Kenwood KGP-2A Operating manual

SERVICE MANUAL
This product complies with the RoHS directive for the European market.
Cabinet
(A02-3660-11)
Dressing Panel
(A21-1632-14)
Model name plate
(B72-1963-14)
Cabinet
(A02-3660-11)
Dressing Panel
(A21-1633-14)
Model name plate
(B72-1964-04)
© 2009-1 PRINTED IN JAPAN
B51-8863-00 (N)PDF
SUPPLEMENT
KGP-2A/2B
MODEM GPS RECEIVER / MODEM GPS CONTROLLER
KGP-2A
KGP-2B
This service manual has been revised due to the modification of
the GPS module and PC board and issues it as a supplemental
manual. This service manual applies to products with 00200101
or subsequent serial numbers.
Refer to the KGP-2A/2B service manual (B51-8596-00) for any in-
formation which has not been covered in this KGP-2A/2B service
manual.
This product uses Lead Free solder.

KGP-2A/2B
2
Document Copyrights
Copyright 2009 by Kenwood Corporation. All rights re-
served.
No part of this manual may be reproduced, translated,
distributed, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or other-
wise, for any purpose without the prior written permission
of Kenwood.
Disclaimer
While every precaution has been taken in the preparation
of this manual, Kenwood assumes no responsibility for er-
rors or omissions. Neither is any liability assumed for dam-
ages resulting from the use of the information contained
herein. Kenwood reserves the right to make changes to any
products herein at any time for improvement purposes.
INSTALLATION............................................3
REALIGNMENT ...........................................5
MODIFICATION ...........................................6
ADJUSTMENT ............................................7
CIRCUIT DESCRIPTION ..............................8
COMPONENTS DESCRIPTION...................8
SEMICONDUCTOR DATA...........................9
PARTS LIST ...............................................10
EXPLODED VIEW ......................................16
PACKING....................................................17
PC BOARD
C ONTROL UNIT (X53-3980-20): KGP-2A ....18
CONTROL UNIT (X53-3980-21): KGP-2B ....22
SCHEMATIC DIAGRAM ............................26
BLOCK DIAGRAM .....................................30
LEVEL DIAGRAM ...................BACK COVER
CONTENTS

KGP-2A/2B
3
TK-980/981 Series (TK-∗80 Series)
■Installing the KCT-34 in the Transceiver
1. Remove the upper cover from the transceiver.
2. Lift the DC cord bushing (q) from the chassis.
3. Remove the pad as shown in the Figure 1 (w).
4. Insert the KCT-34 cable (e) into the chassis (r). The
wire harness band (t) must be inside the chassis.
5. Replace the DC cord bushing (y).
6. Connect the KCT-34 to the TX-RX unit (A/2) as shown in
Figure 2 (u).
:
@
Fig. 1
INSTALLATION
Connector Wire Color Pin No.
A-1 Brown 4
A-2 NC -
A-3 NC -
A-4 Orange 5
A-5 Gray 10
A-6 NC -
A-7 Yellow 6
A-8 Blue 8
B-1 NC -
B-2 White 11
B-3 Green 7
C-1 Purple 9
C-2 Light blue 14
C-3 Light green 15
D-1 NC -
D-2 Black 3
D-3 Red 1
D
C
B
A
1
3
13
15
KCT-36 extension cable
RADIO terminal
KCT-34 KGP-2A/2B
CN1
CN2
CN4
CN3
A
B
C
D
6
=;
.
B
>
Fig. 2

KGP-2A/2B
4
TK-760G/762G/862G/768G/863G/868G Series
(TK-∗60G Series)
■Installing the KCT-35 in the Transceiver
1. Remove the upper cover from the transceiver.
2. Lift the DC cord bushing (q) from the chassis.
3. Remove the pad as shown in the Figure 3 (w).
4. Insert the KCT-35 cable (e) into the chassis (r). The
wire harness band (t) must be inside the chassis.
