Kenmore 116.31040 User manual

Use & Care Guide
Manual de Use ¥ Cuidado
English/Espa_ol
116.31040
O
P/N C01ZDNS20UO_ - J<C_IZDNS2_U_
Sears Brands Management
Corporation, Hoffrnan Estates,
IL 60179 U.S.A
www.kenmore.corn
www.sears.corn

Before Using Your New
Vacuum Cleaner .................. 2
Packing List .................... 2
Vacuum Cleaner Help Line .......... 3
I(enmore Vacuum Cleaner Warranty . . 3
important Safety Instructions ........ 4
Parts and Features ................ 5
Assembly Instructions .............. 6
Handle ........................ 6
Attachment Assembly ............ 7
Power Cord .................... 8
Operating instructions .............. 9
Power Cord .................... 9
Releasing the Handle ............ 10
OFF/FLOOR/CARPET Switch ..... 10
Pile Height Selection ............. 11
Attachments ................... 12
Attachment Use Table ........... 13
Vacuuming Tips ................ 13
Performance/Safety Features ..... 14-15
Vacuum Cleaner Care ............. 16
Vacuum Cleaner Storage ........ 16
Cleaning Exterior and Attachments .16
Dust Cup Emptying ............. 17
Dust Cup Cleaning .............. 18
Pre-Filter Cleaning .............. 19
Primary and Secondary Filter
Cleaning ...................... 20
Exhaust Filter Replacement ....... 21
Agitator Cleaning .............. 21
Clog Removal .............. 22-23
Troubleshooting .................. 24
Master Protection Agreements ...... 25
Requesting Assistance
Or Service ................ Back page
Please read this guide. It will help you assemble and operate your new Kenmore vacuum
cleaner in the safest and most effective way.
For more information about vacuum cleaner care and operation, call your nearest Sears Parts
and Repair Center or the Vacuum Cleaner Help Line listed on the cover of this guide. You will
need the complete model and serial numbers when requesting information. Your vacuum
cleaner's model and serial numbers are located on the Model and Serial Number Plate.
Use the space below to record the model numberand serial number of your new Kenmore
vacuum cleaner.
Model No.
Serial No.
Date of Purchase
Keep this book and your sales check (receipt) in a safe place for future reference.
PACKING LiST
Your KENMORE VACUUM CLEANER ispackaged with the following parts and compo-
nents assembled separately in the carton:
1 Upright Vacuum Cleaner 1 Pet Handi Mate TM
1 Handle 1 Telescoping Wand
1 Crevice Tool 1 Use & Care Guide
1Combination Brush 1 Repair Parts List
Each of the above assemblies are shown in detail inside the Repair Parts List.
-2-

Vacuum Cleaner Help Line:
| -877-53| -732|
One Year Limited Warranty
8:00am-5:OOpm EST,M-F
(U.S.A. and Canada)
When assembled, operated and maintained according to all instructionssupplied with
the product, if this vacuum cleaner fails due to a defect in material or workmanship
within one year from the date of purchase, return it to any Sears store, Sears Parts &
Repair Center or other I<enmore outlet for free repair.
If this vacuum cleaner is used for other than private family purposes, this warranty
applies for only 90 days from the date of purchase.
Thiswarranty covers only defects in material and workmanship. Sears will NOT pay
for:
1. Expendable items that can wear out from normal use, including but not limited to
filters, belts, light bulbs, and bags.
2. A service technician to instruct the user in correct product assembly, operation or
maintenance.
3. A service technician to clean or maintain this product.
4. Damage to or failure of this product if it is not assembled, operated or maintained
according to all instructions supplied with the product.
5. Damage to or failure of this product resulting from accident, abuse, misuse or use for
other than its intended purpose.
6. Damage to or failure of this product caused by the use of detergents, cleaners,
chemicals or utensils other than those recommended in all instructions supplied with
the product.
7. Damage to or failure of parts or systemsresulting from unauthorized modifications
made to this product.
Disclaimer of implied warranties; limitation of remedies
Customer's sole and exclusive remedy under this limited warranty shall be product
repair as provided herein. Implied warranties, including warranties of merchantability or
fitness for a particular purpose, are limited to one year or the shortest period allowed
by law. Sears shall not be liable for incidental or consequential damages. Some states
and provinces do not allow the exclusion or limitation of incidental or consequential
damages, or limitations on the duration of implied warranties of merchantability or
fitness, so these exclusionsor limitations may not apply to you.
This warranty applies only while this vacuum cleaner isused in the United States and
Canada.
This warranty gives you specific legal rights, and you may also have other rights which
vary from state to state.
Sears, Roebuck and Co., Hoffman Estates, IL 60179
Sears Canada Inc., Toronto, Ontario, Canada M5B 2B8
-3-

