Kedacom KSCA120 Series User manual

Quick Start Guide
Face Self-Check Access System

1
During installing and using the device, please follow local electrical safety regulations strictly.
Ÿ
Please use power supply in the safe voltage range of our product. Make sure if the power supply is correct
Ÿ
before running the device.
Please transport, use and store the device within defined humidity and temperature ranges.
Ÿ
Do not expose it in damp, dusty, extremely hot or cold places or places with intense electromagnetic
Ÿ
radiation or with unstable lighting.
Keep the camera away from water or any liquid
Ÿ to avoid damage to internal components.
While shipping the camera, pack it in the factory packing or use materials with equivalent quality.
Ÿ
When shipping, storing and installing the device, try to prevent it from damages caused by pressure,
Ÿ
violentvibration and soaking.
1. Power Supply
2.Working Environment
I. Preface
II. Safety Instruction
Thank you for purchasing our product. If there is any question, please do not hesitate to contact us.
These instructions are intended to ensure that the user can use the product correctly to avoid danger or
property loss. Please read this Guide carefully before using the product, and keep it properly for future
reference. If the product cannot work normally or is damaged because the user does not follow the safety
instructions, we shall not assume any responsibility. Thanks for your cooperation.
Working Environment
DC12V±10%, Power: 25W max
-40℃~+60℃
10%~95% (non-condensing)
86kPa~106kPa
-60m~3000m
Voltage
Temp.
Humidity
Altitude
Pressure

2
3. Special Statement
The product appearance is subject to the actual device and picture in this Guide is for reference only..
Ÿ
Every effort has been made to ensure the accuracy and validity of this Guide. Any update of this Guide
Ÿ
caused by version upgrade is subject to change without notice.
This Guide is made for multiple models but it will not illustrate one by one. Please refer to it according to the
Ÿ
actual products you are using.
This device can be used after being activated through IPCSearch with a valid email address for claiming the
Ÿ
password.
To ensure the safety of device on internet, it is strongly recommended that you set a strong password which
Ÿ
is composed of at least 2 kinds of the following, digits, case-sensitive letters or specific symbols, and whose
length ranges from 8 to 16 bits. Please modify the password periodically and once every 3 months is
recommended. If the device is used in highly risky environment, suggest modifying the password monthly or
weekly. Please keep your user name and password safe.
Accessing this device to the internet is at user's own risk, including but not limited to the possible network
Ÿ
attack, hacker attack, virus infection and etc. This company will not assume any responsibility for problems
of product abnormality and information disclosure caused thereof. We shall provide technical support
relating to the products in time.
For the latest documents, please download at our website www.kedacom.com.
Ÿ

3
III. Appearance and Interface
9
10
6
5
4
2
3
12
8
13
7
11
1
No.
Name
No.
Name
1
Lens
8
4xScrew Holes (fix wall)
2
White Fill Light
9
2xStaple Bolt
3
IR Light
10
Flange Plate
4
Screen
11
Locking Screw
5
Card Reader
12
Wire Hole
6
Junction Box
13
2x Screw Holes (fix junction box)
7
Shield
14
Tamper Button
[Note]
When install with the 86 box, the “Flange Plate” should be pinched off with a plier so that the buttcock line can
be threaded out; when install without the 86 box, the “Wire Hole” should be pinched off with a plier so that the
buttcock line can be threaded out.
Components:
14

Dimensions:
Unit: mm
94.245.6
54.2
39
215
50
149.5
50
60
4×Φ5.9
46
78
4

Buttcock Line:
1
2
3
5
No.
Interface Name
Function Description
1
Network
Connect to network access devices like a switch
2
Power supply
Connect to power supply of DC12V
3
User cable group
Including alarm in /out, RS-485 serial port and etc.
Table 1 Wire Interface
Cut off terminal wires
Tag 1
Tag 3
Tag 2

6
Table 2 User Cable Group Interface
Interface
No.
Color
Port Name
Function Description
User
Cable
Group
1
Yellow
NC
Normally closed door lock port
2
Pink
COM
Door lock port
3
White
NO
Normally open door lock port
4
White Brown
SENS
Door magnetic port
5
Light Green
GND
Grounding
6
Gray
Rs485+
RS-485 serial port, to control external devices
such as third-party device
7
Purple
RS485-
8
Green
GND
Grounding
9
Blue
ALARM OUT
Alarm output port
10
White Orange
ALARM OUT
Alarm output port
11
Brown
BUT
Door-open button Port
12
White Red
GND
Grounding
13
White Purple
ALARM IN-1
Alarm input port
14
White Black
GND
Grounding
15
White Blue
ALARM IN-2
Alarm input port
16
White Yellow
GND
Grounding

IV. Wire Connection
7
Cut off the user cable group and connect to RS-485, door lock, door-open button, door magnetic, alarm device,
card reader and etc.
ALARM IN-1 White Purple
White Black
White Blue
White Yellow
Blue
White Orange
ALARM IN-2
ALARM OUT
ALARM OUT COM
GND 13
14
15
16
9
10
GND
NC 1
4
5
11
12
2
3
Yellow
Pink
White
White Brown
Brown
White Red
Light Green
NO
COM
SENS
GND
GND
BUT
RS485+ Gray
6
7
8
Purple
Green
RS485-
GND
Door Lock
Power Input DC12V-
DC12V+ DC12V+
DC12V+Power
Black
Red
NC
Door
Lock
NO
Door
Lock
(NC)
Power
(NO)
Door Magnetic
Door Open Button
RS485
Door
Magnetic
Alarm Input
Alarm Output
Power Switch
Power
Alarm Input Device
Alarm Input Device
Alarm Output Device
KSCA120

8
Connect to Door Lock
The device supports NO type and NC type locks, whose connection methods are different. Please refer to the
following:
NO Magnetic Lock
System with Access Controller
NC Magnetic Lock
NO
+
+
-
-
COM
NC
NC Magnetic Lock
DC Power Adapter
Access Control
Relay Output
NO
++
+
-
-
Access Controller
COM
NC
NC Magnetic Lock
Access Control
Relay Output
NO
+
+
-
-
COM
NC
NO Magnetic Lock
DC Power Adapter
Access Control
Relay Output