Kenwood TS-990S User manual
©B62-2389-40
09 08 07 06 05 04
HF/50 MHzTRANSCEIVER
TS-990S
INSTRUCTION MANUAL
1.05
I
PRIORTOYOUR FIRST QSO
IndexContents
Thank you for purchasing thisTS-990S transceiver.
This chapter, Prior to your first QSO, gives you a product
overview, conditions of your use, notations applied to
this manual and safety precautions.Prior to your first
QSO, carefully read through the following precautions to
become familiar with the safety precautions applicable to
this transceiver.
After reading through this instruction manual, store it with
the warranty card and packing materials.
FEATURES
• A main receiver with a class-leading +40 dBm third-order IP and a
sub receiver which incorporates theTS-590S receiver architecture.
Capable of receiving two signals at once, in different bands.
• 7-inch wide and 3.5-inch colorTFT displays can show independent
contents.
• Covers the HF and 50 MHz bands.
• Clean 5 to 200W transmit power through the 50V FET final unit.
• High-speed relay-driven automatic antenna tuner built-in allows fast
tuning.
• Built-in Baudot RTTY, PSK31, Demodulator and Modulator for
PSK63.
• Compliant with SSB, CW, FSK, PSK (QPSK31, BPSK31, BPSK63),
AM, and FM Modes.
• Three Analog Devices 32-bit floating-point arithmetic DSPs.
• Equipped as standard with USB, Serial and LAN ports.
• Video signal output for display by an external PC (main screen
display only).
• Various PC applications (free software):ARCP-990 enabling PC
control, ARHP-990 enabling remote control, and ARUA-10 enabling
the USB audio interface.
SUPPLIED ACCESSORIES
The following accessories are supplied with the
transceiver.After carefully unpacking the transceiver,
identify the accessories listed in the table.
Description Quantity
AC Power Cable UL plug (K-type only) 1
BS plug (E-type only) 1
CE plug (E-type only) 1
7-pin DIN plug 1
13-pin DIN plug 1
Fuse 4 A for an external antenna tuner 1
Instruction Manual 1
Warranty Card 1
Circuit Diagram 4
Line Filter (E-type only) 1
MARKET CODES
K-type: The Americas
E-type: Europe
The market code is shown on the carton box.
• The AC power cable supplied with the product is suitable for AC
120V(K-type) or AC 220V-240V (E-type)
• Do not use a power cable other than supplied with this product.
NOTICE TO THE USER
One or more of the following statements may be
applicable for this equipment.
FCCWARNING
This equipment generates or uses radio frequency energy.Changes
or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction
manual.The user could lose the authority to operate this equipment if an
unauthorized change or modification is made.
INFORMATIONTOTHE DIGITAL DEVICE USER
REQUIRED BYTHE FCC
This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to Part 15 of the FCC Rules.These
limits are designed to provide reasonable protection against harmful
interference in a residential installation.
This equipment generates, uses and can generate radio frequency
energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.However,
there is no guarantee that the interference will not occur in a particular
installation.If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
•Reorientorrelocatethereceivingantenna.
•Increasetheseparationbetweentheequipmentandreceiver.
•Connecttheequipmenttoanoutletonacircuitdifferentfromthatto
which the receiver is connected.
•Consultthedealerfortechnicalassistance.
Information on Disposal of Old Electrical and Electronic Equipment and
Batteries (applicable for countries that have adopted separate waste
collection systems)
Products and batteries with the symbol (crossed-out wheeled
bin) cannot be disposed as household waste.
Old electrical and electronic equipment and batteries should
be recycled at a facility capable of handling these items and
their waste byproducts.
Contact your local authority for details in locating a recycle
facility nearest to you.
Proper recycling and waste disposal will help conserve
resources whilst preventing detrimental effects on our health
and the environment.
This device complies with Industry Canada license-
exempt RSS standard(s).Operation is subject to the
following two conditions :(1) this device may not cause
interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.
NOTIFICATION
This equipment complies with the essential requirements of
Directive 1999/5/EC.
The use of the warning symbol means the equipment is
subject to restrictions of use in certain countries.
This equipment requires a license and is intended for use in the
countries below.
AT BE DK FI FR DE GR IS
IE IT LI LU NL NO PT ES
SE CH GB CY CZ EE HU LV
LT MT PL SK SI BG RO HR
ISO3166
This product is designed for connection to an IT power
distribution system.
PRIORTOYOUR FIRST QSO
II Index Contents
Buürün26891sayılıResmiGazete’deyayımlananElektrikli
veElektronikEşyalardaBazıZararlıMaddelerinKullanımının
SınırlandırılmasınaDairYönetmeliğeuygunolaraküretilmiştir.
This product complies with Directive, Number 26891 regarding
“REGULATION ONTHE RESTRICTION OFTHE USE OF
CERTAIN HAZARDOUS SUBSTANCES IN ELECTRICAL AND
ELECTRONIC EQUIPMENT”.
PRECAUTIONS
Please observe the following precautions to prevent fire,
personal injury, and transceiver damage:
• Connectthetransceiveronlytoapowersourceasdescribed
in this manual or as marked on the transceiver itself.
• Routeallpowercablessafely.Ensurethepowercablescan
neither be stepped upon nor pinched by items placed near or
against the cables.Pay particular attention to locations near
AC receptacles, AC outlet strips, and points of entry to the
transceiver.
• Takecarenottodropobjectsorspillliquidintothe
transceiver through enclosure openings.Metal objects, such
as hairpins or needles, inserted into the transceiver may
contact voltages resulting in serious electrical shocks.Never
permit children to insert any objects into the transceiver.
• Donotattempttodefeatmethodsusedforgroundingand
electrical polarization in the transceiver, particularly involving
the power input cable.
• Adequatelygroundalloutdoorantennasforthistransceiver
using approved methods.Grounding helps protect against
voltage surges caused by lightning.It also reduces the
chance of a build-up of static charge.
EXAMPLE OF ANTENNA GROUNDING
ANTENNA
LEAD IN
WIRE
GROUND
CLAMP
ELECTRIC SERVICE
EQUIPMENT
ANTENNA
DISCHARGE UNIT
GROUNDING
CONDUCTORS
GROUND CLAMPS
POWER SERVICE
GROUNDING ELECTRODE
SYSTEM
• Minimumrecommendeddistanceforanoutdoorantenna
from power lines is one and one-half times the vertical height
of the associated antenna support structure.This distance
allows adequate clearance from the power lines if the support
structure fails for any reason.
• Locatethetransceiversoasnottointerferewithits
ventilation.Do not place books or other equipment on the
transceiver that may impede the free movement of air.Allow
a minimum of 10 cm (4 inches) between the rear of the
transceiver and the wall or operating desk shelf.
• Donotusethetransceivernearwaterorsourcesofmoisture.
For example, avoid use near a bathtub, sink, swimming pool,
or in a damp basement or attic.
• Thepresenceofanunusualodororsmokeisoftenasign
of trouble.Immediately turn the power OFF and remove the
power cable.Contact a KENWOOD service station or your
dealer for advice.
• Locatethetransceiverawayfromheatsourcessuchas
a radiator, stove, amplifier or other devices that produce
substantial amounts of heat.
• Donotusevolatilesolventssuchasalcohol,paintthinner,
gasoline, or benzene to clean the cabinet of the transceiver.
Use only a clean cloth with warm water or a mild detergent.
• Disconnecttheinputpowercablefromthepowersource
when the transceiver is not used for long periods of time.
• Removethetransceiver’senclosureonlytocarryour
accessory installations described in this manual or accessory
manuals.Follow the provided instructions carefully, to
avoid electrical shocks.If unfamiliar with this type of work,
seek assistance from an experienced individual, or have a
professional technician do the task.
• Enlisttheservicesofqualifiedpersonnelinthefollowing
cases:
a) The power supply or plug is damaged.
b) Objects have fallen into or liquid has spilled into the
transceiver.
c) The transceiver has been exposed to rain.
d) The transceiver is operating abnormally or performance
has seriously degraded.
e) The transceiver has been dropped or the enclosure
damaged.
• Donottouchthepowerplugwhileyourhandsarewetto
avoid risk of electric shock.
• Keepchildrenawayfromthetransceiver,toavoid
unnecessary risk of harm to the child.
• DonotremovetheplugfromanACoutletbypullingtheAC
cable.
• PlugtheACcableonlyintoagroundedACoutlet.
• Donotblockthetransceiverairvent.Donotcoverthe
transceiver.To maintain good ventilation, place the
transceiver at least 10 cm (4 inches) away from the wall.
PRIORTOYOUR FIRST QSO
III
IndexContents
TRANSPORTATION, INSTALLATION AND
PACKING MATERIAL STORAGE
This transceiver is precise and sensitive, and is heavy.
Take care not to hurt yourself and damage the transceiver
by dropping it.
To protect the transceiver from damage, the transceiver
must be transported and installed by two or more persons
securely holding the transceiver.
Store all packing materials for the transceiver for future
use, such as when transporting the transceiver when
moving or requesting after-sales service.To prevent it
from being damaged during transportation, wrap the
transceiver with the white protective cover in the same way
as it wrapped the transceiver at the time of purchase, then
the transceiver must be packed with its original packing
materials and transported with the front panel facing up as
illustrated above.Do not transport the transceiver placed
sideways.
ABOUTTHIS MANUAL
This manual was written subject to the specifications and
designs described below.
SpecificationsaredescribedinPRODUCT SPECIFICATIONS
in chapter 19, "MISCELLANEOUS".{page 19-2}
FirmwareVersion:1.02 (and later)
You can verify the firmware version as described below.
1 Press the main power switch (I/O) located on the rear
panel, to the "I" (ON) position to apply power to the
transceiver.
While the transceiver power ( ) is turned OFF, the " " LED
lights orange.While the transceiver power ( ) is turned ON,
the " " LED lights green.
[M.IN]
[]
2 Hold down [M.IN] (Memory), then press [ ].
After startup, the Firmware Update screen appears, and the
firmware version can be viewed.
3 Press [ ] to turn the transceiver power ( ) OFF.
Note:
◆There are two [M.IN] keys on this transceiver;one is for Memory
and the other for Quick Memory.To view the firmware version,
ensure to use [M.IN] (Memory).
◆Refer to Chapter 4 "Basic Operations" for the details of the power
sourcing.{page 4-1}
The latest firmware and its corresponding instruction
manual, in PDF format, can be downloaded from the
following URL:
http://www.kenwood.com/i/products/info/amateur/software_download.html
COPYRIGHTS FORTHIS MANUAL
JVC KENWOOD Corporation shall own all copyrights
and other intellectual properties for the product and the
software and for all manuals and documents attached to
the product and the software.
A user is required to obtain approval from JVC KENWOOD
corporation, in writing, prior to redistributing this document
on a personal web page or via packet communication.
A user is prohibited from assigning, renting, leasing or
reselling the document.
