Kenwood KR-V7060 User manual

GOO/ANAD
AUDIO VIDEO STEREO RECEIVER
KR-V7060
KR-V6060
INSTRUCTION MANUAL
KENWOOD CORPORATION
This manual contains instructions for two models.
For your records
Record the serial number, found on the back of the unit, in the spaces designated on the warranty
card, and in the space provided below. Refer to the model and serial numbers whenever you call
upon your dealer for information or service on this product.
Model Srial Number
Unpacking
Unpack the unit carefully and make sure that ail accessories are put aside so they will not be lost.
Examine the unit for any possibility of shipping damage. If your unit is damaged or fails to operate,
notify your dealer immediately. !f your unit was shipped to you directly, notify the shipping com-
pany without delay. Only the consignee (the person or company receiving the unit} can file a claim
against the carrier for shipping damage. :
We recommend that you retain the original carton and packing materials for use should you trans-
port or ship the unit in the future.
Accessories
Loop antena stand ........(1)
(1} Batteries (R6/AA)
e—
Except for U.S.A., Mexico,
Canada, and Australia
B60-1441-10 CSID(K,P,M.Y,R) (MG!
——

pplying power .
Be Ea a RS OP ea EF Ea Tee EEE ae Ee alla eee ae
¢ Units are designed for operation as follows.
U.S.A, Mexico ad Ca ada ssesecseccceeeecerscissssnnisenmnes 120 V only OOF COUNITIOS esssssessssccrseesseessseecsrsrserseeseiee 110~120 { 220~240 V swite
PUSHED sssiseicvccosincrinmivertocnssindnieeisotssrssntiseriosstrmestitronstsommsscsstennnised tO V ONLY
AC voltage selection AC voltage Selector switch
This unit operates on 110 - 120 volts or 220 -
240 voits AC, The AC voitage selector switch AAG tt0- : Ae Taviaois: “AC palo E
3 <_h
on the rear panel is set to the voltage that pre-
vails in the area to which the unit is shipped.
Before connecting the power cord to your AC
outlet, make sure that the setting position of
this switch matches your line voltage. If not, it
must be set to your voltage in accordance with
the following direction. :
| KR-V7060 | KR-V6060
Note: ee Move switch lever to match your line voltage with
Our warranty does not cover damage caused by excessive line a small screwdriver or other pointed tool.
voltage due to improper setting of the AC voltage selector switch.
._,oafety precautions _..
WARNING :TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN
OR MOISTURE.
CAUTION CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
RISK OF ELECTAIC SHOCK (OR BACK), NO USER-SERVICEABLE PARTS INSIDE, REFER SERVICING TO QUALIFIED
DO
NOT
OPEN
SERVICE
PERSONNEL,
3
THE LIGHTNING FLASH WITH ARROWHEAD SYMBOL, WITHIN AN EQUILATERAL TRIANGLE, IS
INTENDED TO ALERT THE USER TO THE PRESENCE OF UNINSULATED "DANGEROUS VOLTAGE”
WITHIN THE PRODUCT'S ENCLOSURE THAT MAY BE OF SUFFICIENT MAGNITUDE TO CONSTITUTE A
RISK OF ELECTRIC SHOCK TO PERSONS.
THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE IS INTENDED TO ALERT THE USER TO
THE PRESENCE OF IMPORTANT OPERATING AND MAINTENANCE (SERVICING) INSTRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE,
For the U.S.A.
FCC WARNING
This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
NOTE:
This equipment has been tested and found to camply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rutes. These
limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment may cause harmful
interference to radio communications, if it is not installed and used in accordance with the instructions. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by ane or more of the following
measures;
~~ Reorient or relocate the receiving antenna.
~- Increase the separation between the equipment and receiver.
—- Connect the equipment into an outlet_on a circuit different from that to which the receiver is connected.
~— Consult the dealer or an experienced radio / TV technician for help.
For the U.S.A.
Note to CATV system installer:
This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper
grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of
cable entry as practical.

