KEENCUT Evolution3 SmartFold User manual

SmartFold Bench
The world’s finest cutting machines
Assembly manual
www.keencut.com
[email protected]
[phone]
SFB280920

Start
Page 3
1
Without cantilever
Page 8
2
3
With cantilever
Page 22
4
Finish
Page 40

Start
1

4
Section
Components
A
B
C
D
E
F
G
H
I
J
K
L
M
N
1
Part Description
Part quantities based on bench model
SFB110 SFB160 SFB210 SFB260 SFB310 SFB360 SFB410 SFB460 SFB510
Quantity Quantity Quantity Quantity Quantity Quantity Quantity Quantity Quantity
ABench edge 1 x 1320mm /
52”
2 x 890mm /
35 ¹⁄₁₆”
2 x 1140mm /
44 ⅞”
2 x 1390mm /
54 ¾”
3 x 1080mm /
42 ½”
3 x 1247mm /
49 ¹⁄₁₆”
3 x 1413mm /
55 ⅝”
4 x 1175mm /
46 ¼”
4 x 1300mm /
5 ³⁄₁₆”
BBeam1 3 x 1320mm /
52”
6 x 890mm /
35 ¹⁄₁₆”
6 x 1140mm /
44 ⅞”
6 x 1390mm /
54 ¾”
9 x 1080mm /
42 ½”
9 x 1247mm /
49 ¹⁄₁₆”
9 x 1413mm /
55 ⅝”
12 x 1175mm /
46 ¼”
12 x 1300mm /
5 ³⁄₁₆”
CBeam2 (1247mm / 49 ¹⁄₁₆”) 46668881010
DLeg 46668881010
ECantilever arm 233344455
FCantilever joiner 233344455
GLeft support plate 111111111
HRight support plate 111111111
IIntermediate support plate 011122233
JCorner bracket 20 34 34 34 48 48 48 62 62
KGrub screw 60 102 102 102 144 144 144 186 186
LWorktop fixing bracket 6 11 11 11 16 16 16 21 21
MWorktop fixing screw 6 11 11 11 16 16 16 21 21
NAdjustable foot 46668881010

5
Section
Tools included Tools not included
4mm
4mm
13mm
13mm
4mm
4mm
1
Spacer

6
Section
+
+
To prevent injury and damage, lift the boxes with 2 people.
Be careful with lifting 1

7
Section
1.5m (5’)
1.2m (4’)
1
With cantilever
Without cantilever
Page 22
Page 8
3
2

Without cantilever
2

9
Section
4mm
x3
x1
J
K
1.
2.
Prepare the brackets
1. Insert a grub screw backwards into the bracket and screw
into place until only 2 threads are showing.
2. Insert two grub screws in from the flat face of the bracket 2
turns only.
IMPORTANT: Make the brackets for your bench using all J and K parts
supplied.
2

10
Section
4mm
1. 2.
1. Slide a corner bracket into position and place the spacer over it. Hold the spacer so it is flush with the top of
the leg. Use a straight edge to ensure that the spacer is flush with the end of the leg.
2. Initially tighten gently with the long end of the Allen key. Then remove the spacer and fully tighten with a
further 2-3 half turns using the short end of the Allen key.
IMPORTANT: These steps are essential to ensure the finished bench is rigid. The spacers must be aligned
precisely, and be flush with the ends of the leg. The screws must be tightened fully.
How to fit the brackets 2