Kett Pearlest User manual

Accessories
Part names Preparation
Features
Polishing Procedure
Others
●Open/close of the lever is linked with the motor
When the lever is pushed, the polished sample will be
ejected to the polished sample receptacle.
●Sample scatter-proof function
To avoid scattering of the sample, the polishing disk will
not be rotated if the cover is fully opened.
●Transparent bran receptacle
The timing for discarding the removed bran can be seen
at a glance.
●Motor overload prevention
If excessive force is applied to the motor and there is a
risk of the motor coil being damaged, the power turns off
automatically.
①Properly attach the bran receptacle to the main unit.
Fully insert the bran receptacle to the outlet of the
removed bran. Note that if the case is not properly
attached, the bran will be scattered during polishing.
①Take a spoonful of sample with the supplied spoon.
* A spoonful of rice measured with the supplied spoon is approxi-
mately 10 g.
②Set the sample on the polishing disk of the
Pearlest and close the cover. Then, lock the latch.
* If bran or dust is left, the cover may not be closed. Before start
polishing, clean the unit and fully close the cover.
③Turn the power ON to start polishing.
The polishing time differs depending on the samples or moisture
content. Set the polishing time referring to the following.
Samples A guide for polishing time
Short rice 30 to 40 sec.
Long rice 40 to 60 sec.
Barley 180 to 240 sec.
* Many broken particles may be generated depending on the sample.
* For barley, optional parts for barley polishing are required. Before
polishing, refer to the back page and assemble the parts correctly.
④Push the lever while the cover is closed.
* If the sample is left in the polishing unit, the clatter may be heard.
Push the lever until the sound is stopped.
⑤The polished sample is ejected to the polished
sample receptacle.
⑥The motor stop when the power is turned off.
⑦Open the cover, and take out the polished sample
receptacle.
* The polished sample receptacle can be used as a strainer. If bran
or dust is left on the tray, clean the tray before use.
Pallet
(TP-3000-A-01)
Brush
(TP-3000-A-02)
AC adapter
(TP-3000-A-05)
Accessory case
(TP-3000-A-06)
Paint brush
(TP-3000-A-03)
Spoon
(Rice : approx. 10 g/spoon)
(TP-3000-A-04)
<Cleaning>
After a few times of polishing, removed bran or dust may
accumulate around the rubber disc or polishing disk.
Clean the polishing unit using the pallet or paint brush.
<Storage>
When storing the instrument, remove the polishing disk,
rubber ring, and rubber disc.
Clean the inside of the bran receptacle. Store the
instrument in a place where the direct sunlight is avoided
under dry conditions.
<Specications>
Power
Input: 100-240 V AC (50/60Hz), 1.4 A MAX
Output: 24 V DC, 2.71 A
Dimensions: 110 (W) x 152 (D) x 176 (H)
Mass: approximately 1.7 kg
Compact Grain Polisher Pearlest
TP-3000
Operating Manual
Thank you for purchasing our grain polisher.
The Compact Grain Polisher Pearlest can polish a
small amount of rice extracted for the purpose of
testing in a short time. Since the rubber plate is used,
capability of bran removal is excellent, and the grains
are well nished. The polished grains can be ejected
only by pushing the motor-linked lever. The Pearlest
can also be used for inspecting condition and mixing
degree of spotted rice inuenced by pentatomid,
burnt, cracked, colored, nonglutinous, or glutinous
rice. Before using this instrument, thoroughly read
this operating manual, and use it properly.
Bran receptacle
(TP-3000-R-04)
Power switch
Cover
Latch
Lever
(TP-3000-R-06)
Rubber disc
(TP-3000-R-05)
Polished sample receptacle
(TP-3000-R-01)
Rubber ring
(TP-3000-R-02)
Polishing disk
(TP-3000-R-03)
Status lamp
Timer jack
DC power inlet
②Make sure that the cover is closed, and the power
is turned off. When the AC adapter is connected to
the outlet, the status lamp will light up.
(1) Push the bottom part
of the bran receptacle
toward the main unit.
(2) Pull the entire case
from the top.
<How to remove>
* Do not put the ngers into the outlet of the removed bran.
The drive unit can catch ngers and severely injure them.
●Status lamp
<On> The device is ready to be used.
<Off> For safety, the sensor is activated and the device is
stopped.
Close the cover while the AC adapter is connected to the
outlet. When the POWER switch is turned off, the status
lamp will be lit to indicate the device is ready to be used.