Read all instructionsin this guide before assembling or using your vacuum cleaner.
WARNING:
Your safety is important to us. To reduce the risk of fire, electrical shock, injury to per=
sonsor damage when using your vacuum cleaner, follow basic safety precautions in-
cludlng the following:
Use your vacuum cleaner only as de-
scribed in this manual. Use only with
Sears recommended attachments.
Disconnect electrical supply before serv-
icing or cleaning out the brush area.
Failure to do so could result in the brush
unexpectedly starting, causing personal
injury from moving parts.
Do not leave vacuum cleaner when
plugged in. Unplug from outlet when
not in use and before performing main-
tenance.
To reduce the risk of electrical shock -
Do not use outdoors or on wet surfaces.
Do not allow to be used as a toy. Close
attention is necessary when used by or
near children.
Do not use with a damaged cord or
plug. if vacuum cleaner is not working
as it should, has been dropped, dam-
aged, left outdoors, or dropped in
water, return it to a Sears Service Center
for assessment before using again.
Do not pull or carry by cord, use cord
as a handle, close adoor on cord, or
pull cord around sharp edges or corners.
Do not run vacuum cleaner over cord.
Keep cord away from heated surfaces.
Do not unplug by pulling on cord. To un-
plug, grasp the plug, not the cord.
Do not handle plug or vacuum cleaner
with wet hands.
Do not put any objects into openings.
Do not use with any opening blocked;
keep free of dust, lint, hair, and anything
that may reduce air flow.
Keep hair, loose clothing, fingers, and
all parts of body away from openings
SAVE THESE
and moving parts.
Turn off all controls before unplugging.
Use extra care when cleaning on stairs.
Do not put on chairs, tables, etc. Keep
on floor.
Do not use vacuum cleaner to pick up
flammable or combustible liquids (gaso-
line, cleaning fluid, perfumes, etc.), or
use in areas where they may be present.
The fumes from these substances can
create a fire hazard or explosion.
Do not pick up anything that is burning
or smoking, such as cigarettes, matches,
or hot ashes.
Do not use vacuum cleaner without dust
cup and/or riflers in place.
Always clean the dust cup after vacu-
uming carpet cleaners or freshener,
powders, and fine dust. These products
clog the filters, reduce airflow and can
cause damage to the vacuum cleaner.
Failure to clean the dust cup could
cause permanent damage to the vac-
uum cleaner.
Do not use the vacuum cleaner to pick
up sharp hard objects, smalt toys, pins,
paper clips, etc. They may damage the
vacuum cleaner or dust cup.
Unplug before connecting Pet Handi
Mate TM
You are responsible for making sure that
your vacuum cleaner is not used by any-
one unable to operate it properly.
iNSTRUCTiONS
Proper assembly and safe use of your vacuum cleaner are your responsibilities. Your
vacuum cleaner isintended for Household use.Read this Use & Care Guide carefully for
important use and safety information. This guide contains safety statementsunder
warning and caution symbols.
-4-