JVC KENWOOD Corporation does not warrant that quality
and functions described in this manual comply with each
user's purpose of use and, unless specifically described
in this manual, JVC KENWOOD Corporation shall be free
from any responsibility for any defects and indemnities for
any damages or losses.
PRIORTOYOUR FIRST QSO
IV Index Contents
SOFTWARE COPYRIGHTS
The title to and ownership of copyrights for software,
including but not limited to the firmware that may be
distributed individually, to be embedded in KENWOOD
product memories, are reserved for JVC KENWOOD
Corporation.
Any modifying, reverse engineering, copying, reproducing
or disclosing on an Internet website of the software is
strictly prohibited.
AuserisrequiredtoobtainapprovalfromJVCKENWOOD
corporation, in writing, prior to redistributing this manual
on a personal web page or via packet communication.
Furthermore, any reselling, assigning or transferring of the
software is also strictly prohibited without embedding the
software in KENWOOD product memories.
SOFTWARE LICENSE AGREEMENT
Software License Agreement contains the terms and
conditions of use of the software embedded in or used
with the transceiver.A user is entitled to use the software
subject to the acceptance and agreement of this Software
License Agreement by the user.Also, this Software
License Agreement stipulates the terms and conditions
of use of this software embedded in or used with the
transceiver, and a user has the right to use the transceiver
with the software embedded subject to the applicable laws
and regulations, the description and defined in this manual
and the warranty card.
The following procedures allow you to display the
Software License Agreement on the main screen.
Refer to Menu for the details of configuration method in
the Menu screen.{page 3-1}
[F1]~[F7]
F[ADV.] [MENU]
[MULTI/CH]
1 Press [ADV.] (F) from the Menu screen to open the
Advanced Menu screen.
2 Select Menu 28, "Software License Agreement", from
the Advanced Menu screen.
3 Press [SELECT] (F4) to display the Software License
Agreement.
4 Press [ ] (F2) or [ ] (F3), or rotate the
MULTI/CH control to scroll through the Software
License Agreement.
5 Press [MENU] to end.
IMPORTANT NOTICES CONCERNING THE
SOFTWARE
The software embedded in this transceiver consists of a
multiple number of and individual software components.
Title to and ownership of copyrights for each software
component is reserved for JVC KENWOOD Corporation
and the respective bona fide holder.
This product employs the software component in accordance
with the End User License Agreement (hereinafter referred
to as the "EULA") stipulated by JVC KENWOOD Corporation
and/or the respective bona fide holder.
There is free software stipulated and governed by the
“EULA”, and this, a distribution condition of the software
component in the executable format under the terms and
conditions contained in the GNU General Public License
or Lesser General Public License (hereinafter referred to
as the“GPL/LGPL”), requires to make the source code for
the relevant software components available.
Access the URL below for details of the software
component stipulated in the "GPL/LPGL".
http://www2.jvckenwood.com/gpl/index.html
The following procedures allow you to display Important
Notices concerning Free Open Source Software on the
main screen.
1 Press [ADV.] (F) from the Menu screen to open the
Advanced Menu screen.
2 Select Menu 29, "Important Notices concerning Free
Open Source", from the Advanced Menu screen.
3 Press [SELECT] (F4) to display the Important Notices
concerning Free Open Source.
4 Press [ ] (F2) or [ ] (F3), or rotate the
MULTI/CH control to scroll through the texts about
Important Notices concerning Free Open Source
Software.
5 Press [MENU] to end.
ABOUTTHE GPL/LPGL LICENSE
The following procedures allow you to display About the
GPL/LPGL License on the main screen.
1 Press [ADV.] (F) from the Menu screen to open the
Advanced Menu screen.
2 Select Menu 30, "AboutVarious Software License
Agreements", from the Advanced Menu screen.
3 Press [SELECT] to display AboutVarious Software
License Agreements.
4 Press [ ] (F2) or [ ] (F3), or rotate the
MULTI/CH control to scroll through the texts about
About the GPL/LPGL License.
5 Press [MENU] to end.
COPYRIGHTS FOR RECORDED AUDIO
The broadcast content recorded in this transceiver may
not be reused, except for the personal use, without prior
consent of the right holder under the copyright laws.
PRIORTOYOUR FIRST QSO
V
IndexContents
TRADEMARKS
• KENWOOD is a registered trade mark of JVC KENWOOD
Corporation.
• All other product names referenced herein are trademarks or
registered trademarks of their respective manufacturers.Marks such
as ™ and ® are omitted in the text of body.
INDEMNITY
• JVC KENWOOD Corporation takes all appropriate measures
to ensure all descriptions in this manual are accurate;however,
this manual may still contain typographical errors (“typos”) and
expressions that are misleading.JVC KENWOOD Corporation is
entirely free from any responsibilities arising from any losses or
damages caused by such typos or expressions.
• JVC KENWOOD Corporation has the right to change or improve
the product specifications, etc., described in this manual without
prior notice.JVC KENWOOD Corporation is entirely free from any
responsibilities for any losses or damages caused by such changes
and improvements.
• JVC KENWOOD Corporation is entirely free from any
responsibilities for any failures, damages or losses arising from, or
in connection with, use of the transceiver with or connected to any
external equipment.Failures, damages or losses shall include the
failures, damages or losses that may occur at the PC connected to
the transceiver or in storage devices having memory area such as
a USB flash drive.JVC KENWOOD Corporation is entirely free from
any responsibilities for any secondary failures, damages or losses,
including but not limited to the loss or damage of data or data files
stored in these memories.
• JVC KENWOOD Corporation does not warrant that the quality and
functions described in this manual comply with your purpose of use
and, unless specifically described in this manual, JVC KENWOOD
Corporation shall be free from any responsibilities for any defects
and indemnities for any damages or losses.Selection and installation
of any external equipment shall be done at your own risk.You are fully
responsible for the use and effects of external equipment.
• JVC KENWOOD Corporation shall be free from any responsibilities
for any incidental losses or damages, such as missing
communications or call opportunities caused by a failure or
performance error of the transceiver.
YOUR QUERIES ABOUT EXTERNAL DEVICES
OR PC CONNECTEDTOTHETRANSCEIVER
JVC KENWOOD Corporation are pleased to answer,
within the scope of corporate efforts we can provide,
your queries about your operation of this transceiver.
Please bear in mind that we cannot answer any and all
technical questions regarding methods of connection to,
configuration for and operation of any external device and
PC beyond our knowledge.
OPERATION OFTHE OPTIONAL APPLICATIONS
This manual is dedicated to describe the operation of
this transceiver.Refer to the help texts supplied with the
ARCP-990 and ARHP-990 for details of operation of the
ARCP-990 and ARHP-990 software installed onto your
PC.
TREATMENT OFYOUR IMPORTANT DATA
There is always a risk of Losing your important data
by a transceiver failure, occurrence of an unforeseen
contingency, erroneous operation or faulty behavior of the
transceiver.The data, such as the operating information,
recorded audio, messages, configuration data, logs, etc.,
must be backed up as necessary by yourself and stored in
the external storage device such as a USB flash drive.
TROUBLESHOOTING
If you aware of a failure, read through chapter 18,
"TROUBLESHOOTING".{page 18-7}
Maintenance methods, troubleshooting, and a list of error
messages are described.
Prior to transporting the transceiver for after-sales
servicing, contact KENWOOD service center for
transportation.
ABOUTTHE URL AND CONTACTS OF
JVC KENWOOD CORPORATION
The latest URL and contacts of JVC KENWOOD
Corporation at the time when this manual was written
are described in this manual.Due to changes of social
circumstances or the management environment, the URL
and contacts of JVC KENWOOD Corporation may change
from time to time.If you are unable to access the URL or
contacts, contact your dealer to determine the latest URL
and contacts.
NOTATIONS APPLIED TO THIS MANUAL
This transceiver has many user operations, such as those
for the main band and the sub band, keys and controls,
function keys and operations with connected equipment,
etc., as well as unique transceiver functionality.To clarify
and simplify the descriptions provided in this manual, the
following notations and writing conventions have been
used.
The captioned display images may differ from what
appears on your transceiver, due to your operating
environment, design changes, etc.
■ MAINBANDANDSUBBAND
Following a key or control name, (M) or (S) is shown, allowing
you to distinguish on which band, either the main band or the
sub band, the key or control is to be used.If the band that
the key or control is to be used for is not specified as either
the main band or the sub band, the band is specified as "the
selected band" in this manual.
■ KEYSANDCONTROLS
The transceiver has many keys and controls.The notation
"key" is omitted from individual keys;however, the notation
"control" is not omitted, allowing you to distinguish controls
from keys.
■ LEDANDDISPLAYS
On the transceiver front panel, there are LEDs that indicate
the status of the corresponding function as either active
or inactive.Information that appears on the main screen
or the sub screen is described as the "display".Refer to
chapter 2, "PANEL DESCRIPTION", for further details.
{page 2-1}
PRIORTOYOUR FIRST QSO
VI Index Contents
■ SCREENANDMESSAGES
Information that appears on the main screen after pressing
the MENU key or by a long press of any particular key is
described as the "screen".A text string (mainly in a message
box) navigating your operation or notifying you of an error is
described as a "message".
■ AUDIBLEOPERATIONAIDS
This transceiver assists your operation with a beep upon
a key press and the use of voice guidance.Configuration
methods for those audible operation aids are described in
this manual.
■FRONTPANELILLUSTRATIONONLYFOR[MENU]
AND [X.X.X] (F1)TO [X.X.X] (F7)
In this manual, due to availability of space, the front panel
illustration which indicates locations only of [MENU]
and [X.X.X] (F1) to [X.X.X] (F7) is exempted.When you
read this manual for the first time, you must note the
locations of the [MENU] and [X.X.X] (F1) to [X.X.X] (F7)
keys. {page 2-7} {page 2-12}
[F1]~[F7]
[MENU]
■IDENTICALKEYOPERATIONONTHEFRONT
PANEL
There are several methods of key operations to select a
parameter while the parameter box in the menu screen,
sub-menu screen, or configuration screen allows your entry
of the parameter.This manual describes operation methods
using the function keys;however, the operations below are
identical.
• Press [ ] (F2) or [ ] (F3).
• Press [-] (F4) or [+] (F5).
• Press [UP] or [DOWN].
• Rotate the MULTI/CH control.
[ESC] [F1]~[F7]
F[RESET]
F[CLOCK] F[LAN]
F[USBDRIVE]
F[ADV.] [MENU]
[UP]
[＜MAIN] [SUB＞]
[DOWN]
[MULTI/CH]
■ NOTATIONFORKEYS,CONTROLSANDDISPLAYS
In this manual, each key, control, and display are described.