5. Replace the DC cord bushing (y).
6. Connect the KCT-35 to the TX-RX unit (A/2) as shown in
Figure 4 (u).
:
@
Fig. 3
Connector Wire Color Pin No.
A-1 Brown 4
A-2 Green 7
A-3 NC -
A-4 Orange 5
A-5 NC -
A-6 NC -
A-7 Yellow 6
A-8 Blue 8
B-1 Gray 10
B-2 White 11
B-3 Purple 9
C-1 NC -
C-2 Black 3
C-3 Red 1
A
B
C
3KCT-35
1
13
15
3
KCT-36 extension cable
*RADIO terminal
KGP-2A/2B
=;
.
B
>
CN5
A
B
C
CN4
CN3
Fig. 4
INSTALLATION
* Wiring diagram of RADIO terminal (E37-0982-15: Lead wire with connector)
RADIO
terminal No. Wie color 15-pin connector No.
1 Black 1
2 White 2
3 White 4
4 White 3
5~15 White 5~15
1
15
RADIO terminal
15-pin connector
123
456
789
101112
131415

KGP-2A/2B
5
Transceiver Setting
When the KGP-2A/2B is connected to a transceiver, the
transceiver functions must be set. The transceiver FPU is
used to make this setting.
For a connection method, see Figure 1.
■TK-∗80 Series Setting Method
1. Setting with KPG-49D (K and M markets FPU)
1) Select “Optional Features” from “Edit” on the menu bar
and change Com2 (Internal Port) from “[None]” to “[AUX
Hook/PTT]”.
2. Setting with KPG-60D (E markets FPU)
1) Select “Extended Function” from “Edit” on the menu
bar and change Com2 from “[None]” to “[AUX Hook/
PTT]”.
■TK-∗60G Series Setting Method
Use the KPG-56D as the FPU.
1) Select “Key assignment” from “Edit” on the menu bar,
and set “Foot Switch” to ”[None]”.
REALIGNMENT
2) Select “Optional Features” from “Edit” on the menu
bar and change “ACC Hook/DTC” from “[ACC Hook]” to
“[DTC]”.
Note :
Applicable only for S/No. 302XXXXX or later.
KGP-2A/2B Setting
After programming the transceiver, you need to config-
ure the KGP-2A/2B. Using the FPU (KPG-73D), you can con-
figure the KGP-2A/2B .
Using a cross-wired serial cable (KGP-2A/2B side : D-sub
9- pin female) as shown in Figure 2, plug one connector into
the RS-232C (COM) port of your PC and the other end to
the ACC1 connector on the rear panel of the KGP-2A/2B.
■KGP-2A/2B Setting Method
1) Create a data file using the FPU (KPG-73D).
2) After configuring the KGP-2A/2B to the Programming
Menu mode, upload the data file to the KGP-2A/2B.
• For detailed instructions, refer to the Help file included in
the FPU.
• To set the KGP-2A/2B in the Programming Menu mode,
refer to “Start the Programming Menu mode” on page 7.
IBM-PC
KPG-46
Transceiver
KGP-2A/2B
KPG-49D or KPG-60D : TK-*80
KPG-56D : TK-*60G
IBM-PC
KPG-73D : KGP-2A/2B
KGP-2A/2B
Transceiver
Cross-wired serial cable
(KGP-2A/2B side :
D-sub 9-pin female)
Fig. 1
Fig. 2

KGP-2A/2B
6
Connecting a Separate Microphone for
Emergency Mode (KGP-2A only)
If you apply the modification as described below, you
can connect a separate microphone to the KGP-2A in place
of the transceiver’s microphone for Emergency mode. The
base station application software which can send out a cor-
responding command is required for the change of a micro-
phone which operates in the time of emergency transmis-
sion.