Special features _ She ss ee
ee mead ete ft re ae i re nn a ROO OEE EPPO P DEINE APDIP DEERE AED D RED Neri tlm iene orn cobheedenderbtberomenecors tes! ae with SRA ie ee! SDE ene eg sheet tecinaatnarine au
The surround system reproduces video software programmes cose
carrying the TXi[Bour sumoun) mark with similar acoustic effects
to movie theaters.
The DOLBY PRO LOGIC mode controls the audio signals of the
Front Left/Right, Center and Rear surround channels using the
built-in directivity enhancer circuit to reproduce the feeling of
sound motions realistically.
The DOLBY 3 STEREO mode can reproduce the motions of sound
aven when only the front and center speakers are used, by
providing proper acoustic position using the directivity enhancer
circuit.
This mode adds presence sound components to the signals output
from the DOLBY PRO LOGIC (Left, Center, Right and Surround
channels), allowing movie software programmes to be played
with a similar feeling of presence to movie theater in a listening
room at home.
Contents.
” Before applying power ABefore applying DOWEM.......ccssccscscecssecevecvesseresereseereatesenees Sn TREC ENON iyi revtere ae 2
ASafety Precautions oo... cceseseeceterenes seuss ahs Siitutl rdvetharniacieAteteciateatteraaita essen: 2
Special features
System connection
sites od rone
Controls and indicators
Operation of remote control unit
Playing music
Sound adjustment functions
Recor ding Sprain arom aaenconuematalersonsanesseeRso
R gearcine SnaCansaeLaganesiaiwng de cepa desea ened lehdcadiets eternedata shiva Tanta vadlavadsei ting tsivedaigvehelved ebebeasdintates
Copying tapé (Tape GubbINg) ..........cccecesseceverssaesecereeneee
Broadcast rec epti OUD eessesetattenteniidee tented rete haar eon 2 cee rea eoeerrennmersomeneees
Receiving broadcast station.
SR Re a A
Receiving radio station by specifying its frequency . pigabante bird uclea wisn bias Selgantnadit eid
Storing radia stations in mamory (Station preset) ..........c:ceeseeee sates videadeteaunene a
Operation of video components SEAS RRR EP FET EE PR BB EE RAR OD, MRS ETRE TILES VEINS AR oe
Playback of videotape ..... ee e Lahbreli inte sues Patch ddan'udds a oaas pep deaeh aa vinninehan aia
Recording of video source...
DOLBY PRO LOGIC surround atianoerent Gb digadealitaeebiehdieid ica e Nea Mise ea a eke ect aahel es
DOLBY PRO LOGIC surround playback ....eecessseeaees Pen dice tshaclteastele MoS! Cauucees tee
DOLBY 3 STEREO adjustment and playback oo... cccccssesssescsseresecsecsssesasstcaseceasentes
Enjoying music with feeling of preserice (THEATER LOGIC mode)... cece eeeeeee 25
in case of difficulty sess atau ihank at Metal oneal telat Ota tare aeisater cde gests eens duee Semis etched cota ca nti ae ES
Specifications fice aan see aS thas esate ne aia lecl ot eet aie once Teaedh ode ales to laa tiil Shin M lites eins 2S

KR-V7060
Make connection as shown below.
When connecting the related system components, refer also to the instruction manuals of the related components.
Do not plug in the power lead until all connections are completed.
LD Player or VIDEO DECK 2 Monitor TV AC outlets
For other countries ex-
cept for the U.S.A,
Mexico and Canada
Audio cut | Video out
Video in Video out
Audio out | ff Audio in |
Audio cord
rane Oo= may a
eli: 2 © (ow ses am
To AC
outlet
+ +
Lamat FRONT 3? RS
| Rett a
Tape deck 2
oO
Turntable
©) ©) a
CD player eystem NV Brae nee
® ©
> Eo
SYSTEM
Tape deck 1 A eee
Y if
SX
syrumsomrteort
@ This unit has a cooling fan on the rear aie Do not Cee ange near the loth fan.
Automatic operation
When this unit is connected to KENWOOD system components such as @ cassette deck and CD player through system control cords and the input
source is selected with the INPUT SELECTOR, the selected component starts to play automatically, Inversely, playing a component automatically
selects that source as the input to this unit. The automatic operation also occurs when the provided remote control is used.
1. Connect all cords firmly. lf connections are loose, there could be loss _of sound or noise produced.
2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging / unplugging
connection cords without removal of the power cord can cause malfunctions or damage to the unit.
3. De not connect up a power source which is larger than that jndicated on the socket at the rear of the unit.
4. Insert the system control plugs completely into the jacks.
5. lf the system control cords or audio cords are not connected properly, the remote control or automatic operation between system
components will not work properly.

