Kenwood TK-D340 User manual

B5A-0931-10 (M, C)
VHF DIGITAL TRANSCEIVER
UHF DIGITAL TRANSCEIVER
USER GUIDE
TK-D240
TK-D340
TK-D348R
This User Guide covers only the basic operations
of your radio. Ask your dealer for information on
any customized features they may have added to
your radio. For using details instruction manual
(User Manual), refer to the following URL.
http://manual.kenwood.com/en_contents/search/keyword

2
THANK YOU
We are grateful you have chosen KENWOOD for your Digital
Transceiver applications.
CONTENTS
NOTICES TO THE USER.................................................. 3
PRECAUTIONS.............................................................................. 4
UNPACKING AND CHECKING EQUIPMENT............................ 9
SUPPLIED ACCESSORIES ............................................................ 9
PREPARATION ............................................................ 9
INSTALLING THE ANTENNA ......................................................... 9
INSTALLING THE CHANNEL STOPPER....................................... 10
INSTALLING/ REMOVING THE BATTERY PACK .......................... 11
INSTALLING THE BELT CLIP....................................................... 12
INSTALLING THE CAP OVER THE SPEAKER/ MICROPHONE
JACKS......................................................................................... 12
INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE
(OR HEADSET)............................................................................ 13
ORIENTATION ............................................................14
BASIC OPERATIONS ....................................................15
SWITCHING POWER ON/OFF...................................................... 15
ADJUSTING THE VOLUME.......................................................... 15
SELECTING A ZONE AND CHANNEL ........................................... 15
TRANSMITTING.......................................................................... 15
RECEIVING.................................................................................. 16
LED INDICATOR STATUS ............................................................ 16
Firmware Copyrights
The title to and ownership of copyrights for firmware embedded in KENWOOD
product memories are reserved for JVC KENWOOD Corporation.

3
NOTICES TO THE USER
◆Government law prohibits the operation of unlicensed radio
transmitters within the territories under government control.
◆Illegal operation is punishable by fine and/or imprisonment.
◆Refer service to qualified technicians only.
Safety: It is important that the operator is aware of, and
understands, hazards common to the operation of any
transceiver.
One or more of the following statements may be applicable:
FCC WARNING
This equipment generates or uses radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the
modifications are expressly approved by the party responsible/
JVC KENWOOD. The user could lose the authority to operate this equipment if
an unauthorized change or modification is made.
INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can generate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee
that the interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to which
the receiver is connected.
• Consult the dealer for technical assistance.
The AMBE+2TM voice coding Technology embodied in this product is protected
by intellectual property rights including patent rights, copyrights and trade
secrets of Digital Voice Systems, Inc. This voice coding Technology is licensed
solely for use within this Communications Equipment. The user of this
Technology is explicitly prohibited from attempting to extract, remove, decompile,
reverse engineer, or disassemble the Object Code, or in any other way convert
the Object Code into a human-readable form. U.S. Patent Nos. #8,315,860,
#8,595,002, #6,199,037, #6,912,495, #8,200,497, #7,970,606, and #8,359,197.

4
PRECAUTIONS
• Do not charge the transceiver and battery pack when they are wet.
• Ensure that there are no metallic items located between the
transceiver and the battery pack.
• Do not use options not specified by KENWOOD.
• If the die-cast chassis or other transceiver part is damaged, do not
touch the damaged parts.
• If a headset or headphone is connected to the transceiver, reduce
the transceiver volume. Pay attention to the volume level when
turning the squelch off.
• Do not place the microphone cable around your neck while near
machinery that may catch the cable.
• Do not place the transceiver on unstable surfaces.
• Ensure that the end of the antenna does not touch your eyes.
• When the transceiver is used for transmission for many hours, the
radiator and chassis will become hot. Do not touch these locations
when replacing the battery pack.
• Do not immerse the transceiver in water.
• Always switch the transceiver power off before installing optional
accessories.
• The charger is the device that disconnects the unit from the AC
mains line. The AC plug should be readily accessible.
• To dispose of batteries, be sure to comply with the laws and
regulations in your country or region.
WARNING
Turn the transceiver power off in the following locations:
• In explosive atmospheres (inflammable gas, dust particles,
metallic powders, grain powders, etc.).
• While taking on fuel or while parked at gasoline service stations.
• Near explosives or blasting sites.
• In aircraft. (Any use of the transceiver must follow the
instructions and regulations provided by the airline crew.)
• Where restrictions or warnings are posted regarding the use of
radio devices, including but not limited to medical facilities.
• Near persons using pacemakers.