Notation Example Overview
[x.x.x] [CW/CW-R]
[M>S] (M) Keys located on the front panel
The X.X.X
control
The MULTI/CH
control
The NB 1 (M)
control
Controls located on the front panel
The Tuning
control
The Tuning (M)
control
TheTuning (S)
control
The Tuning controls located on the
front panel
The "x.x.x"
LED
The "MAIN BUSY/
TX" LED
The "MONI/SEL"
LED
LEDs located on the front panel or on
the keys with the front panel
The X.X.X
connector The ACC 2
connector Connectors, jacks and ports located on
the front and rear panels
The x.x.x
screen
The Menu screen
The Bandscope
screen
Screens that appear on the main
screen to configure or select a
parameter.
"x.x.x" "FSK"
"Off"
What appears on the main screen
and the sub-screen, or a selected
parameter from the parameter box.
[X.X.X] (F) [ATT -12dB] (F)
Function keys corresponding to the key
guide along the right side of the main
screen.
The task name displayed on a key
guide appears in brackets.This task
name (key guide) may vary from
screen to screen.
[X.X.X] (F1
to F7) [(RESET)]
[MODE] (F7)
Function keys corresponding to the
key guide along the bottom of the main
screen.
The task name displayed on a key
guide appears in brackets.This task
name (key guide) may vary from
screen to screen.
PRIORTOYOUR FIRST QSO
VII
IndexContents
■ NOTATIONSFORUSEROPERATION
In this manual, various user operations are described, as
below.
Notation Example Overview
Press down
the main
power
switch (I/O)
Press the main power switch (I/O)
located on the rear panel, to the "I"
(ON) or "O" (OFF) position.
Press [ ]. Press [ ] on the front panel.
Press Press [MENU]. The MENU screen appears.If the
MENU screen is open, the MENU
screen closes.
Press Press [VOX]. Press momentarily to activate the
unique function of the key.
Press Press [ESC].
Press to revert to the screen which was
displayed prior to the current screen,
or to close the screen assigned for the
particular task.
Press and
hold
Press and hold
[CW/CW-R].
Press and hold
[(RESET)]
Press and hold a key for the time
configured in Menu 0-12, "Long Press
Duration of Panel Keys", to activate
the unique function of the key or the
function assigned to the key.
Hold down Hold down the
[PTT] switch.
Hold down a key to activate or enable
the specific function or behavior, until
the key is released.
TABLE OF CONTENTS
VIII Index
PRIORTOYOUR FIRST QSO
FEATURES..............................................................................................I
SUPPLIED ACCESSORIES....................................................................I
MARKET CODES ...................................................................................I
NOTICE TO THE USER ..........................................................................I
NOTIFICATION............................................................................I
PRECAUTIONS......................................................................................II
TRANSPORTATION, INSTALLATION AND PACKING MATERIAL
STORAGE.............................................................................................III
ABOUTTHIS MANUAL ........................................................................III
COPYRIGHTS FOR THIS MANUAL.....................................................III
SOFTWARE COPYRIGHTS..................................................................IV
SOFTWARE LICENSE AGREEMENT..................................................IV
IMPORTANT NOTICES CONCERNINGTHE SOFTWARE..................IV
ABOUTTHE GPL/LPGL LICENSE ......................................................IV
COPYRIGHTS FOR RECORDED AUDIO.............................................IV
TRADEMARKS......................................................................................V
INDEMNITY............................................................................................V
YOUR QUERIES ABOUT EXTERNAL DEVICES OR PC CONNECTED
TO THETRANSCEIVER........................................................................V
OPERATION OFTHE OPTIONAL APPLICATIONS..............................V
TREATMENT OFYOUR IMPORTANT DATA.........................................V
TROUBLESHOOTING...........................................................................V
ABOUTTHE URL AND CONTACTS OF JVC KENWOOD
CORPORATION.....................................................................................V
NOTATIONS APPLIEDTOTHIS MANUAL............................................V
1 INSTALLING AND CONNECTINGTHE
TRANSCEIVER
PRECAUTIONS FOR INSTALLATION................................................1-1
ANTENNA INSTALLATION AND CONNECTION ..............................1-1
CONNECTING AN AC POWER CABLE..................................................1-1
GROUND CONNECTION........................................................................1-1
LIGHTNING ARRESTER INSTALLATION..........................................1-1
TRANSCEIVERTILT MECHANISM....................................................1-1
TORQUEADJUSTMENTFORTUNING(M)CONTROL .......................1-2
ACCESSORIESCONNECTIONS(FRONTPANEL) ..........................1-2
HEADPHONES(PHONES).....................................................................1-2
MICROPHONE(MIC)..............................................................................1-3
PADDLE(PADDLE) .................................................................................1-3
USBFLASHDRIVE/USBKEYBOARD( ).........................................1-3
EXTERNALSPEAKERS(EXT.SP1/EXT.SP2,8Ω) ..................................1-3
KEYFORCW(KEY)................................................................................1-4
KEYPAD(KEYPAD) .................................................................................1-4
CONNECTIONTO AUDIO DEVICESWITH OPTICAL DIGITAL INPUT
TERMINAL ..............................................................................................1-4
CONNECTIONTOTHE EXTERNAL DISPLAY UNIT...............................1-4
METER....................................................................................................1-4
CONNECTIONTO A PC.....................................................................1-5
CONNECTIONTOANAPPLICABLETRANSCEIVER(QUICKDATA
TRANSFER)........................................................................................1-5
CONNECTIONTO THE LINEAR AMPLIFIER....................................1-6
CONNECTIONTOTHETL-922 ...............................................................1-6
CONNECTING ATYPICAL LINEAR AMPLIFIER ....................................1-6
CONNECTIONTO OTHER KENWOODTRANSCEIVERS WITH ATNC
TERMINAL..........................................................................................1-7
CONNECTIONTOANEXTERNALANTENNATUNERAT-300 ........1-8
CONNECTIONTO A TNC, MCP, ETC.................................................1-8
CONNECTINGTOYOUR LAN............................................................1-9
TERMINAL DESCRIPTIONS............................................................1-10
COM CONNECTOR ..............................................................................1-10
REMOTE CONNECTOR........................................................................1-10
ACC2 CONNECTOR.............................................................................1-11
EXT.AT CONNECTOR...........................................................................1-12
MIC CONNECTOR................................................................................1-12
2 PANEL DESCRIPTION
FRONT PANEL....................................................................................2-1
REAR PANEL......................................................................................2-9
MICROPHONE(OPTION) ................................................................2-11
MAIN SCREEN.................................................................................2-12
SUB-SCREEN...................................................................................2-15
3 MENU
MENU CONFIGURATIONS ................................................................3-1
OPENINGTHE MENU.............................................................................3-1
OPENINGTHE SUB MENU ....................................................................3-1
COMMON OPERATION INTHE MENU SCREEN ..................................3-1
CLOSINGTHE MENU.............................................................................3-1
SWITCHING THE OPERATING DATA BETWEEN CONFIG A AND
CONFIG B...............................................................................................3-2
MENU ITEMS..........................................................................................3-2
RESET MENU ITEMS .............................................................................3-9
CLOCK MENU ITEMS.............................................................................3-9
LAN MENU ITEMS..................................................................................3-9
ADVANCED MENU ITEMS....................................................................3-10
LIST OF USB MENU ITEMS..................................................................3-11
4 BASIC OPERATIONS
TURNINGTHE TRANSCEIVER ON...................................................4-1
TURNING THETRANSCEIVER OFF .................................................4-1
ENABLINGTHE STANDBY STATE LOW POWER CONSUMPTION.......4-2
CONTROLLINGTHE COOLING FANWHILE INTHE STANDBY STATE 4-2
COOLING FAN AND TEMPERATURE PROTECTION FOR FINAL UNIT4-3
MAIN AND SUB SCREEN DISPLAYS................................................4-3
MAIN SCREEN........................................................................................4-3
SUB SCREEN .........................................................................................4-4
CONFIGURINGTHE SCREEN TYPE.................................................4-5
CHANGINGTHE BACKGROUND COLOR.............................................4-5
CHANGINGTHE DISPLAY FONT...........................................................4-5
CHANGINGTHEDIALCOLOR(SUBSCREEN) ....................................4-6
CAPTURING AND SAVING SCREEN IMAGES.................................4-6
SELECTINGTHE DIMMER ................................................................4-6
CHANGING BRIGHTNESS.....................................................................4-6
ADJUSTINGTHE DIMMER LEVEL.........................................................4-6
SWAPPING THE OPERATING DATA BETWEEN MAIN BAND AND
SUB BAND..........................................................................................4-7
ADJUSTINGTHE AF GAIN................................................................4-7
MUTINGTHE RECEIVED AUDIO............................................................4-7
ADJUSTINGTHE RF GAIN................................................................4-8
ADJUSTINGTHE SQUELCH LEVEL.................................................4-8
CONFIGURINGTHE OPERATING BAND..........................................4-8
SELECTINGTHE OPERATING MODE ............................................4-10
LSB OR USB MODE .............................................................................4-10
CW/CW-RMODE ..................................................................................4-10
FSK/FSK-RORPSK/PSK-RMODE.......................................................4-10
FM/AM MODE.......................................................................................4-10
CONFIGURINGTHE DATA MODE........................................................4-10
AUTO MODE.....................................................................................4-11
ENABLING/DISABLING AUTO MODE..................................................4-11
CONFIGURING AUTO MODE FREQUENCY POINTS..........................4-11
TUNING THE FREQUENCY .............................................................4-12
TUNINGWITHTHETUNING CONTROL..............................................4-12
USINGTHE MICROPHONE KEYS........................................................4-13
CHANGINGTHE FREQUENCY ............................................................4-13
CHANGINGTHE STEP FREQUENCY..................................................4-13
ROUNDING OFFTHE FREQUENCY....................................................4-13
FINETUNING........................................................................................4-14
TUNING IN MHZ STEP .........................................................................4-14
SELECTINGTHE STEP FREQUENCY FOR AM BROADCAST LISTENING
..4-14
DIRECTLY ENTERINGTHE FREQUENCY ...........................................4-15
DISPLAYINGTHE HISTORY OF THE FREQUENCY ENTRIES ............4-15
USINGTHE FREQUENCY LOCK.....................................................4-16
TRANSMITTING...............................................................................4-17
AUDIOTRANSMISSION.......................................................................4-17
CWTRANSMISSION.............................................................................4-17
ADJUSTINGTHE MICROPHONE GAIN..........................................4-17
ADJUSTINGTHETX POWER..........................................................4-17
PRECISELY ADJUSTINGTHETX POWER...........................................4-17
TRANSMIT POWER LIMITER...............................................................4-18
METER..............................................................................................4-18
CHANGINGTHE METERTYPE............................................................4-18
CHANGINGTHETRANSMIT METER...................................................4-19
METERPEAK-VALUEHOLD ................................................................4-19
ANALOG METER RESPONSE SPEED.................................................4-19
STORING THE ANTENNA NAME....................................................4-20
CHANGINGTHE ANTENNA ............................................................4-20
TABLE OF CONTENTS
IX
Index
RX ANTENNA...................................................................................4-21
DRIVEOUTPUT(DRV).....................................................................4-21
INTERNAL ANTENNATUNER.........................................................4-21
SECURINGTHE MATCHINGTOTHE ANTENNA.................................4-21
PRESET................................................................................................4-22
CHANGINGTHE ANTENNA BEHAVIOR FOR RECEPTION................4-22
TRANSMIT HOLD AFTER ANTENNATUNING COMPLETES.............4-23
CONFIGURINGTHE STEREO HEADPHONES OUTPUT...............4-23
CONFIGURINGTHE MIX BALANCE OFTHE STEREO HEADPHONES
OUTPUT................................................................................................4-23
5 ASSISTINGYOUR SMOOTH QSO
SIMPLEX OPERATION.......................................................................5-1
SPLIT OPERATION ............................................................................5-1
FINDINGTHETXFREQUENCYBYROTATINGTHETUNINGCONTROL(S)
..5-1
DIRECTLY ENTERINGTHE FREQUENCY SPLIT SPECIFIED BY A DXER.
