Kenmore 318201435 User manual

INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE FOR LOCAL ELECTRICAL INSPECTOR'S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
FOR YOUR SAFETY: Do not store or use gasoline or other flammable vapors and liquids in the
vicinity of this or any other appliance.
Cooktop Dimensions
30" Min. *
Air Exhaust(76"2 cm) A
IMPORTANT INSTALLATIONINFORMATION
• All electric cooktops run off a single phase, three-wire or four-
wire cable, 240/208 volt, 60 hertz, AC only electrical supply
with ground.
• Pleasenote minimum distance between cooktop and adjacent
and overhead unprotected cabinetry is 30" (76.2 cm).
* 30" (76.2 cm) min. for unprotected cabinet
24" (61 cm) min. for protected surface
_The corners of this unit are
fragile. Carefully install the cooktop by its
sides. When installing, never let the weight
of the unit rest on any one corner.
Cooktop Cutout Dimensions
Fresh Air Intake
-------- 4" X 8" (10.2 cm x 20.3 cm)
opening at the right rear
to route armored cable
if a panel is present
Figure 1 -30" Model shown only
MODEL A.WIDTH B.DEPTH C.HEIGHT D BOXWIDTH E BOXDEPTH
30"CeramicModel 303A(78.1) 211/2(54.6) 2V4(5.1) 29 (73.7) 193/8(49.2)
36"CeramicModel 363A(93.3) 21Y2(54.6) 2Y4(5.1) 35(88.9) 193/8(49.2)
MODEL MINIMUM MAXIMUM MINIMUM MAXIMUM COOKTOF
30" CeramicModel 29%(75.2) 30 (76.2) 201/4(51.4) 20V2(52.1) 6 (15.2)
36" CeramicModel 35%(90.5) 36 (91.4) 201/4(51.4) 20V2(52.1) 6 (15.2)
All dimensions are in inches (cm).
* Allow 2" (5 cm) space below cooktop to clear the electric cable and allow for
installation of the junction box on the wall at the back of the cooktop.
Printedin United States
P/N 318201435 (0706) Rev.
English - pages 1-6
Espa¢_ol- pages 7-12

Overhead Cabinet Should Not Exceed
a Maximum Depth of 13" (33 cm)
A Min.
30" (76.2 cm) Min.
Clearance Between the
Top of the Cooking
Platform and the Bottom
of an Unprotected Wood
or Metal Cabinet _i
31
24" (61 cm)Mi_
Bottom of Wood or Metal
Cabinet isProtected by
Not LessThan 1/8" Flame
Retardant Millboard
Covered With Not Less
Than No. 28 MGS Sheet
Steel, 0.015" (0.4 mm)
Stainless Steel, 0.024"
(0.6 mm) Aluminum or
0.020" (0.5 mm) Copper
18"
(45.7 cm)
2" (5.1 cm)Min.
Recommended
Distance Between
RearEdge of Cutout
and Nearest 10"
Combustible Surface ( 25.4 cm)
Above Countertop
J
G
2 1/2" (6.4 cm) Min. rom
Edge of Cutout to Front Edge
of Countertop
Approximate Location
of Junction Box
7V2" (19.1 cm)
Min. From Edge
of Cooktop to
Nearest
Combustible
Wall (Either
Side of Unit).
It is not recommended to use
drawer underneath cooktop.
Empty space isneeded for
installation purpose.
Letterson this figure refer to chart on front page.
_To eliminate the risk of burns
or fire by reaching over heated surfaces,
cabinet storage space located above the
cooktop should be avoided. If cabinet
storage is provided, risk can be reduced by
installing a range hood that projects
horizontally a minimum of 5" (12.7 cm)
beyond the bottom of the cabinets.
Figure 2 -COUNTERTOP CUTOUT OPENING

Important Notes to the Installer
1. Readall instructions contained in these installation
instructions before installing the cooktop.
2. Remove all packing material before connecting the
electrical supply to the cooktop.
3. Observe all governing codes and ordinances.
4. Be sure to leavethese instructions with the consumer.
Important Note to the Consumer
Keep these instructions with your Use and Care Guide for
future reference.
