Kenwood TK-P701 User manual

SERVICE MANUAL
This product uses Lead Free solder.
This product complies with the RoHS directive for the European market.
VHF FM TRANSCEIVER
TK-P701
© 2012-4 PRINTED IN JAPAN
B53-7010-10 (Y)PDF
CONTENTS
GENERAL....................................................2
SYSTEM SET-UP.........................................3
REALIGNMENT...........................................3
DISASSEMBLY FOR REPAIR.....................6
CIRCUIT DESCRIPTION .............................7
SEMICONDUCTOR DATA .........................10
COMPONENTS DESCRIPTION................11
PARTS LIST...............................................12
EXPLODEDVIEW......................................17
ADJUSTMENT...........................................18
PC BOARD
TX-RX UNIT (X57-8093-00)....................22
SCHEMATIC DIAGRAM ............................26
BLOCK DIAGRAM.....................................30
LEVEL DIAGRAM......................................32
SPECIFICATIONS......................................33
Helical antenna
(T90-1094-05)
Button knob (Side)
(K29-9490-13)
Knob (PTT)
(K29-9489-13)
Plastic cabinet assy
(A02-4135-13)
Knob (Volume)
(K29-9487-03)
Knob(Selector)
(K29-9488-03)

TK-P701
2
GENERAL
INTRODUCTION
SCOPE OFTHIS MANUAL
This manual is intended for use by experienced techni-
cians familiar with similar types of commercial grade com-
munications equipment. It contains all required service
information for the equipment and is current as of the pub-
lication date. Changes which may occur after publication
are covered by either Service Bulletins or Manual Revisions.
These are issued as required.
ORDERING REPLACEMENT PARTS
When ordering replacement parts or equipment informa-
tion, the full part identification number should be included.
This applies to all parts : components, kits, or chassis. If the
part number is not known, include the chassis or kit number
of which it is a part, and a sufficient description of the re-
quired component for proper identification.
PERSONAL SAFETY
The following precautions are recommended for personal
safety:
• DO NOT transmit until all RF connectors are verified
secure and any open connectors are properly terminated.
• SHUT OFF and DO NOT operate this equipment near
electrical blasting caps or in an explosive atmosphere.
• This equipment should be serviced by a qualified techni-
cian only.
SERVICE
This transceiver is designed for easy servicing. Refer
to the schematic diagrams, printed circuit board views, and
alignment procedures contained within.
Model TX-RX unit Frequency
range Remarks
TK-P701
X57-8093-00 136~174MHz IF1: 38.85MHz
LOC: 38.4MHz
Guaranted frequency range ......................................144~174MHz
Document Copyrights
Copyright 2012 by JVC KENWOOD Corporation. All
rights reserved.
No part of this manual may be reproduced, translated,
distributed, or transmitted in any form or by any means,
electronic, mechanical, photocopying, recording, or other-
wise, for any purpose without the prior written permission of
JVC KENWOOD Corporation.
Disclaimer
While every precaution has been taken in the preparation
of this manual, JVC KENWOOD Corporation assumes no
responsibility for errors or omissions. Neither is any liability
assumed for damages resulting from the use of the informa-
tion contained herein. JVC KENWOOD Corporation reserves
the right to make changes to any products herein at any time
for improvement purposes.

TK-P701
3
SYSTEM SET-UP
REALIGNMENT
1. Modes
Mode Function
User mode For normal use.
PC mode Used for communication between the trans-
ceiver and PC.
Data programming
mode Used to read and write frequency data and other features to and from the transceiver.
PC test mode Used to check the transceiver using the PC.
This feature is included in the FPU.
Clone mode Used to transfer programming data from
one transceiver to another.
2. How to Enter Each Mode
Mode Operation
User mode Power ON
PC mode Received commands from PC
Clone mode [PTT]+[Side]+Power ON (Two seconds)
3. PC Mode
3-1. Preface
The transceiver is programmed by using a personal com-
puter, a programming interface (KPG-22A/22U) and FPU
programming software (KPG-155D).
The programming software can be used with a PC. Fig-
ure 1 shows the setup of a PC for programming.
3-2. Connection Procedure
1. Connect the transceiver to the personal computer with
the interface cable.
Note:
• You must install the KPG-22 driver in the computer to use
the USB programming interface cable (KPG-22U).
Choose the type of transceiver
Transceiver programming
Delivery
Are you using the speaker microphone?
A personal computer, programming interface (KPG-22A/22U),
and FPU (programming software) are required for programming.
(The frequency, TX power HI/LOW, and signaling data are
programmed for the transceiver.)
YES
NO
KMC-21 or KMC-45
Speaker microphone
(Option)
Are you using the optional antenna? YES
NO
TX/RX 136~174 5.0W TK-P701
Frequency range (MHz) RF power Type
Merchandise received
Optional antenna
KRA-22 or KRA-26
User mode
Data programming mode
PC test mode PC tuning mode
PC mode
Clone mode

TK-P701
4
2. When the POWER is switched on, user mode can be
entered immediately. When the PC sends a command,
the transceiver enters PC mode.
When data is read from the transceiver, the red LED
lights.
When data is written to by the transceiver, the green LED
lights.
Note:
• The data stored in the personal computer must match
Model Name and Model Type when it is written into EE-
PROM.
• Do not press the [PTT] key during data transmission or
reception.
3-3. KPG-22A Description
(PC programming interface cable: Option)
The KPG-22A is required to interface the transceiver with
the computer.It has a circuit in its D-sub connector (KPG-22A:
9-pin) case that converts the RS-232C logic level to the TTL
level.
The KPG-22A connects the SP/MIC connector of the
transceiver to the RS-232C serial port of the computer.
3-4. KPG-22U Description
(USB programming interface cable: Option)
The KPG-22U is a cable which connects to a USB port
on a computer.
When using the KPG-22U, install the supplied CD-ROM
(with driver software) in the computer. The KPG-22U driver
runs under Windows XP,Vista or 7.
3-5. Programming Software KPG-155D Description
The KPG-155D is the programming software for the
transceiver supplied on a CD-ROM. This software runs un-
der windows XP, Vista or 7 on a PC. The software on this
disk allows a user to program the transceiver via Program-
ming interface cable (KPG-22A/22U).
Note:
• Use the FPU that matches the market when you first set
the market code and model name/frequency data to the
service unit.The unit set by mistake cannot be restored.
• Receive frequencies listed below may result in the in-
terference of reception due to the harmonics of internal
oscillators.Enter a frequency not listed in the table.
No. Frequency (MHz)
1 152.69375
2 152.69500
3 152.70000
4 152.70500
5 152.70625
6 153.59375
7 153.59500
8 153.60000
9 153.60500
10 153.60625
No. Frequency (MHz)
11 172.79375
12 172.79500
13 172.80000
14 172.80500
15 172.80625
3-6. Programming with PC
If data is transferred to the transceiver from a PC with the
FPU, the data for each set can be modified.
Data can be programmed into the EEPROM in RS-232C
format via the SP/MIC jack.
In this mode the PTT line operate as TXD and RXD data
lines respectively.
REALIGNMENT
PC KPG-22A or KPG-22U or
Illustration is KPG-22A.
FPU
Tuning cable
(E30-3216-05)
Transceiver
Transceiver
KPG-22U
PC
Gray
Gray/Black
1.5D-XV Lead wire
1.5D-XV Shield wire
+
–
+
–
SP
MIC
D-SUB
(9-pin)
KPG-22A
PC
USB
Fig. 1

