Kenwood ProTalk DIGITAL NX-P1200NV User manual

USER MANUAL
NX-P1200NV
NX-P1200AV
NX-P1202AV
NX-P1300NU
NX-P1300AU
NX-P1302AU
B5A-3583-00_EN

2
CONTENTS
MODELS COVERED BY THIS MANUAL......................................................... 4
PREPARATION ................................................................................................ 5
INSTALLING THE ANTENNA ...................................................................................... 5
INSTALLING/ REMOVING THE BATTERY PACK........................................................ 5
INSTALLING THE BELT CLIP...................................................................................... 6
INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE JACKS.................... 6
INSTALLING THE SPEAKER/ MICROPHONE OR HEADSET ................................... 7
ORIENTATION ................................................................................................. 8
BASIC OPERATION ........................................................................................ 9
POWER ON ................................................................................................................. 9
ADJUST THE VOLUME ............................................................................................... 9
SELECT A ZONE......................................................................................................... 9
SELECT A CHANNEL ................................................................................................. 9
MAKE A CALL ............................................................................................................. 9
RECEIVE VOICE ....................................................................................................... 10
POWER OFF ............................................................................................................. 10
LED Indicator Status ............................................................................................. 10
SELF-PROGRAMMING MODE ..................................................................... 11
SELF-PROGRAMMING FLOW.................................................................................. 11
DEFAULT CHANNEL SETTINGS .............................................................................. 13
ID SETUP .................................................................................................................. 19
NXDN ID Setup (Digital)........................................................................................ 19
Reserved Group Setup (Digital) ............................................................................ 20
ZONE SELECTION.................................................................................................... 22
CHANNEL SETUP..................................................................................................... 23
Frequency Setup ................................................................................................... 23
Channel Type Setup .............................................................................................. 26
TX Setup ............................................................................................................... 27
QT/DQT Setup (Analog)........................................................................................ 29
RAN Setup (Digital) ............................................................................................... 32
TX Power Setup..................................................................................................... 33
CHANNEL CONFIRMATION MODE ............................................................. 34
BUTTON FUNCTION PROGRAMMING MODE ............................................ 35
FUNCTIONS LIST ..................................................................................................... 35
PROGRAMMABLE FUNCTIONS .............................................................................. 37
Button Lock ........................................................................................................... 37
Calling Alert ........................................................................................................... 37
External Speaker................................................................................................... 37

3
Home Channel ...................................................................................................... 38
Home Channel Select ........................................................................................... 38
Individual Reply ..................................................................................................... 39
Low Transmit Power............................................................................................... 40
Monitor .................................................................................................................. 40
Monitor Momentary ............................................................................................... 40
Scan ...................................................................................................................... 40
Scan Temporary Delete ......................................................................................... 40
Scrambler/ Encryption ........................................................................................... 41
Speaker Attenuation .............................................................................................. 41
Squelch Off............................................................................................................ 41
Squelch Off Momentary......................................................................................... 41
Super Lock ............................................................................................................ 42
Zone Down ............................................................................................................ 42
Zone Up................................................................................................................. 42
Channel Down....................................................................................................... 42
Channel Up ........................................................................................................... 42
OTHER PROGRAM FUNCTIONS ................................................................. 43
SECOND PTT ........................................................................................................... 43
CW MESSAGE .......................................................................................................... 43
FIXED VOLUME......................................................................................................... 43
RX/TX FREQUENCY SCAN...................................................................................... 43
ZONE SELECT .......................................................................................................... 43
VOICE OPERATED TRANSMISSION (VOX)............................................................. 44
VOX Type............................................................................................................... 44
VOX Function Setup .............................................................................................. 44
VOX Operation ...................................................................................................... 45
Semi-VOX Operation ............................................................................................. 45
BACKGROUND OPERATIONS ..................................................................... 46
TIME-OUT TIMER (TOT) ........................................................................................... 46
BATTERY SAVER ...................................................................................................... 46
LOW BATTERY WARNING........................................................................................ 46
BUSY CHANNEL LOCKOUT (BCL) .......................................................................... 46
VOICE ANNOUNCEMENT ........................................................................................ 47
ALL RESET MODE........................................................................................ 48
TROUBLESHOOTING GUIDE....................................................................... 49
SPECIFICATIONS.......................................................................................... 50

