Keurig B81 User manual

1

2
IMPORTANT SAFEGUARDS Safe Operation & Use
When using electrical appliances, basic safety precautions should be followed, including the following:
1. Read all instructions before usin .
2. Do not touch hot surfaces. Use handles and knobs when available.
3. This appliance must be properly installed and located in accordance with
these instructions before it is used.
4. The use of accessory attachments not recommended by the appliance
manufacturer may result in fire, electrical shock or injury to persons.
5. Do not place on or near a hot as or electric burner, or in a heated oven.
6. Do not use outdoors.
7. To protect a ainst fire, electric shock and injury do not immerse cords,
plu s, or the appliance in water or any other liquid.
8. Do not overfill the Water Reservoir with water.
9. Use only water in this appliance! Do not put any other liquids or foods in
the Water Reservoir except as instructed in the Cleanin Instructions in
this uide.
10. Turn off and unplu the Brewer before cleanin or maintenance. Allow to
cool before puttin on or takin off parts and before cleanin the
appliance.
11. For best operation, plu the appliance into its own electrical outlet on a
dedicated circuit to prevent flickerin of li hts, blowin of fuses or trippin
a circuit breaker.
12. Do not operate any appliance with a dama ed cord or plu or after the
appliance malfunctions or is dama ed in any manner. Contact Keuri ®
Customer Service to report any malfunction of or dama e to the Brewer.
13. Do not let the cord han over the ed e of the table or counter, or touch hot
surfaces.
14. To disconnect, press the Power Button on the Brewer to ‘OFF’ status and
then remove the plu from the wall outlet.
15. Close supervision is necessary when any appliance is used by or near
children.
16. Do not lift the Handle to open the Lid of the Brewer while brewing is
in progress.
17. Always keep the Water Reservoir Lid on the Water Reservoir unless you
are refillin it.
18. This appliance is equipped with a power cord havin a roundin wire with
a roundin plu . The appliance must be rounded usin a 3-hole
properly rounded outlet. In the event of an electrical short circuit,
roundin reduces the risk of electrical shock.
19. If the outlet is a standard 2-pron wall outlet, it is your personal
responsibility and obli ation to have it replaced with a properly rounded
3-pron wall outlet.
20. Do not, under any circumstances, cut or remove the third ( round) pron
from the power cord or use an adapter.
21. Consult a qualified electrician if the roundin instructions are not
completely understood, or if doubt exists as to whether the appliance is
properly rounded.
22. Do not use the appliance for other than its intended use.

3
CAUTION: There are two sharp needles that puncture the K-Cup® port on
pack, one above the K-Cup Holder and the other n the bottom of the K-Cup
Holder. To avo d r sk of njury, do not put your f ngers n the K-Cup
Assembly Hous ng.
CAUTION: There s extremely hot water n the K-Cup Holder dur ng the
brew process. To avo d r sk of njury, do not l ft the Handle or open the K-
Cup Assembly Hous ng dur ng the brew ng process.
SHO T CO D INST UCTIONS: A short power supply cord s prov ded
to reduce the r sk of becom ng entangled n or tr pp ng over a longer cord.
If an extens on cord s used, (1) the marked electr cal rat ng of the cord set
or extens on cord should be at least as great as the electr cal rat ng of the
appl ance; (2) the cord should be arranged so that t w ll not drape over the
countertop or tabletop where t can be pulled on by ch ldren or tr pped over
un ntent onally; and (3) the extens on cord must nclude a 3-prong
ground ng plug.
THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.
TABLE OF CONTENTS
KEURIG® GOURMET SINGLE CUP HOME BREWING SYSTEM
B81 — Usin Your Brewer
SET-UP
Helpful Hints..........................................................................................4
Unpackin .............................................................................................4
Features................................................................................................5
SECTION 1 — SET-UP & FIRST BREW
Set-Up & First Brew..............................................................................6
SECTION 2 — CONTROLS & INDICATORS
Settin the Clock...................................................................................9
Pro rammin On/Off Features..............................................................9
Pro rammin Favorite Button 1 & 2.....................................................11
Pro rammin Brew Temperature.........................................................12
SECTION 3 — CLEANING & MAINTENANCE
Cleanin ...............................................................................................12
De-Scalin ...........................................................................................13
Stora e................................................................................................13
ecord your Brewer Serial Number here.