5
CAUTION
• Do not disassemble or modify the transceiver for any reason.
• Do not place the transceiver on or near airbag equipment while
the vehicle is running. When the airbag inflates, the transceiver
may be ejected and strike the driver or passengers.
• Do not transmit while touching the antenna terminal or if
any metallic parts are exposed from the antenna covering.
Transmitting at such a time may result in a high-frequency burn.
• If an abnormal odor or smoke is detected coming from the
transceiver, switch the transceiver power off immediately,
remove the battery pack from the transceiver, and contact your
KENWOOD dealer.
• Use of the transceiver while you are driving may be against traffic
laws. Please check and observe the vehicle regulations in your
area.
• Do not expose the transceiver to extremely hot or cold
conditions.
• Do not carry the battery pack (or battery case) with metal
objects, as they may short the battery terminals.
• Danger of explosion if the battery is incorrectly replaced; replace
only with the same type.
• When attaching a commercial strap to the transceiver, ensure
that the strap is durable. In addition, do not swing the transceiver
around by the strap; you may inadvertently strike and injure
another person with the transceiver.
• If a commercially available neck strap is used, take care not to
let the strap get caught on nearby machine.
• When operating the transceiver in areas where the air is dry,
it is easy to build up an electric charge (static electricity).
When using an earphone accessory in such conditions, it is
possible for the transceiver to send an electric shock through
the earphone and to your ear. We recommend you use only
a speaker/microphone in these conditions, to avoid electric
shocks.
• Do not expose the transceiver to long periods of direct sunlight,
nor place it near heating appliances.

6
Information concerning the battery pack:
The battery pack includes flammable objects such as organic
solvent. Mishandling may cause the battery to rupture
producing flames or extreme heat, deteriorate, or cause other
forms of damage to the battery. Please observe the following
prohibitive matters.
DANGER
• Do not disassemble or reconstruct battery!
The battery pack has a safety function and protection circuit to avoid
danger. If they suffer serious damage, the battery may generate heat
or smoke, rupture, or burst into flame.
• Do not short-circuit the battery!
Do not join the + and – terminals using any form of metal (such as a
paper clip or wire). Do not carry or store the battery pack in containers
holding metal objects (such as wires, chain-necklaces or hairpins). If
the battery pack is short-circuited, excessive current will flow and the
battery may generate heat or smoke, rupture, or burst into flame. It
will also cause metal objects to heat up.
• Do not incinerate or apply heat to the battery!
If the insulator is melted, the gas release vent or safety function is
damaged, or the electrolyte is ignited, the battery may generate heat
or smoke, rupture, or burst into flame.
• Do not leave the battery near fire, stoves, or other heat
generators (areas reaching over 80°C/ 176°F)!
If the polymer separator is melted due to high temperature, an
internal short-circuit may occur in the individual cells and the battery
may generate heat or smoke, rupture, or burst into flame.
• Do not immerse the battery in water or get it wet by other
means!
If the battery’s protection circuit is damaged, the battery may charge
at extreme current (or voltage) and an abnormal chemical reaction
may occur. The battery may generate heat or smoke, rupture, or
burst into flame.
• Do not charge the battery near fire or under direct sunlight!
If the battery’s protection circuit is damaged, the battery may charge
at extreme current (or voltage) and an abnormal chemical reaction
may occur. The battery may generate heat or smoke, rupture, or
burst into flame.

7
DANGER
• Use only the specified charger and observe charging
requirements!
If the battery is charged in unspecified conditions (under high
temperature over the regulated value, excessive high voltage or
current over regulated value, or with a remodeled charger), it may
overcharge or an abnormal chemical reaction may occur. The battery
may generate heat or smoke, rupture, or burst into flame.
• Do not pierce the battery with any object, strike it with an
instrument, or step on it!
This may break or deform the battery, causing a short-circuit. The
battery may generate heat or smoke, rupture, or burst into flame.
• Do not jar or throw the battery!
An impact may cause the battery to leak, generate heat or smoke,
rupture, and/or burst into flame. If the battery’s protection circuit
is damaged, the battery may charge at an abnormal current (or
voltage), and an abnormal chemical reaction may occur. The battery
may generate heat or smoke, rupture, or burst into flame.
• Do not use the battery pack if it is damaged in any way!
The battery may generate heat or smoke, rupture, or burst into
flame.
• Do not solder directly onto the battery!
If the insulator is melted or the gas release vent or safety function is
damaged, the battery may generate heat or smoke, rupture, or burst
into flame.
• Do not reverse the battery polarity (and terminals)!
When charging a reversed battery, an abnormal chemical reaction
may occur. In some cases, an unexpected large amount of current
may flow upon discharging. The battery may generate heat or
smoke, rupture, or burst into flame.
• Do not reverse-charge or reverse-connect the battery!
The battery pack has positive and negative poles. If the battery pack
does not smoothly connect with a charger or operating equipment,
do not force it; check the polarity of the battery. If the battery pack is
reverse-connected to the charger, it will be reverse-charged and an
abnormal chemical reaction may occur. The battery may generate
heat or smoke, rupture, or burst into flame.