IMPORTANT SAFETY
INSTRUCTIONS
• Be sure your cooktop is installed and grounded
properly by a qualified installer or service
technician.
• These cooktops must be electrically grounded in
accordance with local codes or, in their absence,
with the National Electrical Code ANSI/NFPA No.
70--latest edition in the United States, or with
CSA Standard C22.1, Canadian Electrical Code, Part
1, in Canada.
IF!,,_,l,_l=t_ll_[_The electrical power to the cooktop
must be shut off while line connections are being
made. Failure to do so could result in serious injury
or death.
Provide Electrical Connection
Install the junction box under the cabinet and run 120/
240 or 120/208 Volt, AC wire from the main circuit
panel. DO NOT connect the wire to the circuit panel at
this time.
Electrical Requirements
This appliance must be supplied with the proper voltage
and frequency, and connected to an individual, properly
grounded branch circuit, protected by a circuit breaker or
fuse. To know the circuit breaker or fuse recommended
for your model, see the serial plate to find the wattage
consumption and refer to table A to get the circuit
breaker or fuse amperage.
ApplianceRating Protection ApplianceRating Protection
Watts Circuit Watts Circuit
240V recommended 208V recommended
lessthan4800W 20A Lessthan 4100W 20A
4800W - 7200W 30A 4100W - 6200W 30A
7200W- 9600W 40A 6200W- 8300W 40A
9600Wand + 50A 8300W and+ 50A
Table A
Observe all governing codes and local ordinances.
1. A 3-wire or 4-wire single phase 120/240 or 120/208
Volt, 60 Hz AC only electrical supply is required on a
separate circuit fused on both sides of the line (time-
delay fuse or circuit breaker is recommended). DO
NOT fuse neutral.
NOTE: Wire sizes and connections must conform with
the fuse size and rating of the appliance in accordance
with the National Electrical Code ANSI/NFPA No. 70-
latest edition, and local codes and ordinances.
An extension cord must not be used
with this appliance. Such use may result in a fire,
electrical shock, or other personal injury.
2. The appliance should be connected to the fused
disconnect (or circuit breaker) box through flexible
armored or nonmetallic sheathed cable. The flexible
armored cable extending from this appliance should
be connected directly to the grounded junction box.
The junction box should be located as shown in
Figure 2 with as much slack as possible remaining in
the cable between the box and the appliance, so it
can be moved if servicing is ever necessary.
3. A suitable strain relief must be provided to attach
the flexible armored cable to the junction box.
Unpacking Instructions
1. Leave corner supports on cooktop until completion
of Electrical Connection.
2. Be sure the bottle of cleaner conditioner packed in
the literature bag is left where the user can find it
easily. It is important that the ceramic-glass
smoothtop be pretreated before use. See Ceramic
Glass Cooktop Cleaning and Maintenance section
in the Use and Care Guide.
Model and Serial Plate
Figure 3 (Under Cooktop)

Electrical Connection
Connect the flexible armored cable that extends from the
surface unit to the junction box using a suitable strain
relief at the point the armored cable enters the junction
box. Then make the electrical connection as follows.
Electrical ground is required on this appliance.
This appliance is equipped with a
copper conductor flexible cable. If connection is
made to aluminum house wiring, use only special
connectors which are approved for joining copper
and aluminum wires in accordance with the National
Electrical Code and local codes and ordinances.
Improper connection of aluminum house wiring to
copper leads can result in a short circuit or fire.
Follow the connector manufacturer recommended
procedure closely.
This appliance is manufactured with a frame connected
green (or bare copper) ground wire.
DO NOT ground to a gas supply pipe.
DO NOT connect to electrical power supply until
appliance is permanently grounded. Before turning
on the power, permanently connect the ground wire
first, then complete all remaining wire connections.
Secure the cover onto the junction box.
Where local codes permit connecting the appliance-
grounding conductor to the neutral (white) wire:
If your cooktop has a 3-wire cable to be connected
to a 3-wire grounded junction box (see figure 4):
1. Disconnect the power supply.
2. In the circuit breaker, fuse box or junction box:
connect appliance and power supply cable wires as
shown in figure 4.
