Kenmore 911.47712 User manual

Installation
Instructions 30" Built-In Wall Oven
911.47712,47714,47719,47752,47754,47759,
49042,49043,49044,49049,49052,49053,
49054,49059
I If you have questions, contact our website at: www.sears.com I
Before You Begin
Read these instructions carefully and completely.
• IM PO RTANT-save these
instructions for local inspector's use.
• IMPORTANT-observe all
governing codes and ordinances.
•Note to Installer--Be sure to leave these
instructions with the consumer.
•Note to Consumer--Keep these
instructions for future reference.
•Proper installation is the responsibility
of the installer and product failure due
to improper installation is NOT covered
under the warranty.
•NOTE--This appliance must be properly
grounded.
•ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box, A plug and receptacle is NOT permitted
on these products,
Parts Included
Metal
Bottom Trim
Screws For
Installation Plastic
Bottom Trim
Materials Needed
Strain Relief Clamp
for 1/2" conduit @
Junction
Box
Wire Nuts
36" of String
Tools Needed
1/8" Drill Bit and
Electric or Hand Drill Phillips Screwdriver
229c4053P499-4
31-10518-4 243JR 1

Installation Instructions
IMPORTANT SAFETY INSTRUCTIONS
For Your Safety
•Be sure your oven is installed properly by
a qualified installer or service technician.
• Be sure the oven is securely installed in a
cabinet that is firmly attached to the house
structure. Weight on the oven door could
cause the oven to tip and result in injury.
Never allow anyone to climb, sit, stand or
hang on the oven door.
• Make sure the cabinets and wall coverings
around the oven can withstand the
temperatures (up to 200°F) generated
by the oven.
WARNING: The electrical
power to the oven supply line
must be shut off while line
connections are being made. Failure
to do so could result in serious injury
or death.
Electrical
Requirements
This appliance must be supplied with the
proper voltage and frequency, and connected
to an individual, properly grounded branch
circuit, protected by a circuit breaker or fuse
having amperage as noted on rating plate.
(Rating Plate is located on oven frame.)
We recommend you have the electrical wiring
and hookup of your oven connected by a
qualified electrician. After installation, have the
electrician show you where your main oven
disconnect is located.
Check with your local utilities for electrical
codes which apply in your area. Failure to wire
your oven according to governing codes could
result in a hazardous condition. If there are no
local codes, your oven must be wired and fused
to meet the requirements of the National
Electrical Code, ANSI/NFPA No. 70-Latest
Edition. You can get a copy by writing:
National Fire Protection Association
Batterymarch Park
Quincy, MA 02269
Effective January 1, 1996, the National
Electrical Code requires that new, but not
existing, construction utilize a four-conductor
connection to an electric oven. When installing
an electric oven in new construction, a mobile
home, recreational vehicle or an area where
local codes prohibit grounding through the
neutral conductor, follow the instructions in
the section on NEW CONSTRUCTION AND
FOUR-CONDUCTOR BRANCH CIRCUIT
CONNECTION.
You must use a three-wire, single-phase A.C.
208Y/120 Volt or 240/120 Volt, 60 hertz
electrical system. If you connect to aluminum
wiring, properly installed connectors approved
for use with aluminum wiring must be used.
2

Installation Instructions
Pre-lnstallation Checklist
ALL INSTALLATION INFORMATION
ON THE FOLLOWING PAGES IS TO
BE USED FOR SINGLE AND DOUBLE
OVEN INSTALLATION!
Remove packaging materials.
Check behind hinges and under
false bottom. Remove labels on the
outside of the door, plastic on trims
and panel, all tape around the oven,
and any shipping screws securing
the oven to the base pad.
Oven Racks
Broiler Pan
and Grid Literature
Pack
Open oven door and remove literature
pack, broiler pan and grid, and oven
racks.
Remove Installation Instructions from
literature pack and read them carefully
before you begin.
Be sure to place all literature, Use and
Care, Installations, etc. in a safe place
for future reference.
m
Door removal is not a requirement for
installation of the product, but is an
added convenience. To remove the door:
Open the oven door as far as it will go.
Push both hinge Hinge
_ _'qb,,. Unlocked
locks down toward . ._i_l /
',_'I Position
the door frame, Hmgei/_,i
to the unlocked s_ot _
position. This may
require a flat blade Hinge
screwdriver. Arm
DO NOT LIFT THE DOOR
BY THE HANDLE!
Place hands on both sides of
the door, and close the oven
door to the removal position.
This is half way between the
broil stop and fully closed.
[_ Lift door up and
out until the
hinge arms
clear the slots.
Hint e Clears Slot
NOTE: The oven door is very heavy, Be sure
you have a firm grip before lifting the oven
door off the hinges, Use caution once the
door is removed. Do not lay the door on its
handle, This could cause dents or scratches,
(Continued on following page)
3