8
DANGER
• Do not touch a ruptured and leaking battery!
If the electrolyte liquid from the battery gets into your eyes, wash
your eyes with fresh water as soon as possible, without rubbing your
eyes. Go to the hospital immediately. If left untreated, it may cause
eye-problems.
WARNING
• Do not charge the battery for longer than the specified time!
If the battery pack has not finished charging even after the regulated
time has passed, stop it. The battery may generate heat or smoke,
rupture, or burst into flame.
• Do not place the battery pack into a microwave or high
pressure container!
The battery may generate heat or smoke, rupture, or burst into
flame.
• Keep ruptured and leaking battery packs away from fire!
If the battery pack is leaking (or the battery emits a bad odor),
immediately remove it from flammable areas. Electrolyte leaking
from battery can easily catch on fire and may cause the battery to
generate smoke or burst into flame.
• Do not use an abnormal battery!
If the battery pack emits a bad odor, appears to have different
coloring, is deformed, or seems abnormal for any other reason,
remove it from the charger or operating equipment and do not use
it. The battery may generate heat or smoke, rupture, or burst into
flame.

9
UNPACKING AND CHECKING EQUIPMENT
Carefully unpack the transceiver. If any of the items listed
below are missing or damaged, file a claim with the carrier
immediately.
SUPPLIED ACCESSORIES
• Antenna <TK-D340 C type only>............................................1
• Speaker/ microphone jack cover ............................................1
• Speaker/ microphone locking bracket.....................................1
• Belt clip (KBH-10)................................................................... 1
• Screw (M3 x 8 mm) ................................................................2
• Channel stopper .....................................................................1
• FPC <TK-D348R only>...........................................................1
• Threaded Spacer <TK-D348R only>...................................... 4
• Pan head (machine) screw (M2 x 4 mm) <TK-D348R only>..4
• User Guide .............................................................................1
PREPARATION
INSTALLING THE ANTENNA
Antenna Screw the antenna into the connector on
the top of the transceiver by holding the
antenna at its base and turning it clockwise
until secure.
Note:
◆The antenna is neither a handle, a key
ring retainer, nor a speaker/ microphone
attachment point. Using the antenna in these
ways may damage the antenna and degrade
your transceiver’s performance.

10
INSTALLING THE CHANNEL STOPPER
You can set the channel stopper position for channels 2, 4,
6, 8, 10, 12, and 14. Inserting the Channel stopper prevents
unnecessarily selecting channels which do not exist.
• Selecting a channel which does not exist causes a continuous error
tone to sound.
1 Set the Channel selector to channel 1, then pull the Channel
selector knob off the transceiver.
• If the Channel selector is not positioned at channel 1, the knob may
not install correctly and the channel may be unable to change.
2 Insert the channel stopper.
3 Set the arrow of the Channel stopper to the highest channel
number for the transceiver.
4 Reinsert the Channel selector knob.
Channel stopper Arrow

11
INSTALLING/ REMOVING THE BATTERY PACK
The battery pack is not charged at the factory; charge it before
use.
CAUTION
◆Do not short the battery terminals or dispose of the battery by
fire.
◆Never attempt to remove the casing from the battery pack.
1Align the battery pack with
the back of the transceiver,
then press the battery pack
and transceiver firmly together
until the release latch on the
base of the transceiver locks.
2To remove the battery pack, lift
the safety catch on the base
of the transceiver, then press
the release latch underneath
the safety catch.
3While pressing the release
latch, pull the battery pack
away from the transceiver.