<Blink> Due to over-current, the device is stopped protecting the
motor.
If the lamp is blinking while the AC adapter is connected to
the outlet, disconnect the plug once, and reconnect. If
blinking or off state continues, contact Kett.
* Do not use other than the specied AC adapter.
Otherwise, it may cause malfunction, re, or electric
shock, etc.

Accessories
Part names Preparation
Features
Polishing Procedure
Others
●Open/close of the lever is linked with the motor
When the lever is pushed, the polished sample will be
ejected to the polished sample receptacle.
●Sample scatter-proof function
To avoid scattering of the sample, the polishing disk will
not be rotated if the cover is fully opened.
●Transparent bran receptacle
The timing for discarding the removed bran can be seen
at a glance.
●Motor overload prevention
If excessive force is applied to the motor and there is a
risk of the motor coil being damaged, the power turns off
automatically.
①Properly attach the bran receptacle to the main unit.
Fully insert the bran receptacle to the outlet of the
removed bran. Note that if the case is not properly
attached, the bran will be scattered during polishing.
①Take a spoonful of sample with the supplied spoon.
* A spoonful of rice measured with the supplied spoon is approxi-
mately 10 g.
②Set the sample on the polishing disk of the
Pearlest and close the cover. Then, lock the latch.
* If bran or dust is left, the cover may not be closed. Before start
polishing, clean the unit and fully close the cover.
③Turn the power ON to start polishing.
The polishing time differs depending on the samples or moisture
content. Set the polishing time referring to the following.
Samples A guide for polishing time
Short rice 30 to 40 sec.
Long rice 40 to 60 sec.
Barley 180 to 240 sec.
* Many broken particles may be generated depending on the sample.
* For barley, optional parts for barley polishing are required. Before
polishing, refer to the back page and assemble the parts correctly.
④Push the lever while the cover is closed.
* If the sample is left in the polishing unit, the clatter may be heard.
Push the lever until the sound is stopped.
⑤The polished sample is ejected to the polished
sample receptacle.
⑥The motor stop when the power is turned off.
⑦Open the cover, and take out the polished sample
receptacle.
* The polished sample receptacle can be used as a strainer. If bran
or dust is left on the tray, clean the tray before use.
Pallet
(TP-3000-A-01)
Brush
(TP-3000-A-02)
AC adapter
(TP-3000-A-05)
Accessory case
(TP-3000-A-06)
Paint brush
(TP-3000-A-03)
Spoon
(Rice : approx. 10 g/spoon)
(TP-3000-A-04)
<Cleaning>
After a few times of polishing, removed bran or dust may
accumulate around the rubber disc or polishing disk.
Clean the polishing unit using the pallet or paint brush.
<Storage>
When storing the instrument, remove the polishing disk,
rubber ring, and rubber disc.
Clean the inside of the bran receptacle. Store the
instrument in a place where the direct sunlight is avoided
under dry conditions.
<Specications>
Power
Input: 100-240 V AC (50/60Hz), 1.4 A MAX
Output: 24 V DC, 2.71 A
Dimensions: 110 (W) x 152 (D) x 176 (H)
Mass: approximately 1.7 kg
Compact Grain Polisher Pearlest
TP-3000
Operating Manual
Thank you for purchasing our grain polisher.
The Compact Grain Polisher Pearlest can polish a
small amount of rice extracted for the purpose of
testing in a short time. Since the rubber plate is used,
capability of bran removal is excellent, and the grains
are well nished. The polished grains can be ejected
only by pushing the motor-linked lever. The Pearlest
can also be used for inspecting condition and mixing
degree of spotted rice inuenced by pentatomid,
burnt, cracked, colored, nonglutinous, or glutinous
rice. Before using this instrument, thoroughly read
this operating manual, and use it properly.
Bran receptacle
(TP-3000-R-04)
Power switch
Cover
Latch
Lever
(TP-3000-R-06)
Rubber disc
(TP-3000-R-05)
Polished sample receptacle
(TP-3000-R-01)
Rubber ring
(TP-3000-R-02)
Polishing disk
(TP-3000-R-03)
Status lamp
Timer jack
DC power inlet
②Make sure that the cover is closed, and the power
is turned off. When the AC adapter is connected to
the outlet, the status lamp will light up.
(1) Push the bottom part
of the bran receptacle
toward the main unit.
(2) Pull the entire case
from the top.
<How to remove>
* Do not put the ngers into the outlet of the removed bran.
The drive unit can catch ngers and severely injure them.
