Kenmore Kenmore 911.47485 User manual

OWNER'S MANUAL
27" SELF-CLEANING
BUILT-IN WALL OVEN MODEL NO.
911.47485
911.47486
911.47489
CAUTION:
Before using this oven,
read this manual and
follow all its Safety Rules
and Operating
Instructions.
• Safety Instructions
• Operation
•Care and Cleaning
•Problem Solving
Sears, Roebuck and Co., Hoffman Estates, IL 60179 U.S.A.
229C4020P195-1 (SR-10404)

Table of contents 27" SELF-CLEANINGOVEN
Oven Safety ........................... 3-4
Features of Your Oven .............. 5
Removal of Packaging Tape .... 5
Oven Control, Clock, Timer ...... 6
Control Display ......................... 7
Clock ........................................ 8
Kitchen Timer ........................... 8
Tones ........................................ 9
F Code ...................................... 9
Oven Cooking Tips ............ 10-11
Baking .................................... 12
Broiling ................................... 13
Setting Special Features ... 14-15
Self-Cleaning Cycle ........... 16-17
Control Panel .......................... 18
Broiler Pan and Grid ............... 18
Self-Cleaning Oven Interior .... 18
Oven Light Bulb ...................... 18
Oven Racks ............................ 19
Oven Door .............................. 19
Before Calling for
Service ............................... 20-21
Temperature Adjustment ....... 22
Warranty ................................. 23
Consumer Service Numbers ... 24
For your convenience and future reference, please write down
your model and serial numbers in the space provided. They are
located on the front frame behind the oven door.
MODEL NUMBER: SERIAL NUMBER:
2

IMPORTANTSAFETY
INSTRUCTIONS
SAVE THESE INSTRUCTIONS
Read all instructions before using this appliance. When using
gas or electrical appliances, basic safety precautions should
be followed, including the following:
IMPORTANT: To insure safety for
yourself, family and home, please
read your Owner's Manual carefully.
Keep it handy for reference. Pay
close attention to Safety Sections.
BE SURE your appliance is
installed and grounded by a qualified
technician.
• DO NOT leave children alone or
unattended near an appliance in
use.
• TEACH CHILDREN not to play
with controls or any part of the
appliance, and not to sit, climb or
stand on the door or any parts of
the appliance.
•CAUTION: NEVER STORE
items of interest to children in
cabinets above the appliance.
Children climbing on the appliance
could be seriously injured.
• KEEP THIS book for later use.
•NEVER TRY to repair or replace
any part of the appliance unless
instructions are given in this
manual. All other work should be
done by a qualified technician.
•NEVER USE your appliance for
warming or heating the room.
•ALWAYS KEEP combustible wall
coverings, curtains, dishcloths,
towels, potholders, and other linens
a safe distance from the appliance, 3
•NEVER USE a towel or other
bulky cloth as a potholder and
make sure the potholder is dry.
Moist potholders could cause
steam burns. DO NOT let
potholders touch hot surfaces,
•ALWAYS KEEP the appliance
area free from things that will burn.
Food, wooden utensils, and grease
buildup could catch fire. Plastic
utensils could melt and canned
foods could explode. Your
appliance should never be used as
a storage area.
•ALWAYS KEEP your appliance
clear of things that will burn
(gasoline and other flammable
vapors or liquids).
• NEVER HEAT unopened food
containers. Pressure buildup can
cause the container to burst and
cause injury.
•NEVER LEAVE jars or cans of fat
or drippings in your oven.
•NEVER TRY to clean a hot
surface. Some cleaners produce
noxious fumes, and wet cloths or
sponges could cause steam burns.
•NEVER WEAR loose fitting
clothing when using your
appliance.
•BE SURE the oven is securely
installed in a cabinet that is firmly
attached to the house structure.