TK-P701
5
REALIGNMENT
4. Clone mode
Programming data can be transferred from one trans-
ceiver to another by connecting them via their SP/MIC con-
nectors.
Cloning can be performed as described below (the trans-
mit transceiver is the source and the receive transceiver is
the target).
The following data cannot be cloned.
• Tuning data
• Model name data
• ESN data
1.Turn the source transceiver and target transceiver power
OFF.
2.Turn the source transceiver power ON while pressing the
[PTT] and [Side] keys, to enter clone mode.
3. Connect the cloning cable (part No. E30-3410-05) to the
SP/MIC connectors on the source and target transceiv-
ers.
4.Turn the target transceiver power ON.
5. Press the [Side] key on the source transceiver.The data of
the source is sent to the target.While the source is send-
ing data, red LED will light.While the target is receiving
the data, green LED will light.When cloning of data is
completed, the source red LED turned off, and the target
automatically operates in the User mode.
6. Additional targets can be continuously cloned.When
the [Side] key on the source is pressed, the data of the
source is sent to the target again. Repeat steps 3 to 5 to
clone additional transceivers.
Note:
• The Model name and Market codes must be the same in
order to clone the transceiver.
• If the transceivers clone mode is configured as “Disabled”,
the transceiver cannot enter clone mode.
• If the Read authorization password is set to the trans-
ceiver, the transceiver cannot enter to the clone mode.
• Cannot be cloned if the password (overwrite password) is
programmed to the target.
Cloning cable
(E30-3410-05)
Fig. 2

TK-P701
6
DISASSEMBLY FOR REPAIR
1. Separating the Case Assembly from the
Chassis
1. Remove the two knobs (a).
2. Remove the two screws (b).
3. Expand the right and left sides of the bottom of the case
assembly, Iift the chassis, and remove it from the case
assembly (c).
4.Taking care not to cut the speaker lead (d), open the
chassis and case assembly.
Note:
Solder the speaker wire back in its original position if you
have removed it.
d
–
+BRN
GRN
2. Removing theTX-RX unit from the
Chassis
1. Remove the packing (e).
2. Remove the 13 screws (f).
3. Remove the packing (g) and two hexagon nuts (h).
4. Remove the solder from the antenna terminal using a
soldering iron then lift the unit off (i).
Note:
When reassembling the unit in the chassis, be sure to
solder the antenna terminal.
3. Removing the Rear Panel
1. Raise the rear panel on the chassis (j).
aa
b
b
c
j
Antenna terminal
e
f
g
h
i
h

TK-P701
7
1. Frequency Configuration
The receiver utilizes double conversion. The first IF is
38.85MHz and the second IF is 450kHz. The first Local os-
cillator is supplied from the PLL circuit.
The PLL circuit in the transmitter generates the neces-
sary frequencies.
CIRCUIT DESCRIPTION
2. Receiver System
The receiver system is shown in Figure 2.
Fig. 1 Frequency configuration
Fig. 2 Receiver system
2-1. RF Amplifier Circuit
The signal coming from the antenna passes through the
transmit/receive switching diode circuit (D101, D102, and
D103) and a BPF (L210), and is then amplified by the RF
amplifier (Q204).
The resulting signal passes through a BPF (L207, L208
and L215) and goes to the mixer. These BPFs are adjusted
by variable capacitors (D201,D202 and D204). The input
voltage to the variable capacitor is a regulated voltage out-
put from the DAC (IC300).
2-2. First Mixer
The signal from the front end is mixed with the first local
oscillator signal generated in the PLL circuit by Q203 to pro-
duce a first IF frequency of 38.85 MHz.
The resulting signal passes through the XF200 MCF to
cut the adjacent spurious and provide the optimum charac-
teristics, such as adjacent frequency selectivity.
TX/RX: 136~174MHz
174.85~
212.85MHz
136~174MHz
1st MIX MCF SP
MIC
CF
450kHz
ANT
ANT
SW RF AMP IF SYSTEM
X2
doubler
PLL
VCO
38.85MHz 38.4MHz
TX
AMP RF AMP
AF
AMP
MIC
AMP
AF
filter
TCXO 19.2MHz
SP
ANT
IC200
IF,MIX,DET
Q203
1st MIX IC303
CF200
ANT
SW
Q201
X2 doubler
2nd Local
X1
TCXO
19.2MHz
BPF
BPF Q204 RF AMP XF200
MCF
Q202
IF AMP IC302 AF PA
BPF 1st Local
BPF AFfilter VR500

TK-P701
8
2-3. IF Amplifier Circuit
The first IF signal is passed through a four-pole mono-
lithic crystal filter (XF200) to remove the adjacent channel
signal.
The filtered first IF signal is amplified by the first IF ampli-
fier (Q202) and then applied to the lF system IC (IC200).
The IF system IC provides a second mixer, second local
oscillator, limiting amplifier, quadrature detector and RSSI
(Received Signal Strength Indicator).The second mixer
mixes the first IF signal with the 38.4MHz of the second lo-
cal oscillator output (TCXO X1) and produces the second IF
signal of 450kHz.
The second IF signal is passed through the ceramic filter
(CF200) to remove the adjacent channel signal. The filtered
second IF signal is amplified by the limiting amplifier and
demodulated by the quadrature detector with the ceramic
discriminator (CD201).The demodulated signal is routed to
the audio circuit.
2-4. Audio Amplifier Circuit
The demodulated signal from IC200 is amplified by
IC305, IC303 and goes to AF amplifier through IC302.
The signal then goes through an volume control (VR500),
and is routed to an audio power amplifier (IC302) where it is
amplified and output to the speaker.
To output sounds from the speaker, IC400 sends a high
signal to the SPMUT line and turns IC400 on through Q300,
Q301, Q302 and Q306.
3.Transmitter System
3-1. Microphone Amplifier Circuit
The signal from microphone amplified by IC301 and goes
through mute switch (IC300).
IC304 is composed of high-pass filter, low-pass filter and
pre-emphasis/IDC circuit.
The output signal from the DAC IC (IC300) goes to the
VCO modulation input.
Fig. 3 Microphone amplifier circuit
3-2. Driver and Final Amplifier Circuit
The signal from the T/R switch (D100 is on) is amplified
by the pre-drive amplifier (Q100) to 30mW.
The output of the pre-drive amplifier is amplified by the
drive amplifier (Q101) and the RF final amplifier (Q102) to
5.0W (1W when the power is low).
The drive amplifier and the RF final amplifier consist of
two MOS FET stages.
The output of the RF final amplifier is then passed
through the harmonic filter (LPF) and antenna switch (D101
and D102) and is applied to the antenna terminal.
CIRCUIT DESCRIPTION
BUFF X1
TCXO
VCO
LSDO
IC300
MIC
DAC
AMP
IC304
LSDO
MIC
IC301
ANT
RF FINAL
AMP ANT SW LPF
From
T/R SW
(D100)
D101,102
+B
POWC
Q102
DRIVE
AMP
Q101
VDD VG
Pre-DRIVE
AMP
Q100
R121
R122
R123
CURDET
Fig. 4 Drive and final amplifier circuit