4
Set-up
Helpful Hints
1. Keep your Brewer turned “ON” at all times. To brew a fresh cup of
coffee, tea or hot cocoa anytime you want, we su est you keep
your Brewer turned “ON” all the time. However, the Brewer is fully
pro rammable so you can set it to turn on and off automatically to
match your schedule. Or, if you prefer, set the Brewer to
automatically turn off after a period of time. Follow the simple
instructions on pa es 9–10 to make usin the Brewer convenient
for you.
2. For the best tastin ourmet coffee, tea or hot cocoa, Keuri
recommends usin bottled water or the Keuri ® Water Filter Starter
Kit (available at www.keuri .com). Water quality varies from place
to place. If you notice an undesirable taste in your cup of coffee,
such as chlorine or other mineral tastes, we recommend you
consider usin bottled water or water from a filtration system.
3. Customize the Size, Flavor & Brew That’s Perfect for You.™ With
the choice of over 200 varieties of K-Cups and 5 brew sizes (Extra-
Small Cup-3.25 oz., Small Cup-5.25 oz., Small Mu -7.25 oz., Lar e
Mu -9.25 oz., and Travel Mu -11.25 oz.) your Keuri ® Brewer
ives you endless options to customize the size, flavor and brew
that’s perfect for you. For a stron , intense cup, select an Extra
Bold K-Cup® (with up to 30% more round coffee than re ular
varieties) and brew the size that’s ri ht for you. The smaller the
brew size, the more intense flavor in your cup. The lar er the brew
size, the less intense flavor in your cup.
4. Plu Brewer into its own rounded outlet. If the electric circuit is
overloaded with other appliances, your Brewer may not function
properly. The Brewer should be operated on its own circuit,
separate from other appliances.
5. Brewin into a travel mu . To brew into a travel mu , simply
remove the Drip Tray Assembly and place the travel mu on the
Drip Tray Base.
6. De-scale Brewer re ularly. Please see pa e 13 for instructions.
Unpacking Instructions
1. Place Brewer box on a lar e steady surface (such as a table or
countertop) or on the floor. Open the box.
2. Remove enclosed literature.
3. Turn the box on its side with front of box face down.
4. Reach into the box and rasp the plastic ba that contains the
Brewer.
5. Carefully pull the plastic ba (and packa in materials) toward you
and out of the box. The Brewer will still be encased in the polyfoam
and be on its side. The Water Reservoir Assembly will be encased
on the opposite side of the polyfoam.
6. Before removin the Brewer from the polyfoam packa in material,
carefully lift the Water Reservoir Assembly out of the polyfoam and
place it upri ht on a flat, steady surface.
7. Once the Water Reservoir Assembly is unpacked, remove the top
polyfoam packa in material.
8. Carefully lift Brewer off of the bottom polyfoam and place it upri ht
on a flat, steady surface.
9. Lift plastic ba off of Brewer and Water Reservoir Assembly.
10. Record the serial number for this Brewer on pa e 3 of this uide.
The serial number can be found on the bottom of the Brewer box or
on the Brewer behind the Drip Tray (when removed).
11. Place the Brewer upri ht on a flat, steady surface. Remove the
tape from the Water Reservoir.
We recommend you save all packin materials in case future shippin
of the product is necessary.
WA NING:
Keep all plastic bags away from children.