it isimportant to know your vacuum cleaner's parts and features to assure its proper and safe
use. Review these before using your vacuum cleaner.
Object Style No. Part No. Part No.
in USA in Canada
Exhaust Filter EF-1 20-86889 20-40324
Handle
OFF/FL OOR/CARPET
Switch
Cord
Hose
Dust Cup
Release
Quick Release
Cord Hook----_
Pet
Agitator
Reset
-Exhaust
Filter Cover
(Filter Inside)
Carry
Primary
Filter Cover
Combma#on
Brush
Handle
Release
Pedal_
Hose
Release
Tool
Wand
Wand
Holder
Headlight
Model/Serial
Numbers Hose
-5-

Please pay special attention to these hazard alert boxes, and follow any instruc-
_ tions given. WARNING statements alert you to such hazards as fire, electric
shock, burns and personal injury. CAUTION statements alert you to suchhazards
as personal injury and/or property damage.
_WARNING
Electrical Shock Hazard
Do not plug vacuum cleaner into the
electrlcal supply untll the assembly is
complete. Failure to do so could result
in eletrlcal shock or injury.
Before assembling the vacuum cleaner,
check the PACKING LIST. Use this list to
verify that you have received all the
components of your new Kenmore
vacuum cleaner.
HANDLE
CAUTION
Do not overtlghten handle screw.
Overtightening could strip the screw
holes.
Do not operate the vacuum cleaner
without the screw in place.
1. Remove the handle screw from the
body of the vacuum cleaner.
2. Position the handle assembly as shown
in the illustration.
3. Using a screwdriver, tighten handle
screw,
NOTE: It may be necessary to adjust the
handle slightly.
Scyew
Hole,
Handle
Screw
-6-

ATTACHMENT ASSEMBLY
HOSE AND WAND
1. Insert the tab on Hose "_
the telescopic wand Handle_\\ 1
into the "J" slot on the
hose handle. Twist "J"Slot
the telescopic wand _-_-,_
to lock in place. ,_
'2. Place the tele- t_
scopic wand in the
wand holder and Telescopic
route the hose as Wand_--4
shown, J
Raised
Edge Hose I
Handle-
3. Snap the
hose handle
into the hose
holder located
on the handle
of the vacuum
cleaner.
NOTE: Be sure
the raised edge
of the hose
handle rests
against edge of
the hose holder.
4. Rotate the
hose release
lever down
and route the
hose as
shown.
5. Snap the
hose into the
hose cuff on
the side of
the vacuum
cleaner
Hose
Telescopic
Wand
Hose
Release
Lever-_-__
6. Rotate the hose
release lever
upwards to lock
the hose in place.
_L, CAUTION
Do not operate the agitator without
the wand property inserted into the
wand holder and the hose handle
properly secured in the hose holder
-7-

PET HANDI MATE TM
For operation of Pet Handi Mate TM see
separate Use & Care Guide.
1. Place Pet
Handi Mate TM
into the storage
area.
'2. Rotate the Pet
Handi Mate TM
back until it
snaps into place.
Pet
Handi Mate TM
CREVICE TOOL
1. Insert the
crevice tool into
the holder on the
side of the vac-
uum cleaner as
shown.
COMBINATION BRUSH
1. Insert the
combination
brush into the
holder on the
back of the
vacuum
cJeaner as
shown.
POWER CORD
1. Make sure that cord hook is in upright
position as shown.
2. Wrap power cord loosely around cord
hook and carry handle.
3. Lock power cord plug onto the power
cord.
_WARNING
Electrical Shock and Personal injury
Hazard
Wrapping the cord too tightly putsstress
on the cord and can cause cord dam=
age. A damaged cord is an electrical
shack hazard and could cause personal
injury or damage.
Power
Cord
Carry
-8-

