Kenwood Nexedge NX-5200 User manual

.
.
NX-5000 series
USER GUIDE
GUIDE DE L’UTILISATEUR
GUÍA DEL USUARIO
.
.
B5A-0049-10 (K)

VHF DIGITAL TRANSCEIVER
NX-5200
UHF DIGITAL TRANSCEIVER
NX-5300
700/800MHz DIGITAL TRANSCEIVER
NX-5400
USER GUIDE
The AMBE+2™ voice coding Technology embodied in
this product is protected by intellectual property rights
including patent rights, copyrights and trade secrets of
Digital Voice Systems, Inc. This voice coding
Technology is licensed solely for use within this
Communications Equipment. The user of this
Technology is explicitly prohibited from attempting to
extract, remove, decompile, reverse engineer, or
disassemble the Object Code, or in any other way
convert the Object Code into a human-readable form.
U.S. Patent Nos. #6,199,037, #6,912,495, #8,200,497,
#7,970,606 and #8,359,197
.
SD™ and microSD™ are trademarks of SD-3C, LLC in the United
States and/or other countries.
The Bluetooth® word mark and logo are registered trademarks
owned by the Bluetooth SIG, Inc. and any use of such marks by
JVC KENWOOD Corporation is under license. Other trademarks
and trade names are those of their respective owners.
Firmware Copyrights
The title to and ownership of copyrights for firmware embedded in
KENWOOD product memories are reserved for JVC KENWOOD
Corporation.

THANK YOU
We are grateful you have chosen KENWOOD for your Digital
Transceiver applications.
This User Guide covers only the basic operations of your
radio. Ask your dealer for information on any customized
features they may have added to your radio. For using
details User Manual, refer to the following URL.
http://manual2.jvckenwood.com/en_contents/search/
CONTENTS
NOTICES TO THE USER ........................................................................................ 3
PRECAUTIONS ....................................................................................................... 5
TERMINAL DESCRIPTIONS ................................................................................ 12
UNPACKING AND CHECKING EQUIPMENT ...................................................... 13
SUPPLIED ACCESSORIES ................................................................................ 13
PREPARATION ..................................................................................................... 14
INSTALLING/ REMOVING THE (OPTIONAL) BATTERY PACK ......................... 14
INSTALLING THE (OPTIONAL) ANTENNA ........................................................ 15
INSTALLING THE BELT CLIP ............................................................................. 15
INSTALLING THE CAP OVER THE UNIVERSAL CONNECTOR ....................... 16
INSTALLING THE (OPTIONAL) SPEAKER/ MICROPHONE OR HEADSET ...... 16
INSTALLING THE microSD MEMORY CARD .................................................... 17
ORIENTATION ...................................................................................................... 18
KEYS AND CONTROLS ..................................................................................... 18
DISPLAY ............................................................................................................. 21
BASIC OPERATIONS ........................................................................................... 24
SWITCHING POWER ON/ OFF .......................................................................... 24
ADJUSTING THE VOLUME ................................................................................ 24
SELECTING A ZONE AND CHANNEL ............................................................... 24
TRANSMITTING ................................................................................................. 25
RECEIVING ......................................................................................................... 25
INFORMATION ON SOFTWARE LICENSE ......................................................... 26
2

NOTICES TO THE USER
●Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
●Illegal operation is punishable by fine and/or imprisonment.
●Refer service to qualified technicians only.
Safety: It is important that the operator is aware of, and understands,
hazards common to the operation of any transceiver.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless
the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY
THE FCC
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However,
there is no guarantee that the interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and receiver.
●Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
●Consult the dealer for technical assistance.
3

