M-system R30US2 User manual

5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9017 Rev.2 P. 1 / 5
INSTRUCTION MANUAL
UNIVERSAL INPUT MODULE
(2 points, isolated) MODEL R30US2
BEFORE USE ....
Thank you for choosing M-System. Before use, please check
contents of the package you received as outlined below.
If you have any problems or questions with the product,
please contact M-System’s Sales Office or representatives.
■PACKAGE INCLUDES:
Universal input module (body + CJC sensor × 2)..............(1)
■MODEL NO.
Confirm Model No. marking on the product to be exactly
what you ordered.
■INSTRUCTION MANUAL
This manual describes necessary points of caution when
you use this product, including installation, connection and
basic maintenance procedures.
POINTS OF CAUTION
■CONFORMITY WITH EU DIRECTIVES
• The equipment must be mounted inside the instrument
panel of a metal enclosure.
• The actual installation environments such as panel con-
figurations, connected devices, connected wires, may af-
fect the protection level of this unit when it is integrated
in a panel system. The user may have to review the CE
requirements in regard to the whole system and employ
additional protective measures to ensure the CE conform-
ity.
■GENERAL PRECAUTIONS
• Before you remove the terminal block or mount it, turn off
input signals for safety.
■HOT SWAPPABLE MODULES
• It is possible to replace a module with the power supplied
provided that the module is replaced with one with the
same model number and installed in the same base slot.
• Turn off input signals before replacing the module for
safety. Note that replacing multiple modules at once may
greatly change line voltage levels. We highly recommend
to replace them one by one.
■UNUSED CHANNEL
• Set unused channels to “CH disabled” with PC Configura-
tor software (model: R30CFG). Otherwise, unused chan-
nels left open are to be burnout status, setting a data er-
ror at the PLC or other host devices.
■ENVIRONMENT
• Indoor use.
• When heavy dust or metal particles are present in the
air, install the unit inside proper housing with sufficient
ventilation.
• Do not install the unit where it is subjected to continuous
vibration. Do not subject the unit to physical impact.
• Environmental temperature must be within -10 to +55°C
(14 to 131°F) with relative humidity within 10 to 90% RH
in order to ensure adequate life span and operation.
■WIRING
• Do not install cables close to noise sources (relay drive
cable, high frequency line, etc.).
• Do not bind these cables together with those in which
noises are present. Do not install them in the same duct.
• Be sure to attach the terminal cover for safety.
■AND ....
• The unit is designed to function as soon as power is sup-
plied, however, a warm up for 10 minutes is required for
satisfying complete performance described in the data
sheet.

R30US2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9017 Rev.2 P. 2 / 5
COMPONENT IDENTIFICATION
RUN
ERR
CJC Sensor
(CJM × 2)
11
13
■FRONT VIEW
■BOTTOM VIEW
■SIDE VIEW
Specifications
Positioning Guide
Terminal Cover
Lock Tab
Base Fixing Screw
RUN LED
Input Terminal Block
ERR LED
Terminal Fixing Screw
1
2
3
4
5
6
10
20
9
7
8
19
18
17
16
15
14
12
■STATUS INDICATOR LED
ID COLOR FUNCTION
RUN Green ON while network module operates normally
OFF in network module error
ERR Red OFF when input circuit and internal bus operate normally
Blinks in 1 sec. cycles when burnout is detected or with input value error (≤ -15%, ≥ +115%, becomes less
than the lower limit or exceeds the upper limit of usable range).
Blinks in 400 msec. cycles with input circuit error (AD converter response failure).
ON with internal bus error
■TERMINAL ASSIGNMENT
11
U13
12
U14
13
U23
14
U24
15
NC
16
NC
17
NC
18
NC
19
NC
20
NC
1
U11
2
U12
3
U21
4
U22
5
NC
6
NC
7
NC
8
NC
9
NC
10
NC
No. ID
FUNCTION
Wide Span Voltage
Range / Current
Narrow Span
Voltage Range T/C
RTD / Resistor
(3-wire)
RTD / Resistor
(2-wire)
Potentiometer
1 U11 Wide Span volt. range / Current 1 – – – – –
2 U12 –
Narrow Span volt. range 1 T/C 1 RTD 1-b – Input S1
3 U21
Wide Span volt. range / Current 2 – – – – –
4 U22 –
Narrow Span volt. range 2 T/C 2 RTD 2-b – Input S2
5 NC No connection
6 NC No connection
7 NC No connection
8 NC No connection
9 NC No connection
10 NC No connection
11 U13 – – CJM1 RTD 1-B RTD 1-B Input L1
12 U14 Common 1 Common 1
COM 1 RTD 1-A RTD 1-A Input H1
13 U23 – – CJM2 RTD 2-B RTD 2-B Input L2
14 U24 Common 2 Common 2
COM 2 RTD 2-A RTD 2-A Input H2
15 NC No connection
16 NC No connection
17 NC No connection
18 NC No connection
19 NC No connection
20 NC No connection