4
MODELS COVERED BY THIS MANUAL
The models listed below are covered by this manual:
NXDN/ Analog Transceiver
NX-P1200NV : VHF TRANSCEIVER
NX-P1300NU : UHF TRANSCEIVER
Analog Transceiver
NX-P1200AV : VHF TRANSCEIVER
NX-P1202AV : VHF TRANSCEIVER
NX-P1300AU : UHF TRANSCEIVER
NX-P1302AU : UHF TRANSCEIVER

5
PREPARATION
INSTALLING THE ANTENNA
Screw the antenna into the connector on the top of the
transceiver by holding the antenna at its base and turning it
clockwise until secure.
Antenna
INSTALLING/ REMOVING THE BATTERY PACK
The battery pack is not charged at the factory; charge it before use.
CAUTION
◆Do not short the battery terminals or dispose of the battery by fire.
◆Never attempt to remove the casing from the battery pack.
1Align the battery pack with the back of the
transceiver, then press the battery pack and
transceiver firmly together until the release latch on
the base of the transceiver locks.
2To remove the battery pack, lift the safety catch on
the base of the transceiver, then press the release
latch underneath the safety catch.
3While pressing the release latch, pull the battery
pack away from the transceiver.

6
INSTALLING THE BELT CLIP
If necessary, attach the belt clip using the two
supplied M3 x 8 mm binding screws.
Note:
◆If the belt clip is not installed, its mounting location
may get hot during continuous transmission or when
left sitting in a hot environment.
◆Use the Phillips #2 screwdriver.
Belt clip
M3 x 8 mm
screws
CAUTION
◆Do not use glue which is designed to prevent screw loosening when installing the
belt clip, as it may cause damage to the transceiver. Acrylic ester, which is contained
in these glues, may crack the transceiver’s back panel.
INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE
JACKS
Note:
◆For the speaker/ microphone jack, waterproof performance is guaranteed by securing
the supplied cap. Waterproof performance will not be guaranteed by connecting an
optional speaker/ microphone, etc.
◆Use the Phillips #1 screwdriver.
1If you are not using an optional speaker/
microphone or headset, install the cap over the
speaker/ microphone jacks.
2Secure the cap in place using the attached screw.
Speaker/ microphone
jack cap
Screw

7
INSTALLING THE SPEAKER/ MICROPHONE OR HEADSET
Note:
◆The transceiver is not fully water resistant when using a speaker/ microphone or
headset.
◆Use the Phillips #1 screwdriver.
1Insert the speaker/ microphone plugs into the
speaker/ microphone jacks of the transceiver.
2Place the locking bracket over the speaker/
microphone plugs so that the locking tabs insert
into the transceiver grooves.
3Secure the locking bracket in place using the
attached screw.
Speaker/ microphone
locking bracket
Screw

8
ORIENTATION
ab c
d
e
f
Battery pack
Microphone
Antenna
Speaker
aSelector
Rotate to change the operating channel.
bLED indicator
Refer to the “LED Indicator Status” {p. 10}.
cPower switch/ Volume control
Turn clockwise to switch the transceiver ON. To switch the transceiver OFF,
turn counterclockwise until a click sounds. Rotate to adjust the volume level.
dPTT (Push to Talk) switch
Press and hold, then speak into the microphone to transmit.
eSide 1 button
Press to activate its programmable function.
Default Function
Press None (No function)
Press and hold Zone Up
• For function descriptions and details on how to change the function
of the Side 1 button, refer to “BUTTON FUNCTION PROGRAMMING
MODE” {p. 35}.
fSide 2 button
Press to activate its programmable function.
Default Function
Press None (No function)
Press and hold Zone Down
• For function descriptions and details on how to change the function
of the Side 2 button, refer to “BUTTON FUNCTION PROGRAMMING
MODE” {p. 35}.

9
BASIC OPERATION
POWER ON
Turn the Power switch/ Volume control clockwise to switch the
transceiver power ON.
• Power-on tone will sound.
ADJUST THE VOLUME
Rotate the Power switch/ Volume control to adjust the volume.
• Clockwise increases the volume and counterclockwise decreases the volume.
Note:
◆To adjust the volume using background noise as a reference in Analog mode, use the
[Monitor] or [Squelch O] function.
SELECT A ZONE
Press and hold the Side 1 button for 1 second to increase the
Zone number (Zone 1Zone 2Zone 3Zone 4Zone 1).
Press and hold the Side 2 button for 1 second to decrease the
Zone number (Zone 4Zone 3Zone 2Zone 1Zone 4).
• Side 1 and Side 2 buttons are the default settings.
SELECT A CHANNEL
Rotate the Selector to select your desired channel.
MAKE A CALL
Press and hold the PTT switch, then speak into the microphone
using your normal speaking voice.
• Hold the microphone approximately 3 to 4 cm (1.5 inches)
from your mouth.
Release the PTT switch to receive.
Note:
◆When the battery pack voltage becomes too low, transmission will stop and an alert
tone will sound.