IMPORTANTSAFETY
INSTRUCTIONS
•DO NOT touch heating elements,
surfaces near them, or interior oven
surfaces. These may be hot enough to
cause burns even though they are
dark in color, During and after use, do
not touch or let clothing or flammable
material contact the elements or hot
surfaces until they have had time to
cool. Other surfaces near the oven
vent openings, oven door, and
window may also be hot enough to
cause burns.
• J,,,, :_m
• PLACE OVEN RACKS in the
desired position while the oven is
cool. If racks must be moved while
oven is hot, do not _etpotholder
contact the hot oven element.
•AFTER BROILING always take the
broiler pan and grid out of the oven
and clean them. Leftover grease in the
broiler pan could catch fire the next
time you use your oven,
•ALWAYS USE care when opening
the oven door. Let hot air and steam
escape before moving foods.
•NEVER USE aluminum foil to _inethe
oven bottom. Improper use of foil
could start a fire, or electrical shock
could result.
•NEVER BLOCK the oven vent
opening.
•CLEAN ONLY the parts listed in this
manual. Follow all cleaning
instructions.
•NEVER RUB, move or damage the
door gasket on self-cleaning ranges.
• NEVER TRY to clean utensils,
cookware, removable parts or broiler
pan and grid in the self-clean cycle.
•DO NOT USE oven cleaners - No
commercial oven cleaner or protective
coating of any kind, should be used in
or around any part of the oven.
IMPORTANT SAFETY
NOTICE!
The California Safe Drinking
Water and Toxic Enforcement
Act requires the governor of
California to publish alist of
substances known to the state
to cause birth defects or other
reproductive harm and requires
businesses to warn their
customers of potential
exposure to such substances.
The fiberglass insulation in a
self-cleaning oven will give off
a very small amount of carbon
monoxide during the cleaning
cycle. Exposure can be
minimized by venting with an
open door or window or using a
ventilation fan or hood.
IMPORTANT: The health of
some birds is extremely
sensitive to the fumes given off
during the self-cleaning cycle
of any range. Move birds to
another well.ventilated room.
READ AND UNDERSTAND
THIS INFORMATION
NOW!
Be sure everyone in your home
knows what to do in case of
fire. Never use water on a
grease fire; it will only spread
the flames.
OVEN FIRE:
Do not try to move the pan!
f. Close the oven door and turn
controls off.
4
2. If fire continues carefully open the
door, throw baking soda on the
fire, or use a dry chemical, foam,
or halon type extinguisher.

OPERATION
FEATURESOF YOUROVEN
Self-Clean
Automatic
Oven Control ;et Pad
Oven Light
:witch
Automatic Oven
Oven L
Broiler Pan
And Grid
Model & Serial
Number
Self-Cleaning
Oven Interior
Removable Oven
-Racks
Self-Cleaning
Door Gasket
Removable
Oven Door
To remove the adhesive left from packaging tape, use household dishwashing
liquid, mineral oil or cooking oil. With a soft cloth rub into the area and allow to
soak. Rinse and dry well. Repeat procedure using an appliance polish to insure
no damage is done. This should he done before the oven is turned on
for the first time. The tape cannot be removed once the oven has
heated. Packaging tape may be found in the following areas: door handle,
control panel area, door trim and oven area,
5

OPERATION
OvenControl,Clockand Timer
G3 @ @@
TEMP HOUR MIN
@ QQ @
Your new touch pad oven control will
allow you to set oven functions with
ease. Below are the different types of _/"Z_, The HOUR/MIN UP and
functions and adescription of each. /(_,)/(,._ DOWN arrow pads set the
_-, if j, ,HOUR MIN time of day, length of
_t'_"_ _ cooking time, length of
_ cleaning time, the delayed
BAKE -- Cooks foods in the traditional
oven with a temperature range of 170°F
to 550_F.
BROIL -- Cooks foods at 550°F HI
broil or 450° LO broil from the direct TEMP
heat of the upper element. Broiling ('V_
ehould be done with the door opened to
the broil stop position.
CLEAR -- Cleans the inside area of
the oven for you. When the cycle is
finished, the oven will turn off
automatically.
Set the amount of time you
want foods to cook or the
oven to clean. The oven turns
off automatically at the end of
this time,
®
®
KITCHEN
TIMER
Set the time of day you want
the oven to turn on The oven
will turn on automatically at
the time you have set. When _CLOCK_
DELAY START TIME is
used with OVEN COOKING
TIME, the oven will also turn
off automatically, at the end ot
the cooking time,
start time, and the time set
on the Kitchen Timer.
The TEMP UP and
DOWN arrow pads set the
temperature used for
cooking.
The START pad must be
pressed to activate any
oven function.
The CLEAR/OFF pad is
used to cancel any oven
function and the end of
cycle tone. It will not
cancel the Clock or
Kitchen Timer.
The KITCHEN TIMER
ON/OFF pad is used to
turn the Kitchen Timer on or
off. It will not control any of
the other oven functions.
The CLOCK pad is used to
set the time of day.
Turns oven light on or off.
6