_Connectionofspeakers,§ — er
oo $2 = : il ero et oo lar 8) tea es ees Ene ade BOER
mae
SPEAKER SYSTEM A
® Push lever. sececeeer EN Scecesereres
D RNY Kee Center speaker
(82. ~ 16Q}
R Zz R | L
nA iRatetetetee MEE tetatetatse ETRE] FERRY
@ Never short-circuit the + and - speaker cords. : Reine — KKK seccetetate: ME statatetsty’
e lf the left and right speakers are connected inversely or if the Rearseed Ktoiong
i : : Rocere, Wrogeeaeces.
speaker cords are connected with reversed polarity, the sound Rose resesocenes
becomes unnatural with ambigous acoustic image positioning. BEE ot sfatate® MEN stotctacete® (80 ~ 16Q)
etetetetete letetetetete =
Be sure to connect the speakers and speaker cords correctly.
e Proper sound will not be produced unless two rear speakers are SPEAKER SYSTEM B
connected.
alana pe preniarninee arn a —_ TB SR RA aR Ra pe rm ep ey mt PR Nc PP RET |
Speaker IMPEDANCE SELECTOR CAUTION : During operation of the speaker IMPEDANCE SELECTOR, set the POWER switch to OFF.
Set the IMPEDANCE SELECTOR switch on the rear panel according to the impedance of the front speakers used. The center. and rear speakers
should have impedances from 8 to. 16 ohms regardless of the position of this switch, ae
Front speaker impedance Selector position
=
Aor B speakers 40 ~ 6Q CO |
Aand
B
speakers
8Q
~
1682
AcrB:LESSTHANS2
AorB:
AandB:SQO0RMORE
=
82
0R
MORE
IMPEDANCE SELECTOR
=>
Lo
<<
AorB: LESS THAN 8 AorB;
Aand B: 82 OR MORE 82 OR MORE
IMPEDANCE SELECTOR
Aor B speakers 82 ~ 160
e |tis not possible to use both A and B speaker systems for surround play.
e (tis not possible to use both A and B speaker systems if speakers have impedances from 4 chms to 6 ohms.
PRE QUT jacks
Use these jacks when you want to play music with larger volume level than the level obtained with normal connection, or when you want to enjoy
music with different tones.
Speakers cannot output sufficient sound level even when they are connected directly to the PRE OUT jacks. These jacks should be connected to
speakers containing an amplifier or to amplifiers to which speakers are connected.
i e¥ a" a" aa" aa":
Amplifier — Amplifier
b A OT
CKO OT
tetas eeeete
- Rear surround
Amplifier speakers
"e's" 6 "6" S a 6 'e"
Amplifier
Sub woofer
e Connect a sub woofer if you want.te enhance the bass sound.

Make connection as shown below.
“Dithhkt pene:
When connecting the related system components, refer also to the instruction manuals of the related components.
Do not plug in the power lead until all connections are completed.
VIDEO DECK 1 LD Player or VIDEO DECK 2 Monitor TV :
Video in Video out Audio out Video aut
Audio out] § Audio in
Audio cord
To AC
outlet
(ESSTIUNES 4
ARCIMCRE F
AC outlets
Except for the U.S.A.,
Mexico and Canada
@_Y
tRONT SPEAMEAE
cAeR @ tea
Amg® 3 Wel
Tape deck 2
Turntable
a = © =" [==] —
==" je Hemel
CI oocs#eem CLoio ©) ESI
BD
pl
r
SYSTEM
cers)
==
ew
SYSTEM
CD playe CONTROL PLAY REG Tape deck 1 CONTROL
oN Systam control cord VA
Peet
Automatic operation
When this unit is connected to KENWOOD system components such as a cassette deck and CD player through system control cords and the input
source is selected with the INPUT SELECTOR, the selected component starts to play automatically. Inversely, playing a component automatically
selects that source as the input to this unit. The automatic operation also occurs when the provided remote control is used.
ee ee tact ht og
1. Connect ail cords firmly. If connections are loose, there could be loss of sound or noise produced.
v 2. When plugging and unplugging connection cords, be sure to first remove the power cord from the AC outlet. Plugging / unplugging
connection cords without removal of the power cord can cause malfunctions or damage to the unit.
3, Do not connect up a power source which is larger than that indicated on the socket at the rear of the unit.
4, Insert the system control plugs completely into the jacks.
5. If the system contro] cords or audio cords are not connected properly, the remote contro! or automatic operation between system
components will not work properly.
CS

