Keyline MAVIK User manual

ENGLISH
Copyright by Keyline - Italy MAVIK Man. cod. B411026FG Keyline S.p.A. 1
GENERAL INFORMATION AND INSTRUCTIONS
FOR USE
1General Information and Instructions foruse
1.1.0 Keyline MAVIK Remote controls
Keyline MAVIK is a car remote control that guarantee perfect syn-
chronization with the original remote without altering the func-
tionality and working simultaneously.
Keyline MAVIK has a plastic head with four buttons and a replace-
able battery, and is available with many different key blades.
Keyline MAVIK is in compliance with the essential re-
quirements and other relevant provisions of Directive
2014/53/EU.
This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any
interference received including interference that may cause un-
desired operation.
FCC ID: 2ACW2MAVIK
Note: this equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment gener-
ates,uses, and can radiate radio frequency energy and, if
not installed and used in accordance with the instruc-
tions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that
interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio
or television reception, which can be determined by
turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the
following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and
receiver.
• Connect the equipment into an outlet on a circuit dif-
ferent from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV techni-
cian for help.
Important:
RF Exposure: this equipment complies with FCC radia-
tion exposure limits set forth for an uncontrolled
environment.
This equipment is in direct contact with the body of the user un-
der normal operating conditions.This transmitter must not be
co-located or operating in conjunction with any other antenna or
transmitter.
Warning:
Changes or modifications to this equipment not ex-
pressly approved by the party responsible for
compliance could void the user’s authority to operate
the equipment.
1.2.0 Technical features
1.2.1 Environmental conditions
• Temperature limits for transport and storage: from -20°C (-
4°F) to +54°C (+130°F)
• Operating temperature limits: from 5°C (23°F) to +45°C
(+110°F)
1.3.0 Manufacturer's address
Keyline S.p.A.
Via Camillo Bianchi
31015 Conegliano (TV) - ITALY
Tel.: [phone] - Fax: [phone]
Website: www.keyline.it
E-mail: [e-mail]
1.4.0 Caution
•DonotexposetheMAVIK to adverse weather conditions
• Handle the remote control with care during operation
• Avoid accidentally dropping the remote control, which
might be damaged and cease to operate properly
• Keep the key at a temperature between -30 °C and +60 °C.
• If you are in the vicinity of a strong electromagnetic field it
is possible that your key may not work.
Important:
We recommend you replace the battery every 3 years.
(see paragraph on page1).
1.5.0 Replacing the battery
Removing the battery
1. Open the battery compartment using a small flat-blade
screwdriver as lever.
2. Turn the shell upside down, so that the battery falls out
on its own.
Inserting the battery (if the cover is closed)
1. Open the battery compartment as mentioned above.
2. Place the battery CR2032 in the compartment, keeping
the side with + pole upwards.
Width 40 mm
Length 74 mm
Height 19 mm
Battery 3V (Type CR2032)
Antenna frequency 315 MHz US model – 433 MHz EU model

ENGLISH
2KeylineS.p.A. MAVIK Man. cod. B411026FG Copyright by Keyline - Italy
GENERAL INFORMATION AND INSTRUCTIONS
FOR USE
3. Close the compartment cover, by placing the plastic tab on
the long side of the cover in the relevant opening first and
then pressing on the cover until it closes completely.
Warning:
Lithium battery which, when replaced, must be dis-
posed of in the special containers for used batteries.
1.6.0 Replacing the blade
Inserting the blade
1. Press the button to activate the rotation mechanism.
2. Insert the blade in the mechanism, paying attention that
the space reserved for the pin on the blade does NOT face
the rotation mechanism button.
3. Pressing on the blade, turn the rotation mechanism, so
that the hole for the pin is visible.
4. Place the pin on the corresponding hole.
5. Use the pliers to place the pin fully into the hole.
Removing the blade
1. Press the button to activate the rotation mechanism, so
that the hole for the pin is visible.
2. Use the pliers to remove the pin completely from the hole.
3. Remove the blade from the rotation mechanism.