TK-P701
9
CIRCUIT DESCRIPTION
4. Frequency Synthesizer Circuit
4-1. Frequency Synthesizer
The frequency synthesizer consists of the TCXO (X1),
VCO, PLL IC (IC1) and buffer amplifiers.
The TCXO generates 19.2MHz.The frequency stability is
5.0 ppm within the temperature range of –30 to +60°C.
The frequency tuning and modulation of the TCXO are
done to apply a voltage to pin 1 of the TCXO. The output of
the TCXO is applied to pin 1 of the PLL IC.
The VCO consists of 1VCO and covers a dual range of
the 136.00~174.00MHz and the 174.85~212.85MHz. The
VCO generates 174.85~212.85MHz for providing to the first
local signal in receive.
The PLL IC consists of a prescaler, reference divider,
phase comparator, charge pump (The frequency step of the
PLL circuit is 5 or 6.25 kHz).
PLL data is output from DATA (pin 19), CLOCK (pin 18)
and PLDL (pin 20) of the MCU (IC400).The data are input to
the PLL IC when the channel is changed or when transmis-
sion is changed to reception and vice versa.A PLL lock con-
dition is always monitored by the pin 22 (PLUL) of the MCU.
When the PLL is unlocked, the PLUL goes low.
Fig. 5 PLL block diagram
5. Control Circuit
The control consists of the MCU (IC400) and its peripher-
al circuits. It controls the TX-RX unit. IC400 mainly performs
the following;
1) Switching between transmission and reception by PTT
signal input.
2) Reading channel information, frequency, and program
data from the memory circuit.
3) Sending frequency program data to the PLL.
4) Controlling squelch on/off via the DC voltage from the
squelch circuit.
5) Controlling the audio mute circuit via the decode data
input.
6) Transmitting tone and encode data.
Note:
The EEPROM stores tuning data (Deviation, Squelch,
etc.).
Realign the transceiver after replacing the EEPROM.
6. Signaling Circuit
6-1. Encode
■Low-speed data (QT, DQT)
Low-speed data is output from pin 49 (LSDO) of the MCU
(IC400).The signal passes through a low-pass CR filter. The
signal is mixed with the audio signal and goes to the VCO
and TCXO (X1) modulation input after signal processing in
the DAC IC (IC300).
■High-speed data (DTMF)
High-speed data (HSD) is output from pin 50 (HSDO) of
the MCU.
The signal passes through a low-pass CR filter.TX devia-
tion making an adjustment by MCU is applied to the DAC IC
(IC300). The signal is mixed with the audio signal and goes
to the VCO and TCXO.
6-2. Decode
■QT/DQT
The output signal from IF IC (IC200) enters the MCU
(IC400) through IC300. IC400 determines whether the QT
or DQT matches the preset value, and controls the SPMUT
and the speaker output sounds according to the squelch re-
sults.
Fig. 6 Encode
7. Power Supply
There are five 5V power supplies for the MCU:
5M is always output while the power is on.
5C is a common 5V and is output when SAVE is not set
to ON.
5R is 5V for reception and output during reception.
5T is 5V for transmission and output during transmission.
5MS is 5V for the SP/MIC connector and the DAC IC
(IC300)
INV
VCO
PLL
MCU
IC400 CLOCK,PLDL
IC1
PLUL
8
1
5
14
RF
SWLPF To mixer
LSDO
Q6
BUFF
Q5
TCXO
X1
SW To
RF AMP
T/RSHF
(TX: Low)
D100
D200
Q1
CV AMP
DATA,
HSDO
LSDO
IC400
MCU IC300
DAC
AF
AMP
TCXO
50
49
19
20 FADJ
VCO
24
MOD
21
BEEP
18
12

TK-P701
10
SEMICONDUCTOR DATA
MCU:F2136ACNKDRB (TX-RX unit IC400)
Pin No. Signal Name I/O Function
1NC ONC
2 VREF - Reference voltage input
3 MODE I Mode select for MCU
4NC ONC
5NC ONC
6 RESET I Reset signal input
7 XOUT O Oscillation circuit
8 Vss - GND
9 XIN I Oscillation circuit
10 Vcc - Power supply
11 BSFT O Beat shift for MCU clock
12 NC O NC
13 NC O NC
14 NC O NC
15 E2WP O Write protect for EEPROM
16 E2DAT I/O Data input/output from EEPROM
17 E2CLK O Clock for EEPROM
18 CLOCK O Clock for PLL/DAC IC
19 DATA O Data for PLL/DAC IC
20 PLDL O Load enable for PLL IC
21 PLPS O Power saving for PLL IC
22 PLUL I Lock detect signal from PLL IC
23 NC O NC
24 EN4 I Encoder input 4
25 EN3 I Encoder input 3
26 EN2 I Encoder input 2
27 EN1 I Encoder input 1
28 NC O NC
29 OPTDET I 2pin option detection
30 LEDR O LED (Red) control
31 LEDG O LED (Green) control
32 SPMUT O Power switch for AF amp
33 NC O NC
34 5TC O 5T control
35 5CC O 5C control (SAVE)
36 5MSC O 5MS control
37 DACLD O Load enable for DAC IC
38 PTT I PTT key input
39 PFKEY I PF key input
40 INT I INT signal input
41 VDCSW O Voltage discharge switch
42 WID/NAR O Wide/Narrow control
43 RXD I Serial data input (FPU)
44 TXD O Serial data output (FPU)
Pin No. Signal Name I/O Function
45 NC O NC
46 NC O NC
47 VOXIN I VOX level input
48 CVDET I VCO voltage detection
49 LSDO O Low speed data output
50 HSDO O DTMF/beep output
51 BATT I Battery voltage input
52 RSSI I RSSI input
53 SQL I Squelch input
54 LSDIN I LSD input
55 THDET I Thermistor input
56 CURDET I Current detection
57 T/RSHF O VCO Shift control
58 5VC O 5V control
59 NC O NC
60 NC O NC
61 NC O NC
62 TYPE2 I Destination selection 2
63 TYPE1 I Destination selection 1
64 5RC O 5R control

TK-P701
11
COMPONENTS DESCRIPTION
Ref. No. Part Name Description
IC1 IC PLL System
IC200 IC FM IF System
IC300 IC DAC
IC301 IC LSD Buffer
IC302 IC AF Power AMP
IC303 IC AF Filter
IC304 IC MIC AMP
IC305 IC QT/DQT Filter
IC400 IC MCU
IC401 IC EEPROM
IC500 IC Voltage Detector/RESET
IC501 IC Voltage Regulator/5V
IC503 IC Voltage Regulator/5V
Q1 Transistor DC Switch
Q2 Transistor TX/RX RF Switch
Q3 Transistor Ripple filter
Q4 FET VCO
Q5 Transistor RF buffer AMP
Q6 Transistor RF AMP
Q7 Transistor Voltage regulator/3V
Q100 Transistor Pre drive AMP
Q101 FET Drive AMP
Q102 FET Final AMP
Q103 Transistor Voltage discharge switch
Q200 Transistor W/N Switch
Q201 Transistor Doubler
Q202 Transistor IF AMP
Q203 FET Mixer
Q204 FET RF AMP
Q300 Transistor DC Switch
Q301 Transistor DC Switch
Q302 FET Mute swtch
Q303 FET DC Switch
Q304 Transistor DC Switch
Q305 Transistor W/N Switch
Q306 FET Mute switch
Q400 Transistor Switch
Q401 Transistor DC Switch
Q402 Transistor DC Switch
Q500 FET DC Switch
Q501 FET DC Switch
Q502 Transistor DC Switch
D1 Diode Current steering
Ref. No. Part Name Description
D2 Variable capaci-
tance diode Frequency control/ VCO
D3 Variable capaci-
tance diode Frequency control/ VCO
D4 Diode TX/RX RF Switch
D5 Variable capaci-
tance diode Modulator /TX VCO
D6 Variable capaci-
tance diode Frequency control/ VCO
D7 Diode Ripple Filter
D100 Diode TX/RX RF Switch
D101 Diode ANT Switch
D102 Diode ANT Switch
D103 Diode ANT Switch
D200 Diode TX/RX RF Switch
D201 Variable capaci-
tance diode RX BPF Tuning
D202 Variable capaci-
tance diode RX BPF Tuning
D203 Variable capaci-
tance diode RX BPF Tuning
D204 Variable capaci-
tance diode RX BPF Tuning
D301 Diode Current steering
D400 LED LED/Green
D401 LED LED/Red
D402 Diode VCO Speed up
D500 Diode Protect
D501 Diode Current steering
TX-RX unit (X57-8093-00)