The RBRC Recycle seal found on KENWOOD
nickel metal hydride (Ni-MH) battery packs
indicates KENWOOD ’s voluntary
participation in an industry program to collect
and recycle Ni-MH batteries after their
operating life has expired. The RBRC program
is an alternative to disposing Ni-MH batteries
with your regular refuse or in municipal waste
streams, which is illegal in some areas.
For information on Ni-MH battery recycling in your area, call (toll free)
1-800-8-BATTERY (1-800-822-8837).
KENWOOD’s involvement in this program is part of our commitment to
preserve our environment and conserve our natural resources.
The RBRC Recycle seal found on KENWOOD
lithium-ion (Li-ion) battery packs indicates
KENWOOD’s voluntary participation in an
industry program to collect and recycle Li-ion
batteries after their operating life has expired.
The RBRC program is an alternative to
disposing Li-ion batteries with your regular
refuse or in municipal waste streams, which is
illegal in some areas.
For information on Li-ion battery recycling in your area, call (toll free)
1-800-8-BATTERY (1-800-822-8837).
KENWOOD’s involvement in this program is part of our commitment to
preserve our environment and conserve our natural resources.
This device complies with Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this
device may not cause interference, and (2) this device must accept any
interference, including interference that may cause undesired
operation of the device.
Under Industry Canada regulations, this radio transmitter may only
operate using an antenna of a type and maximum (or lesser) gain
approved for the transmitter by Industry Canada. To reduce potential
radio interference to other users, the antenna type and its gain should
be so chosen that the equivalent isotropically radiated power (e.i.r.p.)
is not more than that necessary for successful communication.
4

PRECAUTIONS
●Do not charge the transceiver and battery pack when they are wet.
●Ensure that there are no metallic items located between the transceiver
and the battery pack.
●Do not use options not specified by KENWOOD.
●If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts.
●If a headset or headphone is connected to the transceiver, reduce the
transceiver volume. Pay attention to the volume level when turning the
squelch off.
●Do not place the microphone cable around your neck while near
machinery that may catch the cable.
●Do not place the transceiver on unstable surfaces.
●Ensure that the end of the antenna does not touch your eyes.
●When the transceiver is used for transmission for many hours, the
radiator and chassis will become hot. Do not touch these locations
when replacing the battery pack.
●When water gets into the microphone opening or the speaker grill, the
voice level may become incoherent or distorted. Lightly shake the
transceiver to remove the water from the speaker and/or microphone
before operating the transceiver.
●Always switch the transceiver power off before installing optional
accessories.
5

WARNING
Turn the transceiver power off in the following locations:
●Near explosives or blasting sites.
●In aircraft. (Any use of the transceiver must follow the instructions
and regulations provided by the airline crew.)
●Where restrictions or warnings are posted regarding the use of
radio devices, including but not limited to medical facilities.
●Near persons using pacemakers.
Turn the transceiver power off in the following locations, unless
the model is specifically qualified for such use (Intrinsically Safe
such as approved by Factory Mutual, CSA):
●In explosive atmospheres (inflammable gas, dust particles, metallic
powders, grain powders, etc.).
●While taking on fuel or while parked at gasoline service stations.
WARNING
●Do not remove the black sheet from the reverse side of the
transceiver (refer to the illustration below). Removal of this sheet
decreases the waterproof efficiency of the transceiver and may
cause malfunctions if water seeps into the transceiver.
●The orange seal on the reverse side of the transceiver is important
with respect to the waterproof efficiency of the transceiver. Do not
place stickers or other materials on or around the seal shown in the
figure, or on the reverse side of the battery pack. Doing so will impair
the waterproof efficiency of the transceiver and may cause it to
break down. Additionally, in order to prevent damage to the seal,
do not allow it to come in contact with foreign materials.
6

CAUTION
●Do not disassemble or modify the transceiver for any reason.
●Do not place the transceiver on or near airbag equipment while the
vehicle is running. When the airbag inflates, the transceiver may be
ejected and strike the driver or passengers.
●Do not transmit while touching the antenna terminal or if any metallic
parts are exposed from the antenna covering. Transmitting at such
a time may result in a high-frequency burn.
●If an abnormal odor or smoke is detected coming from the
transceiver, or the transceiver seems to malfunction, switch the
transceiver power off immediately, remove the battery pack from
the transceiver, and contact your KENWOOD dealer.
●Use of the transceiver while you are driving may be against traffic
laws. Please check and observe the vehicle regulations in your
area.
●Do not expose the transceiver to extremely hot or cold conditions.
●Do not carry the battery pack (battery case) with metal objects, as
they may short the battery terminals.
●Danger of explosion if the battery is incorrectly replaced; replace
only with the same type.
●To dispose of batteries, be sure to comply with the laws and
regulations in your country or region.
●When attaching a commercial strap to the transceiver, ensure that
the strap is durable. In addition, do not swing the transceiver around
by the strap; you may inadvertently strike and injure another person
with the transceiver.
●If a commercially available neck strap is used, take care not to let
the strap get caught on nearby machine.
●When operating the transceiver in areas where the air is dry, it is
easy to build up an electric charge (static electricity). When using
an earphone accessory in such conditions, it is possible for the
transceiver to send an electric shock through the earphone and to
your ear. We recommend you use only a speaker/microphone in
these conditions, to avoid electric shocks.
7