■Modification
1. Remove R171 (0Ω).
2. Remove R172 (0Ω).
3. Add 0Ω(RK73GB2A000J) to the $R17 location.
4. Add 0Ω(RK73GB2A000J) to the $R18 location.
J1
ACC3
11
1
Add Remove
5
610
15
$R17 $R18
R171 R172
CONTROL UNIT
(X53-3980-20)
Component side view
J1 (ACC3) Pin 5 : Microphone input
J1 (ACC3) Pin 6 : Microphone ground (GND)
MODIFICATION
Since 5V DC goes through R55 (56kΩ) and then it is sup-
plied to the microphone input, an electric condenser-type
microphone can be connected to this terminal.
You can also adjust the microphone sensitivity by chang-
ing the R206 (560Ω) constant between 330Ωand approxi-
mately 1kΩ. The microphone pre-emphasis and IDC are
carried out by the DSP IC (IC29).
Modification Setting for DGPS (KGP-2A only)
Input method of
DGPS signal
$R192
(0Ω)
R186
(0Ω)
$R184
(0Ω)
$R185
(0Ω)
R191
(0Ω)
5V input from ACC2 Yes No Yes No No
RS-232C level input
from ACC2 Yes No Yes No Yes
5V input from ACC3 Yes No No Yes No
RS-232C level input
from ACC3 YesNo NoYesYes
Input method of
DGPS signal
$R190
(0Ω)
$R221
(0Ω)
R162
(0Ω)
R169
(0Ω)
5V input from ACC2 No No No N/A
RS-232C level input
from ACC2 Yes Yes No N/A
5V input from ACC3 No No N/A No
RS-232C level input
from ACC3 Yes Yes N/A No
R162 R169
$R190
$R221
R186
$R184 $R185
R191
$R192
CONTROL UNIT (X53-3980-20)
Component side view

KGP-2A/2B
7
Front Panel
GPSDATA
DC
SOURCE
DC SOURCE LED GPS LED (KGP-2A only)
DATA LED MODE SW
Start the Programming Menu Mode
Press and hold the MODE SW key for more than 2 sec-
onds. “DC SOURCE” LED blinks and then the KGP-2A/2B
enters the programming menu mode.
Note: If the KGP-2A/2B does not receive any programming
commands from a PC within 30 seconds after the “DC
SOURCE” LED starts blinking. It returns normal operation
(User mode). If you press MODE SW key while the “DC
SOURCE” LED is blinking, the KGP-2A/2B returns to User
mode.
Updating the Firmware
1) Connect the transceiver and KGP-2A/2B as shown in Fig-
ure 2 on page 5.
2) Double-click the “Fpro.exe” file (Ver. 3.01 or later) in the
folder where the KPG-73D is installed.
3) After the program starts, click the “Open a file” icon [ ],
then select the new firmware data file.
4) Configure the KPG-2A/2B to enter the Programming
menu mode, then, click [Write] on the Fpro screen to
start revising the firmware. (The Fpro program first eras-
es the firmware file on the KGP-2A/2B, then writes the
new firmware file.)
• While erasing the firmware, the “DC SOURCE” LED
blinks green and the “DATA” LED lights orange.
• While writing the firmware, the “DC SOURCE” and
“DATA” LEDs blink green.
• When the firmware is successfully revised, only the
“DC SOURCE” LED blinks green.
• When an error occurrs, the “DC SOURCE” LED blinks
green and the “DATA” LED blinks red. In this case,
switch the KGP-2A/2B OFF, then turn it ON again. The
“DC SOURCE” LED blinks green and the “DATA” LED
lights orange. Click [Write] on the Fpro screen to re-
start revising the firmware.
5) Click “OK” when the confirmation dialog box appears.
Select [Exit] to exit the program.
6) Turn the KGP-2A/2B OFF and then back ON to return to
User mode.
MSK Modulation Adjustment
Adjust deviation as follows: Wide: 3kHz and Narrow:
1.5kHz.
1) Connect a transceiver and a PC to the KGP-2A/2B (Figure
2 on page 5). After configuring the KGP-2A/2B to enter
the Programming menu mode, select “Test Mode” from
“Program” on the FPU (KPG-73D) menu.