TK-P701
12
✽New Parts. indicates safety critical components.
Parts without Parts No. are not supplied.
Les articles non mentionnes dans le Parts No. ne sont pas fournis.
Teile ohne Parts No. werden nicht geliefert.
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
PARTS LIST
L: Scandinavia K: USA P: Canada
Y: PX (Far East, Hawaii) T: England E: Europe
C: China X: Australia M: Other Areas
TK-P701
TX-RX UNIT (X57-8093-00)
1 1A A02-4135-13 PLASTIC CABINET ASSY
2 3A A10-4150-41 CHASSIS
3 3B A82-0081-02 REAR PANEL
4 2B B11-1892-03 ILLUMINATION GUIDE
6 3B E04-0486-05 RF COAXIAL RECEPTACLE(SMA)
7 2A E23-1364-04 TERMINAL
8 1B E37-1539-05
PROCESSED LEAD WIRE(SP-/BRN)
9 1B E37-1540-05
PROCESSED LEAD WIRE(SP+/GRN)
10 2A E72-0436-03 TERMINAL BLOCK
11 2B F10-3186-04 SHIELDING CASE(CF200)
12 3B G01-4571-04 COIL SPRING
13 2A G11-4437-04 SHEET(Q102-SHASSIS)
14 3A G13-2364-14 CUSHION(BATT-GRAY)
15 3A G13-2366-04 CUSHION(TERMINAL)
16 2A G53-1867-13 PACKING(CHASSIS)
18 1B G53-1868-12 PACKING(TOP)
19 3B G53-1869-13 PACKING(JACK)
20 1A G53-1871-14 PACKING(MIC)
22 1B K29-9487-03 KNOB(VOL)
23 1B K29-9488-03 KNOB(SELECTOR)
24 1A K29-9489-13 KNOB(PTT)
25 1A K29-9490-13 BUTTON KNOB(SIDE)
26 3A K29-9491-03 LEVER KNOB(BATTERY)
A 2B N09-2438-05 BINDING HEAD SCREW(ANT)
B 3A N30-2606-48
PAN HEAD MACHINE SCREW(CABINET)
C 1A,2A N83-2005-48
PAN HEAD TAPTITE SCREW(X57)
28 1B T07-0787-05 SPEAKER
ACCESSORY
B09-0744-03 CAP(SP/MIC) ACCESSORY
✽
B62-2452-00 I NSTRUCTION MANUAL(E) ACCESSORY
J29-0756-05 BELT CLIP ACCESSORY
N35-3005-43
BINDING HEAD SCREW ACCESSORY
T90-1094-05
HELICAL ANTENNA ACCESSORY
✽
W08-1246-25 AC ADAPTER ACCESSORY
W08-1249-35 CHARGER ACCESSORY
✽
W09-1081-05 BATTERY ASSY ACCESSORY
X57-8090-21 TX-RX UNIT(FOR SERVICE)
D400 B30-1782-05 LED(GREEN)
D401 B30-1779-05 LED(RED)
C1 CK73GB1E154K CHIP C 0.15UF K
C2 CK73HB1A184K CHIP C 0.18UF K
C4
✽
CS77MA1A6R8M CHIP TNTL 6.8UF 10WV
C5
✽
CS77MA1ER68M CHIP TNTL 0.68UF 25WV
C6 CK73HB1A105K CHIP C 1.0UF K
C7 CC73HCH1H560G CHIP C 56PF G
C8 ,9 CK73HB1A104K CHIP C 0.10UF K
C11 CK73HB1A105K CHIP C 1.0UF K
C12 CC73HCH1H0R5B CHIP C 0.5PF B
C13 CS77MP1C010M CHIP TNTL 1UF 16WV
C14 ,15 CK73HB1C103K CHIP C 0.010UF K
C16 CK73HB1H102K CHIP C 1000PF K
C17 CC73HCH1H060B CHIP C 6.0PF B
C18 ,19 CK73HB1H102K CHIP C 1000PF K
C20 CS77MA1C100M CHIP TNTL 10UF 16WV
C21 ,22 CC73GCH1H120G CHIP C 12PF G
C23 ,24 CK73HB1H102K CHIP C 1000PF K
C25 CK73HB1C103K CHIP C 0.010UF K
C26 CK73HB1H102K CHIP C 1000PF K
C27 CC73HCH1H220J CHIP C 22PF J
C28 CK73HB1H102K CHIP C 1000PF K
C29 CC73GCH1H0R5B CHIP C 0.5PF B
C30 CK73HB1H102K CHIP C 1000PF K
C31 CK73HB1C103K CHIP C 0.010UF K
C32 CK73HB1H102K CHIP C 1000PF K
C33 CC73HCH1H470J CHIP C 47PF J
C34 CK73HB1H102K CHIP C 1000PF K
C35 CC73HCH1H150J CHIP C 15PF J
C36 CC73HCH1H120G CHIP C 12PF G
C37 CC73HCH1H150J CHIP C 15PF J
C38 CC73GCH1H220J CHIP C 22PF J
C39 CC73HCH1H120J CHIP C 12PF J
C40 ,41 CK73HB1H102K CHIP C 1000PF K
C42 CC73HCH1H150J CHIP C 15PF J
C43 CK73HB1H102K CHIP C 1000PF K
C44 CK73HB1A104K CHIP C 0.10UF K
C59 CK73HB1C333K CHIP C 0.033UF K
C100 CC73HCH1H220J CHIP C 22PF J
C101-104 CK73HB1H102K CHIP C 1000PF K
C105 CK73HB1A105K CHIP C 1.0UF K
C106 CC73HCH1H090B CHIP C 9.0PF B
C107,108 CK73HB1H102K CHIP C 1000PF K
C109 CC73HCH1H150J CHIP C 15PF J
C110 CK73HB1H102K CHIP C 1000PF K
C111 CK73HB1C103K CHIP C 0.010UF K
C112 CC73HCH1H560J CHIP C 56PF J
C113,114 CK73HB1H102K CHIP C 1000PF K
C116 CK73HB1C103K CHIP C 0.010UF K
C117 CK73FB1A225K CHIP C 2.2UF K
C119,120 CK73HB1H102K CHIP C 1000PF K
C121 CC73GCH1H330J CHIP C 33PF J
TK-P701 TX-RX UNIT (X57-8093-00)