Installation Instructions
[_ Pre-lnstallation Checklist cont.
d
Place the oven on a table or platform
even with the cutout opening.
(Platform must support 150 Ibs. single,
275 Ibs. double.)
Remove the bottom trim from the top
of the oven. It will be installed at the
end of the installation process. The
trim is wrapped separately and taped
to the top of the unit.
4

Installation Instructions
I-A-11Cutout for Single Built-In Oven
Allow 11/16" for
overlap of oven
over side edges
of cutout
21
Allow a minimum of
21" for clearance to
adjacent corners,
drawers, walls, etc.
when door is open
Cutout Cabinet Width 30"
Width
28 1/2" Min.
Between
inside Walls
Must Be
At Least
28 1/2- Wide
Allow 1" minimum
for overlap of
oven top and and
1_/4"for bottom
of cutout
Cabinet
Width
30"
I
I
I
Height
27 1/4" Min. i
27 5/16" Max,_
Recommended
minimum cutout
location from
floor 32 1/2"
Junction Box
22" to
Bottom of
Junction Box
Recommended
Minimum
Cutout Location
from Floor
Cutout Depth
Cutout Width
Cutout Height
32 1/2"
23 1/2" Min.
28 1/2" Min.
28 5/8" Max.
27 1/4" Min.
27 5/16" Max.
NOTE: If the cabinet does not
have a front frame and the
sides are less than 3/4" thick,
shim both sides equally to
establish the cutout width.
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For single
ovens, the runners and braces must
support 150 Ibs.
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
Suitable
Bracing
to Suppo_
Runners--
21 5/8"
Over Centerline
of Cabinet
-- 2"x4"or
equivalent
runners
level with
the bottom
of cutout
This oven is not approved for
stackable or side by side installation.
5

Installation Instructions
Cutout for Double Built-In Oven
Allow 11/16" for
overlap of oven
over aide edgea
of cutout
Allow aminimum of
21" for clearance to
adjacent corners_
drawers, walls, etc.
when door is open
21"
Cutout
Width
28 l/2"Min,
<--28 518" Max. -'_
Opening
Between
Inside Wails
Must Be
At Least
28 1/2" Wide
Allow 1"
minimum for
overlap of oven
top and 1V¢'
for bottom
of cutout
_5"fJunction Box
47" to
Bottom of
Junction Box
Height
51 13116" Min.
15/16" Max.
_._-_'_ _ Recomn_ended
30"_-_-L I minimum cutout location
Cab'met_--_____rom ,floor 12"
Width
Cabinet Width 30"
Recommended
Minimum
Cutout Location
from Floor
Cutout Depth
Cutout Width
Cutout Height
12"
23 1/2" Min.
28 1/2" Min.
28 5/8" Max.
51 13/16" Min.
51 15/16" Max.
NOTE: If the cabinet does not
have a front frame and the
sides are less than 3/4" thick,
shim both sides equally to
establish the cutout width.
If the cabinet does not have a solid bottom,
two braces or runners must be installed
level with the bottom of the cutout to
support the weight of the oven. For double
ovens, the runners and braces must
support 275 Ibs.
NOTE: If marks, blemishes or the
cutout opening are visible above the
installed oven, it may be necessary to
add wood shims under the runners and
front trim until the marks or opening
are covered.
Suitable
Bracing
to Support
Runners --
_21 5/8"_
r Centerline /
of Cabinet
--2"x4"or equivalent
runners
level with
bottom of
cutout
6

Installation Instructions
I_ Cutout for Single Built-In Oven
Under Counter
Gas or electric cooktops may
be installed over this oven.
See cooktop installation
instructions for cutout size.
See label on top of oven for
approved cooktop models.
Top and/or side fillers
may
between existing
cabinets. Be sure
they are attached
securely, since they
will anchor the oven
• in the cabinet.
240V /208V
Junction Box
Location
1" overlap for
top of oven and
_._11/16" overlap
for side edges
of cutout
Gas and electrical connections for
30" gas cooktop must be located
in an adjacent accessible location
to the right. For 36" gas cooktop,
the connections may be made
to the left.
22" Min. 36"
Above Typical
Support Countertop
Platform Height
I
sJ*_
3/4"
Support Platform
Required 5 9/16"
Reference dimension for
maximum support height with
typical 36" countertop height
MUST SUPPORT 150 LBS.
II installed under a solid disk, induction III
or downdraft modular cooktop.
7