Connection.of speakers tg
eet ete
@ Push lever.
rh A bo. 44.64
O46 + oe CE I
Yetetetetete Petar etree Center speaker
+o $8 + KOO
stetetetetet wratatatete!
etetetete? ME breteceteres 8Q ~ 160
Cx eK +.¢ 664.4
i MO x OM
+ 6 +o ++ + 8
+o + oo + Ox KOK A
++ + + © +o + 6 + 8 OK
bet eae x KK 244 0 + &
CK OO ++ +o 4 Pat
ko O49 4 i MK HK 246.9 4 &
OK OK SO | Pt OG
eK KMD bo 464 4 Le MA
+. +o 6 > + ot PO
Mbatatetets trata tes Setatetetet.
Metetetetet stetetetete: areteterete
( Insert cord.
2
@) Return lever.
L oR L
# Never short-circuit the + and - speaker cords. seaestates MM cocoeasegoet MMMM Socaseseiee: IMM eesooneeses
: ‘i mexecetatet Hreseracotet Statetete’: peed
e If the left and right speakers are connected inversely or if the sSetetetogs MEM oseseseseet PN siseeeneees: BEM czeceesees
speaker cords are connected with reversed polarity, the sound ececeseces mM evceceeetot nnn
becomes unnatural with ambigous acoustic image positioning. seetetesese reesececs Rear speaker
?,
Be sure to connect the speakers and speaker cords correctly. Reo «= Rod (80 ~ 160)
e Proper sound will not be produced unless two rear speakers are SPEAKER SYSTEM B
connected, Sia:
Speaker IMPEDANCE SELECTOR
Set the IMPEDANCE SELECTOR switch on the rear panel according to the impedance of the front speakers used. The center and rear speakers
should have impedances from 8 to 16 ohms regardless of the position of this switch. ,
For surround play For non-surround play
Front speaker impedance Selector position Front speaker impedance Selector position
LESS THAN BQ ‘A LESS THAN 8.9 ae)
Aor B speakers 40 ~ 6Q © &8Q0R MORE ¥ A or B speakers 49 ~ 6Q 8QORMORE ¥
IMPEDANCE IMPEDANCE
SELECTOR SELECTOR
LESSTHANEO 4 Aor B speakers 8Q~ 16Q — LESS THANS
Aor B speakers 82 ~ 169 8 2 OR MORE 4 A a Beccatan 80 ee $2 OR MORE ‘a
IMPEDANCE IMPEDANCE
SELECTOR SELECTOR
@ It is not possible to use both A and_B speaker systems for surround play.
e It is not possible to use both A and B speaker systems if speakers have impedances from 4 ohms to 6 ohms.

Connection method to each antenna terminal
@Push tever, @Insert cord. (3) Return laver.
e
AM loop antenna connection AM outdoor antenna connection
The supplied antenna is for indoor use. Place it as far as possible from If the reception is poor when the AM loop antenna is used, distribute
the main system, TV set, speaker cords and power cord, and set it to a vinyl-coated wire of more than 6 meters outdoors, without discon-
a direction which provides the best reception. necting the loop antenna.
Outdoor antenna
Loop antenna
3 UEURIETUPR Tears PSEETEE
Pegs ey iw SETS SCL ai SA se OE Eee ANIME tt
“AM indoor antenna connection FM outdoor antenna connection
The supplied antenna is for indoor use. For stable reception, remove Lead the 759 coaxial cable connected to the FM outdoor antenna into
the indoor antenna after installing an outdoor antenna as soon as pos- the roam and connect it to the FM 75 terminal.
sible.
FM indoor antenna
Coaxial cable