Cable from Power Supply
White Wire
(Neutral)
Red
Wires Black
Wires
Box
Ground Wire J.L.-Listed Conduit
(Bare or Green Wire) Connector (or CSA
listed)
Cable from appliance
Figure 4
3-WIRE GROUNDED JUNCTION BOX
If your cooktop has a 4-wire cable to be connected
to a 3-wire grounded junction box (see figure 5):
1. Disconnect the power supply.
2. In the circuit breaker, fuse box or junction box:
connect appliance and power supply cable wires as
shown in figure 5.
Cable from Power Supply
White Wire
(Neutral) Wires
Red l
Wires
Box
(Neutral)
Ground Wire U.k-Listed Conduit
Bare or Green Wire) Connector (or CSA listed)
Cable from appliance
Figure 5
3-WIRE GROUNDED JUNCTION BOX
36" Models with Warmer Zone
You may not ground the cooktop
through the neutral (white) wire if cooktop is used
in a new branch circuit installation (1996 NEC),
mobile home, recreational vehicle, or where local
codes do not permit grounding through the
neutral (white) wire. When grounding through the
neutral (white) wire is prohibited, you must use a
4-wire power supply cable. See Figure 6 & 7.
Failure to heed this warning may result in
electrocution or other serious personal injury.

If cooktop is used in a new branch circuit
installation (1996 NEC), mobile home, recreational
vehicle, or where local codes DO NOT permit
grounding through the neutral (white) wire:
If your cooktop has a 3-wire cable (see figure 6):
1. Disconnect the power supply.
2. Separate the green (or bare copper) and white
appliance cable wires.
3. Cap the white wire from the power supply cable if a
3-wire appliance cable is supplied.
4. In the circuit breaker, fuse box or junction box:
connect appliance and power supply cable wires as
shown in figure 6.
Cable from Power Supply
1 -White Wire
GroundWired J
Red :_
Wires _J_ _]-"__ _ Black
__ _on Box
Ground Wire /_ _ U.L.-Listed Conduit
(Bare or Green Wire) _ Connector (or CSA
listed)
Cable from appliance
Figure 6
4-WIRE GROUNDED JUNCTION BOX
If your cooktop has a 4 wire cable (see figure 7):
1. Disconnect the power supply.
2. Separate the green (or bare copper) and white
appliance cable wires.
3. In the circuit breaker, fuse box or junction box:
connect appliance and power supply cable wires as
shown in figure 7.
Cable from Power Supply
Ground Wire
Red
Ground Wire
(Bare or
Wire)
Wires 1
Black
Conduit
Junction Box Connector (or CSA listed)
Cable from appliance
Figure 7
Models 36" with Warmer Zone
4-WIRE GROUNDED JUNCTION BOX
_!,VAVl-'l:l_ll_[ellIf connecting to a4-wire power supply
cable electrical system, the appliance frame
connected ground wire MUST NOT be connected to
the neutral wire of the 4-wire electrical system.

Cooktop Installation
1. Visually inspect the cooktop for damage. Also make
sure all cooktop screws are tight (see Figure 8).
Screws
Figure 8
2. Install the retainer brackets (See Figure 9).
The retainer brackets MUST be installed, to meet
local codes or, in their absence, with the National
Electrical Code ANSI/NFPA No. 70--latest edition, or
with CSA Standard C22.1, Canadian Electrical Code,
Part 1 (see Figure 9).
Cookto Countertop
8-18 x3/8
3. Set the cooktop into the countertop cutout.
NOTE: Do not use caulking compound; cooktop should
be removable for service when needed.
lf!,.iVl:l;|_ll_[ell Do not remove the nylon spacers on
the edges of the cooktop. These spacers center the
cooktop in the space provided. The cooktop must
be centered to prevent excess heat buildup that
may result in heat damage or fire (see Figure 10).
2 Nylon 7 9/16"
/
/.