Information concerning the battery pack:
The battery pack includes flammable objects such as organic solvent.
Mishandling may cause the battery to rupture producing flames or
extreme heat, deteriorate, or cause other forms of damage to the battery.
Please observe the following prohibitive matters.
DANGER
●Do not disassemble or reconstruct the battery!
The battery pack has a safety function and protection circuit to avoid
danger. If they suffer serious damage, the battery may generate
heat or smoke, rupture, or burst into flame.
●Do not short-circuit the battery!
Do not join the + and – terminals using any form of metal (such as
a paper clip or wire). Do not carry or store the battery pack in
containers holding metal objects (such as wires, chain-necklaces
or hairpins). If the battery pack is short-circuited, excessive current
will flow and the battery may generate heat or smoke, rupture, or
burst into flame. It will also cause metal objects to heat up.
●Do not incinerate or apply heat to the battery!
If the insulator is melted, the gas release vent or safety function is
damaged, or the electrolyte is ignited, the battery may generate
heat or smoke, rupture, or burst into flame.
●Do not leave the battery near fire, stoves, or other heat
generators (areas reaching over 80°C/ 176°F)!
If the polymer separator is melted due to high temperature, an
internal short-circuit may occur in the individual cells and the battery
may generate heat or smoke, rupture, or burst into flame.
●Avoid immersing the battery in water or getting it wet by other
means!
If the battery becomes wet, wipe it off with a dry towel before use.
If the battery’s protection circuit is damaged, the battery may charge
at extreme current (or voltage) and an abnormal chemical reaction
may occur. The battery may generate heat or smoke, rupture, or
burst into flame.
8

DANGER
●Do not charge the battery near fire or under direct sunlight!
If the battery’s protection circuit is damaged, the battery may charge
at extreme current (or voltage) and an abnormal chemical reaction
may occur. The battery may generate heat or smoke, rupture, or
burst into flame.
●Use only the specified charger and observe charging
requirements!
If the battery is charged in unspecified conditions (under high
temperature over the regulated value, excessive high voltage or
current over regulated value, or with a remodeled charger), it may
overcharge or an abnormal chemical reaction may occur. The
battery may generate heat or smoke, rupture, or burst into flame.
●Do not pierce the battery with any object, strike it with an
instrument, or step on it!
This may break or deform the battery, causing a short-circuit. The
battery may generate heat or smoke, rupture, or burst into flame.
●Do not jar or throw the battery!
An impact may cause the battery to leak, generate heat or smoke,
rupture, and/or burst into flame. If the battery’s protection circuit is
damaged, the battery may charge at an abnormal current (or
voltage), and an abnormal chemical reaction may occur.
●Do not use the battery pack if it is damaged in any way!
The battery may generate heat or smoke, rupture, or burst into
flame.
●Do not solder directly onto the battery!
If the insulator is melted or the gas release vent or safety function
is damaged, the battery may generate heat or smoke, rupture, or
burst into flame.
●Do not reverse the battery polarity (and terminals)!
When charging a reversed battery, an abnormal chemical reaction
may occur. In some cases, an unexpected large amount of current
may flow upon discharging. The battery may generate heat or
smoke, rupture, or burst into flame.
9