TK-P701
13
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
TX-RX UNIT (X57-8093-00)
C122 CC73GCH1H470J CHIP C 47PF J
C123 CC73GCH1H100C CHIP C 10PF C
C124 CK73HB1H102K CHIP C 1000PF K
C125 CC73GCH1H270J CHIP C 27PF J
C126 CC73GCH1H050B CHIP C 5.0PF B
C127 CK73GB1H102K CHIP C 1000PF K
C128 CC73GCH1H060B CHIP C 6.0PF B
C129 CK73HB1H102K CHIP C 1000PF K
C130 CC73GCH1H220J CHIP C 22PF J
C131 CK73GB1H102K CHIP C 1000PF K
C132 CC73GCH1H120J CHIP C 12PF J
C134 CK73HB1H102K CHIP C 1000PF K
C135 CC73GCH1H060B CHIP C 6.0PF B
C136 CC73GCH1H270J CHIP C 27PF J
C137 CC73GCH1H060B CHIP C 6.0PF B
C138 CC73GCH1H120J CHIP C 12PF J
C139 CK73FB1A225K CHIP C 2.2UF K
C145 CK73HB1H102K CHIP C 1000PF K
C146 CC73HCH1H180J CHIP C 18PF J
C152 CK73HB1A104K CHIP C 0.10UF K
C158,159 CK73HB1H102K CHIP C 1000PF K
C200 CK73FB1A106K CHIP C 10UF K
C201 CK73HB1H102K CHIP C 1000PF K
C202 CK73HB1C103K CHIP C 0.010UF K
C203 CC73HCH1H331J CHIP C 330PF J
C204 CK73HB1E223K CHIP C 0.022UF K
C205 CK73HB1A104K CHIP C 0.10UF K
C206,207 CC73HCH1H221J CHIP C 220PF J
C208 CK73HB1A104K CHIP C 0.10UF K
C209 CC73HCH1H220J CHIP C 22PF J
C210 CK73HB1A104K CHIP C 0.10UF K
C211 CK73HB1C333K CHIP C 0.033UF K
C212,213 CK73HB1A104K CHIP C 0.10UF K
C214 CK73HB1C103K CHIP C 0.010UF K
C215 CC73HCH1H220J CHIP C 22PF J
C216 CK73HB1C103K CHIP C 0.010UF K
C217 CC73HCH1H050C CHIP C 5.0PF C
C218 CK73HB1C103K CHIP C 0.010UF K
C219 CC73HCH1H220J CHIP C 22PF J
C220 CK73HB1H102K CHIP C 1000PF K
C221 CK73HB1C103K CHIP C 0.010UF K
C222 CC73HCH1H080B CHIP C 8.0PF B
C223 CC73HCH1H060B CHIP C 6.0PF B
C224 CK73HB1C103K CHIP C 0.010UF K
C225 CC73HCH1H050C CHIP C 5.0PF C
C226 CK73HB1H102K CHIP C 1000PF K
C227 CK73HB1C103K CHIP C 0.010UF K
C228 CC73HCH1H100B CHIP C 10PF B
C230 CC73HCH1H050C CHIP C 5.0PF C
C231 CC73HCH1H220J CHIP C 22PF J
C232 CC73HCH1H030B CHIP C 3.0PF B
C234 CC73HCH1H101J CHIP C 100PF J
C235,236 CK73HB1H102K CHIP C 1000PF K
C237 CC73HCH1HR75B CHIP C 0.75PF B
C238 CC73HCH1H390G CHIP C 39PF G
C239 CK73HB1H102K CHIP C 1000PF K
C240 CC73HCH1H010B CHIP C 1.0PF B
C242 CC73HCH1H390G CHIP C 39PF G
C243 CC73HCH1H020B CHIP C 2.0PF B
C244-246 CK73HB1H102K CHIP C 1000PF K
C247 CC73HCH1H470G CHIP C 47PF G
C248 CK73HB1H102K CHIP C 1000PF K
C249 CC73HCH1H390G CHIP C 39PF G
C250 CC73HCH1H470G CHIP C 47PF G
C251 CK73HB1H102K CHIP C 1000PF K
C253 CC73HCH1H010B CHIP C 1.0PF B
C254 CC73HCH1H390G CHIP C 39PF G
C256 CK73HB1H102K CHIP C 1000PF K
C262 CK73HB1H102K CHIP C 1000PF K
C266 CC73HCH1H020B CHIP C 2.0PF B
C300,301 CK73HB1H102K CHIP C 1000PF K
C302 C92-0953-05 ELECTRO 100UF 6.3WV
C303 CK73HB1C473K CHIP C 0.047UF K
C304 CK73FB1A106K CHIP C 10UF K
C305 CK73HB1C103K CHIP C 0.010UF K
C306 CK73HB1A224K CHIP C 0.22UF K
C308 CK73GB1E105K CHIP C 1.0UF K
C309 CK73HB1A104K CHIP C 0.10UF K
C310 CK73HB1C473K CHIP C 0.047UF K
C311 CK73HB1A105K CHIP C 1.0UF K
C312 CK73HB1C473K CHIP C 0.047UF K
C313 CK73HB1A104K CHIP C 0.10UF K
C314 CC73HCH1H101J CHIP C 100PF J
C315 CK73FB1A106K CHIP C 10UF K
C316 CK73HB1A104K CHIP C 0.10UF K
C317 CK73HB1C103K CHIP C 0.010UF K
C318 CC73HCH1H221J CHIP C 220PF J
C319 CK73HB1C103K CHIP C 0.010UF K
C320 CK73GB1E104K CHIP C 0.10UF K
C321 CK73HB1C103K CHIP C 0.010UF K
C322 CK73HB1H102K CHIP C 1000PF K
C323 CK73HB1A104K CHIP C 0.10UF K
C324 CK73HB1A184K CHIP C 0.18UF K
C325 CK73HB1E153K CHIP C 0.015UF K
C326 CK73HB1H822K CHIP C 8200PF K
C328 CK73HB1A184K CHIP C 0.18UF K
C329 CK73HB1C333K CHIP C 0.033UF K
C330 CK73HB1H561K CHIP C 560PF K
C332 CK73HB1C103K CHIP C 0.010UF K
C333 CK73HB1H102K CHIP C 1000PF K
C334,335 CK73HB1A184K CHIP C 0.18UF K
C336 CK73HB1C103K CHIP C 0.010UF K
C337 CK73HB1A184K CHIP C 0.18UF K
C338 CC73HCH1H331J CHIP C 330PF J
C339 CK73HB1A104K CHIP C 0.10UF K
C340 CC73HCH1H100B CHIP C 10PF B
C341 CK73HB1H332K CHIP C 3300PF K
C342 CK73HB1C103K CHIP C 0.010UF K
C343 CK73HB1A184K CHIP C 0.18UF K
C344 CK73HB1C273K CHIP C 0.027UF K
C345 CK73HB1H102K CHIP C 1000PF K
C346 CK73HB1A184K CHIP C 0.18UF K
C347 CK73GB1A105K CHIP C 1.0UF K
C349 CK73HB1C473K CHIP C 0.047UF K
C350 CK73HB1H102K CHIP C 1000PF K
C352 CK73HB1H102K CHIP C 1000PF K
C353 CK73GB1E105K CHIP C 1.0UF K
C354 CK73HB1A224K CHIP C 0.22UF K
C355 CK73HB1A105K CHIP C 1.0UF K
C357,358 CK73HB1A104K CHIP C 0.10UF K