_CAUTION
Moving parts! To reduce the risk of personal injury,
DO NOT touch the agitator when vacuum cleaner
is on. Contacting the agitator while it is rotating can
cut, bruise or cause other injuries. Always turn off
and unplug from electrlcal outlet before servlclng.
Use cautlon when operatlng near children.
\
1. Turn the quick
release cord
hook to either
side and down to
release the
power cord.
WARN ING
" To reduce the risk of electric shock,
this vacuum cleaner has apolarized
plug (one blade is wider than the
other).
*The plug will fit in apolarized outlet
only one way. If the plug does not
fit fully in the outlet, reverse the
plug. If it still does not fit, contact a
qualified electrician to install the
proper outlet. Do not change the
plug in any way.
2. Detach the
power cord plug
from the power
cord and pull the
cord off the
quick release
cord hook.
Locking_
3. Be sure the power cord is locked into
the locking notch of the quick release
cord hook.
POWER CORD j
4. Plug the polarized power cord into a
120 Volt outlet located near the floor.
_WARNING
Personal injury and Product Damage
Hazard
* When any abnormality/failure
occurs,stop using the product
immediately and disconnect the
power plug.
DO NOT use outlets above counters.
Damage from cord to items in
surrounding area could occur.
5. To store cord, turn the quick release
cord hook to the up position, then wrap
cord loosely around quick release cord
hook and carry handle.
_kWARNING
Electrical Shock And Personal injury
Hazard
Wrapping the cord too tightly puts stress
on the cord and can cause cord dam-
age. A damaged cord is an electrical
shock hazard and could cause personal
injury or damage.
-9-

RELEASING THE HANDLE
Release the handle by pressing down on
the handle release pedal with your foot
and pulling back and down on the handle
with your hand.
Note: The agitator does not rotate when
the vacuum cleaner is in the upright posi-
tion.
\
OFF/FLOOR/CARPET SWITCH
To start the vacuum cleaner, slide the
OFF/FLOOR/CARPET switch from the OFF
_osition to the FLOOR or CARPET
_osition.
CAUTION
Refer to your carpet manufacturers
cleaning recommendations. Some
more delicate carpets may require that
they be vacuumed with the agitator
turned off, to prevent carpet damage.
To stop the vacuum cleaner, slide the
ON/FLOOR/CARPET switch to the OFF
position.
CAUTION
Do not allow vacuum cleaner to re-
main in one spot for any length of time
when the agitator is turning. Damage
to carpet may occur.
OFF - turns OFF/FLOOR/
both suction CARPET
and brush Switch-_h
motors off. Selector
FLOOR - turns
on the suction
motor only. In
this position
the agitator
does not
revolve. Use this setting for cleaning
hardwood and tile floors and when any
attachments (tools) ore used.
CARPET - turns on both the suction and
the brush motors.
Note: The agitator does not rotate when
the vacuum cleaner is in the upright
position.
-10-

PILE HEIGHT SELECTION
To select a pile height setting:
Turn off vacuum cleaner. Select a pile
height setting by tilting the vacuum
cleaner back until front wheels are lifted
slightly off the floor.
Slide the adjustment lever to the correct
setting.
There are four (4) pile height settings on
the vacuum cleaner. Use the LOW setting
for most low-pile carpets and bare floor
cleaning (with agitator OFF), and the
HIGH setting for high-pile carpets like
shag carpet, scatter rugs, etc. Use the
other settings as needed for carpet
heights in between.
CAUTION
Refer to your carpet manufacturers
cleaning recommendations. Some
more delicate carpets may require
that they be vacuumed with the
agitator turned off, to prevent
carpet damage.
-11-