ARIPO ICO
FM DE-EMPHASIS / CHANNEL SPACE switch
(Except for U.S.A., Mexico and Canada)
The FM DE-EMPHASIS / CHANNEL SPACE switch on the rear panel
is set to the correct setting that prevails in the area to which the unit
is shipped. However, if the FM DE-EMPHASIS / CHANNEL SPACE
- setting is not matched to the area where the unit is to be used, for
instance, when you moved from area 1 to area 2 or vice versa, de-
sired reception of AM/FM broadcasts is not expected. In this case,
change the FM DE-EMPHASIS / CHANNEL SPACE setting in accor-
dance with the area corresponding to the table, The FM DE-EMPHA-
SIS is switched over at the same time.
e@ When changing the setting of the FM DE-EMPHASIS / CHANNEL __.
SPACE switch, first disconnect the power cord of the amplifier,
then reset the channel space switch, connect the power cord
again, and turn the power on, can
KR-V7060 KR-V6060
AM FM ;
1OkHz 100kHzH f_| A 7545
kHz SOkH2F ¥ Sous :
AM: 10kHz
American countries
Other countries
U.S.A., Canada,
Hawaii,
South
FM:
—
100kHz

sa
Ss code
10
SRS &
Broadcast band indicators
SPEAKERS indicators
VIDEO 1/2 indicators Frequency display,
Input display,
Preset channe! display,
Surround mode display
3 STEREO indicator
LOUDNESS indicator.
Reception mode
indicator
LINE STRAIGHT Tuning mode
indicator indicator
SURROUND indicator | Tape 2
indicator
TUNED indicator
MEMORY indicator
15 re 1 3 J
@ TONE control knobs @® PHONES jack
€ Numeric keys Used for headphone listening.
€
Remote
control
sensor
@)
SPEAKERS
A/B
keys
@
THEATER
LOGIC
indicator
Press
to
select
the
A
and/or
B
speaker
@ STAND BY indicator systems.
@
BAND
key
«B
THEATER
LOGIC
key
Press to switch the broadcast band. @ LOUDNESS key
@
TUNING
keys
Press
to
enhance
low
frequencies.
@ P.CALL key @® DOLBY PRO LOGIC key
©
AUTO
key
@)
CENTER
MODE
key
@
DIRECT
key
Press
to
select
the
center
mode
of
the
s : DOLBY PRO LOGIC surround play.
t
ee ane station tuning based on @ DOLBY 3 STEREO key
(PVOLUME
CONTROL
knob
@
CENTER
LEVEL
key
(PPOWER
key
@
BYPASS
key
Press to cancel the surround modes.
#4 REAR LEVEL key
@ LINE STRAIGHT key
Press to reproduce the source with
higher sound quality.
@) DELAY TIME key
Press to adjust delay time.
@ TAPE 2 {MONITOR} key
’ & INPUT SELECTOR knob
Turn to select the Input sources.
@ MEMORY key
Press to preset a station in the memo
BALANCE contro! knob
Turn to adjust the volume balance |
tween left and right.
When
the
power
cord
of
this
system
is
plugged
into
an
AC
outlet,
the
STAND
BY
indicator
lights
up
regardless
of
the
ON/OFF
setting
of
the
POW:
switch.
This
indicates
that
a
small
amount
of
current
is
being
supplied
to
the
unit
to
back
up
the
memory
contents.
This
mode
is
referred
to
as
t
Stand
By
mode.
While
the
STAND
BY
indicator
is
lit,
the
power
of
the
system
can
be
switched
ON/OFF
from
the
remote
control
unit.