2 Retainer _ ........
brackets _, ......... Figure 10
The corners of this unit are fragile.
Carefully install the cooktop by its sides. When
installing, never let the weight of the unit
rest on any one corner.
Checking Operation
Refer to the Use and Care Guide for operation.
_Do not touch cooktop glass or elements.
They may be hot enough to burn you.
Model and Serial Number Location
The serial plate is located under the cooktop.
When ordering parts for or making inquiries about your
cooktop, always be sure to include the model and serial
numbers and a lot number or letter from the serial plate
on your cooktop.
Before You Call for Service
Read the Before You Call for Service Checklist and
operating instructions in your Use and Care Guide. It
may save you time and expense. The list includes
common occurrences that are not the result of defective
workmanship or materials in this appliance.
Refer to your Use and Care Guide for Sears service
phone numbers, or call 1-800-4-MY-HOME ®.

LA INSTALACION Y EL SERVICIO DEBEN SER EFECTUADOS POR UN INSTALADOR CALIFICADO.
IMPORTANTE: GUARDE ESTAS INSTRUCCIONES PARA USO DEL INSPECTOR LOCAL DE ELECTRICIDAD.
LEA Y GUARDE ESTAS INSTRUCCIONES PARA REFERENCIA FUTURA.
PARA SU SEGURIDAD: No almanece ni utilice gasolina u otros vapores y liquidos inflamables
en la proximidad de este o de cualquier otto artefacto.
Dimensiones de la Estufa
Salidade 30" Min. *
Aire (76.2 cm)
C
Dimensiones del
Recortado de la Estufa
A
Entrada de Aire
INFORMACION IMPORTANTE PARALA INSTALACION
•Todas las estufas electricas funcionan con una
alimentaciOn electrica con puesta a tierra de fase singu-
lar,3 o 4 alambres, 240/208 voltios, 60 hertz y sOloAC.
• Favorde notar que ladistancia minima entre la superficie
de la estufa y los gabinetes desprotegidos adyacentes y
por encima son de 30" (76.2 cm).
* 30" (76.2 cm) min. para un gabinete desprotegido.
24" (61 cm) min. para una superficie protegida.
Salida de Aire
Entrada de Aire
Fresco
4"el x 8" (10.2 cm x 20.3
cm) apertura en la parte
posterior derecha para
encaminar el cable
armado si un panel
_sta presente
Las esquinas
de esta unidad son fragiles.
Cuidadosamente instale la
estufa sujetandola por los
lados. AI instalarla, nunca
deje que el peso del aparato
se recargue sobre una sola
esquina.
Figura 1
DIMENSIONESDELAESTUFA
MODELO AANCHURA B PROFuNDDAD CALTURA DANcHoDELACA]A E PROFUNDIDADDELAcAJA
Modelo30" 303A(78.1) 21V2(54.6) 2_A(5.1) 29(73.7) 193/8(49.2)
Modelo36" 363A(93.3) 27/2(54.6) 2_A(5.1) 35(88.9) 193/8(49.2)
DIMENSIONESDERECORTADO
F.ANCHURA G.PROFUNDIDAD HALTURA
MODELO MINIMA M_IivIA MINIMA M_IMA DEBAJODE¼ESTUFA*
Modelo30" 29%(75.2) 30(76.2) 20_A(51.4) 20Y2(52.1) 6(15.2)
Modelo36" 35%(90.5) 36(91.4) 20_A(51.4) 20Y2(52.1) 6(15.2)
Todas las dimensiones se dan en pulgadas (cm).
* Deje 2" (5 cm) de hueco debajo de la estufa para espacio para el cable electrico y la
instalaciOn de la caja de empalmes en la pared detrSs de la estufa.
Impreso en los Estados Unidos
P/N 318201435 (0706) Rev.
English - pages 1-6
Espaflol - pages 7-12

Elarmariosuperiornodebesobrepasaruna
profundidadmaximade13"(33cm)
30"(76.2cm)rain.
deespacioentrela
partesuperiordel
fog6nylaparte
inferiordeunarmario
demaderaometal
sinprotecci6n.