5-1
ROTATETHE TUNING(M)CONTROLTOSEARCHFORTHETRANSMIT
FREQUENCY...........................................................................................5-2
SEARCHINGWITHTF-SETENABLEDFORTHETRANSMIT
FREQUENCY DURING RECEPTION.................................................5-2
SIMULTANEOUS MAIN BAND AND SUB BAND RECEPTION.........5-3
FREQUENCY TRACKING...................................................................5-3
AGC(AUTOMATICGAINCONTROL) ...............................................5-4
SELECTINGTHE AGCTIME CONSTANT...............................................5-4
CHANGINGTHE AGCTIME CONSTANT...............................................5-4
COPYINGTHE AGC TIME CONSTANT CONFIGURATIONS .................5-5
DISABLINGTHE AGC.............................................................................5-5
RX DSP EQUALIZER..........................................................................5-6
SWITCHING THE RX DSP EQUALIZER ON OR OFF .......................5-6
SELECTINGTHE EQUALIZER CHARACTERISTICS .............................5-6
CUSTOMIZING THE EQUALIZER...........................................................5-6
COPYING CUSTOMIZED EQUALIZER DATA .........................................5-7
WRITING RX DSP EQUALIZER DATATO A USB FLASH DRIVE ...........5-8
READING RX DSP EQUALIZER DATA FROM A USB FLASH DRIVE.....5-8
PREAMP.............................................................................................5-9
RX MONITOR......................................................................................5-9
EMERGENCYCALL(K-TYPEONLY)...............................................5-10
SWL MODE.......................................................................................5-10
SWITCHING THE BANDWHILE IN SWL MODE...................................5-11
AUDIO SOURCE LINES FORTX AUDIO.........................................5-11
DATA MODE CONFIGURATION.......................................................5-12
TRANSMISSION BYTHE PTT SWITCH, SS PIN AND SEND...............5-12
TRANSMISSIONWITH DATA PTT OR DATA SEND .............................5-12
RIT/XITFUNCTIONS(FINE-TUNINGFUNCTIONSFORTRANSMIT
ANDRECEIVEFREQUENCIES)......................................................5-13
RIT(FINE-TUNINGOFRECEIVEFREQUENCIES) ..............................5-13
XIT(FINE-TUNINGOFTRANSMITFREQUENCIES)............................5-13
CONFIGURINGTHE CARRIER LEVEL...........................................5-13
ADJUSTINGTHE MICROPHONE GAIN..........................................5-14
OPERATION IN CW MODE..............................................................5-14
CWBREAK-IN ..................................................................................5-15
FULLBREAK-IN ....................................................................................5-15
SEMIBREAK-IN ....................................................................................5-15
ADJUSTINGTHE SIDETONE AND PITCH FREQUENCY...............5-16
ADJUSTINGTHE SIDETONEVOLUME................................................5-16
CW RISETIME..................................................................................5-16
AUTOZERO-IN(CWAUTOTUNE)..................................................5-17
CARRIER FREQUENCY OFFSET WHEN CHANGING FROM SSB
MODETO CW MODE .......................................................................5-17
AUTOMATICALLY CHANGING MODE FROM SSB FOR CW
TRANSMISSION...............................................................................5-18
ELECTRONIC KEYER......................................................................5-18
SELECTINGTHE KEYER TYPE FOR THE PADDLE JACK...................5-18
SELECTINGTHE KEYER TYPE FOR THE KEY JACK..........................5-19
MICROPHONE PADDLE MODE ...........................................................5-19
ADJUSTINGTHE KEYING SPEED .......................................................5-19
CHANGINGTHEWEIGHTING..............................................................5-20
WEIGHT REVERSE ..............................................................................5-20
REVERSINGTHE DOT AND DASH KEYING........................................5-21
OPERATING MODES OF ELECTRONIC KEYER .................................5-21
CW MESSAGE MEMORY.................................................................5-22
CHANGINGTHE ENTRY METHOD OF CW MESSAGES.....................5-22
STORING CW MESSAGESWITH TEXT ENTRY ..................................5-22
MANIPULATINGTHE PADDLE TO STORE CW MESSAGES ...............5-23
NAMINGTHECWMESSAGES(WITHPADDLEKEYINGONLY).........5-24
SELECTINGTHE CHANNEL NUMBER TO SAVE THE CONTEST
NUMBERFORMAT(TEXTENTRYONLY)............................................5-24
SELECTINGTHECONTESTNUMBERFORMAT(TEXTENTRYONLY)
..5-25
CONFIGURINGTHEFIRSTCONTESTNUMBER(TEXTENTRYONLY)
.5-25
DECREMENTINGTHECONTESTNUMBER(TEXTENTRYONLY)....5-26
PLAYING AND TRANSMITTING A CW MESSAGE.........................5-27
INTERRUPTINGTHE KEYING..............................................................5-27
DELETING CW MESSAGES.................................................................5-28
ADJUSTINGTHE MICROPHONE GAIN FOR FM MODE OPERATION
....5-28
FM NARROW OPERATION..............................................................5-29
REDUCINGTHEDEFLECTIONSOFTHES-METERFORUSEINFM-
MODE................................................................................................5-29
FM REPEATER OPERATION ...........................................................5-30
CONFIGURINGTHETONE FREQUENCY............................................5-30
SELECTINGTHETONE........................................................................5-31
USINGTHE SCANTO SEARCH FOR THETONE FREQUENCY .........5-31
CTCSSOPERATION(FMMODE)....................................................5-32
CONFIGURINGTHE CTCSS TONE FREQUENCY...............................5-33
SELECTINGTHE CTCSS TONE...........................................................5-33
USINGTHE SCANTO SEARCH FOR THE CTCSSTONE FREQUENCY
.....5-34
SELECTINGTHE CROSSTONE ..........................................................5-34
RTTY OPERATION ...........................................................................5-35
OPENINGTHE RTTY ENCODE/DECODE SCREEN............................5-35
OPERATIONS ONTHE RTTY ENCODE/DECODE SCREEN...............5-35
SELECTINGMAINBANDANDSUBBANDFORRECEPTION(FSK)
5-36
SAVINGTHE CONTENTS OF RTTY COMMUNICATION................5-36
SELECTINGTHE FILE FORMAT ATTHETIME OF SAVING DATA.......5-37
ADJUSTINGTHE RTTYTHRESHOLD LEVEL OF RTTY DECODING
5-37
DISPLAYING THE SCOPETO CHECK RTTYTUNING...................5-38
FFT SCOPE...........................................................................................5-38
AVERAGINGTHE WAVEFORM INTHE FFT SCOPE............................5-38
WATERFALL..........................................................................................5-38
X-YSCOPE(SUB-SCREEN).................................................................5-38
USINGTHE USB KEYBOARDTOTRANSMIT A TEXT STRING....5-39
TRANSMITTINGTHE ENTEREDTEXT STRING AS ENTERED ..........5-39
STORING TEMPORARILY AND TRANSMITTINGTHE TEXT STRING IN
THE BUFFER........................................................................................5-39
UTILIZING AN RTTY MESSAGE MEMORY.....................................5-40
STORING MESSAGES..........................................................................5-40
CONFIGURINGTHE AUTOMATIC TRANSMISSION AND RECEPTION
FORTHE RTTY MESSAGE MEMORY.............................................5-41
CONFIGURINGTHE AUTOMATIC TRANSMISSION AND RECEPTION
USINGTHE RTTY MESSAGE MEMORY.........................................5-42
CONFIGURATION FOR RTTY ENCODING AND DECODING........5-42
ENABLINGTHEUOS(UNSHIFTONSPACE) ......................................5-42
CONFIGURINGTHE NEWLINE CODE.................................................5-43
DIDDLE OPERATION............................................................................5-43
ENABLINGTHE ENCODE UOS............................................................5-44
SENDINGTHE NEWLINE CODE AT THE START AND END OF
TRANSMISSION...................................................................................5-44
DISPLAYINGTHETIME STAMP............................................................5-45
SELECTINGTHETIMESTAMPTIME....................................................5-45
RTTY PARAMETERS........................................................................5-46
CONFIGURINGTHE MARK FREQUENCY...........................................5-46
CONFIGURINGTHE RTTY SHIFT WIDTH............................................5-46
REVERSINGTHE FREQUENCY IN RTTY MODE............................5-47
CONFIGURINGTHE POLARITY FOR ACC 2 KEYING...................5-47
USING AN EXTERNAL DEVICE FOR RTTY MODE OPERATION..5-47
AUDIO PEAK FILTER.......................................................................5-48
PSK OPERATION .............................................................................5-48
OPENINGTHE PSK ENCODE/DECODE SCREEN.........................5-48
SELECTINGMAINBANDANDSUBBANDFORRECEPTION(PSK)
5-49
SAVINGTHE CONTENTS OF PSK COMMUNICATION..................5-50
SELECTSTHE FILE FORMAT AT THETIME OF SAVING DATA...........5-51
ADJUSTINGTHE RTTYTHRESHOLD LEVEL OF PSK DECODING
..5-51
DISPLAYING THE SCOPETO CHECK PSKTUNING.....................5-52
FFT SCOPE...........................................................................................5-52
AVERAGINGTHE WAVEFORM INTHE FFT SCOPE............................5-52
WATERFALL..........................................................................................5-52
VECTORSCOPE(SUB-SCREEN)........................................................5-52
AFC(AUTOMATICFREQUENCYCONTROL).................................5-53
CONFIGURINGTHE AFC TUNING RANGE....................................5-54
NET...................................................................................................5-54
SELECTING BPSK OR QPSK..........................................................5-55
SELECTINGPSK31ORPSK63.......................................................5-55
TABLE OF CONTENTS
XIndex
USINGTHE USB KEYBOARDTOTRANSMIT A TEXT STRING....5-56
TRANSMITTINGTHE ENTEREDTEXT STRING AS ENTERED ..........5-56
TEMPORARILY STORING AND TRANSMITTINGTHE TEXT STRING IN
THE BUFFER........................................................................................5-56
UTILIZING AN PSK MESSAGE MEMORY.......................................5-57
STORING MESSAGES..........................................................................5-57
CONFIGURING AUTOMATIC TRANSMISSION AND RECEPTION FOR
THE PSK MESSAGE MEMORY............................................................5-58
SENDING ATEXT STRING STORED IN PSK MESSAGE MEMORY....5-59
CONFIGURATION FOR PSK ENCODING AND DECODING..........5-59
DISPLAYINGTHETIME STAMP............................................................5-59