10
RECEIVE VOICE
The LED lights green.
When the other party transmits it, you hear the voice of the other party.
POWER OFF
After use, turn off the power. To switch the transceiver
power OFF, turn the Power switch/ Volume control fully
counterclockwise, until a click sounds.
LED Indicator Status
Indicator Color Meaning
Lights red Transmitting
Lights green Receiving a call.
Blinks red Battery power is low.
Blinks green Scanning

11
SELF-PROGRAMMING MODE
This mode allows you to program the certain transceiver’s settings of zone and
channel.
SELF-PROGRAMMING FLOW
Self-programming flow has two patterns depending on the model.
NX-P1200NV/ NX-P1300NU (NXDN/ Analog Transceiver)
B
AB A
D
C
[Side 1] + [PTT] + Power ON
[PTT]
[PTT]
Select NXDN ID
CHANNEL SETUP
NXDN ID
Setup Mode
[Selector] : Select digit
[Side 1] : Up
[Side 2] : Down
[PTT] [PTT]
[PTT]
Select Reserved Group ID
Reserved Group
Setup Mode
[Selector] : Select digit
[Side 1] : Up
[Side 2] : Down
[PTT]
[PTT]
Frequency
Setup Mode
Frequency
Table
Selection
[Side 1] / [Side 2]
[PTT]
[PTT]
Channel Type
Setup Mode
Channel Type
Selection
[PTT]
[PTT]
TX
Setup Mode
Transmit
Mode
Selection
[PTT]
[PTT]
QT/DQT
Setup Mode
QT/DQT Table
Selection
[PTT]
[PTT]
RAN
Setup Mode
RAN Table
Selection
[PTT]
[PTT]
TX Power
Setup Mode
Transmit
Power
Selection
[PTT]
Confirmation
Setup Mode
ID SETUP/ ZONE SELECTION
Returns to the
currently set
zone number.
Release [Side 1] + [PTT]
*2 *1*3*4
*1 : Channel type is selected from “NXDN” (Digital), “Analog” or “Mixed” (Dual).
*2 : TX Setup Mode can be selected when Channel Type is “Mixed” (Dual).
*3 : QT/DQT Setup Mode can be selected when Channel Type is “Analog” or “Mixed” (Dual).
*4 : RAN Setup Mode can be selected when Channel Type is “NXDN” (Digital) or “Mixed” (Dual).
[Side 1] / [Side 2] [Side 1] / [Side 2] [Side 1] / [Side 2] [Side 1] / [Side 2] [Side 1] / [Side 2]
[Selector] : Change channel number.
Power OFF and then ON
Return to normal operation
Zone 1
Setup
Mode
[PTT]
Zone 2
Setup
Mode
[PTT]
Zone 3
Setup
Mode
[Side 2]
[Side 1]
[Side 2]
[Side 1]
[Side 2]
[Side 1]
[PTT]
Zone 4
Setup
Mode
D
C
[Side 2]
[Side 1]

12
NX-P1200AV/ NX-P1202AV/ NX-P1300AU/ NX-P1302AU (Analog
Transceiver)
B
AB A
D
C
[Side 1] + [PTT] + Power ON
CHANNEL SETUP
[PTT]
[PTT]
[PTT]
Frequency
Setup Mode
Frequency
Table
Selection
[Side 1] / [Side 2]
[PTT]
[PTT]
QT/DQT
Setup Mode
QT/DQT Table
Selection
[PTT]
[PTT]
TX Power
Setup Mode
Transmit
Power
Selection
[PTT]
Confirmation
Setup Mode
ZONE SELECTION
Returns to the
currently set
zone number.
Release [Side 1] + [PTT]
[Side 1] / [Side 2] [Side 1] / [Side 2]
Zone 1
Setup
Mode
[PTT]
Zone 2
Setup
Mode
[PTT]
Zone 3
Setup
Mode
[Side 2]
[Side 1]
[Side 2]
[Side 1]
[Side 2]
[Side 1]
[PTT]
Zone 4
Setup
Mode
D
C
[Side 2]
[Side 1]
[Selector] : Change channel number.
Power OFF and then ON
Return to normal operation