TK-P701
14
Ref. No. Address Parts No. Description Desti-
nation
New
parts
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
TX-RX UNIT (X57-8093-00)
C360 CK73HB1A104K CHIP C 0.10UF K
C397 CK73HB1H102K CHIP C 1000PF K
C400 CK73HB1A104K CHIP C 0.10UF K
C401 CK73HB1H102K CHIP C 1000PF K
C402 CC73HCH1H120J CHIP C 12PF J
C403 CC73HCH1H010B CHIP C 1.0PF B
C404 CK73HB1A104K CHIP C 0.10UF K
C405 CK73HB1H102K CHIP C 1000PF K
C406 CC73HCH1H120J CHIP C 12PF J
C407 CK73HB1H102K CHIP C 1000PF K
C408 CK73HB1C103K CHIP C 0.010UF K
C409 CK73HB1H102K CHIP C 1000PF K
C411-415 CK73HB1H102K CHIP C 1000PF K
C500 CC73HCH1H101J CHIP C 100PF J
C501,502 CK73HB1H102K CHIP C 1000PF K
C503 CK73FB1A475K CHIP C 4.7UF K
C504 CK73HB1H102K CHIP C 1000PF K
C505 CK73GB1E105K CHIP C 1.0UF K
C506 CK73HB1H102K CHIP C 1000PF K
C507 CK73FB1A106K CHIP C 10UF K
C511 CK73HB1H102K CHIP C 1000PF K
C513,514 CK73GB1E105K CHIP C 1.0UF K
C515,516 CK73HB1H102K CHIP C 1000PF K
C517 CK73FB1A475K CHIP C 4.7UF K
C522-524 CK73HB1H102K CHIP C 1000PF K
J300 2B E11-0484-05 3.5D PHONE JACK(3.5D/MIC)
J301 2B E11-0717-05 2.5D PHONE JACK(2.5D/SP)
F101 F53-0287-05 FUSE(0.5A)
F300 F53-0467-05 FUSE(0.315A)
F500 F53-0372-05 FUSE(3.15A)
101 2A J30-1308-04 SPACER(MIC300)
CF200 2A L72-1046-05 CERAMIC FILTER(450KHZ)
CD200 2A L79-1914-05 CERAMIC DISCRIMINATOR
L1 L40-4791-86
SMALL FIXED INDUCTOR(4.7UH)
L2 L41-1885-45
SMALL FIXED INDUCTOR(180NH)
L3 ,4 L41-2278-14
SMALL FIXED INDUCTOR(22NH)
L5 ,6 L40-1001-86
SMALL FIXED INDUCTOR(10UH)
L7 L40-1285-71
SMALL FIXED INDUCTOR(120NH)
L8 L40-2775-71
SMALL FIXED INDUCTOR(27NH)
L9 L40-8275-71
SMALL FIXED INDUCTOR(82NH)
L100 L40-6875-71
SMALL FIXED INDUCTOR(68NH)
L101 L40-1085-71
SMALL FIXED INDUCTOR(100NH)
L102 L40-3375-71
SMALL FIXED INDUCTOR(33NH)
L103 L41-8275-53
SMALL FIXED INDUCTOR(82NH)
L104 L34-4577-05 AIR-CORE COIL(9T)
L105 L34-4571-05 AIR-CORE COIL(3T)
L106,107 L34-4573-05 AIR-CORE COIL(5T)
L108 L34-4574-05 AIR-CORE COIL(6T)
L109 L41-2295-52
SMALL FIXED INDUCTOR(2.2UH)
L110-112 L34-4577-05 AIR-CORE COIL(9T)
L203 L40-2763-71
SMALL FIXED INDUCTOR(2.7NH)
L204 L41-8285-14
SMALL FIXED INDUCTOR(820N)
L205 L40-2275-71
SMALL FIXED INDUCTOR(22NH)
L206 L40-1285-71
SMALL FIXED INDUCTOR(120NH)
L207,208 L41-8278-14
SMALL FIXED INDUCTOR(82NH)
L209 L41-6878-14
SMALL FIXED INDUCTOR(68NH )
L210 L41-1878-14
SMALL FIXED INDUCTOR(18NH)
L211 L40-5681-86
SMALL FIXED INDUCTOR(0.56UH)
L212 L40-8281-86
SMALL FIXED INDUCTOR(0.82UH)
L213 L40-5681-86
SMALL FIXED INDUCTOR(0.56UH)
L215 L41-8278-14 SMALL FIXED INDUCTOR(82NH)
X1 L77-3074-05 TCXO(19.2 MHZ)
X400 L77-2974-05
CRYSTAL RESONATOR(11.0592MHZ)
XF200 L71-0669-05 MCF(38.85MHZ)
R1 RK73HB1J105J CHIP R 1.0M J 1/16W
R2 RK73HB1J103J CHIP R 10K J 1/16W
R3 RK73HB1J222J CHIP R 2.2K J 1/16W
R5 RK73HB1J821J CHIP R 820 J 1/16W
R9 RK73HB1J103J CHIP R 10K J 1/16W
R11 RK73HB1J272J CHIP R 2.7K J 1/16W
R12 RK73HB1J104J CHIP R 100K J 1/16W
R13 RK73HB1J681J CHIP R 680 J 1/16W
R14 RK73HB1J103J CHIP R 10K J 1/16W
R15 RK73HB1J104J CHIP R 100K J 1/16W
R16 -22 RK73HB1J103J CHIP R 10K J 1/16W
R23 RK73HB1J104J CHIP R 100K J 1/16W
R25 RK73HB1J100J CHIP R 10 J 1/16W
R26 RK73HB1J392J CHIP R 3.9K J 1/16W
R27 RK73HB1J181J CHIP R 180 J 1/16W
R28 RK73HB1J560J CHIP R 56 J 1/16W
R29 RK73HB1J472J CHIP R 4.7K J 1/16W
R30 RK73HB1J221J CHIP R 220 J 1/16W
R32 RK73HB1J102J CHIP R 1.0K J 1/16W
R33 RK73HB1J473J CHIP R 47K J 1/16W
R34 RK73HB1J100J CHIP R 10 J 1/16W
R37 RK73HB1J562J CHIP R 5.6K J 1/16W
R38 RK73HB1J332J CHIP R 3.3K J 1/16W
R39 RK73HB1J331J CHIP R 330 J 1/16W
R40 RK73HB1J332J CHIP R 3.3K J 1/16W
R41 RK73HB1J100J CHIP R 10 J 1/16W
R42 RK73HB1J332J CHIP R 3.3K J 1/16W
R43 RK73HB1J103J CHIP R 10K J 1/16W
R44 RK73FB2B000J CHIP R 0 J 1/8W
R45 RK73HB1J000J CHIP R 0 J 1/16W
R50 RK73HB1J104J CHIP R 100K J 1/16W
R51 RK73HB1J333J CHIP R 33K J 1/16W
R52 RK73HB1J102J CHIP R 1.0K J 1/16W
R100 RK73HB1J472J CHIP R 4.7K J 1/16W
R101 RK73HB1J102J CHIP R 1.0K J 1/16W
R102 RK73HB1J222J CHIP R 2.2K J 1/16W
R103 RK73HB1J180J CHIP R 18 J 1/16W
R104 RK73HB1J331J CHIP R 330 J 1/16W
R105 RK73HB1J180J CHIP R 18 J 1/16W
R106 RK73HB1J104J CHIP R 100K J 1/16W
R107 RK73HB1J100J CHIP R 10 J 1/16W
R108 RK73HB1J823J CHIP R 82K J 1/16W
R109 RK73HB1J470J CHIP R 47 J 1/16W
R111 RK73HB1J683J CHIP R 68K J 1/16W
R112 RK73HB1J470J CHIP R 47 J 1/16W
R113 RK73HB1J563J CHIP R 56K J 1/16W
R114 RK73GB2A000J CHIP R 0 J 1/10W
R115 RK73FB2B000J CHIP R 0 J 1/8W
R116 RK73HB1J393J CHIP R 39K J 1/16W
R117 RK73HB1J271J CHIP R 270 J 1/16W
R119 RK73HB1J271J CHIP R 270 J 1/16W
R120 RK73HB1J331J CHIP R 330 J 1/16W
R121-123 RK73EB2ER39K CHIP R 0.39 K 1/4W
If a part reference number is listed in a shaded box, that part does not come with the PCB.

