Khyam Kamper Cozi User manual

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 1.
Remove the cover from its carry bag and lay
out on the ground next to the passenger side of
your vehicle, ensuring that the soft lining is
facing upwards and that the front of your cover
(with the third window) is facing forward. To
prevent the cover getting dusty or dirty we
recommend placing a groundsheet on the
floor first.
Step 2.
Take hold of the white beading at the front
corner of your cover, which should be nearest
to your vehicle, and begin to feed the beading
in to the aluminium awning rail which runs along
the passenger side of your vehicle. Start at the
rear and feed it along until the cover is
attached from front to back. The cover should
hang down with the soft lining facing out.
Step 3.
Open the front passenger door and stand on
the step, then gather as much of the cover as
possible and sweep it across the roof of your
vehicle. Go around to the driver’s side and pull
the cover across so that it doesn’t fall off.
In windy conditions you may need assistance of
a second person, or park so that the wind is
blowing across the roof from the passenger
side.
Step 4.
Raise the roof 12” or so at the front so that there
is a small opening at the rear. Pull the cover
gently down so that the front two corners of the
roof are inside the front two corners of the
cover.
It is important to get this right to ensure correct
fit of your cover. Once the front two corners are
in place, pull the rear corners of the cover over
the rear corners of your roof.
Step 5.
Once all four corners are correctly in place,
continue raising the roof as per your
manufacturer instructions. When the roof is fully
raised, the cover will fit nicely along the
passenger side and the driver’s side should be
hanging down with the 5 buckle fasteners.
Step 6. (no fixed awning)
If your vehicle is not fitted with a fixed roll out
awning, simply undo the 5 clips, slide them
along the awning rail, clip them all into place
and gently tighten the adjustable straps so that
the cover first neatly all the way along. Do not
over tighten as you do not want to exert
excessive pressure on the roof.

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 1.
Remove the cover from its carry bag and lay
out on the ground next to the passenger side of
your vehicle, ensuring that the soft lining is
facing upwards and that the front of your cover
(with the third window) is facing forward. To
prevent the cover getting dusty or dirty we
recommend placing a groundsheet on the
floor first.
Step 2.
Take hold of the white beading at the front
corner of your cover, which should be nearest
to your vehicle, and begin to feed the beading
in to the aluminium awning rail which runs along
the passenger side of your vehicle. Start at the
rear and feed it along until the cover is
attached from front to back. The cover should
hang down with the soft lining facing out.
Step 3.
Open the front passenger door and stand on
the step, then gather as much of the cover as
possible and sweep it across the roof of your
vehicle. Go around to the driver’s side and pull
the cover across so that it doesn’t fall off.
In windy conditions you may need assistance of
a second person, or park so that the wind is
blowing across the roof from the passenger
side.
Step 4.
Raise the roof 12” or so at the front so that there
is a small opening at the rear. Pull the cover
gently down so that the front two corners of the
roof are inside the front two corners of the
cover.
It is important to get this right to ensure correct
fit of your cover. Once the front two corners are
in place, pull the rear corners of the cover over
the rear corners of your roof.
Step 5.
Once all four corners are correctly in place,
continue raising the roof as per your
manufacturer instructions. When the roof is fully
raised, the cover will fit nicely along the
passenger side and the driver’s side should be
hanging down with the 5 buckle fasteners.
Step 6. (no fixed awning)
If your vehicle is not fitted with a fixed roll out
awning, simply undo the 5 clips, slide them
along the awning rail, clip them all into place
and gently tighten the adjustable straps so that
the cover first neatly all the way along. Do not
over tighten as you do not want to exert
excessive pressure on the roof.

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 1.
Remove the cover from its carry bag and lay
out on the ground next to the passenger side of
your vehicle, ensuring that the soft lining is
facing upwards and that the front of your cover
(with the third window) is facing forward. To
prevent the cover getting dusty or dirty we
recommend placing a groundsheet on the
floor first.
Step 2.
Take hold of the white beading at the front
corner of your cover, which should be nearest
to your vehicle, and begin to feed the beading
in to the aluminium awning rail which runs along
the passenger side of your vehicle. Start at the
rear and feed it along until the cover is
attached from front to back. The cover should
hang down with the soft lining facing out.
Step 3.
Open the front passenger door and stand on
the step, then gather as much of the cover as
possible and sweep it across the roof of your
vehicle. Go around to the driver’s side and pull
the cover across so that it doesn’t fall off.
In windy conditions you may need assistance of
a second person, or park so that the wind is
blowing across the roof from the passenger
side.
Step 4.
Raise the roof 12” or so at the front so that there
is a small opening at the rear. Pull the cover
gently down so that the front two corners of the
roof are inside the front two corners of the
cover.
It is important to get this right to ensure correct
fit of your cover. Once the front two corners are
in place, pull the rear corners of the cover over
the rear corners of your roof.
Step 5.
Once all four corners are correctly in place,
continue raising the roof as per your
manufacturer instructions. When the roof is fully
raised, the cover will fit nicely along the
passenger side and the driver’s side should be
hanging down with the 5 buckle fasteners.
Step 6. (no fixed awning)
If your vehicle is not fitted with a fixed roll out
awning, simply undo the 5 clips, slide them
along the awning rail, clip them all into place
and gently tighten the adjustable straps so that
the cover first neatly all the way along. Do not
over tighten as you do not want to exert
excessive pressure on the roof.