ControlDisplay OPERATION
Flashing
Indicator To
Alert You
A Temperature
Or A Time
Oven Temperature
Indicator
Oven Function
Indicator
The Control Display is an easy
reference for using your oven control.
Below are descriptions of how the
Control Display works.
OVEN TEMPERATURE
INDICATOR -- This indicator has a
multiple purpose.
• Displays the temperature
•Displays an error code --
"ERR" -Ifthe oven temperature
indicator flashes "ERR", then you
have set an invalid time or
temperature.
• Displays Oven Problems -- If
your control flashes "F" and a
number or letter, you have
experienced an oven problem.
Please read the section on
F-CODES in your manual.
"ON" INDICATOR -- Will light
when the oven turns on.
indicetor To Let You
Know the Oven Has
Turned On
Location For The
- Time Of Day Clock,
Kitchen Timer,
Delay Start Time,
Or Oven Cooking
Oven Function
Indicator
SET INDICATORS -- The set
indicator will flash in combination with
an oven function or timed function to
let you know you need to set a time or
temperature. Example: "SET" and
"RAKE" will Flash to let you know
you need to set the bake temperature.
TIMED INDICATOR -- Displays
the time of day, cooking time, delay
start time, cleaning time or the time
set on the Kitchen Timer,
•Displays a reminder code --
"PUSH START"-If the time
indicator flashes the word "PUSH
START", then you need to press
the START pad to activate your
setting.
OVEN FUNCTION INDICATORS
Displays which oven function has
been set, when the oven door locks,
and if the function is delayed.
7

OPERATION
Clockand Timer
The clock must be set for the correct
time of day before a delayed oven
function can work properly. The time
of day cannot be changed during a
timed oven function, but can be
changed during a bake or broil
function.
HOW TO SET THE CLOCK
1. Press the CLOCK pad.
2. Press the HOUR/MIH UP and/or
DOWN arrow pads to set the
time.
3. Press the START pad.
RECALL THE CLOCK
While using your oven for cooking,
press the CLOCK pad if you wish to
check the time of day. The current
time of day will show in the display.
POWER FAILURE
tf you have experienced a power
failure, the time will flash in the display
and will be incorrect. Reset your
clock.
Any oven cooking function that was in
process will need to be reset.
The Kitchen Timer is used to time
cooking processes or other
household activities. It does not
control the oven. It can be set for up
to 9 hours and 59 minutes. It will
count down in minutes until the LAST
68 SECONDS is reached, then the
control will beep once. When the
countdown reaches ZERO, the
control will beep 3 times followed by
one beep every 6 seconds until the
KITCHEN TIMER ON/OFF pad is
pressed. The 6 second beep can be
removed for future cycles if desired.
For directions on removing this
continuous beep, see Tones on the
following page.
HOW TO SET THE TIMER
1. Press the KITCHEN TIMER
ON/OFF pad.
2. Press the HOUR/MIN UP and/or
DOWN arrow pads to set time.
3. Press the START pad.
4. When the countdown has reached
zero, press the KITCHEN
TIMER ON/OFF pad to turn off
the beep.
To cancel the timer during the
countdown, press the KITCHEN
TIMER ON/OFF pad TWICE.
8

