pounds, shall be
equipped with two 18 gauge stainless steel horizontal heat
transfer tubes spaced above the bottom of the vessel so that
the bottom is unheated and the food particles collecting in
this bottom zone are unheated and therefor do not
carbonize. The frying vessel shall be polished to inhibit
carbon build-up and facilitate easy clean-up. The heat transfer
tubes shall be 3" wide and 5" high. The bottom of the vessel
shall slope toward the front where it shall be equipped with a 1"
Teflon core 1/4turn, drain valve, so arranged that the shortening
can be drained into a receiving vessel placed in front of the fryer.
Splashdeck shall slope toward the shortening containing vessel.
The splash deck shall be made of 16 gauge 304 stainless steel.
Splashback shall be made of 18 gauge 304 stainless steel,
shall completely cover the sides of the flue.
Cabinet: shall be made of 18 gauge stainless steel. The
cabinet shall be rigid in construction and shall have four 8"
adjustable legs. A door made of 22 gauge 304 stainless steel
shall cover the front of the cabinet and shall extend from the
bottom of the fryer to the panel, and above the panel shall be a
canopy. The door shall be the full width of the cabinet. No
additional space is required for the door to open a full 90
degrees. A stainless steel flue deflector is provided for installing
onto the flue back.
Heat Transfer Tubes to be two, made of stainless steel
polished to a #7 mirror finish.
Thermostat to be close range, hydraulic type and be accurate to
±3°F from 300° to 350°F with stainless steel bulb. Application of
this thermostat is patented by Keating.
Hi-Limit Control to be manually resettable type with stainless
steel bulb.
100% Safety Shut Off to be flame switch type with combination
control gas valve.
Melt Cycle to be standard on "TS" fryers, allowing the safe
melting of solid shortening. Fryer is to be left in the Melt Cycle
mode until oil completely covers heat transfer tubes.
Indicating Lights & Switches. Power on switch, push to light
switch, fry off melt switch, ready to fry light, over max temp
light.
Standard Accessories to include two timers (programmable for
three products each), one pair 4 mesh baskets, grid screen over
heat transfer tubes, drain clean out rod, sample of Keating
Klenzer and Sea Powder.
Electrical Requirements: Supply Voltage 120V 60Hz. Control
Voltage 24V 60Hz. 120 VAC 9ft. (1.5 m) grounded cord set
provided.
Gas Requirements to install are 3/4" male NPT connection and 4"
water column pressures natural and 10" for LP gas at the fryer
burner manifold. Supply pressure to fryers must be 7” (natural
gas) and 11” (LP) water column.
Special Order Options may include battery, common manifold,
rear drain, casters, cover, thermostat seals, portable filter, central
filter (CF14SE), Instant-On™, full size baskets, security
package, spark ignition.
INSTANT RECOVERY®FRYER 10×11 TS GAS
Printed in U.S.A. 10x11TSg2006 12/06
Oil BTU Ship
Model No. and Description Capacity Input Height Depth Width Wt.
10×11 TS Nat Gas 26 lbs. 54,000 46 1/2"26
1/2"12
3/8" 125 lbs.
10×11 TS LP Gas 26 lbs. 50,000 46 1/2"26
1/2"12
3/8" 125 lbs.
KEATING OF CHICAGO, INC.
Toll Free 1-800-KEATING
www.keatingofchicago.com
10×11 TS GAS