ADJUSTMENT
2) Measure the KGP-2A/2B DO voltage (DO: CN1 pin 5)
with AF-VTVM and adjust the “Output Level” DIGIT
value according to the table 1 on the “MSK” adjustment
screen.
3) When you click on “OK” on the PC screen, the adjust-
ment value is written into the KGP-2A/2B memories.
MSK Detection Input Level Adjustment
Set the input voltage at pin 2 of the CODEC IC (IC22) of
the KGP-2A/2B to 1000mVp-p.
1) Adjust the SSG level as shown below. Then connect the
output to the transceiver.
Frequency : Same frequency that the transceiver is re-
ceiving.
Modulation Frequency : 1200Hz (or 1000Hz)
Frequency Deviation : 3kHz (Wide), 1.5kHz (Narrow)
Output Level : –53dBm (60dBµ)
2) Measure the KGP-2A/2B DI voltage (DI: CN1 pin 3, trans-
ceiver detection output voltage) with a AF-VTVM.
3) Set the “Input Level” DIGIT value according to the table
2 on the “MSK” adjustment screen in “Test Mode” so
that the measured voltage (mVrms) is the CODEC IC in-
put voltage (1000mVp-p).
4) When you click on “OK” on the PC screen, the adjust-
ment value is written into the KGP-2A/2B memories.
Table 1 DO output level vs DIGIT value
DIGIT value
DO output level (mVrms)
50 200 400 600 800 1000 1200
80
40
20
60
100
120
140
160
180
200
220
240
10
0
20
40
60
80
100
120
140
160
180
200
220
240
Table 2 DI input level vs DIGIT value
DIGIT value
DI input level (mVrms)
50 200 400 600 800 1000 1200
145
59
29
20
15 12 10 987766
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150

KGP-2A/2B
8
1. Power Supply Circuit
The KGP-2A/2B power supply circuit uses a dedicated
regulator IC for each circuit application so that the circuits
do not interfere with each other. (Figure 1)
2. Digital Control Circuit
■GPS module (KGP-2A only)
The location data is measured by the internal GPS mod-
ule. When the KGP-2A is turned OFF, it enters the backup
mode and the power is supplied by the internal rechargeable
lithium battery. It takes approximately 40 seconds to calcu-
late the location data when the KGP-2A is “cold” started (full
initializing).
COMPONENTS DESCRIPTION
CIRCUIT DESCRIPTION
IC3 IC10
IC13
8V
IC4
8V
3.3V
1.8V
3.3V DSP I/O
(KGP-2B CPU)
1.8V DSP Core
5V analog
(KGP-2A CPU)
GPS module
3.3V analog
SB
IC7
IC11
5V
3.3V
GPS module
VANT
IC34
3.3V
Fig. 1
Control Unit (X53-3980-XX)
Ref. No. Use / Function Operation / Condition
IC1 Reset IC Monitor of SB power supply voltage
IC3,4 Regulator 8V (1A)
IC6 RS-232C driver Level converter 5V↔RS-232C
IC7 Regulator 5V (500mA)
IC9 Extended I/O Radio control, Serial/parallel conver-
sion
IC10,11 Regulator 3.3V
IC12 Shift register LED (D26~28) control, Power
switch of GPS module
IC13 Regulator 1.8V
IC14 Reset IC Monitor of CPU power supply voltage
IC15 EEPROM Memory backup
IC16 Amplifier Input data
IC17 CPU 16 Bit
IC18 D/A converter
IC19 Level converter 5V↔3V
IC20,21 Level converter 5V→3V
IC22 CODEC IC A/D,D/A conversion
IC23 Gate IC IC19 direction control
IC24 Gate IC A19 (IC17) Logic inverter
IC25 Memory IC 3.3V FLASH ROM
IC26 Ampifier Output data
