TK-3230
5
3-3. Operation
1. To switch the clone target/s to Clone mode, press
and hold the [PTT] and [MONI] keys while turning the
transceiver power ON.
2. Keep holding [PTT] and [MONI] keys for 1 second.
Transceiver sound key on tone and enters Clone mode
with ” ” display.
3. Wait for 2 seconds. Transceiver displays ” ”.
4. Select a channel table number using [UP] (increment
channel table) and [DOWN] (decrement channel table)
keys.
5. To switch the clone source to Clone mode, press
and hold the [PTT] and [MONI] keys while turning the
transceiver power ON.
6. Keep holding [PTT] and [MONI] keys for 1 second.
Transceiver sound key on tone and enters Clone mode
with ” ” display.
7. Wait for 2 seconds. Transceiver displays ” ”.
8. Select the same channel table number as the clone
target/s.
9. Press [PTT] on the clone source to begin data
transmission. When the clone target starts to receive
data, the LED will light green.
When the clone source finishes sending data, a
”confirmation” tone will sound with ” ” displayed.
If data transmission fails while cloning, an ”error” tone
will sound from the Target unit with ” ” displayed.
10
. If the cloning fails, no data will be available in the Target
unit when it is returned to User mode.
11
. When the cloning is successful, the Target unit’s ”Scan”,
”Key Lock” and ”Super Lock” functions will return to
their default values (Scan = OFF, Key Lock = OFF, Super
Lock = OFF).
12
. After clone has completed, it is necessary for the Target
unit to set its required ID Type of ID List for FleetSync.
This can be done by using unit’s ID List Setting Mode.
Notes:
• The dealer can clone data to two or more transceivers by
repeating the above procedures.
• If the transceiver’s Clone Mode is configured as
”Disabled”, the transceiver cannot enter Clone mode.
• The table shown below will cover the frequencies used
for wireless cloning.
• A unit cannot be a ”Source Unit” if it is unprogrammed.
If [PTT] is pressed, an ”error” tone will sound.
• Once a unit is set to be the Source, it cannot be a target
after the data has been transmitted. This protects the
data in the Source unit.
• If the Target unit is cloned unsuccessfully, ”error” tone
will sound with ” ” display.
• After 4 seconds, Target unit returns to display ” ”.
”xx” means the last selected channel table number.
• The Source unit and Target unit must be of the same
model type and destination in order for Clone to operate.
• It is not possible to read/write setup data from the clone
source/target when it is in Clone mode. But it will trigger
to go to cloning mode (TX) when try to read/write.
• Electronic interface may cause a failure in data transfer
during Wireless Clone, such as when waveforms or
electromagnetics are being performed at the workbench.
• Clone mode can be used ONLY by the authorized service
personnel.
• The Clone mode setting must be configured as ”Disable”
before being delivered to the end-user.
• When wireless Clone mode is used, the environment
must ensure that the radio wave does not leak to
outside.
• The transmit output power is automatically set to Low in
Clone mode.
• Battery saver function is automatically set to off in Clone
mode.
Channel
setup No. Frequency (MHz) Channel
setup No. Frequency (MHz)
01 464.50000 29 462.91250
02 464.55000 30 464.48750
03 467.76250 31 464.51250
04 467.81250 32 464.53750
05 467.85000 33 464.56250
06 467.87500 34 466.03750
07 467.90000 35 466.06250
08 467.92500 36 466.08750
09 461.03750 37 466.11250
10 461.06250 38 466.13750
11 461.08750 39 466.16250
12 461.11250 40 466.18750
13 461.13750 41 466.21250
14 461.16250 42 466.23750
15 461.18750 43 466.26250
16 461.21250 44 466.28750
17 461.23750 45 466.31250
18 461.26250 46 466.33750
19 461.28750 47 466.36250
20 461.31250 48 467.78750
21 461.33750 49 467.83750
22 461.36250 50 467.86250
23 462.76250 51 467.88750
24 462.78750 52 467.91250
25 462.81250 53 469.48750
26 462.83750 54 469.51250
27 462.86250 55 469.53750
28 462.88750 56 469.56250
User can select channel frequency from above.
Table 1 Cloning frequency table
REALIGNMENT