5
Features – Model B81 Brewer

6
SECTION 1 Set-Up & First Brew
IMPO TANT: You cannot use your Keuri ® Brewer until it
has been set up for its first use.
NOTE: If Brewer has been exposed to temperatures below
freezin , allow Brewer at least two hours to reach room
temperature before brewin . A frozen or extremely cold
Brewer will not operate.
Setting Up Your Brewer
1. Unwrap cord and plu the Brewer into a
rounded outlet. Remove all pieces of
packin tape and clear plastic sticker
from Touch Screen display.
2. Place a lar e mu (10 oz. minimum) on
the Drip Tray Plate.
3. Remove the Water Reservoir from
Brewer by first removin Lid from the
Water Reservoir (fi . 1), then liftin the
Water Reservoir strai ht up and to the
left of the Brewer. (may be ti ht), (fi . 2).
Rinse with fresh water.
4. Fill Water Reservoir with bottled or
filtered water so that the water level is
just below the MAX fill line of the Water
Reservoir.
5. Place Water Reservoir base into the left
side of the Brewer and be sure the
Water Reservoir Lock Tab en a es with
the Brewer. Replace Lid on Water
Reservoir.
6. Press and release the Power Button
found directly behind the ri ht side of
the Brewer.
7. The Touch Screen will come on and
indicate “NOT READY”.
NOTE: A K-Cup should not be used for this
sequence.
8. The Brewer will automatically fill the
internal tank with water and then the
water will be heated. This will take about
4 minutes. Durin the heatin period,
“NOT READY” (fi . 3) is displayed on
the Touch Screen. Do not lift Brewer
Handle during this ‘heating period’.
Once the water is heated, “READY TO
BREW” will be displayed and the BREW
Button will be illuminated (fi . 4).
9. Press the BREW Button to start a
cleansin brew without a K-Cup. Pour
the hot water into the sink.
NOTE: A K-Cup should not be used for th s
Sequence.
10. The one-time set-up process is now
complete and you are ready to brew!
NOTE: The Brewer may take 15-30 seconds
between brews and then “READY TO
BREW” will be displayed.
eady to Brew Your First Cup
1. Touch Screen will indicate “READY TO
BREW”.
2. Place a cup or mu on the Drip Tray
Plate.
3. Lift the Handle and the K-Cup® Holder
will open toward you (fi . 5).
4. Select a K-Cup portion pack.
NOTE: Do not remove
the foil lid or puncture
the K-Cup.

7
SECTION 1 Set-Up & First Brew (continued)
5. Place a K-Cup portion pack in the K-
Cup Holder (fi . 6).
CAUTION: There are two sharp needles
that puncture the K-Cup, one abo e the
K-Cup Holder and the other in the
bottom of the K-Cup Holder. To a oid
risk of injury, do not put your fingers in
the K-Cup Assembly Housing.
6. Lower the Handle to close the Lid over
the K-Cup Holder. (When it is closed
completely, the Touch Screen will
indicate “READY TO BREW”).
a. All brew size icons are lit with the default
size is illuminated (fi . 7). To choose a
different size, press the cup icon of your
choice.
NOTE: The Small Mug (7.25 oz.
serv ng) s the factory set default brew
s ze. To program your favor te brew s ze
see page 11 “How to Program the Favor te
Button 1 & 2”.
b. Your choices are an Extra-Small Cup
(3.25 oz servin ), Small Cup (5.25 oz.
servin ), a Small Mu (7.25 oz. servin ),
a Lar e Mu (9.25 oz. servin ) or a
Travel Mu (11.25 oz. servin ).
c. The stren th of the brew can be
controlled by selectin the Re ular or
Stron selections on the Touch Screen.
If you wish to have a more robust cup of
coffee select the Stron settin . This
unique “pulsatin ” brew settin slows
down the brewin process to allow the
water to have more contact time with the
coffee rinds.
NOTE: The Strong brew strength sett ng takes
longer to brew compared to the Regular brew
strength sett ng.
SPECIAL NOTE: For “Deluxe K-Cups” there
are programmed rec pes and the touch screen
may d ffer from normal operat on – please rev ew
the nsert sent w th the K-Cups for nformat on.
d. Once size is chosen, press the BREW
Button. BREW Button will stop flashin .
7. The Touch Screen will now display the
word ‘BREWING’ (fi . 8).
CAUTION: There is extremely hot water
in the K-Cup Holder during the brew
process. To a oid risk of injury, do not
lift the Handle or open the K-Cup
Assembly Housing during the brew
process.
8. There may be a short pause prior to
coffee bein dispensed. The entire brew
process lasts for approximately 1 minute
and ends with a burst of air to remove
all liquid from the K-Cup.
9. Lift the Handle, remove and dispose of
the used K-Cup.
CAUTION: K-Cup will be hot.
10. Enjoy your first cup of Keuri Brewed®
ourmet coffee, tea or hot cocoa!
11. Your Brewer may display “NOT READY”
as it heats water for the next brew cycle.
The “READY TO BREW” and
“HEATING” indication will return to the
Touch Screen in about 15 seconds.