ATTACHMENTS
CAUTION
DO NOT use the hose when vacuum
cleaner handle istilted back into the floor
cleaning position.
Always return the vaccum cleaner to the
upright position before using the hose and
attachments.
Failure to do so may result in overheating
of the agitator motor and can cause the
thermal protector to trip
TO USE ATTACHMENTS
1. Place the vacuum cleaner in the
upright position.
'2. Remove the hose handle and wand by
removing hose handle from hose holder
and lifting up.
Hose
Hose
3. Use attachments as needed. See
ATTACHMENT USE TABLE.
FOR ADDiTiONAL REACH
Rotate hose
release lever
down to release
hose for
maximum hose
reach.
CAUTION
When using attachments, be careful
not to overextend the stretch hose
when reaching. Trying to reach be-
yond the hose stretch capability could
cause the vacuum cleaner to tip over.
_CAUTION
DO NOT pull the vacuum cleaner
around the room by the hose. Prop-
erty damage or personal injury could
result.
TELESCOPING WAND
1. The wand length
is adjustable and
requires no
assembly. To adjust,
simply press the
wand button and
slide the wand to
the desired height.
'2. Release button
and continue to
slide wand until it
locks into position.
COMBiNATiON BRUSH
The combination brush can be attached
directly to the wand.
Combination _
Brush Brush2 \__)
Holder
Use the brush holder without the brush for
greater suction on furniture cushions or
stairs.
Use brush holder with brush for cleaning
loose surfaces such as drapes.
-12-

ATTACHMENT USE TABLE
CLEANING AREA
ATTACHMENT Between
Furniture_Cushions_ Drapes _ Stairs Walls
CREVICE TOOL _ i/ v' v'
v' v' v' v'
COMBINATION BRUSH
PET HANDI MATE TM t/
= Applicable
Always clean attachments before using on fabrics and walls.
_ Use the brush holder without the brush for greater suction on furniture cushions or stairs.
Use brush holder with brush for cleaning loose surfaces such as drapes.
Carpet edges
Guide either side or the front of the
nozzle along the walt baseboard.
Stairs
Set handle in full upright position. The
agitator stops rotating automatically. Use
the crevice tool, combination brush or Pet
Handi Mate TM.
Unit Tipping
When using the attachments keep the
hose release lever in the locked position
when possible. This helps to keep the
vacuum cleaner from tipping over when
stretching the hose. If additional hose is
needed then unlock the hose release lever
and pull out additional hose. Use caution
not to tip over vacuum cleaner.
WARN ING
Personal Injury Hazard
Use care if vacuum cleaner is placed
on stairs. If it falls, personal injury or
property' damage could result.
For best cleaning resultsn keep the airflow
passage clear. Unplug the vacuum
cleaner from the outlet before checking.
See CLOG REMOVAL section of this Use &
Care Guide.
-13-

MOTOR PROTECTION SYSTEM
Thermal Protector - Suction Motor
This vacuum cleaner has a thermal
protector which automatically trips to
protect the vacuum cleaner suction motor.
If aclog prevents the normal flow of air
to the motor, the thermal protector turns
the motor off automatically. This allows
the motor to cool in order to prevent
possible damage to the vacuum cleaner.
Thermal Protector - Agitator Motor
This vacuum cleaner has a thermal
protector which automatically trips to
protect the agitator motor. The thermal
protector turns the motor off
automatically. This allows the motor to
cool in order to prevent possible damage
to the vacuum cleaner.
To reset thermal protector: Turn the
vacuum cleaner off and unplug the power
cord from the outlet to allow the vacuum
cleaner to cool and the thermal protector
to reset.
_CAUTION
Always return the vaccum cleaner
to the upright position before using
the hose and attachments. Failure
to do so may result in overheating
of the agitator motor and can
cause the thermal protector to trip.
Check for and remove clogs, and replace
bag if necessary. See CLOG REMOVAL
section. Also check and replace any
clogged filters. Wait approximately 40=
50 minutes before restarting vacuum
cleaner.
-14-