IC28 Clock demultiplier for DSP
IC29 DSP IC
IC31 Level converter 5V→3V
Ref. No. Use / Function Operation / Condition
IC32 Amplifier Microphone input signal
IC34 Regulator 3.3V
Q1,2 Switching Level converter 3V→5V
Q4 Switching Power switch of GPS module
Q5,6 Switching Output terminal open-collector
Q7,8 Switching Output terminal open-collector
Q10~14 Switching Level converter 3V→5V
Q15 Switching Logic inverter
Q16~26 Switching Level converter 3V→5V
D1 Over current
protection 0.75A
D2 Backward voltage
protection
D5 Reverse current
protection
D7~9 Surge absorption
D12 Surge absorption
D18 Reverse current
protection
D24 Surge absorption
D26 LED DC SOURCE (Power)
D27 LED GPS
D28 LED DATA (TX/RX)
D30 Reverse current
protection
D31~48 Surge absorption
D50~62 Surge absorption

KGP-2A/2B
9
SEMICONDUCTOR DATA
CPU: 30620M8A2M6GPU (Control unit IC17)
Pin No. Pin Name I/O Function
1~5 SEN12~
SEN8
I/O KGP-2A Sensor 12~8
I KGP-2B Not used
6 BYTE I Data bus width 8 bit
7 CNVSS I Memory extended mode select
(GND)
8 MES I Microprocessor operation mode
9 FRBSY I FLASH ROM busy detect
10 RESET I Reset input
11 XOUT O Clock output
12 VSS - GND
13 XIN I Clock input
14 VCC - Power supply
15 NMI I Not used
16 SRCLK1 I
KGP-2A SWIPE READER CLOCK1
input
KGP-2B Not used
17 SRCLK2 I
KGP-2A SWIPE READER CLOCK2
input
KGP-2B Not used
18 PFINT I
Power supply voltage monitor input
19 E2PSCL O E2PROM SK
20 VRLD O Electronic VR LD
21 - I Not used
22 SEN_ACC2/1 I Not used
23 SEN_ACC2/2 I Not used
24 SEN_ACC3 I Not used
25 RADOE O IC9 OE (for RADIO)
26 RADST O IC9 ST (for RADIO)
27 RXD2 I KGP-2A Radio data input
KGP-2B Not used
28 TXD2 O KGP-2A Radio data output
I KGP-2B Not used
29 TXD1 O PC data output
30 RXD1 I PC data input
31 CLK O Common CLOCK
32 DATA O Common DATA
33 TXD0 OKGP-2A GPS receiver output
(GPSTXD)
I KGP-2B Not used
34 RXD0 I
KGP-2A GPS receiver input
(GPSRXD)
KGP-2B Not used
Pin No. Pin Name I/O Function
35 RADSQ I Radio SQ input
36 RADTXS I Radio TXS input
37 RDY I Not used
38 ALE O Not used
39 HOLD I Not used
40 HLDA O Not used
41 BCLK O Not used
42 RD O Read signal
43 BHE O Not used
44 WR O Write signal
45 DSPCS O DSP chip select
46 E2PSDA I E2PROM DI
47 E2PWP O E2PROM DO
48 FROMCE O FLASH ROM CE
49~59 A19~A9 - Address bus 19~9
60 VCC - Power supply
61 A8 - Address bus 8
62 VSS - GND
63~70 A7~A0 - Address bus 7~0
71 MODESW O Mode SW
72 DSPRINT I DSP RX interrupt
73 DSPTINT I DSP TX interrupt
74 DPSCLR O DSP reset output
75 SRSEL I KGP-2A SWIPE READER SELECT
KGP-2B Not used
76 SRDAT1 I KGP-2A SWIPE READER DATA1
KGP-2B Not used
77 SRDAT2 I KGP-2A SWIPE READER DATA2
KGP-2B Not used
78 LEDLCK O IC12 LCK (for LED)
79~86 D7~D0 - Data bus 7~0
87~93 SEN7~
SEN1
I/O KGP-2A Sensor 7~1
I KGP-2B Not used
94 AVSS - Analog power supply (GND)
95 SEN0 I/O KGP-2A Sensor0
I KGP-2B Not used
96 VREF - Reference voltage
97 AVCC - Analog power supply
98~100 SEN13~
SEN15
I/O KGP-2A Sensor 13~15
I KGP-2B Not used

KGP-2A/2B
10
✽New Parts. indicates safety critical components.
