Keysight Technologies N9029BV Service manual

N9029BV
Mini Signal Analyzer Frequency Extension Module
The Keysight N9029BV Mini Signal Analyzer Frequency Extension (Mini SAX) Modules are a smaller version of the
Keysight N9029AVxx SAX modules, and are also manufactured by Virginia Diodes, Inc (VDI).
PRODUCT NOTE

Notices
© Keysight Technologies, Inc. 2021,
2023
No part of this manual may be
reproduced in any form or by any
means (including electronic storage
and retrieval or translation into a
foreign language) without prior
agreement and written consent
from Keysight Technologies, Inc. as
governed by United States and
international copyright laws.
Trademark Acknowledgments
Manual Part Number
N9029-90038
Print Date: June 2023
Supersedes: February 2023
Printed in USA
Published by:
Keysight Technologies
1400 Fountaingrove Parkway Santa
Rosa, CA 95403
Warranty
THE MATERIAL CONTAINED IN
THIS DOCUMENT IS PROVIDED “AS
IS,” AND IS SUBJECT TO BEING
CHANGED, WITHOUT NOTICE, IN
FUTURE EDITIONS. FURTHER, TO
THE MAXIMUM EXTENT PERMITTED
BY APPLICABLE LAW, KEYSIGHT
DISCLAIMS ALL WARRANTIES,
EITHER EXPRESS OR IMPLIED WITH
REGARD TO THIS MANUAL AND
ANY INFORMATION CONTAINED
HEREIN, INCLUDING BUT NOT
LIMITED TO THE IMPLIED
WARRANTIES OF
MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
KEYSIGHT SHALL NOT BE LIABLE
FOR ERRORS OR FOR INCIDENTAL
OR CONSEQUENTIAL DAMAGES IN
CONNECTION WITH THE
FURNISHING, USE, OR
PERFORMANCE OF THIS
DOCUMENT OR ANY INFORMATION
CONTAINED HEREIN. SHOULD
KEYSIGHT AND THE USER HAVE A
SEPARATE WRITTEN AGREEMENT
WITH WARRANTY TERMS
COVERING THE MATERIAL IN THIS
DOCUMENT THAT CONFLICT WITH
THESE TERMS, THE WARRANTY
TERMS IN THE SEPARATE
AGREEMENT WILL CONTROL.
Technology Licenses
The hardware and/or software
described in this document are
furnished under a license and may be
used or copied only in accordance
with the terms of such license.
U.S. Government Rights
The Software is “commercial
computer software,” as defined
by Federal Acquisition Regulation
(“FAR”) 2.101. Pursuant to FAR
12.212 and 27.405-3 and
Department of Defense FAR
Supplement (“DFARS”) 227.7202,
the U.S. government acquires
commercial computer software
under the same terms by which
the software is customarily
provided to the public.
Accordingly, Keysight provides
the Software to U.S. government
customers under its standard
commercial license, which is
embodied in its End User License
Agreement (EULA), a copy of
which can be found at
http://www.keysight.com/find/sweula
The license set forth in the EULA
represents the exclusive authority
by which the U.S. government
may use, modify, distribute, or
disclose the Software. The EULA
and the license set forth therein,
does not require or permit,
among other things, that
Keysight: (1) Furnish technical
information related to
commercial computer software
or commercial computer
software documentation that is
not customarily provided to the
public; or (2) Relinquish to, or
otherwise provide, the
government rights in excess of
these rights customarily provided
to the public to use, modify,
reproduce, release, perform,
display, or disclose commercial
computer software or
commercial computer software
documentation. No additional
government requirements
beyond those set forth in the
EULA shall apply, except to the
extent that those terms, rights, or
licenses are explicitly required
from all providers of commercial
computer software pursuant to
the FAR and the DFARS and are
set forth specifically in writing
elsewhere in the EULA. Keysight
shall be under no obligation to
update, revise or otherwise
modify the Software. With
respect to any technical data as
defined by FAR 2.101, pursuant
to FAR 12.211 and 27.404.2 and
DFARS 227.7102, the U.S.
government acquires no greater
than Limited Rights as defined in
FAR 27.401 or DFAR 227.7103-5
(c), as applicable in any technical
data.
Safety Notices
A CAUTION notice denotes a hazard. It
calls attention to an operating
procedure, practice, or the like that,
if not correctly performed or adhered
to, could result in damage to the
product or loss of important data. Do
not proceed beyond a CAUTION
notice until the indicated conditions
are fully understood and met.
A WARNING notice denotes a hazard.
It calls attention to an operating
procedure, practice, or the like that,
if not correctly performed or adhered
to, could result in personal injury or
death. Do not proceed beyond a
WARNING notice until the indicated
conditions are fully understood and
met.
A NOTE calls the user's attention to
an important point or special
information in the text.