AGITATOR OVERLOAD
PROTECTOR
The agitator has built-in protection
against motor damage should the
agitator jam. If the agitator slows down
or stops, the agitator overload protector
shuts off the agitator motor. The vacuum
cleaner suction motor will continue to run.
Agitator
Reset
WARNING
Electrical Shock And Personal Injury
Hazard
Disconnect electrical supply before
performing maintenance to the vacuum
cleaner. Failure to do so could result in
electrical shock or personal injury from
vacuum cleaner suddenly starting.
Tocorrect problem: Turn off and unplug
vacuum cleaner, remove obstruction, then
press AGITATOR RESETBUTTON.
NOTE: A MiNiMUM OF 20 SECONDS
NEEDS TO PASSBEFORE RESETTING
OVERLOAD.
If the problem persists, have the vacuum
cleaner serviced by a Sears or other
qualified technician.
-15-

Always follow alt safety precautions when
performing maintenance to the vacuum
cleaner. WARNING
Electrical Shack And Personal injury
Hazard
Disconnect electrical supply before
servicing or cleaning the vacuum
cleaner. Failure to do so could result
in electrical shock or personal injury
from vacuum cleaner suddenly
starting.
VACUUM CLEANER STORAGE
Gather the cord
and wrap it
loosely around
the quick re-
lease upper
cord hooks and
carry handle.
Lock power
cord plug onto
the power cord.
Store the vac-
uum cleaner in
adry, indoor
area r on the
floor with the
handle locked
in the upright
position.
Power Cord--
Quick Release
Carry
,_WARNiNG
Electrical Shock And Personal injury
Hazard
Wrapping the cord too tightly puts stress
on the cord and can cause cord dam=
age. A damaged cord is an electrical
shock hazard and could cause personal
injury or damage.
CLEANING EXTERIOR AND ATTACHMENTS
Unplug cord from wall outlet.
Clean exterior using a clean, soft cloth
that has been dipped in a solution of mild
liquid detergent and water, then wrung
dry. DO NOT drip water on vacuum
cleaner. Wipe dry after cleaning.
To reduce static electricity and dust build-
up, wipe outer surface of vacuum cleaner
and attachments.
Wash attachments in warm soapy water,
rinse and air dry. Do not dean in dish=
washer.
CAUTION
Do not use attachments if they are
wet. Attachments used in dirty areas,
such as under arefrigerator, should
not be used on other surfaces until
they are washed. They could leave
marks.
-16-

DUST CUP EMPTYING
WARNING
Always unplug power cord from
electrical outlet before performing
any service on vacuum cleaner.
TO REMOVE DUST CUP
Lift dust cup
handle located
at the top of the
dust cup.
Pull the handle
up and lift dust
cup up and out
of the vacuum
cleaner.
Dust Cup /_
Filter Remove any
clogs that might
be located in the
suction port or
filter port area,
TO EMPTY DUST CUP
1. Rotate dust
cup handle to {J_-.
the vertical
position.
2. Hold dust
cup over a
trash container.
3. Pressthe
dust cup door
release button
downward to
release the
door.
The door wilt
swing open
and the debris
will fall into the trash container.
4. Shake the dust cup to release any
debris that might hang in the pre-filter.
5. After the
dust cup is
empty of
debris, firmly
close the door,
Make sure you
hear a "click"
sound to
indicate that
the door is fully
latched,
Door Door
Latch
TO REPLACE DUST CUP
Place dust cup back
into vacuum cleaner
by inserting the
bottom first and
tilting back with the
dust cup handle
raised.
LLower the
dust cup
handle to
lock dust cup
in place.
A noticeable
"click" should
be heard,
-17-