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 1.
Remove the cover from its carry bag and lay
out on the ground next to the passenger side of
your vehicle, ensuring that the soft lining is
facing upwards and that the front of your cover
(with the third window) is facing forward. To
prevent the cover getting dusty or dirty we
recommend placing a groundsheet on the
floor first.
Step 2.
Take hold of the white beading at the front
corner of your cover, which should be nearest
to your vehicle, and begin to feed the beading
in to the aluminium awning rail which runs along
the passenger side of your vehicle. Start at the
rear and feed it along until the cover is
attached from front to back. The cover should
hang down with the soft lining facing out.
Step 3.
Open the front passenger door and stand on
the step, then gather as much of the cover as
possible and sweep it across the roof of your
vehicle. Go around to the driver’s side and pull
the cover across so that it doesn’t fall off.
In windy conditions you may need assistance of
a second person, or park so that the wind is
blowing across the roof from the passenger
side.
Step 4.
Raise the roof 12” or so at the front so that there
is a small opening at the rear. Pull the cover
gently down so that the front two corners of the
roof are inside the front two corners of the
cover.
It is important to get this right to ensure correct
fit of your cover. Once the front two corners are
in place, pull the rear corners of the cover over
the rear corners of your roof.
Step 5.
Once all four corners are correctly in place,
continue raising the roof as per your
manufacturer instructions. When the roof is fully
raised, the cover will fit nicely along the
passenger side and the driver’s side should be
hanging down with the 5 buckle fasteners.
Step 6. (no fixed awning)
If your vehicle is not fitted with a fixed roll out
awning, simply undo the 5 clips, slide them
along the awning rail, clip them all into place
and gently tighten the adjustable straps so that
the cover first neatly all the way along. Do not
over tighten as you do not want to exert
excessive pressure on the roof.

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 1.
Remove the cover from its carry bag and lay
out on the ground next to the passenger side of
your vehicle, ensuring that the soft lining is
facing upwards and that the front of your cover
(with the third window) is facing forward. To
prevent the cover getting dusty or dirty we
recommend placing a groundsheet on the
floor first.
Step 2.
Take hold of the white beading at the front
corner of your cover, which should be nearest
to your vehicle, and begin to feed the beading
in to the aluminium awning rail which runs along
the passenger side of your vehicle. Start at the
rear and feed it along until the cover is
attached from front to back. The cover should
hang down with the soft lining facing out.
Step 3.
Open the front passenger door and stand on
the step, then gather as much of the cover as
possible and sweep it across the roof of your
vehicle. Go around to the driver’s side and pull
the cover across so that it doesn’t fall off.
In windy conditions you may need assistance of
a second person, or park so that the wind is
blowing across the roof from the passenger
side.
Step 4.
Raise the roof 12” or so at the front so that there
is a small opening at the rear. Pull the cover
gently down so that the front two corners of the
roof are inside the front two corners of the
cover.
It is important to get this right to ensure correct
fit of your cover. Once the front two corners are
in place, pull the rear corners of the cover over
the rear corners of your roof.
Step 5.
Once all four corners are correctly in place,
continue raising the roof as per your
manufacturer instructions. When the roof is fully
raised, the cover will fit nicely along the
passenger side and the driver’s side should be
hanging down with the 5 buckle fasteners.
Step 6. (no fixed awning)
If your vehicle is not fitted with a fixed roll out
awning, simply undo the 5 clips, slide them
along the awning rail, clip them all into place
and gently tighten the adjustable straps so that
the cover first neatly all the way along. Do not
over tighten as you do not want to exert
excessive pressure on the roof.