SELECTINGTHETIMESTAMPTIME....................................................5-60
PSK-RELATEDCONFIGURATION...................................................5-60
CONFIGURINGTHE PSKTONE FREQUENCY....................................5-60
REVERSINGTHE PHASE CHANGE DIRECTION IN QPSK.................5-60
USING A PCTO COMMUNICATE IN PSK MODE.................................5-60
6 REJECTINGINTERFERENCE
ATTENUATOR(ATT)...........................................................................6-1
PRESELECTOR..................................................................................6-1
DSP FILTER........................................................................................6-2
CHANGINGTHE IF FILTER BANDWIDTH CHARACTERISTICS......6-2
SWITCHING THE RX FILTER CONFIGURATIONS ................................6-2
CONFIGURINGTHE NUMBER OF RX FILTERS SELECTABLE.............6-3
SELECTINGTHE ROOFING FILTER ......................................................6-3
SWITCHING THE IF FILTERTYPE..........................................................6-4
CONFIGURINGTHEBEHAVIOROFHI/SHIFTANDLO/WIDTH(SSBAND
SSB-DATAONLY)....................................................................................6-4
CHANGINGTHE AF FILTERTYPE....................................................6-5
CHANGINGTHECUTOFFFREQUENCIES(LOWAND
HIGHFREQUENCY)TOADJUSTTHEPASSBANDWIDTH
CHARACTERISTICS ..........................................................................6-6
CHANGINGTHE PASSBANDWIDTH AND SHIFTTO ADJUST
PASSBAND CHARACTERISTICS......................................................6-7
ACTIVATING AUDIO PEAK FILTER FOR USE IN CW MODE...........6-7
CHANGINGTHE PASSBAND CHARACTERISTICS OF THE AUDIO
PEAKFILTER(APF)...........................................................................6-8
SHIFTINGTHE PASSBAND OFTHE AUDIO PEAK FILTER.............6-8
AUDIO PEAK FILTERWHILE IN FSK MODE....................................6-9
NOISE BLANKER...............................................................................6-9
MANUALNOTCHFILTER(SSB,CW,FSK,ANDPSK)...................6-10
AUTONOTCHFILTER(SSB) ...........................................................6-11
BAND ELIMINATION FILTER...........................................................6-12
NOISE REDUCTION.........................................................................6-13
BEATCANCELLER(SSB,AMANDFM).........................................6-14
DSP MONITOR.................................................................................6-15
ASSIGNINGTHE DSP MONITOR TO THE PF KEY..............................6-15
EXPANDINGTHE PASSBANDWIDTH OF THE FILTER USINGTHE DSP
MONITOR..............................................................................................6-15
7 BANDSCOPE
BANDSCOPE......................................................................................7-1
DISPLAYINGTHE BANDSCOPE ............................................................7-1
WATERFALL............................................................................................7-1
ADJUSTINGTHE REFERENCE LEVEL..................................................7-1
CONFIGURINGTHEWATERFALL DISPLAY FALL SPEED ....................7-2
CHANGINGTHEDISPLAYOFTHEBANDSCOPE(MAINBANDAND
SUBBAND).............................................................................................7-2
DISPLAYINGTHE BANDSCOPE AND ANOTHER SCREEN..................7-2
TOGGLING THE CENTER MODE AND FIXED MODE...........................7-2
CHANGINGTHEDISPLAYEDFREQUENCYSPAN(CENTERMODE)..7-3
SWITCHINGTHEMARKEROFFSETFREQUENCY(SSBONLY)..........7-3
SELECTINGTHEFREQUENCYDISPLAYINTHEGRID(RELATIVE
FREQUENCYORABSOLUTEFREQUENCY)........................................7-4
CHANGINGTHE RECEIVE FREQUENCY USINGYOUR FINGERTIP
(CENTERMODE)....................................................................................7-4
CONFIGURINGTHE LOWER AND UPPER LIMIT .................................7-5
APPLYINGTHE LOWER LIMIT FREQUENCY OR UPPER LIMIT
FREQUENCY FOR CENTER MODETO FIXED MODE..........................7-5
CHANGINGTHE RECEIVE FREQUENCY USINGYOUR FINGERTIP
(FIXEDMODE)........................................................................................7-5
DISPLAYINGTHE MARKERS.................................................................7-6
OFF-RANGEMARKERSFORFREQUENCIESBEYONDTHELOWER
AND UPPER LIMITS................................................................................7-6
SHIFTINGTHE SCOPE AREA BY PLACINGTHE MARKER NEAR
CENTER(FIXEDMODE) ........................................................................7-6
DISPLAYINGTHE MAXIMUMWAVEFORMVALUE................................7-7
PAUSINGTHEWAVEFORM DISPLAY....................................................7-7
AVERAGINGTHE WAVEFORM DISPLAY ON THE BANDSCOPE..........7-7
CHANGINGTHE ATTENUATOR FOR THE BANDSCOPE................7-8
DISPLAYING THE TRANSMISSION SIGNAL WAVEFORM ..............7-8
8 AUDIOSCOPE
DISPLAYING THE AUDIO SCOPE AND OSCILLOSCOPE...............8-1
CHANGINGTHE AUDIO SOURCE FORTHE AUDIO SCOPE................8-1
CHANGINGTHE ATTENUATOR FORTHE AUDIO SCOPE ...................8-1
CHANGINGTHE AUDIO SCOPE FREQUENCY DISPLAY SPAN...........8-2
CHANGINGTHE LEVEL OFTHE OSCILLOSCOPE...............................8-2
CHANGINGTHE SWEEP TIME ..............................................................8-3
PAUSINGTHE AUDIO SCOPE AND OSCILLOSCOPE ..........................8-3
9 TRANSMITFUNCTIONS
SELECTINGTHE AUDIO LINE FORTRANSMISSION .....................9-1
SELECTINGTHE AUDIO SOURCE FORTRANSMISSION BY SEND/
PTT......................................................................................................9-1
SELECTINGTHE AUDIO SOURCETRANSMISSION BY SEND/PTT ....9-1
SELECTINGTHE AUDIO SOURCE FOR TRANSMISSION BY DATA SEND
....9-2
VOX(VOICE-OPERATEDTRANSMIT)...............................................9-2
SWITCHINGVOX(VOICE)ONOROFF..................................................9-2
SELECTING OR DISABLING THE AUDIO SOURCE FOR DATAVOX ....9-2
ADJUSTINGTHE VOX GAIN...................................................................9-3
ADJUSTINGTHE VOX DELAYTIME.......................................................9-3
ADJUSTINGTHE ANTI VOX GAIN LEVEL..............................................9-4
DELAYINGTHE AUDIO SIGNAL.............................................................9-5
TX MONITOR......................................................................................9-5
ADJUSTINGTHE TX MONITOR LEVEL..................................................9-5
SPEECH PROCESSOR......................................................................9-6
ADJUSTINGTHE SPEECH PROCESSOR OUTPUT LEVEL..................9-7
ADJUSTINGTHE EFFECT OFTHE SPEECH PROCESSOR.................9-7
TRANSMIT FILTER.............................................................................9-8
SELECTING ATX FILTER.......................................................................9-8
CHANGINGTHE NUMBER OF AVAILABLETX FILTERS.......................9-8
CHANGINGTHE BANDWIDTH OF THETX FILTER...............................9-9
TX DSP EQUALIZER..........................................................................9-9
SWITCHING THETX DSP EQUALIZER ON OR OFF .............................9-9
SELECTINGTHE FREQUENCY CHARACTERISTICS OFTHETX DSP
EQUALIZER ..........................................................................................9-10
ADJUSTINGTHE TX DSP EQUALIZER................................................9-10
COPYINGTHE CONFIGURATION DATA FORTHETX DSP EQUALIZER
9-11
SAVINGTHE CONFIGURATION DATA FOR THETX DSP EQUALIZER
....9-11
READINGTHE CONFIGURATION DATA FOR THETX DSP EQUALIZER
.9-12
DISPLAYING THE SUBSCOPE DURINGTX...................................9-13
TXTUNING.......................................................................................9-14
ADJUSTINGTHE TRANSMIT POWER FORTXTUNING.....................9-14
TIME-OUTTIMER(TOT) ..................................................................9-14
10MEMORYCHANNELS
MEMORY CHANNEL........................................................................10-1
DISPLAYINGTHE MEMORY CHANNEL LIST ......................................10-1
CONFIGURINGTHE OPERATING DATA TO A MEMORY CHANNEL ..10-2
CONFIGURINGTHEOPERATINGDATATOASINGLE-BANDMEMORY
CHANNEL.............................................................................................10-2
CONFIGURINGTHEOPERATINGDATATOADUAL-BANDMEMORY
CHANNEL.............................................................................................10-3
CONFIGURING OPERATING DATA BY DIRECTLY ENTERING A
FREQUENCY........................................................................................10-3
MEMORY CHANNEL MODE............................................................10-4
OPERATINGINSINGLE-BANDMEMORYCHANNELMODE..............10-4
OPERATINGINDUAL-BANDMEMORYCHANNELMODE .................10-4
SELECTING A MEMORY CHANNEL....................................................10-5
DIRECTLY ENTERINGTHE MEMORY CHANNEL NUMBER...............10-5
TEMPORARILY CHANGINGTHE OPERATING DATA ....................10-5
TEMPORARILY CHANGINGTHE FREQUENCY ..................................10-5
COPYING OPERATING DATA FROMTHE MEMORY CHANNEL...10-6
MEMORYSHIFT(MEMORYTOVFO)...................................................10-6
COPYING OPERATING DATA FROM ONE MEMORY CHANNELTO
ANOTHERMEMORYCHANNEL(CHANNELTOCHANNEL)..............10-6
CONFIGURINGTHE PROGRAM SCAN FREQUENCY RANGE.....10-7
TABLE OF CONTENTS
XI
Index
CLEARINGTHE MEMORY CHANNEL............................................10-7
CONFIGURING NAMES FOR MEMORY CHANNELS.....................10-7
QUICK MEMORY..............................................................................10-8
QUICK MEMORY CHANNELS.........................................................10-8
CONFIGURING IN QUICK MEMORY...............................................10-8
RECALLING QUICK MEMORY CHANNELS ...................................10-8
CONFIGURINGTHE NUMBER OF QUICK MEMORY CHANNELS10-9
CLEARING QUICK MEMORY CHANNELS .....................................10-9
MEMORYSHIFT(QUICKMEMORYTOVFO) ......................................10-9
11 SCAN
PROGRAM SCAN.............................................................................11-1
STARTINGTHEPROGRAMSCAN(VFOSCAN)..................................11-1
CONFIGURINGTHEPROGRAMSCAN(VFOSCAN)FREQUENCY
RANGE..................................................................................................11-1
CHANGINGTHE SCAN SPEED............................................................11-2
SCAN HOLD..........................................................................................11-2
PROGRAM SLOW SCAN......................................................................11-3
ENABLING OR DISABLINGTHE PROGRAM SLOW SCAN.................11-3
CONFIGURINGTHE PROGRAM SLOW SCAN FREQUENCY RANGE
.11-3
CONFIGURINGTHE PROGRAM SLOW SCAN FREQUENCY RANGE
.11-4