The
remote
control
unit
provided
with
the
receiver
can
also
contro
receiver
through
system
control
cords.
For
details
of
the
controllable
functions,
components.
Cassette deck operation keys
These keys are used to operate TAPE
A and TAPE B decks.
REC/ARM: ;
When recording on TAPE 8,
puts the deck in record-pause
mode after leaving a non-re- &
RIPE Ne ne RP ay
CD player operation keys
DISC: This key is used as the disc se-
lector of a multi-CD player.
Each press selects a different
disc.
INPUT key
Selects the input sources.
TAPE 2 {MONITOR) key
Press to monitor the source being
recorded.
8 bie ERT Tt aia tt LA
POWER key «
MUTE key
Mutes the sound temporarily.
VOLUME CONTROL keys
Adjust the listening volume. The VOL-
UME CONTROL knob of the main unit
turns when these keys are operated,
In this case, the indicator on the knob
blinks at high speed.
corded blank of 4 seconds. 3
tae
ai ev
KENWOOD
REMOTE CONTROL UNIT
RC-RO702
Model: RC-R0702
infrared ray system
; VOLYME CONTROL ]
pl
TUNER operation keys
BAND:
Selects the broadcast band.
P.CALL;
Recalls preset stations.
DIRECT:
Used in combination with the
numeric keys for direct tuning
of stations.
Numeric keys
When the CD input is selected, func-
tion as the numeric keys of the CD
player.
When
the
TUNER
input
is
se-
|
lected,
function
as
the
numeric
keys
§
of
the
tuner.
SURROUND keys
SURROUND MODE: :
Switches the surround modes.
TEST TONE:
Switches the test tone ON and
OFF.
CENTER + MULTI LEVEL CONTROL:
This combination adjusts the
center level.
REAR + MULTI LEVEL CONTROL:
Adjusts the rear level.
DELAY + MULTI LEVEL CONTROL:
Adjusts the delay time.
|
KENWOOD
cassette
decks
and
CD
player
connected
to
the
@:
refer
to
the
instruction
manuals
of
these

PSII Pe ODT AG Ald Neh o bs raeweawh reteve LT te
e Insert two AA-size (R6 / SUM-3} batteries as indicated by the polar
ity marking.
Operation procedure
‘ ‘ tate .. ‘ Picea gt eens coven cc iteen Signs .
Net EAA Rat ANA MANE at ANA I A ET ATE a Sale EN NN TG NN CN TN Cale a Nee PTO ae NT
Plug the power cord of the system into an AC wall outlet, and
press the POWER key on the remote control unit to turn the
power on. When the power is turned on, press the key of the
source component to be operated.
Remote sensor
ee eee
e@ When two operation keys on the remote controi unit are presse:
successively, press each key securely reserving an interval of mar:
than 1 second for each press.
Model: RC-R0702 e AL i connected via the system control cards, such as th:
infrared ray system D player, can also be remote-controlled, In this case, please rear
the instruction manual supplied with your component.
1. The supplied batteries are intended for use in operation checks. Therefore, their lives may be shorter than ordinary batteries.
2. When the remote-controllable distance gets shorter than before, replace both batteries with new ones.
3. Malfunction may occur if direct sunlight or the light of a high-frequency lighting fluorescent lamp enters the remote control light
sensor. In such a case, change the system installation position to prevent the malfunction.

7 Turn the power OWN.
The indicators of the speaker
systems to be used should light up.
3 Select the input source.
Veeen
ee
ped
cane
eR
REE
es
PERCE
PERNA
SE
EEN
MEAN
ETErTy
Heme
eR
ER
ERE
Ee
REE
TR
ET
SNS
Pred
A, B OFF
Sound
is
not
output
from
the
speakers.
Use
this
setting
for
listen-
ing through headphones, etc.
AON
Sound
is
output
from
the
speakers
connected
to
the
SPEAKERS
A
terminals on the rear panel.
BON
Sound
is
output
from
the
speakers
connected
to
the
SPEAKERS
B
terminals on the rear panel.
A, B ON
Sound
is
output
from
the
speakers
connected
to
the
SPEAKERS
A
and B terminals on the rear panel.
e
When
a
surround
mode
is
activated
while
both
SPEAKERS
A
and
B
are
ON,
the
SPEAKERS
B
system
is
automatically
switched
off.
If
the
SPEAKERS
B
key
is
pressed
at
this
time,
the
SPEAKERS
B
sys-
tem
is
switched
ON
and
the
SPEAKERS
A
system
is
switched
OFF
automatically.
e
if
the
cassette
deck(s),
CD
player
and/or
turntable
is
connected
through
system
contro!
cords,
the
component
of
the
selected
input
source
Starts
to
play
automatically.
The input sources are switched in
the following order:
(TUNER (frequency display)
The selected source is displayed.
@TAPE 1
@ VIDEO 1
@VIDEO
2
[
i
@®cD
L
Lf
®PHONO
@
The
selected
input
source
is
held
in
memory
for
about
3
days
even
after
the
power
cord
is
unplugged
from
the
mains
outlet.
e
The
sound
of
input
source
cannot
be
listened
to
while
TAPE
2
is
ON.
@
When
the
volume
is
adjusted
from
the
remote
contro!
unit,
the
indi-
cator
on
the
VOLUME
CONTROL
knob
blinks.

