IDTECK Star 100R User manual
Table of Contents
ii
Table of Contents
1 Safety Information
1 IMPORTANT SAFETY INSTRUCTIONS
2 General
3 Features
4 Specification
5 Front Panel Description
6 Identifying Supplied Parts
7 Installation
8 Wiring Color Table
9 System Wiring for Typical Application
1 Power Connection
2 Door Lock Connection
Connection of POWER FAIL SAFE: Door Lock
Connection of POWER FAIL SECURE: Door Lock
3 Alarm Device Connection
4 Exit Button Connection
5 Door Contact Sensor Connection
6 Auxiliary Input Device Connection (Applied to AUX Input #1, #2, #3)
7 Auto-Dialer Connection (Separate purchase required)
8 Wiegand Input Connection from Another Compatible Wiegand Reader (Separate purcha
se required)
9 RS-232 Communication Port Connection
...................................................... ii
................................................... 1
......................................... 3
........................................................... 4
........................................................... 5
....................................................... 6
............................................... 8
............................................. 9
......................................................... 10
................................................... 12
.................................... 15
....................................................... 15
.................................................... 16
.................................. 16
............................... 16
.................................................. 16
................................................... 16
............................................ 17
................ 17
............................ 17
............................................................... 18
..................................... 18
p.iii
10 Chime Bell Connection (Separate purchase required)
10 Initial Setup
1 Registration of RF Cards for RF CARD ONLY MODE
2 Registration of RF Cards with PINs for RF CARD + PIN MODE
3 Registration of PIN ONLY MODE
4 Registration of RF/PIN Combination MODE
5 Factory Defaulted Setting Values
11 Operation
1 Normal Operation Mode (Safe Mode)
2 Open the Door
3 Exit (Open the Door)
4 Action and Alarm Caused by Unregistered Card (or PIN)
5 Secure Mode
6 DURESS Alarm
7 Chime Bell Operation
12 Setting Changes
1 11. Add User Access Cards (RF CARD ONLY MODE)
2 12. Add User Access Cards (RF CARD + PIN MODE)
3 13. Add User Access PIN (PIN ONLY MODE)
4 14.1. Delete User Access Cards (RF CARD ONLY MODE & RF CARD + PIN MODE)
5 14.2. Delete User Access PIN (PIN ONLY MODE)
6 15. Add User Access Card/PIN (RF/PIN Combination Mode)
7 21. Change Door Open Time When User Access Card (or PIN) Is Granted
8 22. Change Alarm Time When User Access Card (or PIN) Is Denied
9 23. Change Alarm Time When Try-Out Error Detected
10 24. Change Alarm Time When Door Contact Error Detected
11 25. Change Alarm Time When AUX Input #1 Detected
12 26. Change Alarm Time When AUX Input #2 Detected
13 27. Change Alarm Time When AUX Input #3 Detected
14 28. Register 2 Digit Duress Alarm Password
15 29. Change Alarm Time When Duress Alarm Detected
16 30. Test Door Open Time Set by Command "21"
17 31. Test Alarm Time Set By Command "22"
18 32. Test Alarm Time Set By Command "23"
19 33. Test Alarm Time Set By Command "24"
........................... 18
...................................................... 19
.............................. 19
...................... 20
............................................ 20
.................................... 21
............................................ 22
........................................................ 24
........................................ 24
.......................................................... 24
..................................................... 25
.......................... 25
........................................................... 25
.......................................................... 26
..................................................... 26
................................................... 27
............................. 31
............................. 32
................................... 32
...... 32
................................ 33
....................... 33
............ 34
................. 34
........................... 35
..................... 35
.......................... 35
.......................... 36
.......................... 36
.................................. 36
.......................... 37
............................... 37
................................... 37
................................... 37
................................... 37
Table of Contentsp.iv
20 34. Test Alarm Time Set By Command "25"
21 35. Test Alarm Time Set By Command "26"
22 36. Test Alarm Time Set By Command "27"
23 37. Change Chime Bell Activating Time
24 38. Open Door Unconditional
25 39. Close Door Unconditional
26 40. Enable QUICK ACCESS MODE
27 41. Disable QUICK ACCESS MODE
28 42. Enable Toggle Mode for Lock Control
29 43. Disable Toggle Mode for Lock Control
30 44. Enable Lock followed by Door Contact
31 45. Disable Lock followed by Door Contact
32 46. Disable Melody Sound
33 47. Enable Melody Sound
34 48. Change Keypad Lock-out Time When Try-Out Error Detected
35 49. Set AUX Input #1 Detection from ‘L’ to ‘H’
36 50. Set AUX Input #1 Detection from ‘H’ to ‘L’
37 Set AUX#2 Input Detection from ‘H’ to ‘L’
38 53. Set AUX#3 Input Detection from ‘L’ to ‘H’
39 54. Set AUX#3 Input Detection from ‘H’ to ‘L’
40 55. Set Exit Button Input Detection from ‘L’ to ‘H’
41 56. Set Exit Button Input Detection from ‘H’ to ‘L’
42 57. Set Door Contact Sensor Input Detection from ‘L’ to ‘H’
43 58. Set Door Contact Sensor Input Detection from ‘H’ to ‘L’
44 59. Activate TTL Output to ‘H’
45 60. Activate TTL Output to ‘L’
46 61. Enable Keypad Input To Enter ID Number