OPERATION
Oven Control, Clock and Timer
Your new control has a series of tones
that will sound at different times. These
tones may sound while you set the
control for an oven function, or at the
end of the oven function. It will also alert
you that there may be a problem with
the functions. Below are the types of
tones and a brief description of each.
TONES WHILE SETTING THE
CONTROL --When you press a touch
pad you will hear a beef This beep will
let you know you have placed enough
pressure on the pad to activate it. (The
arrow pads do not beep.)
END OF TIMED CYCLE TONE
At the end of a timed cooking function,
you will hear 3 short beeps followed by
1beep every 6 seconds. This 6
second beep will continue to sound
until the CLEAR/OFF pad is pressed
or you may select the special feature to
cancel this 6 second beep from
sounding at the end of future cycles.
TO CANCEL THE 6 SECOND
BEEP
1. Press and ho_dthe BAKE and
BROIL pads, at the same time
for 3 seconds, until the display
shows "SF".
2. Press the KITCHEN TIMER ON/
OFF pad. The display will show
"CON BEEP" (continuous beep).
3. Press the KITCHEN TIMER ON/
OFF pad again. The display will
show "BEEP" (beep canceled).
4. Press the START pad to cancel the
6 second beep and leave the
special feature mode.
If you would like to return the 6 second
beep, repeat steps above until the
display shows your choice and press
the START pad
ATTENTION TONE -- This tone will
sound if you make an error or an
oversight is made while setting an
oven function.
Examples would be:
a. Setting a clean cycle and the oven
door is not properly closed.
b. Setting function and not pressing the
START pad.
c. Pressing an additional function pad
without first setting a temperature or
time.
d. ERR will flash if you set an invalid
temperature. Press the CLEAR/
OFF pad to clear the control and
reset the oven function.
Any of these can be quickly identified
by watching the display.
PREHEAT TONE --When you set an
oven temperature, the oven
automaticatly starts to heat. When the
temperature inside the oven reaches
the temperature you have set, a tone
will sound to let you know the oven is
ready for baking.
If you set an oven function and the
control beeps while the display is
flashing "F" and a number or letter
such as "F-4" or "FI," there may be a
problem with the control or oven.
Simply press the CLEAR/OFF pad and
wait about an hour. Try setting the
function again. If the code repeats, write
down the flashing code and call for
service. Tell the technician what code
was flashing.

OPERATION
OvenCookingTips
It is normal to have some odor when
using your oven for the first time. To
help eliminate this odor, ventilate
the room by opening a window
or using a vent hood
IMPORTANT: Never cover the oven
bottom or oven rack with aluminum
foil. Improper use can cause poor
heat flow, poor baking results, and
may damage the oven finish To
prevent staining from spiliovers, you
may place a piece of aluminum foil or
a cookie sheet below foods which
may spill over.
The oven vent is located under the
control panel. This area could become
hot during oven use. The vent is
important for proper air circulation.
Never block this vent. Oven Vent
Location
Opening the door often to check
foods will cause heat loss and poor
baking results.
Preheating is bringing the
temperature up to the temperature
you will be using during baking. Let
the oven preheat thoroughly when
recipes call for preheating.
In the back of the oven you will notice
a small tube. This is a heat sensor
that maintains the temperature of the
oven. Never move or bend this tube.
-__ Oven
erature Sensor
The low temperature zone of your
oven (between 170 ° and 200°F) is
available to keep hot cooked foods
warm. However, foods should not be
kept at these temperatures longer
than 2 hours.
When using your convenient Delay
Start operation, foods such as dairy
products, fish, poultry, etc., should
never sit more than 1 hour before
cooking. Room temperatures and the
heat from the oven light promote
bacterial growth.
Most recipes for baking have been
developed using high-fat products
such as butter or margarine (80% fat
by weight--the federal requirement
for products labeled "margarine")
You will get poor results if cakes, pies,
pastries, cookies or candies are made
10 continued on next page