24"(61cm)rain.
cuandolaparteinferior
delarmariodemadera
ometalest,1protegida
porunaplaca
cortafuegoretardante
dellamadenomenos
de1/8",cubiertacon
unaKiminadeacero
msgnoinferioralNo.
28,deaceroinoxidable
de0.015",aluminiode
0.024"ocobrede
0.020".
18"
(45.7cm)
' c.
2" (5.1 cm) rain. distancia
recomendada entre el
horde trasero del corte y el
compartimiento de
combustible m_is cercano
sobre la parte superior del 10"
armario cm)
G
Ubicacion aproximada
de la caja de empalmes
21/2" (6.4 cm) rain. desde el borde delantero del
corte hasta el borde delantero de la parte
superior del armario
7Y2" (19.1 cm)
min. desde el
borde del corte
hasta el
compartimiento
de combustible
(ambos lados
del artefacto)
No es recomendable utilizar
cajones debajo de la estufa.
Para las dimensiones vease la tabla en la pagina 1.
Para evitar riesgos de
quemaduras o incendios al tocar superficies
calientes, se deben evitar los armarios sobre
lasuperficiedelosquemadores. Siexiste un
armario, se pueden reducir los riesgos
instalando una campana que se extienda
horizontalmente en un minimo de 5" (12.7
cm) pot sobre la parte inferior de los
armarios.
Figura 2- ELCORTE DE LA PARTE SUPERIOR DEL ARMARIO

Notas importantes para el instalador
1. Lea todas lasinstrucciones contenidas en este manual
antes de instalar la estufa.
2. Saque todo el material usado en el embalaje de la
estufa antes de conectar el suministro electrico a la
estufa.
3. Observe todos los c6digos y reglamentos pertinentes.
4. Deje estas instrucciones con el consumidor.
Nota importante al consumidor
Conserve estas instrucciones y el Manual del usuario para
referencia futura.
INSTRUCCIONES
IMPORTANTES DE SEGURIDAD
• Asegurese de que su estufa sea instalada y puesta
a tierra de forma apropiada pot un instalador
calificado o pot un t&cnico de servicio.
•Esta estufa debe set el&ctricamente puesta a tierra
de acuerdo con los c6digos locales o, en su
ausencia, con el C6digo El&ctrico Nacional ANSI/
NFPA No. 70 - ultima edici6n en los Estados
Unidos, o el C6digo El&ctrico Canadiense CSA
Standard C22.1, Part 1 en Canada.
La alimentaci6n el&ctrica a la estufa
deberia apagarse mientras se hacen las conexiones
de linea. El no harcelo podria resultar en da_os
serios o la muerte.
Provea conexion electrica
Instale la caja de empalmes debajo del armario y provea
un cable de 120/240 o 120/208 Voltios, AC al panel de
circuitos del aparato. NO conecte la cable al panel de
circuitos en este momento.
Requisitos electricos
Se debe proveer el voltaje y la frecuencia apropiados a este
electrodom6stico, y conectarse a un circuito individual
correctamente puesto a tierra, protegido por un interruptor
o un fusible. Para saber si el interruptor o fusible es
recomendado para su modelo, vea la plata serial para
encontrar el consumo de potencia en vatios y refierase a la
tabla A para conseguir el interruptor o el fusible del amperaje.
GradosdeVatios Serecomienda Gradosde Vatios Serecomienda
de] unaprotecci6n del unaprotecci6n
electrodomestico a]circuito electrodomestico al circuito
240V 208V
Menosde 4800W 20A Menosde4100W 20A
4800W- 7200W 30A 4100W - 6200W 30A
7200W- %00W 40A 6200W -8300W 40A
9600Wy + 50A 8300Wy + 50A
Tabla A
Cumpla con todos los c6digos en vigor y todos los
reglamentos locales.
1. Parael suministro electrico solamente se necesita
corriente con frecuencia de 60 Hz AC y fase tinica de
120/240 o 120/208 voltios suministrada por cable de
3 o de 4 alambres en un circuito separado con fusibles
en ambos lados de la linea (serecomienda un fusible
de tiempo retardado o un cortacircuitos). NO ponga
un fusible en el hilo neutro.