MEMORY SCAN................................................................................11-4
STARTINGTHE SCAN ..........................................................................11-4
EXAMPLES OF CONFIGURATIONS FORTHE ALL CHANNEL SCAN
ANDTHE GROUP SCAN ......................................................................11-4
LOCKING OUT A MEMORY CHANNEL................................................11-5
QUICK MEMORY SCAN...................................................................11-6
RESUMINGTHE SCANNING...........................................................11-6
12 ABOUTTHE USB FLASH DRIVE
ABOUTTHE USB FLASH DRIVE.....................................................12-1
FORMATTING A USB FLASH DRIVE..............................................12-1
SAFELY REMOVINGTHE USB FLASH DRIVE ...............................12-1
SAVING A FILE IN USB FLASH DRIVE...........................................12-2
READING A FILE FROM USB FLASH DRIVE.................................12-2
DELETING A FILE FROM USB FLASH DRIVE...............................12-3
CHANGING A FILE NAME INTHE USB FLASH DRIVE.................12-4
13VOICE MESSAGE AND AUDIO FILE
RECORDING AND PLAYING VOICE MESSAGE.............................13-1
RECORDING AVOICE MESSAGE .......................................................13-1
NAMING AVOICE MESSAGE...............................................................13-2
PLAYING AVOICE MESSAGE..............................................................13-2
ADJUSTINGTHE VOLUME OF VOICE MESSAGE...............................13-3
TRANSMITTING AVOICE MESSAGE ..................................................13-3
CLEARING AVOICE MESSAGE...........................................................13-4
CONFIGURING INTERVAL TIME FOR RETRANSMIT..........................13-4
RECORDING AND PLAYING COMMUNICATION AUDIO.....................13-4
CONFIGURINGTHE SAVE DESTINATION OF AUDIO FILE.................13-4
MANUAL RECORDING.........................................................................13-5
FULL-TIMERECORDING .................................................................13-5
CONFIGURINGTHEMAXIMUMTIMEFORFULL-TIMERECORDING 13-5
SAVINGAUDIOWITHFULL-TIMERECORDING..................................13-6
PLAYING AN AUDIO FILE................................................................13-6
ADJUSTINGTHE VOLUME OF VOICE MESSAGE...............................13-6
AUDIO FILES....................................................................................13-7
COPYING AUDIO FILE FROM INTERNAL MEMORYTO USB FLASH
DRIVE....................................................................................................13-7
PLAYING AN AUDIO FILE.....................................................................13-7
NAMING AN AUDIO FILE......................................................................13-8
DELETING AN AUDIO FILE ..................................................................13-9
PROTECTINGANAUDIOFILEFROMDELETION(ONLYFORINTERNAL
MEMORY) ..........................................................................................13-10
14VOICE GUIDANCE
VOICE GUIDANCE ...........................................................................14-1
CONFIGURINGTHEVOLUME OFTHEVOICE GUIDANCE.................14-1
CONFIGURINGTHEVOICE GUIDANCE SPEED.................................14-1
CONFIGURINGTHE ANNOUNCEMENT LANGUAGE.........................14-1
AUTOMATICALLY ANNOUNCINGVOICE GUIDANCE.........................14-2
VOICE 1.................................................................................................14-3
VOICE 2...............................................................................................14-10
VOICE 3...............................................................................................14-10
15 CLOCK DISPLAY ANDTIMER
CONFIGURING THE DATE AND TIME ............................................15-1
CONFIGURINGTHE DATE FORTHE LOCAL CLOCK.........................15-1
CONFIGURINGTHETIME FOR THE LOCAL CLOCK..........................15-1
CONFIGURINGTHETIMEZONE FORTHE LOCAL CLOCK................15-2
CONFIGURINGTHETIMEZONE FORTHE SECONDARY CLOCK .....15-2
CONFIGURING AN IDENTIFICATION LETTER FOR THE SECONDARY
CLOCK..................................................................................................15-2
CONFIGURINGTHE DATE DISPLAY FORMAT ....................................15-2
CORRECTINGTHECLOCKWITHNTP(NETWORKTIME
PROTOCOL) .....................................................................................15-3
CONFIGURINGTHE NTP SERVER ADDRESS....................................15-3
ENABLING OR DISABLINGTHE AUTOMATICTIME CORRECTION...15-4
MANUAL CLOCK CORRECTION .........................................................15-4
TIMER...............................................................................................15-4
CONFIGURINGTHE PROGRAMMABLETIMER..................................15-5
TEMPORARILY DISABLINGTHETIMER TASK....................................15-6
SLEEPTIMER...................................................................................15-6
CONFIGURINGTHE SLEEPTIMER.....................................................15-6
DISABLINGTHEPOWER-OFFBYTHESLEEPTIMER........................15-7
APO(AUTOMATICPOWEROFF)....................................................15-7
16USEFULFUNCTIONS
CONFIGURINGTHEPOWER-ONMESSAGE .................................16-1
CONFIGURINGTHE SCREEN SAVER............................................16-1
CONFIGURINGTHE SCREEN SAVER TYPE.......................................16-1
CONFIGURING THE SCREEN SAVER WAIT TIME.........................16-2
CONFIGURINGTHE TEXT STRING FORTHE SCREEN SAVER...16-2
TOUCHING THE SCREENTO SELECT A FREQUENCY................16-3
TOUCHING THE SCREEN....................................................................16-3
CALIBRATINGTHETOUCHSCREEN...................................................16-3
RESET...............................................................................................16-4
SELECTINGTHE OPERATING BAND FOR THE HI/SHIFT LO/
WIDTH CONTROLS..........................................................................16-4
CONFIGURINGTHE LENGTH OFTIME FOR KEY LONG PRESS.16-5
ADJUSTINGTHE BEEPVOLUME...................................................16-5
MIXINGTHE BEEPS, ETC.TO THE RECEIVED AUDIO OUTPUT
FROMTHE REAR PANEL................................................................16-6
PFKEYS(PROGRAMMABLEFUNCTIONKEYS) ..........................16-6
ASSIGNINGVARIOUS FUNCTIONSTO THE FRONT PANEL PF KEYS
...16-6
ASSIGNINGVARIOUS FUNCTIONSTO THE MICROPHONE PF KEYS
...16-7
ASSIGNINGVARIOUS FUNCTIONSTOTHE EXTERNAL PF KEYS....16-7
PC CONTROL.................................................................................16-10
SELECTINGTHEBAUDRATEOFTHECOM/USB(REARPANEL)PORT
..16-10
CONFIGURINGTHE USB KEYBOARD.........................................16-10
SELECTINGTHE LANGUAGE FORTHE USB KEYBOARD...............16-10
CONFIGURINGTHE KEY REPEAT DELAY TIME...............................16-11
CONFIGURINGTHE KEYING SPEED................................................16-11
ENABLING USING USB KEYBOARDTO SEND A MESSAGE ...........16-11
CAPTURING AND SAVING SCREEN IMAGES.............................16-12
CONFIGURING THE NETWORK ...................................................16-12
CONFIGURINGTHE IP NETWORK....................................................16-12
CHECKINGTHE MAC ADDRESS.......................................................16-13
CONFIGURINGTHE NETWORK ADMINISTRATOR..........................16-14
CONFIGURINGTHE OUTPUT TO AN EXTERNAL METER..........16-15
SELECTINGTHE OUTPUT SIGNAL TYPE OFTHE MAIN BAND FOR AN
EXTERNAL METER............................................................................16-15
SELECTINGTHE OUTPUT SIGNAL TYPE OFTHE SUB BAND FOR AN
EXTERNAL METER............................................................................16-16
SETTINGTHE OUTPUT LEVEL OF AN EXTERNAL METER.............16-16
SELECTINGTHE OUTPUT SIGNAL OF AN EXTERNAL SPEAKER
...16-17
DISPLAYING THE MAIN SCREEN CONTENTS ON AN EXTERNAL
MONITOR........................................................................................16-18
CONFIGURINGTHE RESOLUTION OF THE EXTERNAL MONITOR
...16-18
CONFIGURINGTHE I/O SIGNALS FOR THE OPTICAL DIGITAL
CONNECTOR..................................................................................16-19
CONFIGURINGTHE INPUT AUDIO LEVEL........................................16-19
CONFIGURINGTHE OUTPUT AUDIO LEVEL....................................16-19
SELECTINGTHE AUDIO OUTPUT FORMAT FROMTHE OPTICAL OUT
CONNECTOR......................................................................................16-19
CONFIGURINGTHE I/O SIGNALS FOR THE ACC 2 CONNECTOR
....16-20
CONFIGURINGTHE INPUT AUDIO LEVEL........................................16-20
CONFIGURINGTHE OUTPUT AUDIO LEVEL....................................16-20
SELECTINGTHE AUDIO OUTPUT FORMAT FROMTHE ACC 2 CONNECTOR
.16-20
TABLE OF CONTENTS
XII Index
CONFIGURINGTHE I/O SIGNALS FOR THE USB CONNECTOR
.16-21
CONFIGURINGTHE INPUT AUDIO LEVEL........................................16-21
CONFIGURINGTHE OUTPUT AUDIO LEVEL....................................16-21
SELECTINGTHE AUDIO OUTPUT FORMAT FROMTHE USB CONNECTOR
...16-21
CONFIGURINGTHE REF I/O CONNECTOR.................................16-22
CONFIGURINGAPERSONALROOFINGFILTER(MAINBAND
ONLY)..............................................................................................16-22
CONFIGURINGTHE PASSBANDWIDTH...........................................16-22
CONFIGURINGTHE ATTENUATION..................................................16-23
OPERATINGTHE TRANSCEIVER FOR AVOIP AMATEUR RADIO
STATION .........................................................................................16-23
CHANGINGTHE CTCSS MUTE .........................................................16-23
CONFIGURINGTHE SQL CONTROL SIGNAL.............................16-24
SELECTINGTHE MSQ/SSQ LOGIC...................................................16-24
CONFIGURINGTHE MSQ/SSQ OUTPUT CONDITIONS...................16-24
SWITCHING THE COM CONNECTOR PIN ARRANGEMENT............16-25
QUICK DATATRANSFER...............................................................16-26
TRANSFERRINGTHE OPERATING DATA TOTHE SLAVE
TRANSCEIVER...................................................................................16-26
RECEIVINGTHE OPERATING DATA FROMTHE MASTER
TRANSCEIVER...................................................................................16-26
INHIBITINGTRANSMISSION..............................................................16-27
DX PACKETCLUSTERTUNE.........................................................16-27
CONFIGURINGTHETRANSCEIVER.................................................16-27
RECEIVING DX PACKETCLUSTER DATA USINGTHE CONNECTED
TRANSCEIVER...................................................................................16-28