Cable
Mini VDI Module
USB Drive
and Tools
Power Supply and
AC Power Cable
Tr
Keysight Technologies
Mini SAX Modules
Mini Signal Analyzer Frequency Extension Modules
and Accessories
The Keysight N9029BV Mini Signal Analyzer Frequency Extension (Mini SAX) Modules are a smaller version
of the Keysight N9029AVxx SAX modules, and are also manufactured by Virginia Diodes, Inc (VDI). The
modules are for use with Keysight's X-Series EXA, MXA, or PXA spectrum analyzers with external mixer
option EXM recommended for ease of use. See Table 2 on page 5 for available mm-Wave band options.
The modules provide high performance broadband frequency down-conversion, and for modules with
Option UDC, frequency up-conversion. These modules achieve low conversion loss and excellent noise
figure. Refer to the VDI User’s Guide included on the USB drive.
For more information, see the product manual at https://www.vadiodes.com/images/Products/SAX/
SAX_Product_Manual/VDI-731_SAX_Product_Manual.pdf.
Specifications can be found on the VDI website at https://www.vadiodes.com/images/Products/SAX/
VDI_Mini_SAX_Specifications_2021.12.29.pdf.
The cables and power supply will be included with the module in the transport case. Cutouts have been
created for the accessories within the transpor t case.
ansport Case
Accessories
(Optional)
1. To order accessories, see Accessories and Information on page 10. For the Keysight Millimeter Wave Frequency
Extenders Technical Overview document, visit http://literature.cdn.keysight.com/litweb/pdf/5991-3161EN.pdf
1.
Keysight N9029-90038
3

Power Requirements
•Voltage and/or range (V): 100-240 Vac (AC input for AC/DC adapter), 9 Vdc (input
for module)
•Frequency and/or range (Hz): 50-60 Hz (AC input for AC/DC adapter)
•Power in Watts, VA or Current (A): 1.2 A max (input for AC/DC adapter), 4 A (input
for module)
The instrument can operate with mains supply voltage fluctuations up to
± 10% of the nominal voltage.
Environmental Conditions
•For indoor use only
This product is designed for use in INSTALLATION CATEGORY II and
POLLUTION DEGREE 2.
Install the instrument so that the detachable power cord is readily identifiable and is
easily reached by the operator. The detachable power cord is the instrument
disconnecting device. It disconnects the mains circuits from the mains supply before
other parts of the instrument. Alternatively, an externally installed switch or circuit
breaker (which is readily identifiable and is easily reached by the operator) may be
used as a disconnecting device.
Before using your SAX module, please read all documentation from VDI
(included on the USB drive).
Be aware of the power level applied to the waveguide input. Non-warrantied
damage to the internal mixer can occur if the power level is at or above the
damage level specified in the VDI User's Guide for "RF Input."
4
Keysight N9029-90038
Table 1 Dimensions
Height 1.50 inches
Width 5.25 inches
Length 3.50 inches
Physical Characteristics
An external attenuator is recommended when using N9029BV Mini-SAX with
the EXM option to avoid exceeding the damage input LO power (16 dBm).

Typical Connection Diagram for External Mixing
Table 2 SAX Mini Modules
Keysight
Model Number
VDI
Model Number
Frequency
(GHz)
N9029BV-W02 WR2.2 (WM-570) Mini SAX 330 to 500
N9029BV-W03 WR3.4 Mini SAX 220 to 330
N9029BV-W05 WR5.1 Mini SAX 140 to 220
N9029BV-W06 WR6.5 Mini SAX 110 to 170
The product serial number is the OEM serial number SAXxxxx (xxxx =
numbers in the OEM serial number) assigned by Virginia Diodes, Inc.
Refer to the label on the product for the serial number.
Table 3 Mini SAX Options
Option Description
UDC Adds IF input data (on USB) for frequency up-conversion
1GD Adds data (on USB) at 1 GHz spacing
Keysight N9029-90038
5
N9029BV-W04 WR4.3 Mini SAX 170 to 260
N9029BV-W1B WR1.5 (WM-380) Mini SAX 500 to 750
N9029BV-W08 WR8.0 Mini SAX 90 to 140
N9029BV-W10 WR10 Mini SAX 75 to 110
N9029BV-W12 WR12 Mini SAX 60 to 90
N9029BV-W15 WR15 Mini SAX 50 to 75
N9029BV-W19 WR19 Mini SAX 40 to 60
N9029BV-W28 WR28 Mini SAX 26.5 to 40
N9029BV-W01WR1.0 (WM-250) Mini SAX 750 to 1100