Installation Instructions
I-B-]Electrical Connections
ATTENTION INSTALLER
All electric wall ovens must be hard wired
(direct wired) into an approved junction
box. A plug and receptacle is NOT permitted
on these products.
DO NOT shorten the flexible conduit.
The conduit strain relief clamp must be
securely attached to the junction box
and the flexible conduit must be securely
attached to the clamp. If the flexible
conduit will not fit within the clamp, do not
install the oven until a clamp of the proper
size is obtained.
NOTE TO ELECTRICIAN: The 3 power
leads supplied with this appliance are
UL recognized for connection to heavier
gauge household wiring. The insulation
of these 3 leads is rated at temperatures
much higher than the temperature rating
of household wiring. The current carrying
capacity of the conductor is governed
by the wire gauge and the temperature
rating of the insulation around the wire.
WARNING: Improper
connection of aluminum house
wiring to copper leads can
result in an electrical hazard or fire.
Use only connectors designed for
joining copper to aluminum and follow
the manufacturer's recommended
procedure closely.
Turn off the circuit breaker or remove
fuses to the oven branch circuit.
With the oven supported on a table or
platform in front of the cabinet opening,
connect the flexible conduit to the
electrical junction box as shown below.
Position the conduit in such a manner
that it will lie on top of the oven in
a natural loop when the oven is
installed. You will need to purchase
an appropriate strain relief clamp to
complete the connection of the conduit
to the junction box.
Junction Box ,,
Location -t-5-4-
Paceoe o s_l _-_ 1/ (notincluded)
support to assist in '_ must be used at
connecting conduit Junction Box
8(Continued on following page)

Installation Instructions
I-B-]Electrical Connections cont.
New Construction and
Four Conductor Branch
Circuit Connection
•When installing in new construction, or
• When installing in a mobile home, or
• When installing in a recreational vehicle, or
• When local codes do not permit grounding
through neutral:
a. Cut the neutral (white) lead from the crimp.
Re-strip the neutral (white) lead to expose
the proper length of conductor.
_Junction Box
Cover
b. Attach the appliance grounding lead (green
or bare copper) in accordance with local
codes. If the residence grounding conductor
is aluminum, see WARNING on page 8.
c. Connect the oven neutral (white) lead to
the branch circuit neutral (white or gray)
in accordance with local codes, using a
wire nut.
d. Connect the oven red lead to the branch
circuit red lead and the oven black lead to
the branch circuit black lead in accordance
with local codes, using wire nuts. If the
residence red, black or white leads are
aluminum conductors, see WARNING on
page 8.
e. Install Junction Box Cover.
Three-Conductor Branch
Circuit Connection
When connecting to a three-conductor branch
circuit, if local codes permit:
a. Connect the bare oven ground conductor
with the crimped neutral (white) lead to
the branch circuit neutral (white or gray
in color), using a wire nut.
b. Connect the oven red lead to the branch
circuit red lead in accordance with local
codes, using a wire nut.
c. Connect the oven black lead to the branch
circuit black lead in accordance with local
codes, using a wire nut. If the residence
red, black or white leads are aluminum
conductors, see WARNING on page 8.
d. Install Junction Box Cover.
9

Installation Instructions
Securing the Oven in the Opening
Sliding the Oven Into the
Opening
a. Loop (do not tie) a 36" string around the
conduit before the oven is slid into place.
This will keep the conduit from falling
behind the oven.
Pull out on
string loop
while pushing
the oven into
BB the cabinet
b. Lift oven into cabinet cutout using the oven
opening as a grip. Carefully push against
oven front frame. Do not push against
outside edges.
c. As you slide the oven back, pull the string
so that the conduit will lie on top of the
oven in a natural loop.
d. When you are sure the conduit is out of the
way, slide the oven 3/4 way back into the
opening. Remove the string by pulling on
one end of the loop.
I-_ Drilling the Pilot Holes and
Mounting the Oven
NOTE: Before drilling the pilot holes,
make sure the oven is pushed as far
back into the opening as it will go
and centered.
a. Drill holes through the mounting holes (top
and bottom) of the side trim, for the #8
screws provided.
The screws must
be a minimum of
1/4" from the front
of the cutout.
_i WARNING: Mounting
screws must be used. Failure to
do so could result in the oven
falling out of the cabinet causing
serious injury.
w
b. Secure the oven to cabinet with screws
provided.
NOTE: If the cabinet is particle board, you
must use #8 x 3/4" particle board screws.
These may be purchased at any hardware
store.
10 (Continued on following page)