OPERATION
Oven Cooking Tips
Margarine (cont,)
with low-fat spreads. Low-fat spreads
contain less fat and more water. The
high moisture content of these
spreads affects the texture and flavor
of favorite baked recipes. The lower
the fat content of a spread product,
the more noticeable these differences
become. To ensure best results, use
margarine, butter or stick spreads
containing at least 70% vegetable oil.
The Oven Temperature Sensor at the
back of the oven continuously senses
and controls the temperature inside the
oven. To keep aconstant set
temperature, the elements will cycle or
turn on and off during cooking.
If baking with more than one pan, place
the pans so each has at least 1 to 1 1/2"
of air space around it. Place pans so
one is not directly above the other.
SHINY PANS reflect heat, and are
perfect for cakes and quick breads that
need a light brown crust.
GLASS, DARK NON-STICK OR
DARKENED BY AGE BAKE-WARE,
absorb heat, and can be used for yeast
breads, pie crust or foods that need a
brown crust. The oven temperature,
when using these pans should be
reduced by 25°F.
The oven racks are designed with stop
locks, a convenience as weI_as a safety
precaution. The guides have a bump to
prevent the racks from tilting when
racks are pulled out of the oven.
Youroven has four (4) rack positions.
The area above the top guide cannot be
used for a rack position.
Guide
3 3
2 2
1 1
Always place oven racks in the
proper position while oven is
cool.
FLAT COOKIE SHEETS, without
sides, allow air to circulate all around
the cookies for even browning.
You may feel that your new oven cooks
differently than the oven it replaced. We
recommend that you use your new oven
a few weeks to become more familiar
with it, following the times given in your
recipes as a guide. See Do It Yourself
Temperature Adjustment in the back of
this manual to make the adjustment if
you feel your oven is too hot or too cool
11 for your cooking preference.

OPERATION
Baking
(_ 1. Press the BAKE
pad.
(_ 2. Press the TEMP UP
and/or DOWN arrow
TEMP pads to set the oven
temperature you
prefer to use.
3. Press the STARTpad.
To set the oven to cook for a specific
time and turn off automatically.
(_ 1, Press the BAKEpad.
2. Press the TEMP UP
and/or DOWN arrow
TEMP pads to set the oven
temperature you
prefer to use.
3. Press the OVEN
COOKING TIME
pad.
_4.Press the HOURI
MIN UP and/or
HOUR MIN DOWN arrow pads
(_ (_ to set the amount of
time you prefer your
foods to cook.
5. Press the START
pad.
To set the oven to turn on at a later
time of day, cook for a specific
amount of time and turn off automati-
cally.
(_ 1. Press the BAKEpad.
(_ 2. Press the TEMP UPand/or DOWN arrow
TEMP pads to set the oven
temperature you
prefer to use.
3. Press the OVEN
COOKING TIME
pad.
(_) (_) 4, Press the HouR/
MIN UP and/or
HOUR MIN DOWN arrow pads
_ @ tosettheamountof
time you prefer your
foods to cook.
5. Press the DELAY
START TIME pad.
_6. Press the HOUR/
MIN UP and/or
HOUR MIN DOWN arrow pads
_ to set the time of day
you prefer the oven
to turn on.
7. Press the STARTpad.
These oven operations may be
used when roasting.
The oven will cut off at the end of the
cooking time unless the cook and
hold feature has been activated.
12

OPERATION
Broiling
Broiling is cooking by direct heat
from the upper element. The oven
door should remain open to the broil
stop position during broiling.
It is not necessary to preheat the
oven when broiling. Use the broiler
pan and grid that came with your
oven. Both are designed for proper
drainage of fat and liquids.
If foil is used it must
be molded tightly to
the grid and slits cut
into the foil to match
those of the grid. This
allows fats end liquids to
drain into the broiler pan,
preventing fire and
excessive smoke.
Always remove the pan and
grid from the oven. r_
Storing or forgetting
a soiled broiler pan
in the oven is a potential
smoke or fire hazard.
k
The U.S. Department of Agriculture
recommends to cook meat and
poultry thoroughly--meat to at least
an INTERNAL temperature of 160° F
and poultry to at least an INTERNAL
temperature of 180" F. Cooking to
these temperatures usually protects
against food-borne illness,
The closer you place foods to the
broil element, the faster foods brown
on the outside yet remain red to pink
in the center.
Moving meats away from the element
will allow the meat to cook to the
center while browning on the outside
Cook side 1 at least 2minutes longer
than side 2. If your oven is connected
to 208 volts, you may want to use a
higher rack position and/or broil
foods longer.
The size, weight, thickness, starting
temperature and your preference of
the doneness of the meat will affect
broiling. This chart is based on meats
at refrigerator temperature.
FOOD
Steak 1" thick
Ground beef
patties
1" thick
Pork Chops -
1/2" thick
Fish Ifllletsl
Chicken (pieces I
RACK TOTAL
POSITION TIME (MIN. I
3 9-11
3 16-18
3 27-29
3 11-13
2 45-55
la. Press the BROIL pad (This
will automatically set HI
Broil).
lb. While the set indicator is flashing
in the display, press the BROIL
pad again if you prefer to use Lo
Broil, Use Lo Broil to cook foods
such as poultry or thick cuts of
meat thoroughly without over-
browning them.
2. Press the START pad.
3. When broiling is finished, press
the CLEAR/OFF pad.
13