CONTROLLING EXTERNAL EQUIPMENT....................................16-28
INHIBITINGTHETRANSMISSIONDURINGBUSY(SQUELCH
OPENING)...........................................................................................16-28
REVERSINGTHE PKS SIGNAL POLARITY .......................................16-29
CROSSBAND REPEATER..............................................................16-29
PREPARATION....................................................................................16-29
OPERATION........................................................................................16-30
SKY COMMAND SYSTEM II...........................................................16-30
PREPARATION....................................................................................16-30
TS-990S+TH-D72A/E,TM-D710A/EORTM-D700A(G)
(TRANSPORTER)CONFIGURATION.................................................16-31
CONTROLLINGTHE LINEAR AMPLIFIER....................................16-31
CONTROLLINGTHE LINEAR AMPLIFIER FOR OPERATION INTHE HF
BAND ..................................................................................................16-31
CONTROLLINGTHE LINEAR AMPLIFIER AT 50 MH
z
.......................16-32
OPERATINGTHE TRANSCEIVER AS AN EXCITER OF THE
TRANSVERTER..............................................................................16-33
CONNECTINGTHETRANSVERTERTOTHETRANSCEIVER..........16-33
TRANSMIT POWER REDUCTION WHILETHE TRANSVERTER IS
ENABLED............................................................................................16-33
DISPLAYINGTHE OPERATION FREQUENCY ONTHE TRANSVERTER
....16-34
CONFIGURINGTHE FREQUENCY USING THETRANSVERTER.....16-34
17 FIRMWARE UPDATING
ABOUT FIRMWARE UPDATING......................................................17-1
UPDATINGTHE FIRMWARE............................................................17-1
VERIFYINGTHE FIRMWAREVERSION..........................................17-1
FIRMWARE UPDATING WITH A PC CONNECTED ........................17-2
PREPARATION......................................................................................17-2
YOUR OPERATION FOR THETRANSCEIVER ANDYOUR PC............17-2
FIRMWARE UPDATING USING A USB FLASH DRIVE ..................17-3
PREPARATION......................................................................................17-3
YOUR OPERATION FOR THETRANSCEIVER ANDYOUR PC............17-3
18TROUBLESHOOTING
CALIBRATING THE INTERNAL REFERENCE FREQUENCY.........18-1
CALIBRATION PROCEDURE ...............................................................18-1
RESETTING ALL CONFIGURATIONS.............................................18-2
REPLACINGTHE FUSE FOR AN EXTERNAL ANTENNATUNER 18-2
HOWTO REPLACE THE FUSE.............................................................18-2
NOTICE CONCERNING INTERNAL BEAT......................................18-3
INTERNAL BEAT OCCURRED INTHE MAIN BAND ...........................18-3
INTERNAL BEAT OCCURRED INTHE SUB BAND..............................18-3
OTHER COMBINATIONS......................................................................18-3
SPURIOUSSIGNALONTHEBANDSCOPE(WATERFALL) ..........18-3
THE LIST OF ERROR MESSAGES.......................................................18-4
THE LIST OFWARNING MESSAGES...................................................18-6
TROUBLESHOOTING......................................................................18-7
SYMPTOMS ENCOUNTERED DURING RECEPTION AND
TRANSMISSION...................................................................................18-7
SYMPTOMS ENCOUNTERED IN ASSOCIATION WITH DATA
COMMUNICATIONS, PC AND NETWORK.........................................18-11
SYMPTOMS ENCOUNTERED DURING RECORDING AND PLAYING
..18-13
19MISCELLANEOUS
PRIME OPTIONAL ACCESSORIES.................................................19-1
DEDICATED APPLICATIONS...........................................................19-1
PRODUCT SPECIFICATIONS..........................................................19-2
INDEX ...............................................................................................19-3
1-1
1INSTALLING AND CONNECTINGTHETRANSCEIVER
IndexContents
PRECAUTIONS FOR INSTALLATION
To carry and install the transceiver requires two or more
persons.Due to the size and weight of the equipment,
installing the transceiver by yourself may cause you
personal injury and/or damage the transceiver.
Do not grasp the transceiver by the Tuning control, the
knobs or connectors on the front and rear panels.Doing
so may cause you personal injury and/or damage the
transceiver knobs and connectors.
ANTENNA INSTALLATION AND CONNECTION
An antenna system consists of an antenna, a coaxial
cable and a ground.With careful installation, a good
antenna system can result in optimal performance for the
transceiver.
Ensure that you are using a correctly tuned 50Ω antenna
and that the coaxial cable and appropriate connectors
also have an impedance of 50Ω. All connections must be
clean and tight.
After making the connection, match the impedance of the
coaxial cable and antenna until the SWR becomes 1.5:1
or less.
A high SWR results in a drop in the transmit power as well
as radio frequency interference to consumer products
such as broadcast radio and television.
If you are notified that the signal has been distorted,
the antenna system may not be efficiently radiating the
transceiver's power.
PRECAUTIONS
◆Transmission without connecting an antenna to the transceiver may
damage the transceiver.Prior to transmitting, connect an antenna
or a 50Ω dummy load to the transceiver.
◆When using the transceiver as a base station, we recommend you
install an arrester so as to avoid fire, electric shock, damage and
injury.
◆If the antenna SWR exceeds 1.5:1 or more, the protection circuit
activates in the transceiver.Ensure that the antenna SWR is 1.5:1
or lower.
◆If the antenna dedicated for reception uses a semiconductor,
such as an active antenna, do not transmit with it nor activate the
antenna tuner.Doing so will supply power to the antenna system,
damaging the semiconductor circuits of the antenna.
CONNECTING AN AC POWER CABLE
Use the supplied AC power cable to plug to an AC
outlet with a protective grounding contact.Ensure that
the grounding lead from the AC plug has been properly
connected to the ground terminal before plugging the
AC plug into the outlet.Likewise, remove the ground
connection only after unplugging the AC plug.Failure to
do so may result in an electrical shock.
PRECAUTIONS
◆The AC power cable supplied with the K-type transceiver can only
be used for the supply voltage AC 120V.Do not use or modify the
supplied AC power cable with the UL plug for the supply voltage
AC 220V - AC 240V.
◆The AC power cable with the CE plug and the AC power cable with
the BS plug are supplied with the E-type transceiver.Use one of
the supplied cables that can correctly be plugged to an AC outlet.
GROUND CONNECTION
To avoid dangers such as electric shock, a good ground
connection is necessary.
Bury one or more grounding rods or a large copper plate
in the ground and connect it to the GND terminal on the
rear panel of the transceiver using a thick conductive wire
or a well fitted copper band plate.
PRECAUTION
◆Do not use a gas pipe, an electrical conduit pipe, a plastic water
pipe, etc., for grounding.These items will not create a proper
ground and may cause an accident or fire.
LIGHTNING ARRESTER INSTALLATION
To avoid fire, electrification, damage, and injury by the
lightning strike, install the lightning surge protector.
If a lightning storm is in the area, disconnect the antenna
cable from the transceiver.
TRANSCEIVERTILT MECHANISM
The lift-up supplementary bases are on the front bases on
the bottom of the transceiver.To position the front panel
slightly toward the upper side, pull the supplementary
bases forward to the limit.
To use the front bases, be careful not to catch your fingers
when lifting up the front bases’ mechanism.
Rear Panel
GND terminal
RX IN
ANT 1
HF/50MHz
(M-type)
ANT 2
HF/50MHz
(M-type)
ANT 3
HF/50MHz
(M-type)
ANT 4
HF/50MHz
(M-type)
AC Power Cable (Supplied)
1-2
1 INSTALLING AND CONNECTINGTHETRANSCEIVER
Index Contents
TORQUE ADJUSTMENT FOR TUNING (M) CONTROL
You can change the rotation torque of the Tuning (M)
control as desired by pinching the ring at the back of
the dial, then rotating the dial.Clockwise increases the
rotation torque and counterclockwise decreases it.
Tight Loose
Hold the ring securely, allowing you to rotate the knob.
ACCESSORIES CONNECTIONS (FRONT
PANEL)
HEADPHONES (PHONES)
The PHONES jack accepts 2-conductor (mono) or
3-conductor (stereo) headphones with an impedance of
4Ω to 32Ω (standard is 8Ω) and a 6.3 mm (1/4") diameter
plug.
While the headphones are plugged in, the audio line for
the internal speaker (or an optional external speaker) is
muted and the audio is heard through the headphones.
The following optional headphones can be used with this
transceiver:
• HS-5 (monaural) • HS-6 (monaural)
Note:
◆Headphones with a higher impedance also have a higher volume
level.
◆ Refer to "BASIC OPERATIONS" for details of configuration for the
mixing balance to the headphones output and the left and right
reverse.{page 4-23}
FRONT PANEL
GND(STBY)
GND(MIC)
NC
8V(10mA max)
MIC
PTT
DOWN
UP
USB Flash Drive and
USB Keyboard (Commercially
available)
Straight Key (Commercially available)
Paddle (Commercially available)
Headphones
(Optional or Commercially available)
Microphone
(Optional or Commercially available)
Microphone Connector
(Viewed from the Front Panel Side)
1-3
INSTALLING AND CONNECTINGTHETRANSCEIVER 1
IndexContents
MICROPHONE (MIC)
The MIC jack accepts a microphone with an impedance of
250Ω to 600Ω.
Connect the microphone plug to the MIC socket on
the front panel and screw the retaining ring until the
microphone is securely tightened.
The following optional microphones can be used with this
transceiver:
• MC-43S
• MC-60A
• MC-90
• MC-47
The following microphones cannot be used with this
transceiver.
• MC-44
• MC-44DM
• MC-45
• MC-45DM
PADDLE (PADDLE)
For CW operation using the built-in electronic keyer,
connect a keyer to the PADDLE jack.The PADDLE jack
accepts a 3-conductor plug with a 6.3 mm (1/4") diameter.
The straight key can be connected to the PADDLE jack.In
this case, select "Straight Key" from Menu 5-00, "Paddle
Jack Configuration (Front)". {page 5-18}
USB FLASH DRIVE/USB KEYBOARD ( )
You can connect any commercially available USB flash
drive or USB keyboard to the USB-A port.
Connect it securely to the (USB-A) port.
Note:
◆Do not disconnect the USB flash drive from the transceiver while it
is in use, such as while reading or writing data.Additionally, do not
turn the main power switch (I/O) OFF. {page 12-1}
◆To avoid any damage to the data, you must remove the USB flash
drive after executing Safe Removal of USB Flash drive.{page 12-1}
◆Only a USB flash drive or a keyboard can be connected to the USB
connector.
