Keysight Technologies M9485A User guide

Startup Guide
Keysight M9485A PXIe
Multiport Vector Network
Analyzer
M9300A, Frequency Reference
M9389A, PXIe Vector Network Analyzer Source
M9309A, PXIe Vector Network Analyzer Synthesizer
M9340A, PXIe Vector Network Analyzer RF Distributor
M9376A, PXIe Vector Network Analyzer Receiver
M9377A, PXIe Vector Network Analyzer Direct Access Receiver
M9378A/B, PXIe Vector Network Analyzer Directional Coupler

Notices
© Keysight Technologies, Inc.
2015-2016
No part of this manual may be
reproduced in any form or by any
means (including electronic storage
and retrieval or translation into a
foreign language) without prior
agreement and written consent from
Keysight Technologies, Inc. as
governed by United States and
international copyright laws.
Trademark Acknowledgments
Manual Part Number
M9485-90020
Print Date
November, 2016
Published in Malaysia
Published by
Keysight Technologies
International Japan G.K,
1-3-3 Higashikawasaki-cho
Chuo-ku
Kobe-shi, Hyogo, Japan
Warranty
THE MATERIAL CONTAINED IN THIS
DOCUMENT IS PROVIDED “AS IS,”
AND IS SUBJECT TO BEING
CHANGED, WITHOUT NOTICE, IN
FUTUREEDITIONS.FURTHER,TOTHE
MAXIMUM EXTENT PERMITTED BY
APPLICABLE LAW, KEYSIGHT
DISCLAIMS ALL WARRANTIES,
EITHER EXPRESS OR IMPLIED WITH
REGARD TO THIS MANUAL AND ANY
INFORMATION CONTAINED HEREIN,
INCLUDINGBUTNOTLIMITEDTOTHE
IMPLIED WARRANTIES OF
MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE.
KEYSIGHTSHALL NOT BE LIABLEFOR
ERRORS OR FOR INCIDENTAL OR
CONSEQUENTIAL DAMAGES IN
CONNECTION WITH THE
FURNISHING, USE, OR
PERFORMANCE OF THIS DOCUMENT
OR ANY INFORMATION CONTAINED
HEREIN.SHOULDKEYSIGHTANDTHE
USER HAVE A SEPARATE WRITTEN
AGREEMENT WITH WARRANTY
TERMS COVERING THE MATERIAL IN
THIS DOCUMENT THAT CONFLICT
WITHTHESETERMS,THEWARRANTY
TERMS IN THE SEPARATE
AGREEMENT WILL CONTROL.
Technology Licenses
The hardware and/or software
described in this document are
furnished under a license and may be
used or copied only in accordance
with the terms of such license.
Restricted Rights Legend
If software is for use in the
performance of a U.S. Government
prime contract or subcontract,
Software is delivered and licensed as
“Commercial computer software” as
defined in DFAR 252.227-7014 (June
1995), or as a “commercial item” as
defined in FAR 2.101(a) or as
“Restricted computer software” as
definedinFAR52.227-19(June1987)
oranyequivalentagencyregulationor
contract clause. Use, duplication or
disclosure of Software is subject to
Keysight Technologies’ standard
commercial license terms, and
non-DOD Departments and Agencies
oftheU.S.Governmentwillreceiveno
greater than Restricted Rights as
defined in FAR 52.227-19(c)(1-2)
(June 1987). U.S. Government users
will receive no greater than Limited
Rights as defined in FAR 52.227-14
(June 1987) or DFAR 252.227-7015
(b)(2)(November1995),asapplicable
in any technical data.
Safety Notices
CAUTION
ACAUTIONnoticedenotesahazard.It
calls attention to an operating
procedure,practice,orthe like that, if
notcorrectlyperformedoradheredto,
couldresultindamage to theproduct
or loss of important data. Do not
proceed beyond a CAUTION notice
untiltheindicatedconditionsarefully
understood and met.
WARNING
A WARNING notice denotes ahazard.
It calls attention to an operating
procedure,practice,orthe like that, if
notcorrectlyperformedoradheredto,
could result in personal injury or
death. Do not proceed beyond a
WARNING notice until the indicated
conditions are fully understood and
met.