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Teile ohne Parts No. werden nicht geliefert.
L: Scandinavia K: USA P: Canada
Y: PX (Far East, Hawaii) T: England E: Europe
Y: AAFES (Europe) X: Australia M: Other Areas
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
PARTS LIST
KGP-2A (Y57-3770-20)
CONTROL UNIT (X53-3980-20): KGP-2A
1 2A A02-3660-11 PLASTIC CABINET
2 2B A21-1632-14 DRESSING PANEL
4 1A B09-0355-05 CAP (D-SUB 9P)
5 1A B09-0626-05 CAP (D-SUB 15P)
6 1A B42-3395-04 STANDARD LABEL
7 2A B42-7033-04 STICKER (ID)
8 2A B42-7733-04 STICKER (WEEE)
9 1D B62-1481-00 INSTRUCTION MANUAL
10 2A B72-1963-14 MODEL NAME-PLATE
12 1A E37-0982-15
LEAD WIRE WITH CONNECTOR (15P:RADIO)
13 2A
✽E37-1001-15
LEAD WIRE WITH CONNECTOR (4P:CN19)
14 1B
✽E37-1414-15 LEAD WIRE WITH CONNECTOR (ANT)
16 2B F20-3339-04 INSULATING SHEET
18 1B G10-1292-04 FIBROUS SHEET (CHASSIS:REAR-TOP)
19 1B G10-1293-04 FIBROUS SHEET (CHASSIS:REAR-R&L)
20 1B G10-1294-04
FIBROUS SHEET (CHASSIS:BOTTOM-R&L)
21 1B G10-1295-04 FIBROUS SHEET (CHASSIS:BOTTOM-FRONT)
22 2A G13-1882-04 CUSHION (15P CONNECTOR)
23 1A G13-1888-04 CUSHION (CHASSIS BOTTOM)
24 2A G13-1889-14 CUSHION (D-SUB)
25 1A G13-1915-04 CUSHION (CHASSIS D-SUB)
26 1A G13-2001-04 CUSHION (GPS MODULE)
27 1B
✽G13-2235-04 CUSHION (PCB)
28 1B
✽G13-2236-04 CUSHION (ANT CONNECTOR UPPER)
30 3E H25-0796-04 PROTECTION BAG
31 1E H52-1860-02 ITEM CARTON CASE
33 2E J29-0728-03 BRACKET ACCESSORY
- J39-0641-04 SPACER (15P:RADIO CONNECTOR)
36 2B K29-9176-04 KEY TOP (MODE SW)
A 1A N14-0596-15 HEXAGON NUT (ANT)
B 1A N15-1060-48 FLAT WASHER (ANT)
C 1A N17-1060-48 TOOTHED LOCK WASHER (ANT)
D 2A,2B N82-2606-43 BINDING HEAD TAPTITE SCREW (PCB)
E 2A N82-2610-48
BINDING HEAD TAPTITE SCREW (D-SUB)
F 1A,1B N88-3010-43 FLAT HEAD TAPTITE SCREW (CHASSIS)
38 2E N99-2048-05 SCREW SET ACCESSORY
40 2D
✽T90-1077-05 ANTENNA (GPS) ACCESSORY
42 2A
✽W02-3705-05
ELECTRIC CIRCUIT MODULE (GPS MODULE)
D26,27 B30-2056-05 LED
D28 B30-2019-05 LED (RE/GR)
C1-11 CC73GCH1H101J CHIP C 100PF J
C12 CK73GB1E103K CHIP C 0.010UF K
C13-17 CC73GCH1H101J CHIP C 100PF J