47 62. Disable Keypad Input To Enter ID Number
48 63. Enable Chime Bell Output
49 64. Disable Chime Bell Output
50 65. Set Delay Time to Activate SECURE MODE
51 66. Set Door Open Time-out for Door Contact Sensor
52 67. Set Number of Times of Try-Out
53 68. Set Input Keypress Time-out Time
54 69. Set Tamper Alarm Output Port
55 70. Enable Tamper Alarm
................................... 37
................................... 38
................................... 38
...................................... 38
............................................. 38
............................................. 39
.......................................... 39
.......................................... 39
.................................... 39
.................................... 40
................................... 40
................................... 40
................................................ 41
................................................ 41
.................. 41
................................. 41
................................. 42
.................................... 42
................................. 42
................................. 42
.............................. 43
.............................. 43
....................... 43
....................... 43
............................................. 44
.............................................. 44
................................. 44
................................. 44
............................................. 45
............................................. 45
................................ 45
........................... 45
........................................ 46
....................................... 46
......................................... 46
................................................. 47
p.v
56 71. Disable Tamper Alarm
57 72. Re-Initialize and Erase All Setup Data
13 Initialization
1 Hardware Initialization (When the master card or ID is lost)
2 Wire Initialization
2.1 100R: Over V5.0.4 / IP100R: Over V2.0.2
2.2 100R: V5.0.0 ~ V5.0.3 / IP100R: V2.0.0 ~ V2.0.1
14 FCC REGISTRATION INFORMATION
15 Troubleshooting
1 [Operation]
1.1 Problem
Cause
Solution
1.2 Problem
Cause
Solution
2 [Registering or Deletion]
2.1 Problem
Cause
Solution
2.2 Problem
Cause
Solution
Having a master card or PIN
Loosing a master card or PIN
3 [System Initialization]
3.1 Problem
Cause
Solution
100R V5.0.0 under or IP100R V2.0.0 under
100R V5.0.0 over or IP100R V2.0.0 over
4 [Communication]
4.1 Problem
Cause
Solution
................................................ 47
..................................... 47
...................................................... 48
....................... 48
........................................................ 49
................................... 49
............................. 49
.................................... 50
................................................... 51
............................................................. 51
............................................................. 51
................................................................ 51
............................................................... 51
............................................................. 52
................................................................ 52
............................................................... 52
.................................................. 53
............................................................. 53
................................................................ 53
............................................................... 53
............................................................. 54
................................................................ 54
............................................................... 54
............................................. 54
............................................. 55
..................................................... 55
............................................................. 55
................................................................ 55
............................................................... 55
................................. 55
.................................... 56
........................................................ 56
............................................................. 56
................................................................ 56
............................................................... 57
Table of Contentsp.vi
5 [Keypad]
5.1 Problem
Cause
Solution
6 [External Device]
6.1 Problem
Cause
Solution
6.2 Problem
Cause
Solution
6.3 Problem
Cause
Solution
16 Template
17 RMA Request
............................................................... 57
............................................................. 57
................................................................ 57
............................................................... 58
........................................................ 58
............................................................. 58
................................................................ 58
............................................................... 59
............................................................. 60
................................................................ 60
............................................................... 60
............................................................. 61
................................................................ 61
............................................................... 62
......................................................... 64
..................................................... 65
Safety Information 1
p.1
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIE
D SERVICE PERSONNEL.