8
SECTION 1 Set-Up & First Brew (continued)
Stopping the Brew Process
If you need to stop the brewin after the process has started, press and
release the Power Button to turn the Brewer ‘OFF’. The flow of coffee, tea or
hot cocoa will stop, the heatin element will shut off and the li hts
illuminatin the Touch Screen and Water Reservoir will disappear.
NOTE: You may not get the brew s ze selected n your cup dur ng for your next
brew. We recommend that you perform a cleans ng brew w th water-only after a
term nated brew. Then your NEXT brew w ll be the volume you have selected.
Adding Water
The Touch Screen of your Brewer will indicate when the water level in the
tank is low or if the Water Reservoir has been removed by displayin the
words “ADD WATER” (fi . 9). The white li ht in the Water Reservoir will also
blink when water needs to be added. The Brewer will not allow you to brew
when “ADD WATER” is displayed (fi . 9).
The Water Reser oir can be filled in two ways.
1. Lift off the Water Reservoir Lid and pour
water directly into the Water Reservoir
while it is still attached to the Brewer,
then replace the Lid.
2. Remove the Water Reservoir from
Brewer by first removin Lid from the
Water Reservoir, then liftin the Water
Reservoir strai ht up and toward the left
of the Brewer. Fill with water. Place the
Water Reservoir back on the Brewer
and replace the Lid.
Note: In the back of the Water Reservoir
there is a fin er indent for secure rip.
IMPO TANT: Do not remo e the Water
Reser oir during the brewing process.
Brewing Hot Water
Your Brewer is able to produce hot water for makin hot cocoa from a
packet, for use in cookin , for makin soups, etc. Simply follow the
instructions on pa e 6 — “Ready To Brew Your First Cup” without addin a
K-Cup.
NOTE: After brew ng a hot cocoa K-Cup, we recommend runn ng a hot water brew
cycle w thout a K-Cup.
Purging the Brewer
If your Brewer has not been used for more than one week, you should pur e
the water from the inner tank.
1. If there is water in the Water Reservoir, remove the Lid, then lift the
rinse and refill with water. Place the Water Reservoir back on the
Brewer and replace the Lid. (If there is no water in the Water
Reservoir, simply refill.)
2. Be sure the Brewer is turned on. Raise and lower the Handle on the
Brewer without insertin a K-Cup.
3. The Touch Screen will display “READY TO BREW”. Brew a Travel
Mu (11.25 oz. servin ) of water (do not use a K-Cup).
4. Repeat steps 2 and 3 two more times to completely pur e water
from inner tank.
If you are experiencing any problems with your Brewer, please contact
Customer Ser ice at 1.866

9
SECTION 2 Controls & Indicators (Touch Screen)
Setting the Clock
Settin the clock is optional. When the clock is set, the time will appear in
the Touch Screen. NOTE: You must set the clock if you will be usin the
On/Off Time pro rammin feature.
1. Press the MENU Button.
Note: If Touch Screen is not illuminated,
simply touch to illuminate options.
2. The first time settin the time – the word
‘OFF’ will appear at the top of the Touch
Screen to indicate that the clock is not
set (fi . 10). The pro rammin options
will appear on the Touch Screen with a
small arrow pointin to ‘SET CLOCK’.
The “H” icon is illuminated, Hour
numbers will flash.
3. Press or hold the Up or Down Button
until you have reached the appropriate
hour. If the hour has passed 12, “PM”
will be shown. Once “H” is set, press
MENU once to set “M”. The “M” icon is
illuminated, Minute numbers will flash.
4. Press or hold the Up or Down Button to
set the minutes.
5. When you have reached the correct
time, press the MENU Button seven
times to scroll throu h the remainin
pro rammin steps.
6. The correct time should now be
displayed in the Touch Screen.
NOTE: If power s nterrupted to the Brewer by unplugg ng
t, or f power s lost, follow the procedure above to reset the
t me as the clock w ll not be v s ble unt l the t me s set.
Brew s ze and brew temperature menu sett ngs are
remembered and restored automat cally. All other sett ngs
w ll be restored automat cally after clock s set.
Programming On/Off Features
The Brewer provides three modes so that you can enjoy ourmet coffee, tea
or hot cocoa on your own schedule. By pro rammin your Brewer to turn on
each mornin , you will never have to wait for the Brewer to warm up to brew
a ourmet cup of coffee. It will take the Brewer approximately 4 minutes to
warm up from room temperature.
1. Leave it ON all the time. The Brewer
can be left on all the time so that it is
always ready to brew a fresh cup of
ourmet coffee, tea or hot cocoa. To
turn the Brewer off at any time, simply
press and release the Power Button.
Press and release the Power Button
a ain to restore power to the Brewer.
You will have to wait for the water to
heat up before the Brewer is ready to
brew.
2. Set the Brewer to “AUTO OFF” followin
a specified period of time after the last
brew.
a. Press the MENU Button three times to
pro ram the Auto Off feature. The
Touch Screen will now display the
pro rammin options with a small arrow
next to “SET AUTO OFF” (fi . 11).
b. Press or hold the Up or Down Button to
advance 1 hour at a time, up to 9 hours.
c. After settin the desired Auto Off time,
press the MENU Button six times to
scroll throu h the remainin
pro rammin options and exit the
pro rammin mode. “AUTO OFF SET”
(fi . 12) will now be displayed to indicate
that it has been set.