OPERATION
Setting Special Features
Your new touch pad control has
additional features that you may choose
to use. After making your selection, if
you want to change that setting, follow
the steps until the display shows your
choice.
The control is automatically set to turn
off the oven after 12 hours baking or 3
hours broiling should you forget and
leave the oven on. If you want to
remove this feature:
1. Press and hold, at the same
time, the BAKE and BROIL pads
for 3 seconds, until the display
shows SF.
2. Press the DELAY START TIME
pad. The display shows 12shdn
(12 hour shut-off).
Press the DELAY START TIME
pad again. The display will show no
shdn (no shut-off).
3, Press the START pad.
Your oven control is set for the
Fahrenheit temperature selections. Most
recipes are given using the Fahrenheit
scale. You can change this to use the
Celsius selection.
1, Press and hold, at the same
time, the BAKE and BROIL pads
for 3 seconds, until the display
shows SF.
2. (a) Press the BROIL pad. The
control display will show the
degrees sign and F.
(b) Press the BROIL pad again,
This will change F(Fahrenheit) to C
(Celsius).
3. Press the START pad.
Your control is set to use the 12 hour
clock. If you prefer to use the 24 hour
Military Time clock or black out the
display:
1. Press and hold, at the same
time, the BAKE and BROIL pads
for 3 seconds, until the display
shows SF.
2. (a) Press the CLOCK pad. The
display shows 12hr. If this is your
choice press the START pad.
or
(b) Press the CLOCK pad again.
The display will show 24hr.
Example: 5:00 on the 12 hour clock
will show 17:00 hours on the military
clock If this is your choice press the
START pad.
or
(c) Press the CLOCK pad again.
The display will show OFF. If this is
your choice press the START pad.
The display will not show time. (The
Delay Start Time feature will not
operate.)
14

OPERATION
Setting Special Features
Your control will allow you to lock the
touch pads so they cannot be activated
when pressed. If you're'worried about
;eaving the oven unsupervised, activate
this feature.
1, Press and hold, at the same
time, the BAKE and BROIL pads
for 3 seconds, until the display
shows SF.
2. (a) Press the CLEAN pad. The
display shows LOC OFF (lockout
off).
(b) Press the CLEAN pad again
The display will show LOC ON
(lockout on).
3. Press the START pad.
This feature can only be set
when the oven is not In use.
When this feature is on, the display will
show LOC, if a touch pad is pressed.
(This feature will not affect the Clock,
Timer or Oven Light pads.)
Your new control hasa cook and hold
feature for timed cooking only that will
keep hot cooked foods warm up to 3
hours after the timed cooking is
finished. To activate this feature:
1. Press and hold, at the same
time, the BAKE and BROIL pads
for 3 seconds, until the display
shows SF
2. (a) Press the OVEN COOKING
TIME pad. The display will show
HLd OFF.
(b) Press the OVEN COOKING
TIME pad again to activate the
feature, The display will show HLd
ON.
3. Press the START pad.
This special feature wil! allow you to
change the speed; #1 means speed of
change is slow up to #5 which means
speed of change is fast, To set the
speed you prefer, follow these steps:
1. Press and hold, at the same
time, the BAKE and BROIL pads
for 3 seconds, until the display
shows SF
2. Press the UP arrow pad. The
display will show the current set
speed.
3. Press the UP arrow to increase the
speed up to the number 5.
or
Press the DOWN arrow pad to
decrease the speed down to the
number 1.
4. Press the START pad.
15