13
DEFAULT CHANNEL SETTINGS
This transceiver allows you to reprogram each of the channels with different
frequencies and QT tone/DQT code (Analog)/ RAN (NXDN (Digital)) settings.
NX-P1200NV
Channel
Number
Zone 1/ Zone 2 (Analog) Zone 3/ Zone 4 (Digital)
Table
No.
Frequency
(MHz)
Table
No. QT (Hz) Table No.
Frequency
(MHz)
Table
No. RAN
1 1 151.6250 1 67.0 1 151.6250 1 1
2 1 151.6250 4 77.0 1 151.6250 2 2
3 1 151.6250 8 88.5 1 151.6250 3 3
4 1 151.6250 29 179.9 1 151.6250 4 4
5 1 151.6250 12 100.0 1 151.6250 5 5
6 2 151.9550 1 67.0 2 151.9550 1 1
7 2 151.9550 6 82.5 2 151.9550 2 2
8 2 151.9550 10 94.8 2 151.9550 3 3
9 2 151.9550 29 179.9 2 151.9550 4 4
10 2 151.9550 12 100.0 2 151.9550 5 5
11 20 154.4900 1 67.0 20 154.4900 1 1
12 21 154.5150 1 67.0 21 154.5150 1 1
13 10 151.5125 1 67.0 10 151.5125 1 1
14 12 151.6850 1 67.0 12 151.6850 1 1
15 5 151.7000 1 67.0 5 151.7000 1 1
16 6 151.7600 1 67.0 6 151.7600 1 1
Compatible KENWOOD Model
Zone Number Model Name
Zone 1/ Zone 2 NX-P1200AV (Zone 1 ~ 4)/ NX-P1202AV (Zone 2 ~ 4)/
NX-240 (Analog Mode)/ TK-2402V
Zone 3/ Zone 4 NX-240 (Digital Mode)

14
NX-P1200AV (Analog Transceiver)
Channel
Number
Zone 1 ~ Zone 4
Table
No.
Frequency
(MHz)
Table
No. QT (Hz)
1 1 151.6250 1 67.0
2 1 151.6250 4 77.0
3 1 151.6250 8 88.5
4 1 151.6250 29 179.9
5 1 151.6250 12 100.0
6 2 151.9550 1 67.0
7 2 151.9550 6 82.5
8 2 151.9550 10 94.8
9 2 151.9550 29 179.9
10 2 151.9550 12 100.0
11 20 154.4900 1 67.0
12 21 154.5150 1 67.0
13 10 151.5125 1 67.0
14 12 151.6850 1 67.0
15 5 151.7000 1 67.0
16 6 151.7600 1 67.0
Compatible KENWOOD Model
Zone Number Model Name
Zone 1 ~ Zone 4 NX-P1200NV (Zone 1/ 2)/ NX-P1202AV (Zone 2 ~ 4)/
NX-240 (Analog Mode)/ TK-2402V

15
NX-P1202AV (Analog Transceiver)
Channel
Number
Zone 1 Zone 2 ~ Zone 4
Table
No.
Frequency
(MHz)
Table
No. QT (Hz) Table No.
Frequency
(MHz)
Table
No. QT (Hz)
1 20 154.4900 1 67.0 1 151.6250 1 67.0
2 21 154.5150 1 67.0 1 151.6250 4 77.0
3 1 151.6250 1 67.0 1 151.6250 8 88.5
4 2 151.9550 1 67.0 1 151.6250 29 179.9
5 10 151.5125 1 67.0 1 151.6250 12 100.0
6 12 151.6850 1 67.0 2 151.9550 1 67.0
7 15 151.7750 1 67.0 2 151.9550 6 82.5
8 26 158.4000 1 67.0 2 151.9550 10 94.8
9 1 151.6250 4 77.0 2 151.9550 29 179.9
10 1 151.6250 8 88.5 2 151.9550 12 100.0
11 1 151.6250 29 179.9 20 154.4900 1 67.0
12 2 151.9550 6 82.5 21 154.5150 1 67.0
13 2 151.9550 10 94.8 10 151.5125 1 67.0
14 2 151.9550 29 179.9 12 151.6850 1 67.0
15 5 151.7000 1 67.0 5 151.7000 1 67.0
16 6 151.7600 1 67.0 6 151.7600 1 67.0
Compatible KENWOOD Model
Zone Number Model Name
Zone 1 TK-2400
Zone 2 ~ Zone 4 NX-P1200NV (Zone 1/ 2) NX-P1200AV (Zone 1 ~ 4)/
NX-240 (Analog Mode)/ TK-2402V

