Keysight x series Quick start guide

N9032B
IQ Streaming
Option ST1 and ST2
Keysight X-Series Signal Analyzer
INSTALLATION NOTE

Notices
© Copyright 2023 Keysight Technologies, Inc.
The information contained in this document is subject to change without notice.
Keysight Technologies makes no warranty of any kind with regard to this material, including but
not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Keysight Technologies shall not be liable for errors contained herein or for incidental or
consequential damages in connection with the furnishing, performance, or use of this material.
Manual Part Number
N9032-90010
Edition
Edition 1, May 2023
Supersedes: None
Printed in USA
Published by:
Keysight Technologies, Inc.
1400 Fountaingrove Parkway
Santa Rosa, CA 95403

Installation Note N9032-90010 3
Option ST1 and ST2 – IQ Streaming
Option ST1 and ST2 – IQ Streaming
This document provides detailed instructions for the installation of the IQ Streaming upgrades
for the N9032B PXA Signal Analyzer with Option 544/550, or Option 508/513/526, with serial
prefix ≥MY/SG6319.
Please be sure to read this entire document before attempting to perform this upgrade. Then, be
sure to perform the steps in this procedure in the order that they are listed so that the installation
will complete properly, and the instrument will function as desired when completed.
Compatibility
This instrument option requires that the instrument has firmware version A.34.00 or newer. If the
instrument being upgraded does not currently meet this requirement the following procedure
includes a step to update it.
Instrument Calibration
The validity of any existing calibration that the instrument being upgraded may have will not be
affected by the installation of this upgrade.
Products Affected: PXA N9032B
Option 544/550 all serial prefix
Option 508/513/526 serial prefix ≥MY/SG6319
To Be Performed By: (X) Keysight Service Center
( ) Advanced User
()User
Estimated Installation Time:
Estimated Adjustment Time:
Estimated Verification Time:
2.0 Hours
0.0 Hours
1.0 Hours

4Installation Note N9032-90010
Option ST1 and ST2 – IQ Streaming
What you will find in this document
ESD Information............................................................................................................ page 5
Upgrade Contents......................................................................................................... page 7
Tools Required............................................................................................................... page 8
Initial Instrument Functionality Check ........................................................................ page 8
Instrument Software Revision Check .......................................................................... page 8
Upgrade Instructions.................................................................................................... page 9
Hardware Disassembly............................................................................................ page 9
ODI Cable Installation........................................................................................... page 13
Hardware Assembly.............................................................................................. page 20
Instrument Button Up .......................................................................................... page 24
Rear Panel Labels ................................................................................................. page 27
Instrument Software Installation ......................................................................... page 28
License Key Retrieval and Installation ................................................................ page 28
Adjustments and Performance Verification.............................................................. page 29
Manual Procedures Required............................................................................... page 29
Automated Utilities Required............................................................................... page 29
Automated Adjustments Required ...................................................................... page 29
Automated Performance Testing Required ......................................................... page 29
ODI Loopback Test..................................................................................................... page 30

Installation Note N9032-90010 5
Option ST1 and ST2 – IQ Streaming
ESD Information
Protection from Electrostatic Discharge
Electrostatic discharge (ESD) can damage or destroy electronic components. All work on electronic
assemblies should be performed at a static-safe workstation. Figure 1 shows an example of a
static-safe workstation using two types of ESD protection:
— Conductive table-mat and wrist-strap combination.
— Conductive floor-mat and heel-strap combination.
Both types, when used together, provide a significant level of ESD protection. Of the two, only the
table-mat and wrist-strap combination provides adequate ESD protection when used alone. To
ensure user safety, the static-safe accessories must provide at least 1 megohm of isolation from
ground.
Figure 1 Example of a Static-Safe Workstation
These techniques for a static-safe workstation should not be used when working on circuitry
with a voltage potential greater than 500 volts.

