Kessil A360X Tuna Blue User manual

A360X x 1
AC Adapter Cable (6 feet) x 1
DC Power Extension Cable (6 feet) x 1
Power Adapter x 1
Hanging Bracket x 2 Hanging Ring x 1
Screw Hook x 2
Inside the Box Parts Diagram Safety Instructions
Instructions de Securite
A
G
H
B E
I
Power Cord
Intensity Tuning Knob
Screw Hook
Hanging Ring
Hanging Bracket
Color Tuning Knob
K-Link
Venting Holes
Lens
A
B
C
D
E
F
G
H
I
1. DO NOT use a power adapter that is out of the
specifications. This is a fire hazard and may
lead to unit failure.
2. DO NOT use outdoors. This unit is intended for
indoor use only.
3. DO NOT expose unit to an extremely humid
environment or submerse unit in water. This may
lead to unit failure.
4. DO NOT place working illuminator in close
contact with any objects. This may cause
objects to heat up and the unit to overheat.
5. KEEP Lens (I) away from sharp objects. Sharp
objects may break the lens and lead to unit
failure.
6. DO NOT cover or place objects on the power
adapter. Power adapter should not be contained
in an airtight space.
1. N'utilisez PAS une source d'alimentation qui est en
dehors des spécifications. Ceci constitue un risque
d'incendie et peut entraîner une défaillance de
l'unité.
2. NE PAS utiliser à l'extérieur. Cette unité est
destinée à une utilisation en intérieur uniquement.
3. NE PAS exposer l'appareil à un environnement
extrêmement humide ou immerger l'appareil dans
l'eau. Cela peut entraîner une défaillance de
l'unité.
4. NE placez PAS l'illuminateur de travail en contact
étroit avec des objets. Cela peut provoquer un
échauffement des objets et une surchauffe de
l'appareil.
5. GARDEZ l'objectif (I) à l'écart des objets pointus.
Des objets pointus peuvent casser l'objectif et
entraîner une défaillance de l'unité.
6. NE PAS couvrir ou placer d'objets sur
l'alimentation électrique. L'alimentation ne doit pas
être contenue dans un espace étanche à l'air.
C D F
A 360
LED Aquarium Light
Tuna Blue Tuna Sun
210914A5

Power Consumption
Input Voltage
Illuminator
19 VDC
Getting Started Maintenance
Troubleshooting Guide
Product Specification
Step 1 Power Step 3 Controlling Multiple A360X
Step 4 Mounting
Step 2 Control
Connect the A360X to the power adapter and
plug it into a wall outlet. Turn the Intensity Tuning
Knob (B) to the right to turn on the light.
• Turn the Intensity Tuning Knob (B) to adjust the
brightness of the fixture.
• Turn the Color Tuning Knob (F) to adjust the light
to the desired color.
• A360X can be connected and controlled through
Kessil Spectral Controller X with a Type-C USB
Cable (K-Link Cable).
•Connect two or more lights with K-Link Cables
as shown in the image.
• Multiple A360X lights can be controlled by either
a single external controller or manually.
•When controlling without an external controller,
tuning controls on any light control all other
lights in chain.
• Screw the Hanging Ring (D) into the
center screw hole.
• Hang the light with the two
Screw Hooks (C) and the two
Hanging Brackets (E).
• To install the Hanging
Brackets (E), remove the
screws on the A360X, use
the same screws to secure
the fasteners with triangular
rings onto the light fixture.
Problem
Make sure the unit is connected to the power adapter and the power
adapter is plugged into an outlet with the correct specifications.
Make sure the power adapter has the right specifications.
Make sure the unit has not overheated by operating at a room
temperature above 100°F/40°C.
Make sure electrical power is available to the AC outlet being used.
Make sure the power adapter has the right specifications.
Make sure the device is operating within the specified operating
temperature range. If unit overheats, it will automatically shut down.
Make sure the fan is operating properly.
Cause / Solution
1.Keep the air intake holes, Venting Holes (H), and fan clear of dust. To clean the fan, unplug the unit and
insert the tip of a CO2 dust blower (or similar dust blower) in one of the Venting Holes (H) on the unit's
outer shell. Hold and spray. You can also gently vacuum out the light through the venting holes.
2.Keep the Lens (I) clean. If the lens becomes contaminated with water, dust, or other particles, unplug
the unit and clean the lens with isopropyl alcohol. Wet a cotton swab or a napkin in isopropyl alcohol,
gently wipe the surface of the lens, and let it dry.
3.Keep plastic covers for K-Link ports plugged in when the ports are not in use. Keep the ports clean all
the time.
Please make sure to perform maintenance before doing any troubeshooting.
Light doesn’t turn ON
Unit is flickering
90W MAX Input
Output
Listed Power Adapter
19 VDC, 4.74A
100-240 VAC, 47-63 Hz, 1.5 A MAX
Kessil Lighting
A DiCon Brand
1689 Regatta Blvd, Richmond, CA 94804
[phone]
www.kessil.com
(Controller X not included)
This is a LED light source emitting 40 % or more of total radiation
power of the range 250-800 nm in the range of 400-480 nm, and
intended for coral growth.
@kessilled
@kessil
kessil.com
kessil.led
kessiltube