C18 CK73GB1E103K CHIP C 0.010UF K
C19-23 CC73GCH1H101J CHIP C 100PF J
C24 C92-0895-05 ELECTRO 100UF 25WV
C25 CK73GB1H471K CHIP C 470PF K
C26-28 CC73GCH1H101J CHIP C 100PF J
C30-35 CC73GCH1H101J CHIP C 100PF J
C37 CC73GCH1H101J CHIP C 100PF J
C38 CK73GB1E103K CHIP C 0.010UF K
C39,40 CC73GCH1H101J CHIP C 100PF J
C42,43 CK73GB1C104K CHIP C 0.10UF K
C44,45 CC73GCH1H101J CHIP C 100PF J
C47 CK73GB1E103K CHIP C 0.010UF K
C48-51 CK73GB1C104K CHIP C 0.10UF K
C54 CK73GB1C104K CHIP C 0.10UF K
C55,56 CS77AA1E010M CHIP TNTL 1.0UF 25WV
C57,58 CK73GB1C104K CHIP C 0.10UF K
C59 CS77AA1E010M CHIP TNTL 1.0UF 25WV
C61 CS77AA1E010M CHIP TNTL 1.0UF 25WV
C62,63 CK73GB1C104K CHIP C 0.10UF K
C65 CK73GB1C104K CHIP C 0.10UF K
C66 CK73GB1E103K CHIP C 0.010UF K
C67 CK73GB1C104K CHIP C 0.10UF K
C68 CS77AA1A100M CHIP TNTL 10UF 10WV
C69 CK73GB1C104K CHIP C 0.10UF K
C70 CK73GB1E103K CHIP C 0.010UF K
C72 CK73GB1C104K CHIP C 0.10UF K
C74 CK73GB1E103K CHIP C 0.010UF K
C75 CK73GB1H471K CHIP C 470PF K
C76,77 CS77AA1A100M CHIP TNTL 10UF 10WV
C81 CC73GCH1H101J CHIP C 100PF J
C82,83 CK73GB1C104K CHIP C 0.10UF K
C87,88 CS77AA1A100M CHIP TNTL 10UF 10WV
C89 CK73GB1C104K CHIP C 0.10UF K
C91 CC73GCH1H101J CHIP C 100PF J
C94,95 CK73GB1E103K CHIP C 0.010UF K
C96,97 CS77AA1A100M CHIP TNTL 10UF 10WV
C98 CK73GB1E103K CHIP C 0.010UF K
C99 CS77AA1A100M CHIP TNTL 10UF 10WV
C101 CS77AA1A100M CHIP TNTL 10UF 10WV
C102,103 CK73GB1C104K CHIP C 0.10UF K
C104,105 CS77AA1A100M CHIP TNTL 10UF 10WV
C106 CK73GB1E103K CHIP C 0.010UF K
C107 CK73GB1C104K CHIP C 0.10UF K
C108,109 CS77AA1A100M CHIP TNTL 10UF 10WV
C110 CK73GB1E103K CHIP C 0.010UF K
C114 CS77AA1A100M CHIP TNTL 10UF 10WV
C115 CK73GB1E103K CHIP C 0.010UF K
C117 CK73GB1C104K CHIP C 0.10UF K
C118 CK73GB1H332K CHIP C 3300PF K
C119 CS77AA1A100M CHIP TNTL 10UF 10WV
C120 CC73GCH1H271J CHIP C 270PF J
C121 CK73GB1C104K CHIP C 0.10UF K
C122 CK73FB1A475K CHIP C 4.7UF K
C123,124 CK73GB1E103K CHIP C 0.010UF K
C125-127 CS77AA1A100M CHIP TNTL 10UF 10WV
C128,129 CK73GB1H471K CHIP C 470PF K
KGP-2A
CONTROL UNIT (X53-3980-20): KGP-2A