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 1.
Remove the cover from its carry bag and lay
out on the ground next to the passenger side of
your vehicle, ensuring that the soft lining is
facing upwards and that the front of your cover
(with the third window) is facing forward. To
prevent the cover getting dusty or dirty we
recommend placing a groundsheet on the
floor first.
Step 2.
Take hold of the white beading at the front
corner of your cover, which should be nearest
to your vehicle, and begin to feed the beading
in to the aluminium awning rail which runs along
the passenger side of your vehicle. Start at the
rear and feed it along until the cover is
attached from front to back. The cover should
hang down with the soft lining facing out.
Step 3.
Open the front passenger door and stand on
the step, then gather as much of the cover as
possible and sweep it across the roof of your
vehicle. Go around to the driver’s side and pull
the cover across so that it doesn’t fall off.
In windy conditions you may need assistance of
a second person, or park so that the wind is
blowing across the roof from the passenger
side.
Step 4.
Raise the roof 12” or so at the front so that there
is a small opening at the rear. Pull the cover
gently down so that the front two corners of the
roof are inside the front two corners of the
cover.
It is important to get this right to ensure correct
fit of your cover. Once the front two corners are
in place, pull the rear corners of the cover over
the rear corners of your roof.
Step 5.
Once all four corners are correctly in place,
continue raising the roof as per your
manufacturer instructions. When the roof is fully
raised, the cover will fit nicely along the
passenger side and the driver’s side should be
hanging down with the 5 buckle fasteners.
Step 6. (no fixed awning)
If your vehicle is not fitted with a fixed roll out
awning, simply undo the 5 clips, slide them
along the awning rail, clip them all into place
and gently tighten the adjustable straps so that
the cover first neatly all the way along. Do not
over tighten as you do not want to exert
excessive pressure on the roof.

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 6. (with fixed awning)
If your vehicle is fitted with a fixed roll out awning, undo the two
clips at the front and one at the rear, slide the front two into the
aluminium awning rail from the front, attach them to the clips
on the cover and tighten (do not over tighten straps). Slide the
rear clip into the aluminium awning rail at the back and attach
it to the rear strap before tightening (do not over tighten). Each
of the clips have a metal hook which has been designed to clip
into the rear backing plate of the ‘fixed awning’. So, the
remaining two straps can be secured to the backing plate of
the fixed awning if so desired.
Alternatively, you can use the Velcro tabs which have been
attached to the rear of each strap and a corresponding piece
with a sticky back Velcro also enclosed. These can be used to
stick the Velcro to the side of your vehicle behind the fixed
awning and the two centre straps can then be attached to
them to prevent flapping.
Step 7.
Two further straps are fitted to the rear of your vehicle roof
cover. If necessary, these can be used to further fix your cover
to your vehicle. These straps may either be passed around the
inside of the rear door hinge of your vehicle, or alternatively, if
your vehicle is fitted with a rear door mounted bicycle carrier,
they can be fixed to a suitable area of that.
Your vehicle roof cover will fit securely to your vehicle providing
increased insulation and protection to the roof bellows. To
remove the cover simply follow the instructions in reverse,
remembering to undo all clips prior to lowering the roof, then
remove the rear corners first for ease of removal.

Khyam
Khyam Kamper Cozi Instructions for the VW California
Step 6. (with fixed awning)
If your vehicle is fitted with a fixed roll out awning, undo the two
clips at the front and one at the rear, slide the front two into the
aluminium awning rail from the front, attach them to the clips
on the cover and tighten (do not over tighten straps). Slide the
rear clip into the aluminium awning rail at the back and attach
it to the rear strap before tightening (do not over tighten). Each
of the clips have a metal hook which has been designed to clip
into the rear backing plate of the ‘fixed awning’. So, the
remaining two straps can be secured to the backing plate of
the fixed awning if so desired.
Alternatively, you can use the Velcro tabs which have been
attached to the rear of each strap and a corresponding piece
with a sticky back Velcro also enclosed. These can be used to
stick the Velcro to the side of your vehicle behind the fixed
awning and the two centre straps can then be attached to
them to prevent flapping.
Step 7.
Two further straps are fitted to the rear of your vehicle roof
cover. If necessary, these can be used to further fix your cover
to your vehicle. These straps may either be passed around the
inside of the rear door hinge of your vehicle, or alternatively, if
your vehicle is fitted with a rear door mounted bicycle carrier,
they can be fixed to a suitable area of that.
Your vehicle roof cover will fit securely to your vehicle providing
increased insulation and protection to the roof bellows. To
remove the cover simply follow the instructions in reverse,
remembering to undo all clips prior to lowering the roof, then
remove the rear corners first for ease of removal.