NOTA: Eltamaflo de los cables y de las conexiones debe
de estar en conformidad con el tamaho del fusible y con la
capacidad del electrodomestico y de acuerdo con el
C6digo Electrico National ANSI/NFPANo. 70 - Liltima
edition y los c6digos y reglamentos locales.
No se debe usar una alargadora para
enchufar este electrodomestico. Esto podria resultar
en un incendio, un choque el&ctrico u otto tipo de
daEo personal.
2. Esteelectrodomestico debe conectarse a la caja de
fusibles (o de cortacircuitos), por medio de un cable
blindado flexible o un cable con forro no metalico. El
cable blindado flexible que va desde el
electrodomestico debe de estar conectado
directamente a la caja de empalme. Lacaja de
empalme debe de estar Iocalizada en el lugar que se
indica en la Figura 2, dejando tanto exceso de cable
como sea posible entre la caja y el electrodomestico,
de forma que asi el electrodomestico se pueda mover
facilmente, si fuera necesario para hacer una
reparacion.
3. Se debe de usar un conectador que reduzca la tirantez
de una forma adecuada para unir el cable blindado
flexible a la caja de empalme.

Instrucciones de desembalaje
Plata con los numeros de modelo y serie
(debajo de la cubierta)
Figura 3
.
2.
Deje los soportes de las esquinas en la estufa hasta
la terminaci6n de la Conexi6n Electrica.
Asegurese que la botella de limpiador ubicada en la
empaquete de literatura esta situada en un lugar
donde puede encontrarse facilmente, Esimportante
de tratar de antemano la superficie en vidrio de
ceramico antes de utilizar, Ve a la parte sobre
Limpieza y IVlantenimiento de la Cubierta en
este Mlanual del usuario.
Conexion Electrica
Conecte el cable blindado flexible que se extiende desde la
superficie del artefacto hasta la caja de empalmes
utilizando una grapa de alivio de tension adecuada en el
punto en que el cable blindado entra en la caja de
empalmes. Realizar luego la conexiOn electrica de la
siguiente manera.
En este electrodomestico se necesita un cable de
puesta a tierra.
Este electrodom&stico viene equipado
con un cable de conexi6n de cobre. Si esto tuviera que
conectarse a los cables de aluminio de una casa, use
solamente los conectores especiales aprobados para
empalmes de cobre y aluminio, de acuerdo con el
C6digo El_ctrico Nacional ylos reglamentos yc6digos
locales. Una conexi6n incorrecta del alambrado de
aluminio con los conductores de cobre puede resultar
en un cortacircuito o incendio.
Este electrodomOstico se fabrica con un alambre de puesta
a tierra verde (o de cobre sin forro) conectado con el
marco.
NO conecte el alambre puesto a tierra
a una tuberia de suministro de gas. NO conecte el
suministro de energia el&ctrica hasta que el
electrodomestico haya sido permanentemente puesto
a tierra. Antes de encender la alimentaci6n el&ctrica;
conect& de manera permanente el cable de tierra,
despu&s complete todas las conexiones restantes.
Asegure la tapa protectora de la caja de
ensambladura.
Donde los c6digos locales permitan conectar el
conductor de puesta a tierra del el&ctrodom&stico al
neutral (blanco)
Si su cocina tiene un cable de 3 hilos que debe
conectarse a una caja de juntas con conexi6n a tierra
de 3 hilos (vet figura 4):
1. Desconecte el suministro electrico.
2. En el interruptor automatico, caja de fusibles o caja de
juntas: conectar el aparato y los cables residenciales
como se muestra en la figura 4.
Cable desde el suministro de energia
Alambre
blanco (neutrab_ _ Alambre
:roempalmes
vjdrde L_ Conductor de uni6n
Alambre _ _ listado-UL (o CSA)
o desnudo Cable_-_dela estufa
Figura 4- CAJA DE EMPALMES
DE 3 ALAMBRES PUESTA A TIERRA
10