TK-P701
15
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
Ref. No. Address Parts No. Description Desti-
nation
New
parts
TX-RX UNIT (X57-8093-00)
R136 RK73HB1J182J CHIP R 1.8K J 1/16W
R139 RK73GB2A000J CHIP R 0 J 1/10W
R155 RK73HB1J180J CHIP R 18 J 1/16W
R200 RK73HB1J103J CHIP R 10K J 1/16W
R201 RK73HB1J470J CHIP R 47 J 1/16W
R202 RK73HB1J392J CHIP R 3.9K J 1/16W
R203 RK73HB1J333J CHIP R 33K J 1/16W
R204 RK73HB1J271J CHIP R 270 J 1/16W
R205 RK73HB1J682J CHIP R 6.8K J 1/16W
R206 RK73HB1J224J CHIP R 220K J 1/16W
R207 RK73HB1J562J CHIP R 5.6K J 1/16W
R208 RK73HB1J101J CHIP R 100 J 1/16W
R209 RK73HB1J470J CHIP R 47 J 1/16W
R210 RK73HB1J334J CHIP R 330K J 1/16W
R211 RK73HB1J272J CHIP R 2.7K J 1/16W
R212 RK73HB1J184J CHIP R 180K J 1/16W
R213 RK73HB1J102J CHIP R 1.0K J 1/16W
R214 RK73HB1J681J CHIP R 680 J 1/16W
R215 RK73HB1J331J CHIP R 330 J 1/16W
R216 RK73HB1J470J CHIP R 47 J 1/16W
R217 RK73FB2B000J CHIP R 0 J 1/8W
R218 RK73HB1J102J CHIP R 1.0K J 1/16W
R219 RK73HB1J332J CHIP R 3.3K J 1/16W
R220 RK73HB1J331J CHIP R 330 J 1/16W
R221 RK73HB1J823J CHIP R 82K J 1/16W
R222 RK73HB1J104J CHIP R 100K J 1/16W
R223,224 RK73HB1J823J CHIP R 82K J 1/16W
R225 RK73HB1J000J CHIP R 0 J 1/16W
R226,227 RK73HB1J105J CHIP R 1.0M J 1/16W
R228 RK73HB1J470J CHIP R 47 J 1/16W
R229 RK73HB1J152J CHIP R 1.5K J 1/16W
R230 RK73HB1J820J CHIP R 82 J 1/16W
R231 RK73HB1J471J CHIP R 470 J 1/16W
R232,233 RK73HB1J104J CHIP R 100K J 1/16W
R234 RK73HB1J184J CHIP R 180K J 1/16W
R236,237 RK73HB1J105J CHIP R 1.0M J 1/16W
R260 RK73HB1J273J CHIP R 27K J 1/16W
R264 RK73HB1J394J CHIP R 390K J 1/16W
R267,268 RK73HB1J000J CHIP R 0 J 1/16W
R300 RK73HB1J152J CHIP R 1.5K J 1/16W
R301 RK73HB1J101J CHIP R 100 J 1/16W
R302 RK73HB1J102J CHIP R 1.0K J 1/16W
R303 RK73HB1J471J CHIP R 470 J 1/16W
R304 RK73HB1J473J CHIP R 47K J 1/16W
R305-308 RK73HB1J102J CHIP R 1.0K J 1/16W
R309 RK73HB1J182J CHIP R 1.8K J 1/16W
R310,311 RK73HB1J102J CHIP R 1.0K J 1/16W
R312 RK73HB1J222J CHIP R 2.2K J 1/16W
R313-315 RK73HB1J103J CHIP R 10K J 1/16W
R316 RK73HB1J000J CHIP R 0 J 1/16W
R317 RK73HB1J334J CHIP R 330K J 1/16W
R318 RK73HB1J274J CHIP R 270K J 1/16W
R321 RK73HB1J474J CHIP R 470K J 1/16W
R322 RK73HB1J105J CHIP R 1.0M J 1/16W
R323 RK73HB1J562J CHIP R 5.6K J 1/16W
R324,325 RK73HH1J473D CHIP R 47K D 1/16W
R326 RK73HB1J000J CHIP R 0 J 1/16W
R327 RK73HB1J824J CHIP R 820K J 1/16W
R328 RK73HB1J684J CHIP R 680K J 1/16W
R329,330 RK73HB1J103J CHIP R 10K J 1/16W
R331 RK73HB1J473J CHIP R 47K J 1/16W
R332 RK73HB1J272J CHIP R 2.7K J 1/16W
R334 RK73HB1J103J CHIP R 10K J 1/16W
R335 RK73HB1J000J CHIP R 0 J 1/16W
R336 RK73HB1J473J CHIP R 47K J 1/16W
R337 RK73HB1J000J CHIP R 0 J 1/16W
R340 RK73HB1J103J CHIP R 10K J 1/16W
R342 RK73HB1J153J CHIP R 15K J 1/16W
R344 RK73HB1J103J CHIP R 10K J 1/16W
R345 RK73HB1J561J CHIP R 560 J 1/16W
R347 RK73HB1J103J CHIP R 10K J 1/16W
R348 RK73HB1J183J CHIP R 18K J 1/16W
R350 RK73HB1J471J CHIP R 470 J 1/16W
R351 RK73HB1J561J CHIP R 560 J 1/16W
R352 RK73HB1J104J CHIP R 100K J 1/16W
R353 RK73HB1J102J CHIP R 1.0K J 1/16W
R354 RK73HB1J334J CHIP R 330K J 1/16W
R355 RK73HB1J473J CHIP R 47K J 1/16W
R356 RK73HB1J183J CHIP R 18K J 1/16W
R357 RK73HB1J564J CHIP R 560K J 1/16W
R358 RK73HB1J473J CHIP R 47K J 1/16W
R360 RK73HB1J184J CHIP R 180K J 1/16W
R361 RK73HB1J561J CHIP R 560 J 1/16W
R363 RK73HB1J562J CHIP R 5.6K J 1/16W
R364 RK73HB1J471J CHIP R 470 J 1/16W
R365 RK73HB1J000J CHIP R 0 J 1/16W
R366 RK73HB1J104J CHIP R 100K J 1/16W
R367 RK73HB1J473J CHIP R 47K J 1/16W
R369 RK73HB1J103J CHIP R 10K J 1/16W
R370 RK73HH1J473D CHIP R 47K D 1/16W
R371 RK73HB1J822J CHIP R 8.2K J 1/16W
R372 RK73HH1J473D CHIP R 47K D 1/16W
R373 RK73HB1J000J CHIP R 0 J 1/16W
R374 RK73HH1J473D CHIP R 47K D 1/16W
R375 RK73HB1J103J CHIP R 10K J 1/16W
R376 RK73HH1J473D CHIP R 47K D 1/16W
R377 RK73HB1J393J CHIP R 39K J 1/16W
R378 RK73HB1J102J CHIP R 1.0K J 1/16W
R379 RK73HB1J104J CHIP R 100K J 1/16W
R386 RK73HB1J392J CHIP R 3.9K J 1/16W
R388 RK73HB1J822J CHIP R 8.2K J 1/16W
R389 RK73HB1J102J CHIP R 1.0K J 1/16W
R390 RK73HB1J000J CHIP R 0 J 1/16W
R392,393 RK73HB1J102J CHIP R 1.0K J 1/16W
R394 RK73HB1J000J CHIP R 0 J 1/16W
R396 RK73HB1J000J CHIP R 0 J 1/16W
R400 RK73HB1J472J CHIP R 4.7K J 1/16W
R401 RK73HB1J102J CHIP R 1.0K J 1/16W
R406 RK73HB1J101J CHIP R 100 J 1/16W
R407 RK73HB1J473J CHIP R 47K J 1/16W
R408 RK73HB1J101J CHIP R 100 J 1/16W
R409,410 RK73GB2A221J CHIP R 220 J 1/10W
R411,412 RK73HB1J472J CHIP R 4.7K J 1/16W
R413 RK73HB1J102J CHIP R 1.0K J 1/16W
R414 RK73HB1J474J CHIP R 470K J 1/16W
R433 RK73HB1J000J CHIP R 0 J 1/16W
R438 RK73HB1J473J CHIP R 47K J 1/16W
R455 RK73HB1J562J CHIP R 5.6K J 1/16W
R473 RK73HB1J000J CHIP R 0 J 1/16W
R502 RK73HB1J334J CHIP R 330K J 1/16W

TK-P701
16
Ref. No. Address Parts No. Description Desti-
nation
New
parts
PARTS LIST
Ref. No. Address Parts No. Description Desti-
nation
New
parts
TX-RX UNIT (X57-8093-00)
R505 RK73HB1J473J CHIP R 47K J 1/16W
R508 RK73HB1J473J CHIP R 47K J 1/16W
R509 RK73HB1J104J CHIP R 100K J 1/16W
R511 RK73HB1J334J CHIP R 330K J 1/16W
R512 RK73GB2A271J CHIP R 270 J 1/10W
VR500 2B R31-0684-05 VARIABLE RESISTOR
S400 2B S70-0414-05 TACT SWITCH(PTT)
S401 S70-0514-05 TACT SWITCH(SIDE)
S402 2B S60-0447-05 ROTARY SWITCH(SELECTOR)
MIC300 2A T91-0674-05 MIC ELEMENT
D1 DA2S101 DIODE
D2 ,3 1SV325F VARIABLE CAPACITANCE DIODE
D4 HSC277 DIODE
D5 ,6 HVC350B VARIABLE CAPACITANCE DIODE
D7 DA2S101 DIODE
D100 HSC277 DIODE
D101,102 HVC131 DIODE
D200 HSC277 DIODE
D201-204 HVC350B VARIABLE CAPACITANCE DIODE
D301 KDR731 DIODE
D380 DZ2S068(M) ZENER DIODE
D402 DA2S101 DIODE
D500 GN1G DIODE
D501 KDR720E-P DIODE
IC1 MB15E03SL-E1 MOS-IC
IC200 NJM2591V BI-POLAR IC
IC300 R2A20178NP DAC
IC301 NJM12904RB1 MOS-IC
IC302 TA7368PL MOS-IC
IC303-305 NJM12904RB1 MOS-IC
IC400 F2136ACNKDRB MCU
IC401 EX24016ATAS0A ROM IC
IC500 XC6120N302N-G MOS-IC
IC501 XC6209B502P-G MOS-IC
IC503 XC6209B502P-G MOS-IC
Q1 RT1N141U-T111 TRANSISTOR
Q2 RT1N436U-T111 TRANSISTOR
Q3 2SC5383-T111 TRANSISTOR
Q4 MCH3914(7)-H FET
Q5 2SC5488A-H TRANSISTOR
Q6 2SC5636 TRANSISTOR
Q7 2SC5383-T111 TRANSISTOR
Q100 2SC4926YD TRANSISTOR
Q101 RFM01U7P FET
Q102 RD07MUS2BT112 FET
Q103 RT1N141U-T111 TRANSISTOR
Q200 RT1P237U-T111 TRANSISTOR
Q201,202 KTC4080E-P TRANSISTOR
Q203,204 3SK318 FET
Q300,301 RT1N441U-T111 TRANSISTOR
Q302 2SK3577-A FET
Q303 SSM6J08FU(F) FET
Q304 RT1P237U-T111 TRANSISTOR
Q305 RT1N144U-T111 TRANSISTOR
Q306 2SK3577-A FET
Q400 2SC4919-S TRANSISTOR
Q401,402 RT1N144U-T111 TRANSISTOR
Q500 MCH3309-H FET
Q501 SSM3J05FU-F FET
Q502 RT1P237U-T111 TRANSISTOR
TH100 B57331V2104J THERMISTOR(100K)
If a part reference number is listed in a shaded box, that part does not come with the PCB.