NOTIFICATION OF WATER-RESISTANT MODEL
Water Resistance and Maintenance
Water-Resistant Model transceiver conforms to the following standards.
Immersion: The transceiver retains its water resistant capabilities
outlined in U.S. Military Standards when submersed in water at a depth
of 1 meter (3.28 feet) for 2 hours.
IP67/ IP68: The IP standard is the protection level specified by the
international standard IEC 60529. The first numeral indicates the “dust-
resistant level” and the second numeral indicates the “water-resistant”
level.
Note:
●Initial water-resistant tests and procedures are performed products
upon being ordered from KENWOOD.
PRECAUTIONS
●The applicable standards listed above do not assure that the
transceiver can be used in water. The transceiver may be damaged in
a situation in which the maximum depth is over 1 meter or the maximum
submersion time exceeds 2 hours.
●Observe the following precautions to maintain the transceiver’s water-
resistant performance:
a) Do not drop or apply strong physical shocks to the transceiver.
b) Do not disassemble or attempt to modify the transceiver. (If it is
disassembled or modified, its performance is not guaranteed.)
c) Do not soak the transceiver in water that contains a solvent or
surfactant, such as detergent or alcohol.
●If it is soaked in muddy water or salt water (including sea water), it may
become corroded. Immediately flush with fresh water and then wipe
dry with a soft cloth.
●If water is splashed onto the microphone, the battery, or the antenna
terminal, clean and dry them with a soft cloth before reconnecting to
the transceiver.
●When water gets into the microphone opening or the speaker grill, the
voice level may become low or distorted. Lightly shake the transceiver
to remove the water from the speaker and/or microphone before
operating the transceiver.
●Use of any option on the transceiver not specified by KENWOOD, may
reduce or void the water resistant and dust resistant performance.
10

DANGER
●Do not reverse-charge or reverse-connect the battery!
The battery pack has positive and negative poles. If the battery pack
does not smoothly connect with a charger or operating equipment,
do not force it; check the polarity of the battery. If the battery pack
is reverse-connected to the charger, it will be reverse-charged and
an abnormal chemical reaction may occur. The battery may
generate heat or smoke, rupture, or burst into flame.
●Do not touch a ruptured and leaking battery!
If the electrolyte liquid from the battery gets into your eyes, wash
your eyes with fresh water as soon as possible, without rubbing your
eyes. Go to the hospital immediately. If left untreated, it may cause
eye-problems.
WARNING
●Do not charge the battery for longer than the specified time!
If the battery pack has not finished charging even after the regulated
time has passed, stop it. The battery may generate heat or smoke,
rupture, or burst into flame.
●Do not place the battery pack into a microwave or high
pressure container!
The battery may generate heat or smoke, rupture, or burst into
flame.
●Keep ruptured and leaking battery packs away from fire!
If the battery pack is leaking (or the battery emits a bad odor),
immediately remove it from flammable areas. Electrolyte leaking
from battery can easily catch on fire and may cause the battery to
generate smoke or burst into flame.
●Do not use an abnormal battery!
If the battery pack emits a bad odor, appears to have different
coloring, is deformed, or seems abnormal for any other reason,
remove it from the charger or operating equipment and do not use
it. The battery may generate heat or smoke, rupture, or burst into
flame.
11

TERMINAL DESCRIPTIONS
Universal connector
It is possible to use a resin-based cover for the Universal
connector.
Pin No. Name I/O Description Specification
1 SSW I Ext/ Int Speaker Switch
Input Hi: INT, Low: EXT
2 SP+ O BTL Output + for External
Speaker Standard load 8 K
3 SP- O BTL Output – for External
Speaker Standard load 8 K
4 MSW I Ext/ Int MIC Switch Input Hi: INT, Low: EXT
5 EMC I External MIC Input Impedance: 1.8 kK
6 ME - External MIC GND -
7 PTT I External PTT Input Low: PTT ON
8 PF I Programmable Function
Key Input Input voltage: 0 V - 3.3 V
9 OPT I/O Aux I/O Port (for EXT
Option)
I: 0 V - 3.3 V
O: Standard load 25 kK
10 E - GND GND
11 5V O 5 V 5 V power supply output
Max output current: 140 mA
12 TXD O Serial Data Output Baud rate: 115200 bps max
13 RXD I Serial Data Input Baud rate: 115200 bps max
14 EMC I External MIC input Impedance: 1.8 kK
Antenna Terminal
50 K impedance
12

UNPACKING AND CHECKING EQUIPMENT
Note:
●The following unpacking instructions are for use by your KENWOOD
dealer, an authorized KENWOOD service facility, or the factory.
Carefully unpack the transceiver. We recommend that you
identify the items listed below before discarding the packing
material. If any items are missing or have been damaged during
shipment, file a claim with the carrier immediately.
SUPPLIED ACCESSORIES
Belt clip ................................................................................................. 1
●Screws for belt clip (M3 x 8 mm) ..................................................... 2
Universal connector cap ....................................................................... 1
●Dressing screw ............................................................................... 1
●Packing (preassembled) ................................................................. 1
User Guide ........................................................................................... 1
13