16
NX-P1300NU (NXDN/ Analog Transceiver)
Channel
Number
Zone 1/ Zone 2 (Analog) Zone 3 (Digital)
Table
No.
Frequency
(MHz)
Table
No. QT (Hz) Table No.
Frequency
(MHz)
Table
No. RAN
1 1 464.5000 1 67.0 1 464.5000 1 1
2 1 464.5000 4 77.0 1 464.5000 2 2
3 1 464.5000 8 88.5 1 464.5000 3 3
4 1 464.5000 29 179.9 1 464.5000 4 4
5 1 464.5000 12 100.0 1 464.5000 5 5
6 2 464.5500 1 67.0 2 464.5500 1 1
7 2 464.5500 6 82.5 2 464.5500 2 2
8 2 464.5500 10 94.8 2 464.5500 3 3
9 2 464.5500 29 179.9 2 464.5500 4 4
10 2 464.5500 12 100.0 2 464.5500 5 5
11 22 461.3625 3 74.4 22 461.3625 1 1
12 30 464.4875 5 79.7 30 464.4875 1 1
13 32 464.5375 7 85.4 32 464.5375 1 1
14 34 466.0375 9 91.5 34 466.0375 1 1
15 36 466.0875 11 97.4 36 466.0875 1 1
16 38 466.1375 13 103.5 38 466.1375 1 1
Channel
Number
Zone 4 (Digital)
Table
No.
Frequency
(MHz)
Table
No. RAN
1 2 464.5500 1 1
2 8 467.9250 1 1
3 9 461.0375 1 1
4 10 461.0625 1 1
5 11 461.0875 1 1
6 12 461.1125 1 1
7 13 461.1375 1 1
8 14 461.1625 1 1
9 1 464.5000 1 1
10 3 467.7625 1 1
11 4 467.8125 1 1
12 5 467.8500 1 1
13 6 467.8750 1 1
14 7 467.9000 1 1
15 15 461.1875 1 1
16 16 461.2125 1 1
Compatible KENWOOD Model
Zone Number Model Name
Zone 1/ Zone 2 NX-P1300AU (Zone 1 ~ 4)/ NX-P1302AU (Zone 2 ~ 4)/
NX-340 (Analog Mode)/ TK-3402U
Zone 3 NX-340 (Digital Mode)
Zone 4 NX-P500 (Digital Mode)

17
NX-P1300AU (Analog Transceiver)
Channel
Number
Zone 1 ~ Zone 4
Table
No.
Frequency
(MHz)
Table
No. QT (Hz)
1 1 464.5000 1 67.0
2 1 464.5000 4 77.0
3 1 464.5000 8 88.5
4 1 464.5000 29 179.9
5 1 464.5000 12 100.0
6 2 464.5500 1 67.0
7 2 464.5500 6 82.5
8 2 464.5500 10 94.8
9 2 464.5500 29 179.9
10 2 464.5500 12 100.0
11 22 461.3625 3 74.4
12 30 464.4875 5 79.7
13 32 464.5375 7 85.4
14 34 466.0375 9 91.5
15 36 466.0875 11 97.4
16 38 466.1375 13 103.5
Compatible KENWOOD Model
Zone Number Model Name
Zone 1 ~ Zone 4 NX-P1300NU (Zone 1/ 2)/ NX-P1302AU (Zone 2 ~ 4)/
NX-340 (Analog Mode)/ TK-3402U