10
d. To cancel the Auto Off feature, press
the MENU Button three times to reach
the “AUTO OFF” pro rammin mode.
Press or hold the Down or UP Button to
advance one hour at a time until “OFF”
is displayed.
3. Pro ram your Brewer for a specific
On/Off Time.
NOTE: To use this pro rammin feature, the
clock must be set to the correct time. The
clock will not be displayed unless the time is
set.
a. After settin the correct time (required),
press the MENU Button four times to
pro ram On Time feature. The Touch
Screen will show the pro rammin
options with a small arrow next to “SET
ON TIME” (fi . 13).
b. Press or hold the Up or Down Button to
scroll throu h the hours to your desired
“ON TIME” hour. Press MENU to set M.
c. Press or hold the Down or Up Button to
scroll throu h the minutes to your
desired “ON TIME” minutes.
d. After settin the desired time, press the
MENU Button to save the “ON TIME”
and move to the “SET OFF TIME” (fi .
14).
e. If you want to set an “OFF TIME”, repeat
the procedure above in steps b & c to
set your desired “OFF TIME” (fi . 14).
f. To complete the process, press the
MENU Button two more times to exit the
pro rammin mode. The Touch Screen
will now indicate the options you have
set.
. The Auto On time and Auto Off time
functions operate independently from
one another. To cancel either set
function, follow the steps above and use
the UP and Down Buttons to advance to
12:00 AM. When you reach 12:00 AM,
the Touch Screen will display ‘OFF’ and
the function will be disabled.
EXAMPLE: If you chose to set the On
Time at 6:55 AM and the Off Time for
10:00 PM, then the Brewer will be
“READY TO BREW” and maintain hot
water in the tank durin that time so that
it is always ready for you to brew. If you
wanted to brew outside this window,
simply press the Power Button and you
can brew as soon as the water is heated
and the “READY TO BREW” indicator is
displayed on the Touch Screen.
NOTE: The Auto Off timer and the
On/Off Time pro rammin options
operate independently, but can also be
pro rammed to work to ether. For
example, you can set the On Time
function to turn on at 7:00 AM and then
set the Auto Off timer function to turn off
the Brewer two hours after the last brew.

11
How to Program the Favorite Button 1 & 2
Pro ram two of your favorite brew selections. This function saves your
favorite two brew selections to memory. The Re ular brew stren th and the
small mu (7.25 oz servin ) brew size are the factory default settin s.
1. If the Touch Screen is not illuminated, simply touch the screen.
2. Press the Favorite 1 Button twice
quickly (fi . 15).
NOTE: The Favor te 1 Button w ll flash after
qu ckly press ng t tw ce.
3. Select the brew stren th by pressin
either the Re ular or Stron Button and
then select the brew size by pressin a
brew size icon.
NOTE: Your cho ces are a stronger Extra-Small
Cup (3.25 oz serv ng), Small Cup (5.25 oz
serv ng), Small Mug (7.25 oz serv ng), a Large
Mug (9.25 oz serv ng) or a Travel Mug (11.25 oz
serv ng) (f g. 16).
4. Press the Favorite 1 Button once to
confirm your selections to memory.
5. Press the Favorite 2 Button twice
quickly and repeat steps 1-4 above to
pro ram a second selection to memory.
NOTE: Press the Favor te 1 or Favor te 2 Button
to rev ew the programmed brew strength and
brew s ze (f g. 15).
Brew Using the Favorite Button
1. Touch screen will indicate “READY TO BREW”.
2. Place a cup or mu on the Drip Tray Plate.
3. Lift the Handle and the K-Cup® Holder will open.
4. Select a K-Cup portion pack.
NOTE: Do not remove the foil lid or puncture the K-Cup.
5. Place a K-Cup portion pack in the K-Cup Holder.
CAUTION: There are two sharp needles that puncture the K-Cup, one above
the K-Cup Holder and the other in the bottom of the K-Cup Holder. To avoid
risk of injury, do not put your fin ers in the K-Cup Assembly Housin .
6. Lower the Handle to close the Lid over the K-Cup Holder. (When it is
closed completely, the Touch Screen will indicate “READY TO BREW”
and the Brew Button will be illuminated for up to 60 seconds.
7. Press either the Favorite 1 or Favorite 2 Button (fi . 15).
8. Once the Favorite Button has been selected press the illuminated
BREW Button.