Contents
3
1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Getting Started
Introduction 5
Related Documentation 5
STEP 1. Unpack and Inspect the Network Analyzer Modules 6
Inspect for Damage 7
How to Return an Instrument for Service 7
STEP 2. Check the Shipment 8
STEP 3. Install the Network Analyzer Modules 9
Recommended Best Practices to Ensure Proper and Safe Module Operating
Conditions 9
Tools Required for the Installation Procedure 9
Installation Procedure 10
STEP 4. Install the Software 37
System Requirements 37
Hardware Requirements 37
Power Up the Controller 38
Software Installation Overview 38
STEP 5. Verify Operation of the Network Analyzer Modules 41
Execute the M9385A Soft Front Panel Application 41
The Operator’s Check 41
Port Configuration/System Power Calibration 41
2 . . . . . . . . . . . . . . . . . . . Getting Help with Your Network Analyzer Module
Help System 43
Contacting Keysight 44

4
Contents

5
Getting Started
Introduction
M9485A PXIe Startup Guide
1 Getting Started
Introduction
The M9485A PXIe vector Network Analyzer consists of M9300A (Frequency
Reference), M9309A (Synthesizer), M9389A (Source Output), M9340A
(Distributors), M9376A (VNA Receiver), M9377A (Direct Access Receiver) and
M9378A/B (Directional Coupler). M9389A includes M9309A and M9310A.
You may add as many receivers as you require and have n-port Network
Analyzers up to 24-ports, according to the number of receiver modules. Each
module can be controlled with the M9485A Soft Front Panel and remote
commands (IVI, SCPI). This allows you to make the network analyzer
measurement just as the n-port Network Analyzer.
The scope of this Startup Guide is to detail the processes of receiving and
installing the network analyzer module and cables that compose the Keysight
M9485A PXIe Vector Network Analyzer modules. Additionally, installing the
required software and verifying network analyzer module operation is
documented. If you have any questions after reviewing this information, please
contact your local Keysight Technologies Inc. representative or contact us
through our support Website at http://www.keysight.com/support.
Related Documentation
You can find all M9485A PXIe network analyzer module documentation and
other resources at: http://www.keysight.com/find/m9485A 
or at the respective product pages on www.keysight.com (go to Document
Library > Manuals).

6
Getting Started
STEP 1. Unpack and Inspect the Network Analyzer Modules
STEP 1. Unpack and Inspect the Network Analyzer Modules
CAUTION Thenetworkanalyzermodulesareshippedinmaterialswhichpreventdamagefromstatic.
The modules should only be removed fromthe packaging in an anti-static area ensuring
that correct anti-static precautions aretaken. Store all modules in anti-static envelopes
when not in use.
Electrostatic discharge (ESD) can damage or destroy electronic components.
Use a static-safe work station to perform all work on electronic assemblies.
Figure 1-1 shows a static-safe work station using two types of ESD protection:
conductive table-mat and wrist-strap combination, and conductive floor-mat
and heel-strap combination. Both types, when used together, provide a
significant level of ESD protection. Of the two, only the table-mat and
wrist-strap combination provides adequate ESD protection when used alone.
To ensure user safety, the static-safe accessories must provide at least 1
meg-ohm of isolation from ground.
WARNING DoNOT usethese techniquesfora static-safeworkstation whenworkingoncircuitrywith
a voltage potential greater than 500 volts.
Figure 1-1 ESD protection setup

7
Getting Started
STEP 1. Unpack and Inspect the Network Analyzer Modules
Unpack the network analyzer modules from the shipping containers. Keep the
black plastic port protector and the shipping containers for possible reuse.
Inspect for Damage
After unpacking a network analyzer module, inspect it for any shipping
damage. Report any damage to the shipping agent immediately, as such
damage is not covered by the warranty.
CAUTION To avoid damage when handling the network analyzer modules, do not touch exposed
connector pins.
How to Return an Instrument for Service
Should it become necessary to return a network analyzer module for repair or
service, follow the steps below:
1. Review the warranty information shipped with your product.
2. Contact Keysight to obtain a Return Material Authorization (RMA) and
return address. For assistance finding Keysight contact information, go to
www.keysight.com/find/assist (worldwide contact information for repair
and service).
3. Write the following information on a tag and attach it to the network
analyzer module:
• Name and address of owner. A P.O. box is not acceptable as a return
address.
• Network analyzer module serial numbers. The serial number label is
located on the side panel of the module. The serial number can also be
read from the Soft Front Panel (SFP) interface, after the hardware is
installed.
• Description of the service required or the failure.
4. On the shipping label, write ATTENTION REPAIR DEPARTMENT and the
RMA number.
5. Ship the analyzer module using the original packaging materials. Shipping
the analyzer module in anything other than the original packaging may
result in non-warranted damage.
NOTE In your correspondence, refer to the network analyzer module by serial number and by
model number.