Self-Cleaning Cycle CAREANDCLEANING
1. Remove the broiler pan and grid,
oven racks, utensils and any foil
that may be in the oven.
2. Soil on the front frame,l" inside
the oven, and outside the door
gasket will need to be cleaned
by hand.
Front Frame
Door Liner
Clean these areas with hot water,
soap-filled steel wool pads or
cleansers such as Soft Scrub ®to
remove any soil, Rinse well with clean
water and dry.
3. Wipe up any heavy spillovers on
the oven bottom.
4. Do not clean the door gasket. The
fiberglass material of the oven
door gasket cannot withstand
abrasion. It is essential for the
gasket to remain intact If you
notice it becoming worn, frayed or
displaced on the door, it should be
replaced.
The door gasket is designed to have
a 5-6" gap at the bottom of the door.
This allows for proper air circulation.
Door Panel Gasket
It is normal for your oven door to give
the appearance of not having a good
seal against the oven, This is due to
the gasket. The location of the gasket
on the oven door maintains a good
seal and prevents any heat loss.
Utensils should never
I _1 be left in the oven
during a self-clean
cycle.
The oven racks may be
cleaned daring the
self-clean cycle, but will
lose their luster and become
hard to slide, if you choose
to leave them in during the
cycle, wiping them down
with vegetable oil after the
cycle will help them slide
easier.
For the first clean cycle,
vent the room with an
opened window or hood
vent. This will reduce the
odor when heating new
_parts.
16

CAREANDCLEANING
Self-CleaningCycle
The Clean Cycle, including cool down
time, is automatically set for 4 hours,
but you may change this from 3 hours
if oven is lightly soiled, up to 5 hours if
oven is heavily soiled.
(_ 1. Press the CLEAN
pad. 4 hours will
show in the display.
(_ (_ 2. If you want to
change the length of
HOUR MIN clean time press the
_ _ HOUR/MINUPand/or DOWN
arrow pad.
3. Press the STARTpad.
Simply press the CLEAR/OFF pad.
You will need to wait for the oven
temperature to drop below the lock
temperature (approx. 1 hour) before
attempting to open the door.
After the cycle, you may notice some
white ash in the oven, Just wipe it up
with a damp cloth or sponge.
If white spots remain, scrub them
with a soap-filled steel wool pad. Be
sure to rinse thoroughly. These are
usually deposits of salt that cannot
be removed during the cycle.
If for any reason you are not
satisfied with the cleaning
results, just repeat the cycle.
HOUR MIN
@@
HOUR MIN
@@
1. Press the CLEAN
pad.
2. If you want to
change the length
of clean time
press the HOUR/
MIN UP and/or
DOWN arrow
pads.
3. Press the DELAY
START pad.
4. Press the HOURI
MIN UP and/or
DOWN arrow
pads to set the
time you prefer the
clean cycle to
start.
5. Press the START
pad.
17