See L RE ORENGE sane te
she
n Mlestia the te tone
To 52 iw To aajiiee high
frequencies frequencies
Adjusting the je letright sound balance
(fr
oe
To
decrease
©
;
10
decrease
the
Seo the right teft sound
sound
Wrrrerererrrrrertretierirritrtrrrtr er titi err
Using the LOUDNESS key
When listening at a low volume, the loudness function allaws to com-
pensate the low frequencies which human ears have GieuIty in hear-
ing at a low volume.
') (LGUDNESS
yA |
To cancel the loudness function
Press the key again.
Remote control unit only
MUTE
® The indicator on the VOLUME CONTROL of the main unit blinks.

a erp
@ Plug headphones.
PHONES
To increase volume
main unit
EE I LG NNN NM NE OLE MN MM OEM ot AMY oll NA
Line-straight playback
This feature allows to enjoy music sources such as CD with an even
higher sound quality.
G) Select the source to be played.
as
@) Press the LINE STRAIGHT key.
@) Play the source.
@ The tone control functions are defeated during line-straight play.
@ The line-straight play is cancelled when a key associated with sur-
round play is pressed. :
To cancel
Press the key again.
Goes off
ee |

6
‘oo ee Siege 9
“ithatitene nit *
he A Aa AN Be TAN NbSacait, Medes MOM oP e ken veelilttel let ket inp ipete teeters: Seeders Mpedsipetaniyeeael th :
To record a music source
@ Setect the source to be recorded.
INPUT SELECTOR
Select an input source
other than TAPE 1.
@Put the cassette deck in record- ;
pause mode. 4
@ Play the source and start recording.
wee eer et Eerere rT Cy CEP er ree erererstrricccler cc irr tte ce er eer cre Perse er eee es sees tie ce Serer ee eee creer er reece ere ees!
@ Select a source other than TAPE 1.
INT SELECTOR
@ Play cassette deck 2 and start re- :
cording on cassette deck 1. : ® For copying a tape using a double cassette deck, read the instruc-
Q tion manual of the double cassette deck.
Seer ee mE ETT ee PP Re PE RETR NSE OTTER SRA EPP PSE ESE R ERR LEER
Cetag tape , aye d deb siig TAPE 1 — TAPE 2)
Play the cassette deck connected to the TAPE 1 jacks and start
Miakbebreltt of the cassette deck connected to the TAPE 2 ostiseh
Sinchie seearding
By connecting this unit to a CD player or turntable manufactured by KENWOOD through a system control cord, the CD or analog disc sound can be
recorded with a simple operation on the cassette deck{s).
Select the music source to be recorded with the INPUT SELECTOR and put the cassette deck in record-pause mode. With this condition, press the
play key of the CD player or turntable to start recording at the same time.as the source component Starts to play.

BAND NEMOAY ©
The input sources are switched in the following order:
TUNER {frequency display)
@TAPE 1 Frequency display
@VIDEO 1
@VIDEO 2
@®cp
@®PHONO it rT
f Lf Hy | kHz
@ The fast frequency tuned before is displayed.
slhienilintenienete taelhtete eh hee tLe TEE TE Prey
Each press switches the band as follows:
a Ga FM
@ AM AM or EM indicator
aaah tactical Le LTTE ELT TET TTT TTP TTT Eee eee eee
‘Each press switches the turning method as follows:
" © AUTO lit (auto tuning)
@ AUTO not lit
(manual turning)
e Usually, set the switch to AUTO [auto tuning).
Select manual tuning when noise interferes due to weak radio wave.
(The stereo broadcasting is received in monaural during manual
tuning.)
TS Orie ae re RE RE eT OEE ee RR E Ree ee SE ROT ee ee Re em EO bh
Frequency display
“TUNED” lights up when
4 station is turned.
Auto tuning: The next station found is tuned automatically.
Manual tuning: Press repeatedly or hold until a station is tuned.