●Status lamp
<On> The device is ready to be used.
<Off> For safety, the sensor is activated and the device is
stopped.
Close the cover while the AC adapter is connected to the
outlet. When the POWER switch is turned off, the status
lamp will be lit to indicate the device is ready to be used.
<Blink> Due to over-current, the device is stopped protecting the
motor.
If the lamp is blinking while the AC adapter is connected to
the outlet, disconnect the plug once, and reconnect. If
blinking or off state continues, contact Kett.
* Do not use other than the specied AC adapter.
Otherwise, it may cause malfunction, re, or electric
shock, etc.

Accessories
Part names Preparation
Features
Polishing Procedure
Others
●Open/close of the lever is linked with the motor
When the lever is pushed, the polished sample will be
ejected to the polished sample receptacle.
●Sample scatter-proof function
To avoid scattering of the sample, the polishing disk will
not be rotated if the cover is fully opened.
●Transparent bran receptacle
The timing for discarding the removed bran can be seen
at a glance.
●Motor overload prevention
If excessive force is applied to the motor and there is a
risk of the motor coil being damaged, the power turns off
automatically.
①Properly attach the bran receptacle to the main unit.
Fully insert the bran receptacle to the outlet of the
removed bran. Note that if the case is not properly
attached, the bran will be scattered during polishing.
①Take a spoonful of sample with the supplied spoon.
* A spoonful of rice measured with the supplied spoon is approxi-
mately 10 g.
②Set the sample on the polishing disk of the
Pearlest and close the cover. Then, lock the latch.
* If bran or dust is left, the cover may not be closed. Before start
polishing, clean the unit and fully close the cover.
③Turn the power ON to start polishing.
The polishing time differs depending on the samples or moisture
content. Set the polishing time referring to the following.
Samples A guide for polishing time
Short rice 30 to 40 sec.
Long rice 40 to 60 sec.
Barley 180 to 240 sec.
* Many broken particles may be generated depending on the sample.
* For barley, optional parts for barley polishing are required. Before
polishing, refer to the back page and assemble the parts correctly.
④Push the lever while the cover is closed.
* If the sample is left in the polishing unit, the clatter may be heard.
Push the lever until the sound is stopped.
⑤The polished sample is ejected to the polished
sample receptacle.
⑥The motor stop when the power is turned off.
⑦Open the cover, and take out the polished sample
receptacle.
* The polished sample receptacle can be used as a strainer. If bran
or dust is left on the tray, clean the tray before use.
Pallet
(TP-3000-A-01)
Brush
(TP-3000-A-02)
AC adapter
(TP-3000-A-05)
Accessory case
(TP-3000-A-06)
Paint brush
(TP-3000-A-03)
Spoon
(Rice : approx. 10 g/spoon)
(TP-3000-A-04)
<Cleaning>
After a few times of polishing, removed bran or dust may
accumulate around the rubber disc or polishing disk.
Clean the polishing unit using the pallet or paint brush.
<Storage>
When storing the instrument, remove the polishing disk,
rubber ring, and rubber disc.
Clean the inside of the bran receptacle. Store the
instrument in a place where the direct sunlight is avoided
under dry conditions.
<Specications>
Power
Input: 100-240 V AC (50/60Hz), 1.4 A MAX
Output: 24 V DC, 2.71 A
Dimensions: 110 (W) x 152 (D) x 176 (H)
Mass: approximately 1.7 kg
Compact Grain Polisher Pearlest
TP-3000
Operating Manual
Thank you for purchasing our grain polisher.
The Compact Grain Polisher Pearlest can polish a
small amount of rice extracted for the purpose of
testing in a short time. Since the rubber plate is used,
capability of bran removal is excellent, and the grains
are well nished. The polished grains can be ejected
only by pushing the motor-linked lever. The Pearlest
can also be used for inspecting condition and mixing
degree of spotted rice inuenced by pentatomid,
burnt, cracked, colored, nonglutinous, or glutinous
rice. Before using this instrument, thoroughly read
this operating manual, and use it properly.
Bran receptacle
(TP-3000-R-04)
Power switch
Cover
Latch
Lever
(TP-3000-R-06)
Rubber disc
(TP-3000-R-05)
Polished sample receptacle
(TP-3000-R-01)
Rubber ring
(TP-3000-R-02)
Polishing disk
(TP-3000-R-03)
Status lamp
Timer jack
DC power inlet
②Make sure that the cover is closed, and the power
is turned off. When the AC adapter is connected to
the outlet, the status lamp will light up.