This symbol indicates that dangerous voltage consisting a risk of electric shock is pres
ent within this unit.
This exclamation point symbol is intended to alert the user to the presence of importa
nt operating and maintenance (servicing) instructions in the literature accompanying the ap
pliance.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
WARNING
1. Be sure to use only the standard adapter that is specified in the specification sheet. Usin
g any other adapter could cause fire, electrical shock, or damage to the product.
2. Incorrectly connecting the power supply or replacing battery may cause explosion, fire,
electric shock, or damage to the product.
Safety Informationp.2
3. Do not connect multiple controllers to a single adapter. Exceeding the capacity may cau
se abnormal heat generation or fire.
4. Securely plug the power cord into the power receptacle. Insecure connection may caus
e fire.
5. When installing the controller, fasten it securely and firmly. The fall of controller may ca
use personal injury.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or container
s filled with water on top of the controller. Doing so may cause personal injury due to fi
re, electric shock, or falling objects.
7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or el
ectric shock.
8. If any unusual smells or smoke come from the unit, stop using the product. In such case,
immediately disconnect the power source and contact the service center. Continued us
e in such a condition may cause fire or electric shock.
9. If this product fails to operate normally, contact the nearest service center. Never disass
emble or modify this product in any way. (SAMSUNG is not liable for problems caused
by unauthorized modifications or attempted repair.)
10. When cleaning, do not spray water directly onto parts of the product. Doing so may ca
use fire or electric shock.
CAUTION
1. Do not drop objects on the product or apply strong blows to it. Keep away from a locat
ion subject to excessive vibration or magnetic interference.
2. Do not install in a location subject to high temperature (over 50°C), low temperature (b
elow -30°C), or high humidity. Doing so may cause fire or electric shock.
3. If you want to relocate the already installed product, be sure to turn off the power and
then move or reinstall it.
4. Remove the power plug from the outlet when there is a lighting storm. Neglecting to d
o so may cause fire or damage to the product.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire.
6. Install it in a place with good ventilation.
7. Avoid aiming the controller directly towards extremely bright objects such as sun.
8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liqui
ds, such as vases, shall be placed on the apparatus.
9. The Mains plug is used as a disconnect device and shall stay readily operable at any tim
e.
p.3IMPORTANT SAFETY INSTRUCTIONS
1IMPORTANT SAFETY INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturer’s ins
tructions.
8. Do not install near any heat sources such as radiators, heat registers, or other apparatus
(including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized
plug has two blades with one wider than the other. A grounding type plug has two bla
des and a third grounding prong. The wide blade or the third prong is provided for you
r safety. If the provided plug does not fit into your outlet, consult an electrician for repla
cement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenie
nce receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with cart, stand, tripod, bracket, or table specified by the manufacturer, or sol
d with the apparatus.
13. Unplug this apparatus when a card is used. Use caution when moving the cart/ apparat
us combination to avoid injury from tip-over.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparat
us has been damaged in any way, such as power supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus, the apparatus has been expo
sed to rain or moisture, does not operate normally, or has been dropped.
General 2
p.4
A properly configured Star 100R / iPASS IP100R is an intelligent PIN & Proximity and PINPAD
Single Door Controller that combines the convenience of wireless entry with the security of
an alarm system. Also, the Star 100R / iPASS IP100R system will give you field proven reliabil
ity and cost-effective solution anywhere access controls and high security are required. Each
standard unit can store up to 512 users or card IDs. The task of assigning cards and managin
g a user’s database is so simple, user friendly, and can be accomplished in many ways; it coul
d be as simple as presenting each card to the unit or as descriptive as a user’s database with
an easy to use Graphical User Interface.