_..Receiving radio station by specifying its frequency _
7 a : - The input sources are switched in the following order:
7 Select the TUNER input. : (TUNER (frequency display)
‘3 @TAPE 1 ;
@VIDEO 4 Frequency display
@®VIDEO 2
®CbD
©PHONO i ] TT
[LI | KHz
Each press switches the band as follows: .
i () FM
@ AM AM or FM indicator
BAND MEMORY DIRECT
‘ 3 Press the numeric keys according to the frequency to be tuned as
Specify the frequency. E shown below. ;
: AM 810 kHz........ 8,1,0 (9 kHz space)
@ Press the DIRECT key. 8, 1 (10 kHz space)
AM 1260 kHz.......7, 2, 8, O (9 kHz space)
skin Havacae cakes 1,2,6 (10 kHz space)
FM 90 MHz......... §,90,0, 9 (50 kHz space)
§,0,0 (100 kHz space}
FM 102.5 MHz ....1, 0, 2, 5, O (50 kHz space)
1,0,2,6 (100 kHz space)
Frequency display
TUNED lights up when
a station is tuned.
@ Enter the frequency of the desired
station.
1 z 3 4 &
e If you make a mistake, repeat step 3 again

Preparation
e Tune the station to be stored
RR AE A
Fasc neh RAN Pehl nine Sha See Taso ne PARRA RMA lieihienmninnee DTT
reset) _
Lights up (for 5 sec.)
BAND MEMORY OIRECT
SAMBA
ens Proceed to step 2 within 5 sec.| 7 Be —* "
(If more than 5 sec, have elapsed, press the MEMORY key again.}
Press the numeric keys in the following order.
To store in “15” a. +10,5
2 Select one of the preset numbers from 1 to 20. 16 scree, +10 +10.0
LC i__* i e Repeat steps 1 and 2 for each of the stations to be stored in
memory, ~.* : :
e |f a station is stored in a preset number which already stores a sta-
tion memory under it, the previous memory is replaced by the new
memory content.
e@ Once the memory content_has been preset, it is held for about 3
Pasa ee Hc EET LTE eee ne Eee et eee TET TTT
‘i days even after the power cord is unplugged from the mains outlet,
Press the preset number of the desired station.
@ Select the TUNER input with the §
INPUT SELECTOR. 2
IMT BELECTOR
Press the numeric keys in the following order.
To recall “15” .........0 _+10, 5
To recall “20” +10, +10, 0
MAE EO Ree eran
Set E TE Lat hee Carnet tient
_ Receiving all preset stations in order.
Press the P.CALL key.
e Every time the key is pressed, the next station in the order of the
preset number is received.
If the key is held pressed ......, Preset stations will be received suc-
cessively for about half a second each.
ir

- For the connections and operations, also read carefully the
2 instruction manuals of the video components. ., a
The input sources are switched in the following order:
(TUNER (frequency display)
@TAPE 1
@VIDEO 1 “VIDEO 1” should be displayed.
@VIDEO 2
@®CcD
@©PHONO ve Mi deg i
@ Select the input to which a video deck is connected.
Pee ere rere rt Loge te rer eer reer rere |
® Connect the component ta be played to the VIDEO 2 jacks.
@ The connectable components include a video deck (playback only},
video camera (playback only), LD player or DBS tuner.
The input sources are switched in the following order:
CD TUNER (frequency display)
@TAPE 1
@VIDEO 1 “VIDEO 2” should be displayed.
@VIDEO 2
© PHONO b 7 ff ie i rm
PPP PPP cer Str or reece rer eee er ree er cer et eeerereererrere tre srer irr cr cre rrrer rr cerererr re rre re rrr rs?
ttt Pere ee PEE hPL EL eT TE ee eee rere ere eer ec cee Pee er rrr ccc r eer er cece errr)
e@ Start recording with the video deck which is connected to the VIDEO
1 jacks.