(1) Push the bottom part
of the bran receptacle
toward the main unit.
(2) Pull the entire case
from the top.
<How to remove>
* Do not put the ngers into the outlet of the removed bran.
The drive unit can catch ngers and severely injure them.
●Status lamp
<On> The device is ready to be used.
<Off> For safety, the sensor is activated and the device is
stopped.
Close the cover while the AC adapter is connected to the
outlet. When the POWER switch is turned off, the status
lamp will be lit to indicate the device is ready to be used.
<Blink> Due to over-current, the device is stopped protecting the
motor.
If the lamp is blinking while the AC adapter is connected to
the outlet, disconnect the plug once, and reconnect. If
blinking or off state continues, contact Kett.
* Do not use other than the specied AC adapter.
Otherwise, it may cause malfunction, re, or electric
shock, etc.

Accessories
Part names Preparation
Features
Polishing Procedure
Others
●Open/close of the lever is linked with the motor
When the lever is pushed, the polished sample will be
ejected to the polished sample receptacle.
●Sample scatter-proof function
To avoid scattering of the sample, the polishing disk will
not be rotated if the cover is fully opened.
●Transparent bran receptacle
The timing for discarding the removed bran can be seen
at a glance.
●Motor overload prevention
If excessive force is applied to the motor and there is a
risk of the motor coil being damaged, the power turns off
automatically.
①Properly attach the bran receptacle to the main unit.
Fully insert the bran receptacle to the outlet of the
removed bran. Note that if the case is not properly
attached, the bran will be scattered during polishing.
①Take a spoonful of sample with the supplied spoon.
* A spoonful of rice measured with the supplied spoon is approxi-
mately 10 g.
②Set the sample on the polishing disk of the
Pearlest and close the cover. Then, lock the latch.
* If bran or dust is left, the cover may not be closed. Before start
polishing, clean the unit and fully close the cover.
③Turn the power ON to start polishing.
The polishing time differs depending on the samples or moisture
content. Set the polishing time referring to the following.
Samples A guide for polishing time
Short rice 30 to 40 sec.
Long rice 40 to 60 sec.
Barley 180 to 240 sec.
* Many broken particles may be generated depending on the sample.
* For barley, optional parts for barley polishing are required. Before
polishing, refer to the back page and assemble the parts correctly.
④Push the lever while the cover is closed.
* If the sample is left in the polishing unit, the clatter may be heard.
Push the lever until the sound is stopped.
⑤The polished sample is ejected to the polished
sample receptacle.
⑥The motor stop when the power is turned off.
⑦Open the cover, and take out the polished sample
receptacle.
* The polished sample receptacle can be used as a strainer. If bran
or dust is left on the tray, clean the tray before use.
Pallet
(TP-3000-A-01)
Brush
(TP-3000-A-02)
AC adapter
(TP-3000-A-05)
Accessory case
(TP-3000-A-06)
Paint brush
(TP-3000-A-03)
Spoon
(Rice : approx. 10 g/spoon)
(TP-3000-A-04)
<Cleaning>
After a few times of polishing, removed bran or dust may
accumulate around the rubber disc or polishing disk.
Clean the polishing unit using the pallet or paint brush.
<Storage>
When storing the instrument, remove the polishing disk,
rubber ring, and rubber disc.
Clean the inside of the bran receptacle. Store the
instrument in a place where the direct sunlight is avoided
under dry conditions.
<Specications>
Power
Input: 100-240 V AC (50/60Hz), 1.4 A MAX
Output: 24 V DC, 2.71 A
Dimensions: 110 (W) x 152 (D) x 176 (H)
Mass: approximately 1.7 kg
Compact Grain Polisher Pearlest
TP-3000
Operating Manual
Thank you for purchasing our grain polisher.
The Compact Grain Polisher Pearlest can polish a
small amount of rice extracted for the purpose of
testing in a short time. Since the rubber plate is used,
capability of bran removal is excellent, and the grains
are well nished. The polished grains can be ejected
only by pushing the motor-linked lever. The Pearlest
can also be used for inspecting condition and mixing
degree of spotted rice inuenced by pentatomid,
burnt, cracked, colored, nonglutinous, or glutinous
rice. Before using this instrument, thoroughly read
this operating manual, and use it properly.