PREPARATION
INSTALLING/ REMOVING THE (OPTIONAL) BATTERY
PACK
CAUTION
●Do not short the battery terminals or dispose of the battery by fire.
●Never attempt to remove the casing from the battery pack.
●Install the battery pack after cleaning the battery pack contacts and
the transceiver terminals.
●Before charging a battery pack that is attached to the transceiver,
ensure that the safety catch is firmly closed.
.
●If the release latch is tilted and the battery pack
is not attached to the transceiver, return the
release latch to its original position using your
finger.
Release latch
1Match the guides of the battery pack with the corresponding
grooves on the upper rear of the transceiver, then firmly press
the battery pack to lock it in place.
Check that the release latch is firmly locked.
2Lock the safety catch to prevent accidentally pressing the
release latch and removing the battery pack.
3To remove the battery pack, lift the safety catch, press the
release latch, then pull the battery pack away from the
transceiver.
1
2
3
Release latch
Safety catch
14

INSTALLING THE (OPTIONAL) ANTENNA
.
Screw the antenna into the connector
on the top of the transceiver by
holding the antenna at its base and
turning it clockwise until secure.
.
INSTALLING THE BELT CLIP
.
If necessary, attach the belt clip using
the two supplied M3 x 8 mm binding
screws.
Note:
●If the belt clip is not installed, its
mounting location may get hot during
continuous transmission or when left
sitting in a hot environment.
CAUTION
Do not use glue which is designed to prevent screw loosening when
installing the belt clip, as it may cause damage to the transceiver.
Acrylic ester, which is contained in these glues, may crack the
transceiver’s back panel.
Optional
antenna
Belt clip
M3 x 8 mm
screws
15

INSTALLING THE CAP OVER THE UNIVERSAL
CONNECTOR
.
1If you are not using an optional
speaker/ microphone or
headset, install the cap over
the universal connector.
2Secure the cap in place using
the dressing screw.
.
INSTALLING THE (OPTIONAL) SPEAKER/ MICROPHONE
OR HEADSET
1Insert the guide of the speaker/ microphone or headset
connector into the groove of the universal connector.
2Secure the connector in place using the attached screw.
Optional speaker/
microphone
Note:
●When not using an optional speaker/ microphone or headset, install
the cap over the universal connector.
●The noise canceling function on KMC-54WD Speaker Microphone
works using the built-in DSP of the transceiver, and can only be used
with NX-5000 series Portable models.
Universal
connector cap
16

INSTALLING THE microSD MEMORY CARD
.
1Remove the battery pack.
2Open the cap.
3Insert the microSD memory
card.
●Insert the microSD memory
card with its terminal side
facing the same side as the
front of the transceiver.
●Insert the microSD memory
card until it clicks into place.
●To remove the microSD
memory card, push the card
inwards once, then pull it out
straight.
.
Note:
●microSD memory cards (Class 2 or higher) and microSDHC memory
cards (Class 2 or higher) can be used.
●SDXC memory cards cannot be used.
●This transceiver is not guaranteed to operate with all microSD
memory cards.
(Operations are confirmed on memory cards for the following brands:
SanDisk, TOSHIBA and Panasonic.)
●Use the microSD memory card within the allowable operating
temperature.
●Do not remove the microSD memory card or turn off this transceiver
while the microSD memory card is being accessed.
●The waterproof performance is not guaranteed if the microSD
memory card slot cap is not fit into place.
●Make sure your hands are clean before opening the microSD memory
card slot cap.
Compensation Disclaimer
Data stored on the microSD memory card may be altered or lost due to
problems with this transceiver. We do not accept liability in respect of
the data stored on your microSD memory card, failure to save the data
properly, loss of data, and any direct or indirect damages.
Cap
microSD
memory card
17

ORIENTATION
KEYS AND CONTROLS
Speaker
Microphone
Full Key model
Standard Key
model
microSD memory
card slot
APower switch/ Volume control
Turn clockwise to switch the transceiver ON. To switch the transceiver
OFF, turn counterclockwise fully. Rotate to adjust the volume level.
BSelector knob
Rotate this control to activate its programmable function. The default
setting is Channel Select.
18