KeepGuard KG375 User manual

This KeepGuard cam is the best-selling scouting camera which is designed for activity and is resistant against water and snow. It is
equipped with built-in infrared LEDs, so that it can be triggered by any movement in a location, then take high quality pictures or
video clips. Please refer to the notes below and instructions in this manual to ensure that you are completely satisfied with this
product.
KEEPTIME
Applicable models：KG375
Contents
Highly Recommended by Outdoor Explorers - KeepGuard Wildlife Scouting Cam KG Cams Instruction Book
1
Quick Start 2
Notes before use 3
View Drawings 4
Camera Overview 5
Standard Accessories 6
Power Supply 7
SD Card 7
Operational Modes 8
Settings 9~11
Mounting and Positioning 12
Specification 13
Warranty Card 14

Move the latches and open the front cover
Load 4 lithium AA or alkaline AA batteries
Insert the SD card
Switch to the“On”
Connect your Keepguard camera to the “KEEP GUARD”App with Bluetooth to do setting.
Put it good position
Switch to the ON Mode and it have started working
How to use App , you can reference Keep Guard App “quick start”
(Download using Apple store or Google play)
2
KEEPTIME
Quick Start

1. When setting camera parameters, please put camera in ON mode , open Keep Guard App and connect your camera.
2. When you connect camera and app,your can change settings.
3. To replace the battery, SD card,firstly turn camera to OFF mode.
4. Color of Indicator
1) When camera is updating, indicator light flashes green.
2) The indicator light flashes red 5 times continous ,when it is turned on and don’t connect app.
5. Batteries need to use dry batteries, can not use rechargeable batteries.
6. When the SD card is inserted into camera, make sure that the SD card is not in the unprotected state.
7. When using an external power supply, make sure that voltage is correct.
8. Please take out the battery for long time unused, so as to avoid leakage of the battery time is too long.
9. Camera can not be directly immersed in water, can not be placed in the environment of strong acid and alkali.
10. Finger can not press the Fresnel lens.
11. Keep the lens and battery compartment clean.
12. Do not use sharp hard objects to attack the screen and so on.
3
KEEPTIME
Notes Before Use

View Drawings
4
KEEPTIME

5
Camera Overview
KEEPTIME 5

1× Security Case 1×Solar panel Micro-Lens / Wide-angel Lens 1×Cradle Head
KEEPTIME
Standard Accessories
1×Belt 1×USB 1×Case 1×Manual
6
Other Accessories (not included)

After opening the latch on the right side of the camera, you
will see that it has 4 battery slots. For maximum battery life,
we recommend using 4 lithium AA or alkaline AA batteries.
Please be sure to insert each battery with correct polarity
(negative or“flat”end against the long spring of each battery
slot).
When you use extral DC , you must use dc 6V/1A or over 1A
power adapater. We recommend using 6V/2A.
Insert the SD card ( OFF mode ) before beginning to operate the
camera. SD card is supported up to maximum 64GB capacity.
7
KEEPTIME
Power Supply
SD Card

●「APP SETUP」Mode
In the ON mode and you connect the camera by APP. You can check and change the settings of the cam with APP. When you
connect the camera by APP , you will see the current settings information .
The cam has three basic operational modes: 「OFF」, 「ON」and 「APP SETUP」
●「OFF 」Mode
When cam in OFF mode, you can do the following:
• replacing the SD card or batteries
• connecting cam with other device by USB port
It will occur a little of power consumption under OFF mode. If you won't use it for a long time, please take batteries off.
●「ON」Mode
Once in ON mode no manual controls are needed or possible (the control keys have no effect). The cam will take photos or videos
automatically (according to its current parameter settings) when it is triggered by the PIR sensor′s detection of activity in the area it covers.
KEEPTIME 8
Operational Modes

9
Keep Guard App quick start
In the ON mode and you connect the camera by APP. You can check and change the settings of the cam with APP. When
you connect the camera by APP , you will see the current settings information .
Connecting Camera(s):
1. Make sure batteries and Micro SD Card are installed correctly within camera.
2. Open Control Panel, ‘Turn On’ Camera and close control panel.
3. Make sure ‘Bluetooth’ in your phone/tablet settings is “turned on”
4. Open Keep Guard APP
5. Press ‘+’ to find camera.
6. Press ‘ADD CAMERA’ to find device
5. Camera(s) will pop up by defaulted name, click Connect on right side
of screen.

10
Settings
Camera Name：
Allows the user to set a custom name for the camera. Useful for ID purposes when
multiple cameras are setup, since each camera will imprint its name on all photos
(but not videos) it captures.
Mode:
Selects whether still photos or video clips are captured when the camera is
triggered.
Image Size：
Selects resolution for still photos from 3 to 16 megapixels. Higher resolution
produces better quality photos, but creates larger files that take up more of the SD
card capacity.
Capture Number：
Selects how many photos are taken in sequence per trigger in Camera mode. This
setting affects photos taken in Field Scan mode as well.
Delay Interval：
Selects the length of time that the camera will “wait”until it responds to any
additional triggers from the PIR after an animal is first detected and remains within
the sensor's range. During this user set“ignore triggers”interval, the camera will
not capture photos/videos.This prevents the card from filling up with too many
redundant images.
Date and Time:
The date and time is set automatically