CAREANDCLEANING
Removable Parts
CLEANING MATERIALS
• Dishwashing detergent
•Warm water
• Soft cloth
Do not use abrasive cleaners,
industrial cleaners or bleach.
CLEANING MATERIALS
• Dishwashing detergent
• Warm water
• Soap-filled scouring pad
• Commercial oven cleaner
TO CLEAN
Allow the pan to soak. Sprinkle the
grid with dishwashing detergent and
cover with a damp cloth or paper
towel. Rinse and dry well. Scour as
needed. You may also place both the
pan and grid in the dishwasher.
Clean only as touch up between clean
cycles. Use dishwashing liquid, warm
water, or a soap-filled steel wool pad.
Rinse well after cleaning and dry.
NEVER USE OVEN CLEANERS
IN OR AROUND ANY PART OF
THE OVEN.
When cleaning, be sure not to bend or
displace the temperature sensor
located on the back wall of the oven.
CAUTION: Disconnect
electrical power to
the oven at the main
circuit breaker or fuse box
before attempting to replace
the oven light bulb. Do not
touch a hot light bulb with
wet hands or a wet cloth.
Wait until the bulb has
cooled and use a dry cloth.
Bulb Live r_ S°cket
Colla_
Bulb Cover Bail Wire
TO REMOVE THE COVER
1. Disconnect electrical power to the
oven at the main circuit breaker or
fuse box.
2. Hold your hand under cover and
firmly push back the bail wire, until it
clears and releases the bulb cover.
REPLACE THE LIGHT BULB
Unscrew the light bulb and replace it
with a40-watt appliance bulb.
TO REPLACE COVER
t. Place the bulb cover into the groove
of the bulb socket.
2. Pull the bail wire forward until it
snaps into the indentation on top of
the bulb cover.
3, Reconnect the electrical power to
the oven.
18

CAREANDCLEANING
Removable Parts
Broil Stop Position
CLEANING MATERIALS
•Dishwashing detergent
• Warm water
• Scouring pad or soap-filled steel wool
pad
Bump In
Rack Guide,
Raised Back
TO REMOVE
1. Pullthe racks out to the stop lock
position.
2. Pull up the front of the rack and
slide under the bump of the rack
guide.
TO CLEAN
Clean with warm water and detergent.
For hard to remove stains, gently scrub
with a scouring pad or a soap-filled
steel wool pad. Rinse well.
TO REPLACE
1. Place the raised back of the rack
onto the rack guides.
2. Lift the front of the rack until the
raised back slides under the bump
of the rack guides.
3, Slide the rack all the way back.
Hinge
TO REMOVE
1. Open the door to the broil stop
position.
2. Grasp the door at each side and lift
up and off the hinges. DO NOT
LIFT DOOR BY THE HANDLE.
_CAUTION: When
the door is removed
and the hinge arms
are at the broil stop
position, as a precaution,
cover the hinge arms with
toweling or an empty paper
towel roll. Do not bump or
try to move the hinge arms
while working in the oven
area. They could snap back
causing injury to the hands
or damage the porcelain
finish of the front frame.
TO REPLACE
1. Make sure the hinge arms are in the
broil stop position.
2. Lift the door by the sides
3, Line up the slots at the bottom edge
of the door with the hinge arms.
4, Slide the door down onto the hinge
arms as far as it will go.
5. Close the door.
19

BEFORECALLINGFORSERVICE
Tosave you time and money, before making a service call check the list below for any
problem you may feel you have with the performance of your oven. If the problem is
something you cannot fix use theConsumer Service Numbers located at the back of this
manual. When making any calls have the Model No., Repair Parts list,
Use and Care Manual and the Date of Purchase available.
PROBLEM POSSIBLE CAUSE POSSIBLE SOLUTION
The display of your
control is flashing
"F" followed by a
number or letter.
Oven malfunction. Press the CLEAR/OFF
pad. Let the oven cool for
1hour and enter an oven
or cleaning operation. If
code repeats, call for
service.
Oven and oven
control will not
work.
No power to oven.
The clock is in the
black-out mode.
Check the circuit breaker
or fuse. Make sure the
power cord is plugged in.
See the "Setting Special
Features" section of this
manual.
Oven temperature Thermostat calibration. See the adjustments
seems inaccurate, described following this
section.
Oven will not Clean cycle is not
unlock, finished Oven temperature must
drop below the lock
temperature before the
door will unlock.
Oven light will not
work. a. Light switch in off
position.
b. Oven light bulb
burned out.
a. Check oven light
switch on the control
panel,
b, Check the oven light
bulb.
Oven did not
clean or results
were poor.
a. Controls were not set
properly,
b. Clean cycle was
interrupted.
c. Oven was soiled
heavily.
2O
a. Check the self-cleaning
section of this manual.
bo The normal clean cycle
should last 4 hours.
c, Heavy spillovers
should be removed
before the cycle is set.
You can also repeat
the cycle.