6Installation Note N9032-90010
Option ST1 and ST2 – IQ Streaming
Handling of Electronic Components and ESD
The possibility of unseen damage caused by ESD is present whenever components are transported,
stored, or used. The risk of ESD damage can be greatly reduced by paying close attention to how all
components are handled.
— Perform work on all components at a static-safe workstation.
— Keep static-generating materials at least one meter away from all components.
— Store or transport components in static-shielding containers.
Test Equipment Usage and ESD
— Before connecting any coaxial cable to an analyzer connector, momentarily short the center and
outer conductors of the cable together.
— Personnel should be grounded with a 1 megohm resistor-isolated wrist-strap before touching
the center pin of any connector and before removing any assembly from the analyzer.
— Be sure that all analyzers are properly earth-grounded to prevent build-up of static charge.
For Additional Information about ESD
For more information about preventing ESD damage, contact the Electrical Over
Stress/Electrostatic Discharge (EOS/ESD) Association, Inc. The ESD standards developed by this
agency are sanctioned by the American National Standards Institute (ANSI).
Always handle printed circuit board assemblies by the edges. This will reduce the possibility of
ESD damage to components and prevent contamination of exposed plating.

Installation Note N9032-90010 7
Option ST1 and ST2 – IQ Streaming
Upgrade Contents
Table 1 Upgrade Contents
Part Number Description Quantity
0515-0372 Screw-Machine w/Crest-Cup-Con-Washer Pan-HD Torx-T10 M3X0.5 8mm-LG 2
0515-0666 Screw-Machine w/Crest-Cup-Washer Pan-HD Torx-T10 M3X0.5 18mm-LG 1
0515-1946 Screw-Machine w/Patch Lock 90-DEG-flat-HD Torx-T10 M3X0.5 6mm-LG 18
0515-2332 Screw-Machine w/Patch-Lock Pan-HD Torx-T10 M3X0.5 6mm-LG 4
0515-5208 Screw-Machine w/Patch-Lock Flat-HD Torx-T6 M2X0.4 4mm-LG 1
1005-1388 Fiber Optic Adapter MPO-Shutter Female-Female flange-mount 1
1400-0082 Screw Mount Cable Clamp 4
1400-0249 Nylon Cable Tie 2
1400-1254 Adhesive Cable Clip 2
9030-0000 License Entitlement Certificate 1
M8121-60004 Connector-Fiber Optic Multimode MPO-Loopback 1
M8121-61614 Cable AY, Patch cord, ODI, F-F, 24 fiber, Type C, 3 M lg 1
M9484-80048 Label, FDA Laser 1
N9032-61000 Cable Assembly, Optical FireFly TX/RX 1
N9041-20154 Heatsink, FireFly 1
N9041-20181 Insertion Tool, FireFly 1

8Installation Note N9032-90010
Option ST1 and ST2 – IQ Streaming
Tools Required
—Torx Driver T-10
—Torx Driver T-20
—Multi-Bit Torque Driver
—5/8” Nut Driver
—5/16” Wrench
Initial Instrument Functionality Check
Power on the instrument and allow it to complete its boot up process. Verify that there are no
instrument messages that would indicate that there is an issue with either the instrument hardware
or software. If there are any issues, investigate and fix the problem before continuing with this
upgrade.
Instrument Software Revision Check
While the instrument is still powered on check to see what version of the instrument software is
installed. To do so press System, Show System and look on the System Information screen for the
Instrument S/W Revision. Record the software revision below.
Instrument S/W Revision Installed: __________

Installation Note N9032-90010 9
Option ST1 and ST2 – IQ Streaming
Upgrade Instructions
Hardware Disassembly
Dress Cover Removal
1. Turn the instrument off and disconnect the power cord.
2. Referring to Figure 2, remove the two screws (1) that attach the strap handle (2) from both
sides and remove the strap handles.
Figure 2 Dress Cover Removal
3. Remove the four rear feet (4) by removing the four screws (3) and washers that attach them.
4. Remove the four bottom feet (6) by first removing the locking keys and then lifting the tabs
and sliding the foot toward the tabs.
5. Carefully slide the dress cover (5) off the instrument.

10 Installation Note N9032-90010
Option ST1 and ST2 – IQ Streaming
Top Brace Removal
6. Referring to Figure 3, remove the sixteen flathead screws (2) and twelve panhead screws (3)
attaching the top brace (1) to the instrument and set it aside. The sixteen flathead screws can
be discarded, and they will be replaced with new ones.
Figure 3 Remove Top Brace
Blank Plate Removal
7. Referring to Figure 4, remove the two panhead screws (1) securing the blank plate (2) to the
rear panel and discard the plate.
Figure 4 Remove Blank Plate