SAX Label
There is data on the USB drive that can be used to create a corrections file to improve amplitude
accuracy.
Always use the information printed on the SAX label of your module.
When using the LO/IF (L) Input (External Mixing), use LO (L): N= X, with
"X" being the multiplication factor value shown on your SAX label.
When using the LO/IF (H) Input, use LO (H): N= X, with "X" being the
multiplication factor value shown on your SAX label.
On the SAX label, the multiplication
factor values are circled. This is an
example only; the actual values will
vary.
•
•
When using your signal analyzer with the SAX, you must set the analyzer to external mixing, including
harmonic and Doubler Switched parameters.
For the N90x0A Models:
[Input/Output] > External Mixer > External Mixer > Ext Mix Setup > Edit Harmonic Table >
[Enter] (or select OK).
Table Type > Doubler Switching > Harmonic > [N] > Enter N value (see SAX label on module, or see VDI
document, for N value)
For the N90x0B Models:
[Input/Output] > Select Input > External Mixer > External Mixer Setup > Table Type > Doubler Switching
>Harmonic (under Harmonic Table) > Enter N value (see SAX label on module, or see VDI document, for
N value)
For improved spurious response:
Change the number of sweep points:
[Sweep/Control] > Points > [40001]
Multi-Touch Sweep > Sweep Config > Points > [40001]
Reduce resolution bandwidth:
[BW] > Res BW > [300 kHz]
Turn on Signal ID:
[Input/Output] > External Mixer > Signal ID > On > Signal ID Mode > Image Suppress
Multi-Touch Input > Output > Signal ID > On > Signal ID Mode > Image Suppress
•
•
•
6
Keysight N9029-90038

Frequency Up-Converter Operation
The option UDC has an IF input and 9 volt connections for external devices. For frequency
up-conversion, the left jumper is to be removed.
The IF input frequency will be up-converted to the multiplication factor of the LO input (H) ++
IF input {N x LO input (H) + IF input = waveguide output frequency}. Refer to the VDI
User's Guide for frequencies and power levels.
1. Connect RF source to LO input (H), such as an E8257D PSG.
2. Connect RF signal to be up-converted to the IF input, such as an E8257D PSG.
Voltage Bias
Port
Other modes of operation may be found in the VDI documentation.
Keysight N9029-90038
7
LO/IF Input
IF Input

Use ESD precautions when using these devices. The IF port for CCDs has
ESD protection, but the IF port for CCUs is extremely ESD sensitive. Do not
apply any DC biases or surges when connecting or disconnecting from the
IF port. Discharge static from cables befor connecting to the device.
Replace the IF with provided 50 Ω termination when IF port is not in use.
Observe the power level you are applying to the LO, IF, and RF
waveguide input ports. Damage will occur if it is not observed.
Before using your converter module, please read all documentation from
VDI (included on the USB drive). It is important to follow the General
Operating Procedures and Guidelines section.
This product has been designed and tested in accordance with accepted
industry standards and has been supplied in a safe condition. The
documentation contains information and warnings that must be followed
by the user to ensure safe operation and to maintain the product in a safe
condition.
Safety and Information
Only Keysight approved accessories shall be used.
Use the Keysight supplied power cord or one with the same or better
electrical rating.
No operator serviceable parts inside. Refer servicing to qualified
personnel. To prevent electrical shock do not remove covers.
The Mains wiring and connectors shall be compatible with the
connector used in the premise electrical system. Failure to ensure
adequate earth grounding by not using the correct components may
cause product damage and serious injury.
This instrument has auto-ranging line voltage input. Be sure the
supply voltage is within the specified range and voltage fluctuations
do not to exceed 10 percent of the nominal supply voltage.
The main power cord can be used as the system disconnecting device. It
disconnects the mains circuits from the mains supply.
If this product is not used as specified, the protection provided by the
equipment could be impaired. This product must be used in a normal
condition (in which all means for protection are intact) only.
8
Keysight N9029-90038