12
INSTALLING THE BELT CLIP
Belt clip If necessary, attach the belt clip
using the two supplied M3 x 8 mm
screws.
Note:
◆If the belt clip is not installed, its
mounting location may get hot during
continuous transmission or when left
sitting in a hot environment.
CAUTION
◆Do not use glue which is designed to prevent screw loosening
when installing the belt clip, as it may cause damage to the
transceiver. Acrylic ester, which is contained in these glues,
may crack the transceiver’s back panel.
INSTALLING THE CAP OVER THE SPEAKER/
MICROPHONE JACKS
Install the cap over the speaker/ microphone jacks when not
using an optional speaker/ microphone or headset.
Note:
◆To keep the transceiver water resistant, you must cover the speaker/
microphone jacks with the supplied cap.
1Place the cap over the jacks so that the
locking tabs insert into the transceiver
grooves.
2While holding the cap in place, push it
towards the bottom of the transceiver
until the tabs on the cap click into place.

13
• To remove the cap, hold the top of the cap in place with your finger
while inserting a 2 mm or smaller flat blade screwdriver under
the bottom of the cap. Slowly slide the screwdriver in until its tip
touches the tab inside the cap, then gently pry the cap up (handle of
screwdriver moving away from the transceiver) to remove the cap.
INSTALLING THE OPTIONAL SPEAKER/ MICROPHONE
(OR HEADSET)
Note:
◆The transceiver is not fully water resistant when using a speaker/
microphone or headset.
1Insert the speaker/ microphone (or
headset) plugs into the speaker/
microphone jacks of the transceiver.
2Place the locking bracket over the
speaker/ microphone (or headset)
plugs so that the locking tabs insert
into the transceiver grooves.
• Push down on the locking bracket to
slide it into place.
3While holding the locking bracket in
place, push it towards the bottom of
the transceiver until the tabs on the
bracket click into place.
• To remove the locking bracket, push
the bracket up from the base.

14
ORIENTATION
Battery pack
Antenna
Microphone Speaker
aSelector
Rotate to change the operating channel.
bLED indicator
For the LED indicator status, refer to page 16.
cPower switch/ Volume control
Turn clockwise to switch ON the transceiver. To switch OFF
the transceiver, turn counterclockwise until a click sounds.
Rotate to adjust the volume level.
dPTT (Push to Talk) switch
Press and hold, then speak into the microphone to transmit.
eSide 1 key
Press to activate its programmable function.
fSide 2 key
Press to activate its programmable function.
gSpeaker/ microphone jacks
Insert the Speaker/ microphone or Headset plug into this jack.

15
BASIC OPERATIONS
SWITCHING POWER ON/OFF
Turn the Power switch/ Volume control clockwise to switch the
transceiver ON.
Turn the Power switch/ Volume control counterclockwise fully
to switch the transceiver OFF.
ADJUSTING THE VOLUME
Rotate the Power switch/ Volume control to adjust the volume.
Clockwise increases the volume and counterclockwise
decreases it.
SELECTING A ZONE AND CHANNEL
1Select the desired zone using the key programmed as
[Zone Up] or [Zone Down].
• Each zone contains a group of channels.
2Select the desired channel using the Selector (default).
• Each channel is programmed with settings for transmitting and
receiving.
TRANSMITTING
1Select the desired zone and channel.
2Press the key programmed as [Monitor] or [Squelch Off] to
check whether or not the channel is free.
• If the channel is busy, wait until it becomes free.
3Press the PTT switch and speak into the microphone.
Release the PTT switch to receive.
• For best sound quality, hold the transceiver approximately
3 ~ 4 cm from your mouth.

16
RECEIVING
Select the desired zone and channel. If signaling has been
programmed on the selected channel, you will hear a call only
if the received signal matches your transceiver settings.
Receiving Group Calls
When you receive a group call and the received group ID
matches the ID set up on your transceiver, you can hear the
caller’s voice.
Receiving Individual Calls
When you receive an individual call, a ringing tone will sound.
To respond to the call, press and hold the PTT switch and
speak into the transceiver as you would during a normal
transmission.
LED INDICATOR STATUS
Indicator Color Meaning
Lights red Transmitting
Lights green Receiving a call
Lights blue The Transceiver Password function is
programmed.
Blinks red Battery power is low while transmitting
Blinks green Scanning
Blinks orange or
blue * Receiving an encoded call (signaling, etc.)
Blinks red/orange The selected channel has not been
programmed and cannot be used.
* Your dealer can set the LED to blink either orange or blue for
Transceiver operation.