12
Programming Brew Temperature (187° – 197º F)
The Brewer brews at a preset temperature of 192°. You can adjust this
temperature up/down by 5 de rees if you prefer a cooler cup of coffee, tea
or hot cocoa. Simply follow the instructions below.
1. Press the MENU Button on the Touch Screen ei ht times to pro ram
the Brew Temperature feature.
2. The Touch Screen will now display the pro rammin options with a
small arrow next to “SET BREW TEMP” (fi . 17). Also, the temperature
192° (initial settin ) will be displayed at the top of the Touch Screen to
indicate the current temperature settin .
3. Press or hold the Down and Up Buttons to decrease or increase the
brew temperature.
4. Once you have reached your desired brew temperature, press the
MENU Button once to exit the pro rammin mode. “BREW TEMP SET”
will be displayed in the Touch Screen if you have chan ed it from 192°.
5. To chan e the brew temperature a ain, repeat steps 1 throu h 3 to
chan e the temperature up or down, rememberin that the temperature
can only be between 187° and 197°.
NOTE: At h gh alt tudes (over 5,000 feet) f bo l ng occurs
use the temperature adjustment to lower the temperature.
SECTION 3 Cleanin & Maintenance
Cleaning External Parts
Re ular cleanin of the Brewer’s external components is recommended.
1. Never immerse the Brewer in water or other liquids. The Housin
and other external components may be cleaned with a soapy, damp,
non-abrasive cloth.
2. The Drip Tray can accumulate up to 18 ounces of overflow. The
Drip Tray and Drip Tray Plate should be periodically inspected and
rinsed clean. To remove the Drip Tray Assembly, simply slide it toward
you, keepin it level at all times to avoid spillin . The Drip Tray and
Drip Tray Plate should not be placed in the dishwasher. They should
be cleaned with a damp, soapy, non-abrasive cloth and rinsed
thorou hly.
Cleaning the K-Cup Holder Assembly
1. Cleaning the Parts —The K-Cup Holder Assembly can be placed
onto the top shelf of a dishwasher. NOTE: Use low temperature
cycles in the dishwasher. To remove from the Brewer, open the
cover by liftin the Handle. Grasp the top of the K-Cup Holder with
one hand while pushin up on the bottom of the K-Cup® Holder
from underneath with the other until it releases. After cleanin , ali n
the K-Cup Holder with the openin usin the two front ribs as a
uide, and snap into place from the top.
2. Cleaning the Funnel —The Funnel can
be removed from the K-Cup® Holder by pullin on
it until it pops off (fi . 18). The Funnel is
dishwasher safe. To replace it, just snap it back
onto the K-Cup Holder Assembly.
3. Cleaning the Exit Needle —The Exit
Needle is located on the inside bottom of the K-
Cup Holder Assembly. Should a clo arise due to
coffee rinds, it can be cleaned usin a paper clip
or similar tool. Remove K-Cup Holder assembly
and detach Funnel. Insert the paper clip (as shown
in fi . 18) into the Needle to loosen the clo and
push it out. The K-Cup Holder is dishwasher safe.