Instrument Markings
Listed below are definitions for the markings that may be found on the product.
IP 2 0
The instruction documentation symbol. The product is marked with this symbol when it is
necessary for the user to refer to the instructions in the documentation.
The AC symbol indicates the required nature of the line module input power.
This symbol indicates separate collection for electrical and electronic equipment,
mandated under EU law as of August 13, 2005. All electric and electronic equipment are
required to be separated from normal waste for disposal (Reference WEEE Directive,
2002/96/EC).
This symbol indicates that the power line switch is ON.
This symbol indicates that the power line switch is in the OFF position.
The instrument has been designed to meet the requirements of IP 2 0 for egress and
operational environment.
The RCM mark is a registered trademark of the Australian Communications and Media
Authority.
Indicates the time period during which no hazardous or toxic substance elements are
expected to leak or deteriorate during normal use. Forty years is the expected useful life
of the product.
The CE mark is a registered trademark of the European Community.
The Keysight email address s required by EU directives applicable to our product.
This is a symbol of an Industrial Scientific and Medical Group 1 Class A product (CISPR
11, Clause 5).
This is a marking to indicate product compliance with the Canadian Interference-Causing
Equipment Standard (ICES-001). Cet appareil ISM est conforme à la norme NMB du
Canada.
This symbol on all primary and secondary packaging indicates compliance to China
standard GB 18455-2001.
South Korean Certification (KC) mark; includes the marking's identifier code which
follows this format: MSIP-REM-YYY-ZZZZZZZZZZZZZZ.
[email protected]
•IEC/EN 61326-1
•CISPR Pub 11 Group 1, Class A
•AS/NZS CISPR 11
•CAN ICES/NMB-001(A)
This ISM device complies with Canadian ICES-001.
Cet appareil ISM est conforme a la norme NMB-001 du Canada.
ICES/NMB-001
Safety
Complies with the essential requirements of the European Low Voltage Directive.
EMC
Complies with the essential requirements of the European EMC Directive as well as current editions of the
following standards (dates editions are cited in VDI's Declaration of Conformity):
Keysight N9029-90038
9

Contacting Keysight
Keysight Technologies does not guarantee the performance of the VDI modules, or system
performance. However, if warranty or repair is needed Keysight will provide full support to our
customer.
Inspect the shipping container. If the container or packing material is damaged, it should be
kept until the contents of the shipment have been checked mechanically and electrically. If
there is mechanical damage or if the instrument does not pass the performance tests, notify
the nearest Keysight Technologies office. Keep the damaged shipping materials (if any) for
inspection by the carrier and a Keysight Technologies representative.
Assistance with test and measurement needs, and information on finding a local Keysight office
are available on the Internet at:
http://www.keysight.com/find/assist
You can also purchase accessories or find documentation items on the Internet at:
http://www.keysight.com/find
If you do not have access to the Internet, contact your field engineer.
In any correspondence or telephone conversation, refer to the Keysight
product by its model number and full serial number. With this information,
the Keysight representative can determine the warranty status of your unit.
10
Keysight N9029-90038
Accessories and Information
A list of accessories for the N9029BV Mini SAX Modules can be found on the
N9029AV99 Waveguide Accessories for mm-Wave Product Note (N9029-90035) at:
https://www.keysight.com/us/en/assets/9921-01743/user-manuals/N9029AV99-
Millimeter-Waveguide-Accessories-Product-Note.pdf.
For information concerning the operation and connections, reference the VDI User Guide
(included on the USB Drive), or the Keysight X-Series Signal Analyzer's documentation by
searching http://www.keysight.com/find/pxa_manuals. You may also reference the X-Series
Signal Analyzer On-line Help System for operational information.
For more information, visit the Virginia Diodes, Inc. website at:
https://www.vadiodes.com/en/products/signal-analyzer

ome
ed User’s Guide that can be
eg 9pt/14pt-leading)
OR SIT AMET CONSECTETUR
eg 12pt/16pt-leading)
This information is subject to change
without notice.
© Keysight Technologies 2021, 2023
Print Date: June 2023
Supersedes: February 2023
www.keysight.com