Bran receptacle
(TP-3000-R-04)
Power switch
Cover
Latch
Lever
(TP-3000-R-06)
Rubber disc
(TP-3000-R-05)
Polished sample receptacle
(TP-3000-R-01)
Rubber ring
(TP-3000-R-02)
Polishing disk
(TP-3000-R-03)
Status lamp
Timer jack
DC power inlet
②Make sure that the cover is closed, and the power
is turned off. When the AC adapter is connected to
the outlet, the status lamp will light up.
(1) Push the bottom part
of the bran receptacle
toward the main unit.
(2) Pull the entire case
from the top.
<How to remove>
* Do not put the ngers into the outlet of the removed bran.
The drive unit can catch ngers and severely injure them.
●Status lamp
<On> The device is ready to be used.
<Off> For safety, the sensor is activated and the device is
stopped.
Close the cover while the AC adapter is connected to the
outlet. When the POWER switch is turned off, the status
lamp will be lit to indicate the device is ready to be used.
<Blink> Due to over-current, the device is stopped protecting the
motor.
If the lamp is blinking while the AC adapter is connected to
the outlet, disconnect the plug once, and reconnect. If
blinking or off state continues, contact Kett.
* Do not use other than the specied AC adapter.
Otherwise, it may cause malfunction, re, or electric
shock, etc.

Pearlest Timer TZ-910 (option)
Operating Manual
Parts for Barley Polishing (option)
Operating Manual
①Disassemble the rice polishing parts using the
supplied pallet.
(washer, polishing disk, rubber ring, rubber disc)
②Set the polishing time using the [+]/[-] key.
Long pless of the key will change the value swiftly.
③Take a spoonful of sample with the supplied
spoon.
④Set the sample on the polishing disk of the
Pearlest and close the cover. Then, lock the latch.
* If bran or dust is left, the cover may not be closed. Before start
polishing, clean the unit and fully close the cover.
⑤Pless the [START/STOP] key.
The set time for polishing will start counting down in
steps of 1 second.
⑦Push the lever while the cover of the Pearlest is
closed.
* If the sample is left in the polishing unit, the clatter may be heard.
Push the lever until the sound is stopped.
⑧The polished sample will be ejected to the
polished sample receptacle.
⑨When the motor is stopped, open the cover, and
take out the polished sample receptacle.
⑩Pless the [ON/OFF] key to turn off the power.
⑥Polishing ends at 0 second.
The display restores the preset time.
Beeps
①Connect the Pearlest and the timer using the
dedicated cable.
②Connect the AC adapter to the Pearlest DC power
inlet.
②Assemble the parts for polishing the barley.
(metal ring, metal disk (a), washer for barley, metal disk (b))
①Pless the [ON/OFF] key.
The previously set time will be displayed.
Accessories
Accessories
How to Assemble
How to Connect
Directions (The power of the Pearlest is always OFF.)
The polishing time can be set between 0 second
and 59 minutes 59 seconds.
Plessing the [ON/OFF] key will start and end the
polishing in the preset time.
By replacing the polishing parts for rice to the
barley, barley polishing will become available.
Also, the parts can be used for rice suitable for
brewing sake.
* In order to avoid loosening of the parts, rmly x with the supplied
pallet.
Disc xing screw
(TP-3000-O-07)
Hex wrench
(TP-3000-O-06)
Fixing nut
Washer
Polishing
disk
Rubber
ring
Disc xing
screw Rubber disc
Fixing nut
Washer for barley
Metal disk (a)
Metal ring
Metal disk (b)
Disc xing
screw
Cautions
When using the Pearlest Timer TZ-910, it is
required to set the power of the Compact
Grain Polisher Pearlest TP-3000 always OFF.
If the power in ON, the timer is disabled.
The power has to be
OFF.
If it is ON, the
Pearlest timer cannot
be used.
Pearlest timer
(TP-3000-O-01)
Dedicated cable
(TP-3000-O-02)
Washer for barley
* thicker than rice
(TP-3000-O-08)
Metal disk (a)
(TP-3000-O-03)
Metal Ring
(TP-3000-O-05)
Metal disk (b)
(TP-3000-O-04)
<Specications>
External Dimensions & Weight: 128 (W) x 98 (D) x 56 (H)
mm, 0.2kg
0 6 02 3 8 - 01
* Do not use other than the specied AC adapter. Other-
wise, it may cause malfunction, re, or electric shock,
etc.
Example) Polishing time: 1 min. 10 sec.
Beeps
shortly
twice
Beeps
shortly
twice
* When the [START/STOP]
key is plessed during polish-
ing, the display restores the
preset time.