18
NX-P1302AU (Analog Transceiver)
Channel
Number
Zone 1 Zone 2 ~ Zone 4
Table
No.
Frequency
(MHz)
Table
No. QT (Hz) Table No.
Frequency
(MHz)
Table
No. QT (Hz)
1 2 464.5500 1 67.0 1 464.5000 1 67.0
2 8 467.9250 1 67.0 1 464.5000 4 77.0
3 9 461.0375 1 67.0 1 464.5000 8 88.5
4 10 461.0625 1 67.0 1 464.5000 29 179.9
5 11 461.0875 1 67.0 1 464.5000 12 100.0
6 12 461.1125 1 67.0 2 464.5500 1 67.0
7 13 461.1375 1 67.0 2 464.5500 6 82.5
8 14 461.1625 1 67.0 2 464.5500 10 94.8
9 1 464.5000 1 67.0 2 464.5500 29 179.9
10 3 467.7625 1 67.0 2 464.5500 12 100.0
11 4 467.8125 1 67.0 22 461.3625 3 74.4
12 5 467.8500 1 67.0 30 464.4875 5 79.7
13 6 467.8750 1 67.0 32 464.5375 7 85.4
14 7 467.9000 1 67.0 34 466.0375 9 91.5
15 15 461.1875 1 67.0 36 466.0875 11 97.4
16 16 461.2125 1 67.0 38 466.1375 13 103.5
Compatible KENWOOD Model
Zone Number Model Name
Zone 1 TK-3400/ NX-P500 (Analog Mode)
Zone 2 ~ Zone 4 NX-P1300NU (Zone 1/ 2)/ NX-P1300AU (Zone 1 ~ 4)/
NX-340 (Analog Mode)/ TK-3402U

19
ID SETUP
NXDN ID Setup (Digital)
NXDN ID Setup allows you to configure an identification code. NXDN ID (Own unit
ID) can be used to identify the transceiver in an NXDN System.
You can set the NXDN ID from 00001 to 65519. The default NXDN ID is “00001”.
To set the NXDN ID
1With the transceiver power OFF, press and hold the Side 1 button and PTT
switch while turning the transceiver power ON.
• Continue to hold the Side 1 button and PTT switch until the LED lights
yellow and the transceiver announces “Self”.
2Release the Side 1 button and PTT switch to enter the ID SETUP/ ZONE
SELECTION.
• The transceiver announces “NXDN ID”.
3Press the PTT switch to enter the NXDN ID Setup Mode.
4Turn the Selector to set the pointer to the desired digit (1 ~ 5).
• A voice announcement will inform selected number.
• If you select more than 5 digit, error beep will sound.
5Press the Side 1 to increase the number, press the Side 2 to decrease the
number (0 ~ 9).
• A voice announcement will inform selected number.
• Repeat steps 4 to 5 to select the number of each digit.
• For example, when you set the NXDN ID as “12345”, you should operate
the Selector, Side 1 and Side 2 buttons according to the following table.
Selector position 54321
Selected number 12345
6Press the PTT switch to save the settings and return to the ID SETUP/ ZONE
SELECTION.
• A voice announcement will inform you of the currently selected NXDN ID
number. For example, when “12345” is selected, voice announcement: “ID,
One, Two, Three, Four, Five”.
• Turn the transceiver power OFF and then ON return to normal operation
with new settings.
Note:
◆If no action is performed for 20 seconds, the transceiver will automatically return to
normal operation without changing any settings.

20
Reserved Group Setup (Digital)
Reserved Group Setup allows you to configure the Reserved Group ID.
Reserved Group ID is the ID that is the destination of Group Call communication
in the channel where Selcall on PTT > Call Type (NXDN) is set to “Reserved
Group”.
You can set the Reserved Group ID from “00001” to “65519”. The default ID is
“00100”.
• Only on the channels in Zone 4 of NX-P1300NU, Reserved Group function
(making a Group Call with the Reserved Group ID) can be used by default
settings.
• If you use Reserved Group function on NX-P1200NV or the other zones of NX-
P1300NU, the settings by your dealer are required.
• Reserved Group ID: 00100 is compatible with NX-P500.
• If other parties use the same frequency, changing the Reserved Group ID
and making a Group Call with a Group ID other than “00100” can prevent
unnecessary reception.
A group call is initiated to the transceiver of the same Reserved Group ID if the
PTT switch is pressed.
Transceiver A
Reserved Group
ID : 00100
Group Call receiving transceivers
Group Call
Transceiver B
Reserved Group
ID : 00100
Transceiver C
Reserved Group
ID : 00100
Transceiver D
Reserved Group
ID : 00100
To set the Reserved Group ID
1With the transceiver power OFF, press and hold the Side 1 button and PTT
switch while turning the transceiver power ON.
• Continue to hold the Side 1 button and PTT switch until the LED lights
yellow and the transceiver announces “Self”.
2Release the Side 1 button and PTT switch to enter the ID SETUP/ ZONE
SELECTION.