DUST CUP CLEANING
TO ASSEMBLE DUST CUP
TO DISASSEMBLE DUST CUP
Remove dust cup from vacuum cleaner
(See DUST CUP EMPTYING) and empty
contents.
1. Rotate upper dust
cup to unlock, then
lift off.
'2. Remove pre-filter by
pulling downward as shown.
See PRE-FILTER CLEANING
3. Press the lid
release button
downward and
twist lid to remove
from dust cup.
4. Rotate fastener ring
to unlock,and lift off.
5. Remove upper
portion of dust cup
from air guide.
6. Rinse with cold
water only, DO NOT
use detergent or soap.
Allow parts to dry 24
hours before putting
back into vacuum
cleaner.
DO NOT wash in the
dishwasher.
DO NOT install parts
damp.
1. Reinstall upper
portion of dust cup
onto air guide so
that the locking
screws pass
through the
holes inthe
upper portion,
;!:_i_iI!!.....
'2. Using alignment marks
on the fastener ring and
dust cup, place fastener
ring onto dust cup and
rotate to lock in place.
3. Place the dust cup
lid on the upper
portion of the dust cup
using aligniment slots,
and rotate until the lid
locks in place.
should be heard.
I 4. Reinstall pre-filter
by using the
alignment ribs on the
pre-fitter to align with
the ribs on the upper
portion of the dust
cup.
5. Press into place. A
noticeable "click"
6. Reinstall lower
portion of the dust cup
by aligning ribs on the
upper portion with the
UNLOCK ribs on the
lower portion.
Z Rotate until ribs
from the upper portion of the dust cup
align with the LOCI< ribs.
NOTE: If lower portion of dust cup does
not fit properly check pre-filter
installation in step 4.
-18-

PRE-FILTER CLEANING
The pre-fitter is located inside the dust
cup. Check the pre-filter frequently and
cleon when dirty.
1. Remove the dust cup as outlined in the
DUST CUP CLEANING section.
NOTE: Make sure dust cup is free of de-
bris before opening.
2. Rotate dust cup lid assembly counter-
clockwise as indicated on the lid and lift
off.
LOCKED
(ForUs_
UNLOCKED
(ForCleanm_
3. Clean pre-
filter by gently
tapping over o
trash
container. Top
on several
sides to ensure
best cleaning.
If necessary,
rinse with cold
water only,
DO NOT use
detergent or
soap. Allow
parts to dry
LJ
.(__ Pre-FIIter
24 hours before putting back into vacuum
cleaner.
DO NOT wash in the dishwasher.
DO NOT install damp.
4. Replace the lower portion of the dust
cup by aligning marks as shown,
UNLOCKED (For Cleaning).
5. Rotate while pressing downward until
marks align as shown; LOCKED (For Use).
6. Replace the dust cup.
-19-

PRIMARY FILTER AND SECONDARY FILTER CLEANING
It is recommended to clean the primary
fitter with cold water at least every three
(3) months.
Check the primary filter frequently and
clean when dirty.
Rear
1. Remove the
rear cover by
pressing the tabs
located on each
side.
2. Lift cover off
of vacuum
cleaner.
3. Remove the
filter assembly
from the rear
cover.
Secondary
Filter
Primary
Filter_
Filter
Assembly
Rear /_ \
Cove r---_,,_j_.,_
4. Remove primary
filter from
secondary filter.
5. Wash the primary filter ONLY with
cold water only, DO NOT use detergent
or soap. Repeat 10 times or until water
runs clear.
The secondary filter CANNOT be washed
as it will lose its dust trapping ability.
Clean secondary filter by tapping on a
firm surface.
6. Once the primary filter is washed
clean, squeeze by hand and allow to air
dry for 24 hours before putting back into
vacuum cleaner.
NOTE: When the cleaning of the filters
no longer restores vacuum cleaner suction
to full power, replace the filters.
DO NOT operate without primary and
secondary filters installed.
DO NOT wash in the dishwasher.
DO NOT install damp.
8. Reinstall the primary filter into the
secondary filter.
9. Reinstall the
filter assembly by
placing the
bottom of the
filter into the rear
cover and rotating
the top into place.
Rear
Cover_
t
Filter
Assembly
10. Reinstall the rear cover by snapping
into place on the back of the vacuum
cleaner. A noticeable "click" should be
heard,
-20-