EXTERNAL SPEAKERS (EXT.SP1/EXT.SP2, 8Ω)
The transceiver is equipped with two independent
receivers.In general, audio from both receivers sounds
from the internal speaker.However, connecting an
external speaker allows you to separate the audio outputs.
On the rear panel, two jacks for external speakers are
available, allowing you to connect two external speakers.
An external speaker with an impedance of 4Ω to 8Ω
(standard is 8Ω) can be connected using the 2-conductor
(mono) plug with a 3.5 mm (1/8") diameter.
If an external speaker is connected to EXT.SP1, no audio
sounds from the internal speaker.
If an external speaker is connected to EXT.SP2, the audio
sounds from both the external speaker and the internal
speaker.
Note:
◆The EXT.SP1 and EXT.SP2 jacks with 8Ω impedance are
dedicated for external speakers.Do not connect headphones to
these jacks.Doing so will result in a high audio volume level which
may cause an auditory disorder.
◆Audio to sound from an external speaker can be selected from the
menu. {page 16-17}
（＋） （−） （＋） （−）
9
3
44 52V vd
ALC
COMP
10
5
20
10
dB
+20
+60dB
250W
15A
∞
7
5
3
1
S
PO
SWR
Id
9
3
44 52V vd
ALC
COMP
10
5
20
10
dB
+20
+60dB
250W
15A
∞
7
5
3
1
S
PO
SWR
Id
Optical Digital Cable
(Connect one piece each for input
and output)
Audio Device with an Optical Digital I/O
Terminals
External Speaker (Optional)
Straight Key (Commercially available)
Paddle (Commercially available)
Main Band Meter Sub Band Meter
Add a resistor as necessary
REAR PANEL
Meter (Commercially available)
Φ3.5 mm stereo
To DVI port
DVI cable
(E type)
1-4
1 INSTALLING AND CONNECTINGTHETRANSCEIVER
Index Contents
KEY FOR CW (KEY)
For CW operation without using the built-in electronic
keyer, the plug from a electronic key, a straight key, a
external electronic keyer or a PC keyer can be connected.
The KEY jack accepts a 2-conductor (mono) plug with a
3.5 mm (1/8") diameter.
Shorting the center pin of the jack to its outer represents
“keydown”.
Depending on how you configure the menu, you can
connect a paddle to the KEY jack and use the internal
electronic keyer instead. {page 5-18}
Note:
◆ Refer to Chapter 5 "ASSISTING YOUR SMOOTH QSO" for the
details of the built-in electronic keyer. {page 5-18}
KEYPAD (KEYPAD)
You can connect a personalized (self-made) PF keypad to
the KEYPAD connector. {page 16-7}
CONNECTION TO AUDIO DEVICESWITH OPTICAL
DIGITAL INPUT TERMINAL
With a commercially available optical digital cable an
audio device can be connected to the transceiver.
Note:
◆Connect the transceiver to the audio device using the commercially
available optical digital cable with theTOSLINK connector.
◆If the transceiver is connected to the audio device, the transceiver
may not work correctly depending on the operating environment of
your PC. {page 18-11}
◆Turn the transceiver power ( ) and audio device OFF, then
connect the transceiver to the audio device.
◆If you turn the transceiver power ( ) ON while the audio signal
sourced from the transceiver is being recorded by the audio device,
the digital processing cannot be synchronized when you turn the
transceiver power ( ) ON next time;hence, the audio device
cannot correctly record.Turn the transceiver power ( ) after the
recording by the audio device has been stopped completely.
CONNECTION TO THE EXTERNAL DISPLAY UNIT
You can connect the transceiver to an external display
using the commercial available DVI cable.The ferrite
core is supplied with the transceiver (E-type only), and to
connect the transceiver with an external display, you must
attach the ferrite core to the DVI cable.
You can view the same contents using an external
display as those that are displayed on the main
screen. {page 16-18}
Note:
◆ Use an external display with 800x600 or 848x480 resolution.
METER
Connect to a commercially available meter. {page 16-15}
1-5
INSTALLING AND CONNECTINGTHETRANSCEIVER 1
IndexContents
CONNECTIONTO A PC
The transceiver can be connected to a PC using a USB cable or an RS-232C straight-through cable.
Note:
◆Turn the transceiver and your PC OFF prior to connecting your PC to the transceiver using the cable.
◆Use the commercial available USB cable or RS-232C straight-through (not “crossed”) cable.
◆In principle, using the USB audio results in a delay.Additionally, audio interruptions may occur depending on the characteristics of your PC and
the status of the load.Use USB audio for communications where time lag is inconsequential or for recording received audio in the PC.
◆To control the transceiver via the USB connector using a PC, you need to install the virtual COM port driver onto the PC.
◆To use the USB audio, the driver available in your PC as standard will be used.You can down load the ARUA-10 USB Audio Controller from the
KENWOOD web site.
(female)
TS-990S
PC
To RS-232C Serial
Port
To USB
port
RS-232C Straight Cable
USB (B) Connector
USB cable
CONNECTION TO AN APPLICABLE TRANSCEIVER (QUICK DATA TRANSFER)
For data transfer, use an RS-232C cross-cable (female to female) to connect the transceiver COM connector to the
COM connector of the secondary transceiver. {page 16-26}
You can connect this transceiver to the following applicable transceivers:
• TS-990 series • TS-590 series • TS-480 series • TS-2000 series • TS-570 series
TS-990S (female) (female)
RS-232C Cross Cable
Applicable Transceiver
1-6
1 INSTALLING AND CONNECTINGTHETRANSCEIVER
Index Contents
CONNECTIONTOTHE LINEAR AMPLIFIER
You can connect a linear amplifier to the REMOTE connector.
Prior to activating the linear amplifier, ensure that you have configured the linear amplifier
controls. {page 16-31} {page 16-32}
10 ms is the response time from when the transceiver changes from receive to transmit to when is actually transmitted.
In operation other than CW Full Break-in, changing the menu configuration extends the response time to 25 ms (45 ms
for SSB, FM and AM modes).
Note:
◆ TL-922 have been discontinued and is no longer available.
CONNECTION TO THE TL-922
TL-922
TS-990S
Supplied 7-pin DIN Plug (Use a self-made connection cable using the 7-pin DIN
plug supplied with the transceiver.)
CONTROL RELAY
Allocate pin number 2 (COM) in the REMOTE connector to connect to
the GND of the TL-922, and pin number 4 (MKE) to the RL CONT of the
TL-922. Additionally, connect pin number 6 (ALC) to the ALC OUT of the
TL-922.
Configure Advanced Menu 11 "Linear Amplifier Control (HF Band)" to
“Active High + Relay &TX Delay Control”.
CONNECTING ATYPICAL LINEAR AMPLIFIER
To connect a commercially available linear amplifier to the transceiver, follow the instructions given in the illustration below.
Note:
◆ Use a linear amplifier that has the ALC output level in the range from -7V to -10V.
◆Refer to the instruction manual supplied with the linear amplifier for connection to the linear amplifier.
AC100~240V
50/60Hz
GND
RF INPUT RF OUT
ALC TX
Control
Mates with one of the ANT 1 to ANT 4
connectors. 3rd-party
Linear Amplier
REAR PANEL
Supplied 7-pin DIN Plug
(Use the self-made connection cable using the 7-pin DIN plug supplied
with the transceiver.)
2
4
1
6 7
3
5
ALC GND
RL CONT
GND COM
MKE
REMOTE
CONNECTOR {page 1-10}
(View from the rear panel)
1-7
INSTALLING AND CONNECTINGTHETRANSCEIVER 1
IndexContents
TX/RX CONTROL
To connect a linear amplifier, configure to enable the control signal
state in Advanced Menu 11 "Linear Amplifier Control (HF Band)" and
Advanced Menu 12 "Linear Amplier Control (50 MHz Band)", and make
the appropriate connections between the TX/RL control terminals of the
TS-990S and the linear amplier.
Note:
◆TheTX/RX control method may vary depending on the type of linear amplifier.Some linear amplifiers may enterTX mode when the control
terminal is switched to the ground line.For such a linear amplifier, allocate pin number 2 (COM) in the REMOTE connector to connect to the
GND terminal and pin number 4 (MKE) to the control terminal of the linear amplifier.
CONNECTIONTO OTHER KENWOODTRANSCEIVERS WITH ATNCTERMINAL
The connection illustrated below allows packet cluster tuning using a TH-D72A/E, TM-D710A/E, or TM-D700A/E. {page 16-27}
You can connect the TS-990S to a TM-D710A/E or RC-D710 using an optional PG-5G and a commercially available RS-
232C cross-cable.If the RS-232C cross-cable has female plugs or male plugs, use a female to male conversion plug.
You can connect the transceiver to a TM-D700A/E using a commercially available RS-232C cross-cable.
Note:
◆ TM-D700A/E has been discontinued and is no longer available.
◆Refer to the instruction manual supplied with the device with the built-inTNC for details of connection.
RC-D710 + PG-5J
TM-D700A/E
TS-990S TM-D710A/E
RC-D710 +TM-V71A/E
PG-5G
GND
RXD
TXD
5
3
2
(female)
TH-D72A/E
8
7
9-pin D-Sub
Connector (female)
9-pin D-Sub Connector (male) 9-pin D-Sub
Connector
(female)
9-pin D-Sub Connector
(female)
9-pin D-Sub Connector
(Soldered side) COM Port
φ2.5 mm (φ1/10") 3-pole Plug
2
4
1
6 7
3
5
ALC GND
(RX)
(TX) COM BRK
RL
MKE
REMOTE
CONNECTOR {page 1-10}
(View from the rear panel)
Other manuals for TS-990S
10
Table of contents
Other Kenwood Transceiver manuals
Kenwood
Kenwood TS-950S Digital User manual
Kenwood
Kenwood TK-8302U User manual
Kenwood
Kenwood TM-732A User manual
Kenwood
Kenwood TR-9130 User manual
Kenwood
Kenwood TS-950SDX User manual
Kenwood
Kenwood TS-660 User manual
Kenwood
Kenwood TK-U100 User manual
Kenwood
Kenwood TK-8360E User manual
Kenwood
Kenwood TH-234 User manual
Kenwood
Kenwood TS-950 series User manual
Kenwood
Kenwood TK-3260EX User manual
Kenwood
Kenwood TK-880 series User manual
Kenwood
Kenwood ProTalk tk-3501 User manual
Kenwood
Kenwood TK-780 series User manual
Kenwood
Kenwood NX-5300 F2 User manual
Kenwood
Kenwood TK-3173K4 User manual
Kenwood
Kenwood TR-851A User manual
Kenwood
Kenwood TK-2170 SERIES User manual
Kenwood
Kenwood TK-7180 Installation and operating instructions
Kenwood
Kenwood TK-760G series User manual