R30US2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9017 Rev.2 P. 3 / 5
INSTALLATION
■INSTALLATION TO THE BASE
Use the Installation Base (model: R30BS).
The I/O slots are numbered in the ascending order starting
from the one on the immediate right side of the network
module (slot 1, slot 2...).
A code indicating the I/O slot number is assigned to each
I/O slot and I/O data is allocated in the order of this codes.
When an I/O slot is vacant, blank data is sent or received to/
from the PLC, etc.
PWR COM I/O1 I/O n
■HOW TO MOUNT THE MODULE
1) Engage the positioning guide of the module with the In-
stallation Base.
2) Pivot the module on the positioning guide and press it
down until the lock tab clicks into place.
Positioning Guide
3) Tighten the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more) (torque 0.5 N·m).
Base Fixing Screw
■HOW TO REMOVE THE MODULE
1) Loosen the base fixing screw using a screwdriver (stem
length: 70 mm/2.76” or more).
Base Fixing Screw
2) While pressing the projection on the lock tab, push the
module upward.
3) Detach the positioning guide of the module from the In-
stallation Base.
Lock Tab

R30US2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9017 Rev.2 P. 4 / 5
TERMINAL CONNECTIONS
Connect the unit as in the diagram below.
For thermocouple input, attach the CJC sensor together with input wining to the input screw terminals.
■EXTERNAL DIMENSIONS unit : mm (inch)
11
13
110 (4.33)
25 (.98) 98 (3.86)
20–M3
SCREW
6
(.24)
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
12
■CONNECTION DIAGRAM
1
2
11
12
U11
U12
3
4
13
14
U21
U22
U13
U14
U24
U23
INTERNAL POWER
INTERNAL BUS
BUS CONNECTOR
Input 1
Input 2
• DC Voltage (-10 – +10V)
• DC Current (-20 – +20mA)
■ UNIVERSAL INPUT CONNECTION
• Thermocouple
CJC
Sensor
+
––
A
B
B
A
B
max.
min.
+
−
Un1
Un3
Un4
Un2
Un1
Un3
Un4
Un2
Un1
Un3
Un4
Un2
Un1
Un3
Un4
Un2
INPUT
+
−
INPUT
+
−
Un1
Un3
Un4
Un2
Un1
Un3
Un4
Un2
• DC Voltage (-1000 – +1000mV)
• RTD or Resistor (3-wire) • RTD or Resistor (2-wire) • Potentiometer

R30US2
5-2-55, Minamitsumori, Nishinari-ku, Osaka 557-0063 JAPAN
Phone: [phone] Fax: [phone] E-mail: [e-mail]
EM-9017 Rev.2 P. 5 / 5
WIRING INSTRUCTIONS
■TIGHTENING TORQUE
Separable screw terminal wiring screw: 0.5 N·m
Separable screw terminal fixing screw: 0.5 N·m
■SOLDERLESS TERMINAL unit: mm (inch)
Refer to the drawing below for recommended ring tongue
terminal size. Spade tongue type is also applicable. Solder-
less terminals with insulation sleeve do not fit.
Applicable wire size: 0.25 to 0.75 mm2
Recommended manufacturer: Japan Solderless Terminal
MFG. Co., Ltd., Nichifu Co., Ltd.
3.2 (.13) dia.
12 (.47) max.
6 max.
(.24)
3 (.12) max.
■HOW TO REMOVE SEPARABLE SCREW TERMINAL
The terminal block is separable in two pieces. Evenly loos-
en two screws on top and bottom of the terminal block to
separate.
■HOW TO ATTACH CJC SENSOR
In re-attaching once removed CJC sensor, connect it to ter-
minals Un3 and Un4 as shown below.
A RTD is attached on the REAR surface of the CJC sensor.
In order to measure accurate reference junction tempera-
ture, be sure to connect the sensor to terminal Un4 with its
upside FRONT surface.
Un3 Un4
CJC sensor
REAR surface
RTD
FRONT surface
PC CONFIGURATOR
The following parameter items can be set with using PC
Configurator Software (model: R30CFG).
Refer to the users manual for the R30CFG for detailed op-
eration of the software program.
■CHANNEL INDIVIDUAL SETTING
PARAMETER SETTING RANGE DEFAULT
SETTING
Unused setting CH enabled
CH disabled
CH enabled
Input type -10 – +10 V DC
-1000 – +1000 mV DC
-20 – +20 mA DC
POT 0 – 4000 Ohm
POT 0 – 2500 Ohm
POT 0 – 1200 Ohm
POT 0 – 600 Ohm
POT 0 – 300 Ohm
POT 0 – 150 Ohm
OHM 0 – 4000 Ohm
RTD Pt 100
RTD Pt 500
RTD Pt 1000
RTD Pt 50 Ω
RTD JPt 100
RTD Ni 508.4 Ω
RTD Cu 10
TC (PR)
TC K
TC E
TC J
TC T
TC B
TC R
TC S
TC C
TC N
TC U
TC L
TC P
-10 – +10 V DC
Wiring 2-wire
3-wire
–
Burnout Upscale
Downscale
None
–
CJC Enabled
Disabled
–
Unit degC
degF
K
–
Fine zero adjustment -320.00 – +320.00 (%) 0.00 (%)
Fine gain adjustment -3.2000 – +3.2000 1.0000
Zero base
depends on input types*
1
-10.000 V DC
Full base
depends on input types*
1
10.000 V DC
Scaled range Zero -32 000 – +32 000 0
Scaled range Span -32 000 – [phone]
First order lag filter 0.0, 0.5 – 60.0 sec. 0.0 sec.
*1. For details, refer to the users manual of R30CFG.