TK-P701
17
EXPLODED VIEW
Parts with the exploded numbers larger than 700 are not supplied.
3
2
1
BA
11
23
22
24
25
28
18
9
8
1
20
Cx13
TX-RX unit 13
16
B
26 12
3
15
19
6
A
7
10
VR500
S402
4
700
701
J300
J301
2
A : N09-2438-05
B : N30-2606-48
C : N83-2005-48
101
MIC300
CF200
CD200
S400
B
14
A
If a part reference number is listed in a box on the exploded view of the PCB, that part does not come with the PCB.
These parts must be ordered separately.

TK-P701
18
ADJUSTMENT
Test Equipment Required for Alignment
Test Equipment Major Specifications
1. Standard Signal Generator (SSG) Frequency Range 136 to 174MHz Modulation Frequency modulation and external modulation
Output –127dBm/0.1µV to greater than –47dBm/1mV
2. RF Power Meter Input Impedance 50Ω Operation Frequency 136 to 174MHz
Measurement Range Vicinity of 10W
3. Deviation Meter Frequency Range 136 to 174MHz
4. DigitalVolt Meter (DVM) Measuring Range 10mV to 10V DC
Input Impedance High input impedance for minimum circuit loading
5. Oscilloscope DC through 30MHz
6. High Sensitivity
Frequency Counter Frequency Range 10Hz to 1000MHz Frequency Stability 0.2ppm or less
7. DC Ammeter 5A
8. AF Volt Meter (AF VM) Frequency Range 50Hz to 10kHz
Voltage Range 1mV to 10V
9. Audio Generator (AG) Frequency Range 50Hz to 5kHz or more
Output 0 to 1V
10. Distortion Meter Capability 3% or less at 1kHz
Input Level 50mV to 10Vrms
11. Spectrum Analyzer Measuring Range 10kHz to 1GHz or more
12. Tracking Generator Center frequency 50kHz to 600MHz
Output Voltage 100mV or more
13. 8ΩDummy Load Approx. 8Ω, 3W
14. Regulated Power Supply 5V to 10V, approx.3A
Useful if ammeter equipped
■Antenna connector adapter
The antenna connector of this transceiver uses an SMA
terminal.
Use an antenna connector adapter [SMA(f) – BNC(f) or
SMA(f) – N(f)] for adjustment. (The adapter is not provided
as an option, so buy a commercially-available one.)
BATT+ (7.5V)
BATT– (GND)
–+
■DC Supply
BATT+, BATT– : External power supply terminal (Fasten
it with an alligator clip.)

TK-P701
19
ADJUSTMENT
Frequency and Signaling
The transceiver has been adjusted for the frequencies
shown in the following table. When required, re-adjust them
following the adjustment procedure to obtain the frequencies
you want in actual operation.
■Test Frequency (MHz)
CH RX Frequency TX Frequency
1 155.05000 155.10000
2 136.05000 136.10000
3 173.95000 173.90000
4 155.00000 155.00000
5 155.20000 155.20000
6 155.40000 155.40000
7~16 - -
■Signaling
No. RX (Decode) TX (Encode)
1 None None
2 None 100Hz Square Wave
3 QT 67.0Hz QT 67.0Hz
4 QT 151.4Hz QT 151.4Hz
5 QT 210.7Hz QT 210.7Hz
6 QT 254.1Hz QT 254.1Hz
7 DQT D023N DQT D023N
8 DQT D754I DQT D754I
9 None DTMF
(Code: 159D)
10 None DTMF
(Code: 9)
Preparations forTuning theTransceiver
Before attempting to tune the transceiver, connect the
unit to a suitable power supply.
Whenever the transmitter is tuned, the unit must be con-
nected to a suitable dummy load (i.e.power meter).
The speaker output connector must be terminated with a
8Ωdummy load and connected to an AC voltmeter and an
audio distortion meter or a SINAD measurement meter at all
times during tuning.
■Adjustment frequency (MHz)
Tuning point RX TX
Low 136.05000 136.10000
Center 155.05000 155.10000
High 173.95000 173.90000
Adjustment Points
TX-RX UNIT
Component side view
Note: When replacing CF200, apply bond to
the point shown in the figure.
Foil side view
ANT
MIC300
CF200 IC400
CD200
+
‒
BATT+
BATT–
CV
CV: VCO Lock Voltage
S401
Side KEY
S400
PTT
J301
SP J300
MIC

TK-P701
20
ADJUSTMENT
Common Section
Item Condition Measurement Adjustment Specifications / Remarks
Test-
equipment
Unit Terminal Unit Parts Method
1. Setting 1)BATT terminal voltage: 7.5V
2)SSG standard modulation
[Wide]
MOD: 1kHz, DEV: 3kHz
[Narrow]
MOD: 1kHz, DEV: 1.5kHz
2. VCO Lock
Voltage 1) Adj item: High Power meter TX-RX ANT
(CV)
FPU 4.1V ±0.1V
Transmitter Section
Item Condition Measurement Adjustment Specifications / Remarks
Test-
equipment
Unit Terminal Unit Parts Method
1. Frequency 1)Adj item: High
Press [Transmit] button. f. counter TX-RX ANT FPU 173.900MHz ±50Hz
2. High
Transmit
Power and
Protective
Current
*Note
1)Adj item: Low, Center, High
(3 points)
BATT terminal voltage: 7.5V
Press [Transmit] button.
Power
meter
Ammeter
FPU 4.8W ±0.1W
2.0A or less
3. Low
Transmit
Power
1)Adj item: Low, Center, High
(3 points)
BATT terminal voltage: 7.5V
Press [Transmit] button.
1.0W ±0.1W
1.0A or less
4. DQT
Balance
[Wide]
1)Adj item: Low, Center, High
(3 points)
(Signaling Square Wave)
Deviation meter filter
LPF: 3kHz
HPF: OFF
Press [Transmit] button.
Power
meter
Deviation
meter
Oscilloscope
AG
AF VM
TX-RX ANT
SP/MIC
connector
FPU Make the modulation
wave into square
waves.
5. Maximum
Deviation
[Wide]
1)Adj item: Center, Low, High
(3 points)
AG: 1kHz/150mV
Deviation meter filter
LPF: 15kHz
HPF: OFF
Press [Transmit] button.
4.0kHz
(According to
the lager +, –)
±100Hz
6. Battery
Warning
Level
1)BATT terminal voltage: 5.9V DVM TX-RX BATT
terminal
FPU Write BATT terminal voltage: 5.9V
7. Battery
Detection
Check
(User mode)
1)BATT terminal voltage: 5.7V
PTT: ON Power meter
DVM
ANT
BATT
terminal
Check LED blinks
No transmit power
2)BATT terminal voltage: 7.5V
PTT: ON LED does not blink
• It is not necessary to adjust the fixed values for the DTMF-DEV, DQT-DEV, QT-DEV, and MIC sensitivity.
• The TX-DEV Narrow setting uses the Wide calculated adjustment level value.
*Note: Please do not adjust High Transmit power without connecting TX Power meter or 50 ohm dummy load to the ANT terminal.