13
CAUTION: There are sharp needles that puncture the K-Cup abo e the K-
Cup Holder and in the bottom of the K-Cup Holder. To a oid risk of injury,
do not put your fingers in the K-Cup Assembly Housing.
Cleaning the Water eservoir & Water eservoir Lid
The Water Reservoir Lid or Water Reservoir should not be put into the
dishwasher. They should be cleaned with a damp, soapy, non-abrasive cloth
and rinsed thorou hly. Do not dry the inside of the Water Reservoir with a
cloth as lint may remain.
CAUTION: Please r nse the Water Reservo r thoroughly after clean ng to ensure
that no cleaners or clean ng solut ons rema n n th s area as they may contam nate
the water supply n the Brewer.
De-Scaling Your Brewer
Mineral content in water varies from place to place. Dependin on the
mineral content of the water in your area, calcium deposits or scale may
build up in your Brewer. Scale is non-toxic, but left unattended, it can hinder
Brewer performance. De-scalin your Brewer helps maintain the heatin
element and other internal parts of the Brewer that come in contact with
water.
The Brewer should be de-scaled every 3-6 months to ensure optimal
performance. It is possible for calcium deposits to build up faster, makin it
necessary to de-scale more often.
This Brewer is equipped with sensors to
detect when scale buildup is interferin
with the performance of the Brewer.
When this is detected, “DE-SCALE” will
be displayed on the Touch Screen (fi .
19). However, even if “DE-SCALE” is
not displayed, you should continue to
de-scale your Brewer every 3-6 months.
You should promptly de-scale if “DE-
SCALE” is displayed on the Touch
Screen. Properly follow the de-scalin
procedure described.
NOTE: The Brewer w ll cont nue to funct on even when “DE-SCALE” s d splayed.
However, f you do not de-scale soon after t s d splayed; cont nued scale bu ldup
could damage the Brewer. If th s occurs, “DE-SCALE” w ll beg n to bl nk to alert
you to the potent al damage to the Brewer f you do not de-scale mmed ately.
De-Scaling Instructions
A. PREPARE
Step 1: Make sure you have at least 48 ounces of undiluted white vine ar
on hand. You will also need an empty sink and a lar e ceramic mu
(do not use a paper cup).
Step 2: Empty the water in the Water Reservoir.
Step 3: Disable “Auto Off” features.
B. FILL AND CLEAN
Step 1: Pour the vine ar into the Water Reservoir to fill it.
Step 2: Place a lar e mu on the Drip Tray Plate and run a water brew
cycle. DO NOT USE A K-CUP, just select the Lar e Mu brew size.
Pour the contents of the lar e mu into the sink.
Step 3: Repeat the brew process 3 times.
Step 4: Now let the Brewer stand for at least 4 hours while still on.
C. RINSE
Step 1: Ensure the Water Reservoir is filled with fresh water.
Step 2: Place a lar e mu on the Drip Tray Plate and run a water brew
cycle. Pour the contents of the lar e mu into the sink.
Step 3: Repeat brew process until the Water Reservoir is empty.
Step 4: You may need to perform additional water brew cycles if you notice
any residual taste.
NOTE: If “DE-SCALE” s st ll d splayed on the Touch Screen after complet ng the
procedure, repeat the de-scal ng procedure above.
Service
Beyond these recommended cleanin and maintenance procedures this
Brewer is not user serviceable. For service, please refer to the Warranty
section of this uide.
Storage
Empty the Water Reservoir before storin , and take care to ensure that you store your
Brewer in a safe and frost free environment. Please be sure to store your Brewer in its
upri ht position to avoid water leaka e from the inner tank. If you store the Brewer in a
cold environment, you run the risk of water freezin inside the Brewer and causin
dama e. When you prepare to use it after stora e, we recommend rinsin the Water
Reservoir with fresh water and runnin three cleansin brews without a K-Cup.

14
If you plan to move your Brewer to a different location, turn the Brewer off, unplu it,
and empty the Water Reservoir. If your Brewer has been in an environment below
freezin , please be sure to let it warm to room temperature for at least 2 hours before
usin .
Addendum:
This device complies with FCC and Industry Canada RF radiation exposure
limits set forth for eneral population. It should be installed and operated
such that a minimum separation distance of at least 20cm is maintained
between the radiator (antenna) and the user's body, excludin hands and
wrists. This device must not be co-located or operatin in conjunction with
any other antenna or transmitter.
Chan es or modifications not expressly approved by Keuri , Inc. could void
the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a
Class B di ital device, pursuant to Part 15 of the FCC Rules. These limits
are desi ned to provide reasonable protection a ainst harmful interference
in a residential installation. This equipment enerates uses and can radiate
radio frequency ener y and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no uarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turnin the equipment off
and on, the user is encoura ed to try to correct the interference by one of
the followin measures:
- Reorient or relocate the receivin antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with FCC and Industry Canada
RF radiation exposure limits set forth for general
population. It should be installed and operated such
that a minimum separation distance of at least 20cm is
maintained between the radiator antenna) and the
user's body, excluding hands and wrists. This device
must not be co-located or operating in conjunction with
any other antenna or transmitter."
Notes:

15

16
Domestic and International Patents Pendin
60-201114-000 REV B