The Star 100R / iPASS IP100R can interface and operate with these accessories: Request for
EXIT button, Door-Contact sensor, PIR sensor, Fire sensor and other sensors via 5 independe
nt input ports. Also, output ports which include 2 Relays and 2 TTL outputs can be used to c
ontrol the operation of other accessories such as Electric/Magnetic Door Lock, Alarm, Chime
Bell, and Auto-Dialer. Moreover, the status or behaviors of these input and output accessori
es are configurable to provide the system administrator with complete customized control o
f the system. Besides the above configurable I/O interfaced behaviors, many of the Star 100
R / iPASS IP100R internal behaviors are programmable as well. The internal operating param
eters include the number of incorrect access attempts before alarm condition is triggered, ta
mpering protection from mounting removal, and timers. Furthermore, every event or transa
ction can be captured in real time by the Star 100R / iPASS IP100R application software (ST
AR 100R PRO) using the provided
Features 3
p.5
●125KHz Standalone Proximity /PIN Single Door Access Controller
●100R: PSK Modulation / IP100R: ASK [EM] Format
●Basic Time & Attendance Function
●512 Users including One Master Card
●1 External Reader Port for Exit: 26bit Wiegand
●Standalone / Network Communication via RS232
●All I/Os and Operation Time Programmable by Keypad
●Independent 5 Inputs and 4 Outputs Including 2 Form-C Relay Outputs
●Keypad Lock by Try-out Error Alarm Function
●Duress Mode Function
●Toggle Mode for Door Opening / Closing
●Lock Control by Door Contact Switch
●Safe (Default) / Secure Mode Available
●Dual Tamper Switches
●Chime Bell Output
●Mode Selection: RF Only / PIN (4~6 digit) Only / RF+ P/W (4 digit) / RF or PIN
●Options: 4ch Voice Auto-dialer
●Compatible Software: STAR 100R PRO
Comparison Table
100R 125KHz PSK Modulation
IP100R 125KHz ASK[EM] Format
Specification 4
p.6
Model 100R IP100R
CPU Dual 8bit Microprocessor
Memory Program Memory 20KByte ROM
Data Memory 2KByte EEPROM
User 512 Users
Read Range IDC80 / IDC170:
Up to 4 inches (10cm)
IPC80 / IPC170:
Up to 4 inches (10cm)
Reading Time (Card) 30ms
Power / Current DC 12V / Max.200mA
External Reader Port 1ea (26bit Wiegand)
Communication RS232
Input Port 5 Ports
(Exit Button, Door Contact, Aux #1, Aux #2, Aux
#3)
Output Port 2 Ports (Form-C Relay Output (COM, NO, NC) / D
C12~18V, Rating Max.2A)
1 Port (Chime Bell Output / DC5V, Rating Max. 5
00mA)
1 Port (TTL Output / DC5V, Rating Max.20mA)
Keypad 12 Key Numeric Keypad with Back Lighting
LED Indicator 3 Array LED Indicators (Red, Green and Yellow)
Beeper Piezo Buzzer
Operating Temperature -35 to +65 C ( -31 to +149 F )
Operating Humidity 10% to 90% Relative Humidity Non-condensing
p.7
Color / Material Dark Pearl Gray / Polycarbonate
Dimension (W x H x T) 87mm x 100mm x 31mm (3.4" x 3.94" x 1.22")
Weight 210g (0.46lbs)
Certification FCC, CE, KC, RoHS
Model 100R IP100R
Front Panel Description 5
p.8
Identifying Supplied Parts 6
p.9
Please unpack and check the contents of the box.
Installation 7
p.10
1. Tear off page template in the back of this manual and use the provided template to drill
two 6-32 holes and one 1/2" hole on the proper location of the wall to mount the Wall
Mount bracket as shown below.
(If the gang box is already installed on the wall then skip this step.)
2. Using 2 screws, install wall mount to the wall.
p.11
Before mounting the STAR 100R unit to the Wall Mount bracket, operational testi
ng of the unit should be completed, as the locking pins will lock the unit to the Wa
ll Mount. Removing the unit from the Wall Mount bracket after they have been ins
talled together may cause damages to the bracket and render its effectiveness.