Beeps
shortly

Pearlest Timer TZ-910 (option)
Operating Manual
Parts for Barley Polishing (option)
Operating Manual
①Disassemble the rice polishing parts using the
supplied pallet.
(washer, polishing disk, rubber ring, rubber disc)
②Set the polishing time using the [+]/[-] key.
Long pless of the key will change the value swiftly.
③Take a spoonful of sample with the supplied
spoon.
④Set the sample on the polishing disk of the
Pearlest and close the cover. Then, lock the latch.
* If bran or dust is left, the cover may not be closed. Before start
polishing, clean the unit and fully close the cover.
⑤Pless the [START/STOP] key.
The set time for polishing will start counting down in
steps of 1 second.
⑦Push the lever while the cover of the Pearlest is
closed.
* If the sample is left in the polishing unit, the clatter may be heard.
Push the lever until the sound is stopped.
⑧The polished sample will be ejected to the
polished sample receptacle.
⑨When the motor is stopped, open the cover, and
take out the polished sample receptacle.
⑩Pless the [ON/OFF] key to turn off the power.
⑥Polishing ends at 0 second.
The display restores the preset time.
Beeps
①Connect the Pearlest and the timer using the
dedicated cable.
②Connect the AC adapter to the Pearlest DC power
inlet.
②Assemble the parts for polishing the barley.
(metal ring, metal disk (a), washer for barley, metal disk (b))
①Pless the [ON/OFF] key.
The previously set time will be displayed.
Accessories
Accessories
How to Assemble
How to Connect
Directions (The power of the Pearlest is always OFF.)
The polishing time can be set between 0 second
and 59 minutes 59 seconds.
Plessing the [ON/OFF] key will start and end the
polishing in the preset time.
By replacing the polishing parts for rice to the
barley, barley polishing will become available.
Also, the parts can be used for rice suitable for
brewing sake.
* In order to avoid loosening of the parts, rmly x with the supplied
pallet.
Disc xing screw
(TP-3000-O-07)
Hex wrench
(TP-3000-O-06)
Fixing nut
Washer
Polishing
disk
Rubber
ring
Disc xing
screw Rubber disc
Fixing nut
Washer for barley
Metal disk (a)
Metal ring
Metal disk (b)
Disc xing
screw
Cautions
When using the Pearlest Timer TZ-910, it is
required to set the power of the Compact
Grain Polisher Pearlest TP-3000 always OFF.
If the power in ON, the timer is disabled.
The power has to be
OFF.
If it is ON, the
Pearlest timer cannot
be used.
Pearlest timer
(TP-3000-O-01)
Dedicated cable
(TP-3000-O-02)
Washer for barley
* thicker than rice
(TP-3000-O-08)
Metal disk (a)
(TP-3000-O-03)
Metal Ring
(TP-3000-O-05)
Metal disk (b)
(TP-3000-O-04)
<Specications>
External Dimensions & Weight: 128 (W) x 98 (D) x 56 (H)
mm, 0.2kg
0 6 02 3 8 - 01
* Do not use other than the specied AC adapter. Other-
wise, it may cause malfunction, re, or electric shock,
etc.
Example) Polishing time: 1 min. 10 sec.
Beeps
shortly
twice
Beeps
shortly
twice
* When the [START/STOP]
key is plessed during polish-
ing, the display restores the
preset time.
Beeps
shortly

Parts for Barley Polishing (option)
Operating Manual
①Disassemble the rice polishing parts using the
supplied pallet.
(washer, polishing disk, rubber ring, rubber disc)
②Assemble the parts for polishing the barley.
(metal ring, metal disk (a), washer for barley, metal disk (b))
Accessories
How to Assemble
By replacing the polishing parts for rice to the
barley, barley polishing will become available.
Also, the parts can be used for rice suitable for
brewing sake.
* In order to avoid loosening of the parts, rmly x with the supplied
pallet.
Disc xing screw
(TP-3000-O-07)
Hex wrench
(TP-3000-O-06)
Fixing nut
Washer
Polishing
disk
Rubber
ring
Disc xing
screw Rubber disc
Fixing nut
Washer for barley
Metal disk (a)
Metal ring
Metal disk (b)
Disc xing
screw
Washer for barley
* thicker than rice
(TP-3000-O-08)
Metal disk (a)
(TP-3000-O-03)
Metal Ring
(TP-3000-O-05)
Metal disk (b)
(TP-3000-O-04)
0 6 02 3 8 - 01