VHF 数字手持对讲机
UHF 数字手持对讲机
用户指南
TK-D240
TK-D340
TK-D348R
本用户指南只涵盖了您对讲机的基本操作。关于经
销商可能给您的对讲机添加的任何定制功能的信
息，请询问您的经销商。关于使用说明书（用户手
册）的使用详情，请参阅以下 URL。
http://manual.kenwood.com/en_contents/search/keyword
使用之前请阅读以下信息 ：
使用产品前请仔细阅读本用户指
南，并请妥善保管。

2
鸣谢惠购
我们感谢您选择 KENWOOD 作为您的数字对讲机应用程序。
目录
用户注意事项........................................................................ 3
注意事项...................................................................................... 4
拆开包装箱并检查设备 ......................................................... 9
随机附件...................................................................................... 9
准备工作............................................................................... 9
安装天线...................................................................................... 9
安装信道止动器........................................................................ 10
安装 /拆卸电池组 .................................................................... 11
安装皮带夹................................................................................ 12
安装扬声器 /麦克风插孔盖 .................................................... 12
安装扬声器 /麦克风选件（或头戴式耳机）.......................... 13
介绍 .................................................................................... 14
基本操作............................................................................. 15
切换电源开 /关........................................................................ 15
音量调节.................................................................................... 15
选择区域和信道........................................................................ 15
发射............................................................................................ 15
接收............................................................................................ 16
LED 指示灯状态....................................................................... 16
固件版权
JVC建伍公司保留建伍产品存储器内嵌固件的产权和版权的所有权。
出版日 ：
2017 年10 月1日

3
用户注意事项
◆政府法律禁止在政府控制的区域内使用未经当局许可的无线
电发射机。
◆非法使用将会受到罚款或监禁处罚。
◆只能由有资格的技术人员进行维修。
安全性: 操作人员应该知道并了解对讲机操作的一般危险。
本产品所包含的A M B E +2T M 语音编码技术受Digital Voice System, Inc.
知识产权( 包括专利权、版权和贸易机密) 的保护。
该语音编码技术仅许可用于本通信设备。该技术的使用人员明确禁止
尝试提取、移除、破译、反向编译或拆除目标代码，
或以其他方式将目标代码转换为人类可读形式。美国专利编号
#8,315,860, #8,595,002, #6,199,037, #6,912,495, #8,200,497, #7,970,606,
and #8,359,197.
产品中有毒有害物质或元素的名称及含量
部件名称
有毒有害物质或元素
铅
(Pb)
汞
(Hg)
镉
(Cd)
六价铬
(Cr(VI))
多溴联苯
(PBB)
多溴二苯醚
(PBDE)
框架 ×○○×○○
安装基板 ×○○○○○
电缆 ○○○○○○
扬声器 ○○○×○○
其他(附件 )○○○×○○
本表格依据 SJ/T 11364 的规定编制。
○: 表示该有害物质在该部件所有均质材料中的含量均在 GB/T 26572 规定的限
量要求以下。
×: 表示该有害物质至少在该部件的某一均质材料中的含量超出 GB/T 26572 规
定的限量要求。
环保使用期限
此图标表示了中华人民共和国的法律所规定的环保使用期限。
只要用户在使用本产品时遵守注意事项中的各项规定， 从制造日
期开始到此图标标出的期限为止（环保使用期限）既不会污染环
境也不会产生对人体有害的物质。

4
注意事项
• 对讲机和电池潮湿时请勿对其充电。
• 对讲机和电池之间应确保无金属物品。
• 请勿使用非KENWOOD指定的选件。
• 如果压铸底盘和对讲机的其他部件损坏，请勿接触损坏的
部件。
• 如果头戴式耳麦或头戴耳机连接到对讲机上，请减小对讲机
的音量。当打开静噪时，一定要注意音量。
• 靠近各种机械和电器时，请勿将麦克风电缆挂在颈部周围，
因为机械和电器可能会使电缆缠住。
• 请勿将对讲机放置在不稳定的表面上。
• 应确保天线的末端不会碰到您的眼睛。
• 对讲机长时间用于发射时，散热器和底座会变热。更换电池
时，请勿接触这些位置。
• 请勿将对讲机浸入水中。
• 安装选件前，一定要关闭对讲机的电源。
• 充电器是将装置与交流电源线断开的设备。应随时提供交流
插头。
• 若处理电池，一定要符合您所在国家或地区的法律和法规。
警告
在下列场合要关闭对讲机的电源：
• 易爆环境（易燃气体、粉尘、金属粉末以及粒状粉末等）。
• 加油时或停在加油站时。
• 在易爆场所附近。
• 在飞机上。（对讲机的使用必须遵循机组人员的指示和规
定。）
• 在粘贴有关于无线电设备的限制或警告的场合，包括但不
限于医疗设施。
• 在使用心脏起搏器的人员附近。