3. Insert 5 O-rings to the wall mount as indicated, then route the cable of the main unit th
rough the center hole and push the main unit to wall mount to lock the main unit and
make sure that the main unit is locked with wall mount.
Wiring Color Table 8
p.12
I/O PORT NAME SIGNAL NAME COLOR CODED
2PIN (J1)
Main Power(+12V) DC +12V Red
Power Ground GND Black
10PIN (J2)
Door Relay(NC) NC(1) Blue with White Stripe
Door Relay(COM) COM(1) Gray with Red Stripe
Door Relay(NO) NO(1) White with Red Stripe
Alarm Relay(NC) NC(2) Purple with White Stripe
Alarm Relay(COM) COM(2) White
Alarm Relay(NO) NO(2) Purple
Exit Button EXIT Orange
Door Sensor CONTACT Yellow with Red Stripe
Aux Input 1 INPUT1 Green
Aux Input 2 INPUT2 Green with White Stripe
7PIN (J3)
Wiegand Data0 DATA0 Pink
Wiegand Data1 DATA1 Cyan
TTL Output TTL1/D0 Orange with White
Chime Bell Output CHI/D1 Brown with white Stripe
Aux Input 3 INPUT3 Green with Red Stripe
p.13
RESERVED Blue with Red Stripe
RESERVED Yellow with White Stripe
3PIN (CON2)
RS232-TX TXD Black with White Stripe
RS232-RX RXD Red with White Stripe
Ground GND Black
I/O PORT NAME SIGNAL NAME COLOR CODED
Optional: Wiegand Output Function
The default output format of 100R/IP100R is TTL and Chime Bell output. But, you can config
ure the 100R/IP100R to generate output in Wiegand format and use it like a reader.
(The 100R/IP100R can output data from card reading, but can’t output data from keypad in
put.)
If you want to generate Wiegand instead of TTL output format, follow the table below.
This function is only applicable to :
V6.0.0 of the 100R and higher
V3.0.0 of the IP100R and higher
SW1 #1 SW1 #2 SW2 #1 SW2 #2 Orange wire with White stri
pe
Brown wire with White stri
pe
ON OFF ON OFF TTL Output Chime Bell Output
OFF ON OFF ON Wiegand Data 0 Output Wiegand Data 1 Output
Wiring Color Tablep.14
When the Wiegand Output function is used, TTL Output wire is changed to Wiega
nd Data 0 and Chime Bell Output wire to Wiegand Data 1 Output wire. Therefore,
you can’t use those functions. In addition, because TTL Output wire is changed to
Wiegand Data 0 Output, you can’t initialize the 100W/IP100W using the wires.
(You can use those functions again when setting SW1 and SW2 to the default stat
e.)
Other manuals for Star 100R
3
This manual suits for next models
1
Table of contents
Other IDTECK IP Access Controllers manuals
IDTECK
IDTECK Star LX505 User manual
IDTECK
IDTECK Star FINGER006 User manual
IDTECK
IDTECK Star FINGER006 User manual
IDTECK
IDTECK FINGER007 Series User manual
IDTECK
IDTECK LX007 User manual
IDTECK
IDTECK Star LX505 User manual
IDTECK
IDTECK Star Finger007 User manual
IDTECK
IDTECK Star iCON100 User manual
IDTECK
IDTECK Star LX505 User manual
IDTECK
IDTECK iTDC EIO8 User manual
IDTECK
IDTECK Star 505R User manual
IDTECK
IDTECK Star iCON100 User manual
IDTECK
IDTECK Star Finger007 User manual
IDTECK
IDTECK Star 505R User manual
IDTECK
IDTECK iTDC Operating instructions
IDTECK
IDTECK Star 505R User manual
IDTECK
IDTECK iPass IP-RFL200 User manual
IDTECK
IDTECK ITDC ITDCSR EIO88 User manual
IDTECK
IDTECK GE313 User manual
IDTECK
IDTECK Star iCON100SR User manual