8
Getting Started
STEP 2. Check the Shipment
STEP 2. Check the Shipment
The M9485A consists of several modules, cables and dividers. Use the
Contents List in the shipping container to verify the completeness of your
shipment. If not complete, refer to “Contacting Keysight” on page 44.

9
Getting Started
STEP 3. Install the Network Analyzer Modules
STEP 3. Install the Network Analyzer Modules
NOTE These modules can be used in a chassis with a PXIe, or PXI-H chassis slots.
Recommended Best Practices to Ensure Proper and Safe Module Operating
Conditions
• Ensure proper chassis air flow is maintained.
• The use of a Keysight M9018A chassis is recommended for optimum
temperature control. If a different chassis is used, make sure it provides
thermal protection if fans become inoperable or forced air cooling is
obstructed.
— If using the Keysight M9018A PCIe Cable Interface, download the
Keysight Multiple PXIe and AXIe Chassis System Configuration Tool.
Save the file to your local hard drive; do not try to open the file from the
Internet location.
• Use slot blockers and EMC filler panels in empty module slots to ensure
proper operating temperatures. Keysight chassis and slot blockers optimize
module temperature performance and reliability of test.
• Set chassis fans to high or auto. Do not disable fans.
• Position chassis to allow plenty of space around chassis air intake and fan
exhaust.
• At ambient temperatures above 45° C (113° F) set the chassis fan to high.
Figure 1-2 M9485A chassis air flow
Tools Required for the Installation Procedure
• Phillips #1 torque driver, set to 4 in-lb (0.45 N.m) - not supplied.

10
Getting Started
STEP 3. Install the Network Analyzer Modules
• Socket adapter (part number M9485-23001) - supplied.
• Torque driver (for use with socket adapter), set to 8 in-lb (0.91 N.m) - not
supplied.
• Cable removal tool (part number 5002-3361) - supplied.
• Torque Wrench for SMA, set to 8 in-lb (0.91 N.m) - not supplied.
• 5.5 mm open end wrench - not supplied.
Installation Procedure
CAUTION PXI hardware does not support “hot-swap” (changing network analyzer modules while
power is applied to the chassis) capabilities. Before installing or removing a module
to/from thechassis, power-off the chassis to prevent damage to the module.
1. Make sure that the line cord is plugged in to establish earth ground and that
the chassis power switch is Off (see callouts 1 and 3 in Figure 1-3 on
page 11).
2. Wear a grounded wrist strap for this procedure (see callout 2 in Figure 1-3
on page 11).
3. If the chassis has multiple fan speed settings, ensure that the fan switch is
set to high or auto.
4. Position the chassis to provide ample space between the chassis fan intake
and exhaust vents. Blockage by walls or obstructions affects the air flow
needed for cooling. (Refer to the chassis documentation for more
information about cooling.)
5. Before inserting the network analyzer module into the chassis, back-out the
top mounting screw (see callout 7 in Figure 1-3 on page 11) on the module
to ensure that there is no interference between the screws and the
mounting rails.
6. Holding the module by the injector/ejector handle, slide it into a slot, as
shown in callouts 4 – 6 in Figure 1-3 on page 11.
a. Install the module into the slot of the chassis by placing the module card
edges into the front module guides (top and bottom).
The network analyzer module can be installed in any PXIe or hybrid PXI
slot marked with a peripheral slot compatibility image (solid black
circle fro PXIe, or solid black circle with the letter “H” for hybrid.