Kicker Kx400.1 User manual

KX MONO AMPLIFIERS

KX400.1 | KX800.1 | KX1200.1 | KX1600.1 | KX2400.1

Owner’s Manual | English

Manual del Propietario | Español

AMPLIFICADOR DEL LA SERIE KX.1

Benutzerhandbuch | Deutsch

MONOVERSTÄRKER DER KX.1-SERIE

Manuel d’utilisation | Française

AMPLIFICATEUR DE SÉRIE KX.1

KX Amplifiers

2013 KX Mono Amps Rev G.indd 12013 KX Mono Amps Rev G.indd 1 11/13/2012 2:13:57 PM11/13/2012 2:13:57 PM

KX.1-SERIES AMPLIFIERS

OWNER’S MANUAL

INSTALLATION

Mounting: Choose a structurally sound location to mount your KICKER ampliﬁer. Make sure there are no items

behind the area where the screws will be driven. Choose a location that allows at least 4” (10cm) of open

ventilation for the ampliﬁer. If possible, mount the ampliﬁer in the climate-controlled passenger compartment. Drill

four holes using a 7/64” (3mm) bit and use the supplied #8 screws to mount the ampliﬁer.

PERFORMANCE

Authorized KICKER Dealer:

Purchase Date:

Model Number:

Serial Number:

Model: KX400.1 KX800.1 KX1200.1 KX1600.1 KX2400.1

RMS Power

@ 14.4V, 4Ωmono, 1% THD+N

@ 14.4V, 2Ωmono, 1% THD+N

200W x 1

400W x 1

800W x 1

600W x 1

1200W x 1

800W x 1

1600W x 1

1200W x 1

2400W x 1

Length | in [cm] 8 [20.4] 9 9/16 [24.4] 9 9/16 [24.4] 11 3/16 [28.4] 15 1/2 [39.4]

Speciﬁcations common to all models:

Height | in [cm] 2 1/8 [5.5]

Width | in [cm] 8 5/16 [21]

Frequency Response ± 1dB 10Hz–160Hz

Signal-to-noise Ratio >95dB, A-weighted, re: rated power

Input Sensitivity Low Level: 125mV–5V

High Level: 250mV–10V

Electronic Crossover Variable Lo-pass 40Hz–160Hz, 24dB/octave

Bass Boost Parametric 20-80Hz; Variable Q: 1 to 5; Variable Boost, 0-18dB

Subsonic Filter Variable 10–80Hz, 24dB/octave

Remote Bass Yes [included]

Pro Tip: To get the best performance from your new KICKER Ampliﬁer and extend the warranty by 1 year, use

genuine KICKER accessories and wiring.

MODEL: KX400.1 / KX800.1 / KX1200.1 / KX1600.1 / KX2400.1

2013 KX Mono Amps Rev G.indd 22013 KX Mono Amps Rev G.indd 2 11/13/2012 2:17:11 PM11/13/2012 2:17:11 PM

Wiring: Disconnect the vehicle’s battery to avoid an electrical short. Then, connect the ground wire to the

ampliﬁer. Make the ground wire short, 24” (60cm) or less, and connect it to a paint-and-corrosion-free, solid,

metal area of the vehicle’s chassis. Adding an additional ground wire of this same gauge (or larger) between the

battery’s negative post and the vehicle chassis is recommended.

The KX ampliﬁer has dual input sensitivity differential RCA inputs which will receive either high or low level signals

from your car stereo’s source unit. A high-level signal can be run from the source unit’s speaker outputs to the

stereo RCA input on the end panel of the ampliﬁer using the KICKER ZISL as shown (make sure you set the KX

ampliﬁer’s input level switch to “HI”). Alternatively, the signal can be delivered to the ampliﬁer using the low-level

RCA outputs on the source unit. Set the input level switch on the end panel of the ampliﬁer to “LO”. Either input

method will provide a low-level output signal at the RCA output, which effectively passes the audio signal to

another ampliﬁer or component. Keep the audio signal cable away from factory wiring harnesses and other

power wiring. If you need to cross this wiring, cross it at a 90 degree angle.

source unit

high-level speaker

outputs

to ampliﬁer

shield

––

–

core conductor KICKER ZISL (optional)

source unit high-level

speaker outputs

OR to ampliﬁer

Model External Fuse

(sold separately)

Power/Ground Wire KICKER Wiring Kit

KX400.1 1 x 60 Ampere 4 Gauge PK4, CK44, ZCK44

KX800.1 1 x 100 Ampere 4 Gauge PK4, CK44, ZCK44

KX1200.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050

KX1600.1 1 x 150 Ampere 1/0 Gauge PKD1, PWB050

KX2400.1 1 x 200 Ampere 1/0 Gauge PKD1, PWB050

Install a fuse within 18” (45cm) of the battery and in-line with the power cable connected to your ampliﬁer. If you

ever need to remove the ampliﬁer from the vehicle after it has been installed, the ground wire should be the last

wire disconnected from the ampliﬁer--just the opposite as when you installed it.

2013 KX Mono Amps Rev G.indd 32013 KX Mono Amps Rev G.indd 3 11/13/2012 2:17:12 PM11/13/2012 2:17:12 PM

12V

battery

external fuse

remote turn-on

(see page 5)

bare-metal

chassis ground

bare-metal

chassis ground

18”

(45cm)

24”

(60cm)

woofer

MONO OPERATION

minimum impedance of 2 ohms

2013 KX Mono Amps Rev G.indd 42013 KX Mono Amps Rev G.indd 4 11/13/2012 2:17:12 PM11/13/2012 2:17:12 PM

OPERATION

Automatic Turn-On Selection: The KX series offers three different automatic turn-on modes that can be

selected on the end panel; +12V, DC Offset, and Audio. Using either the DC Offset or Audio mode causes the

REM terminal to have +12V out for turning on additional ampliﬁers.

• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from your source unit. Run 18

gauge wire from the Remote Turn-On Lead on your source unit to the terminal labeled REM between the

ampliﬁer’s positive and negative power terminals. This is the preferred automatic turn-on method.

• DC Offset Turn-On: If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset

mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned on.

• Signal Sense Turn-On: The Audio setting is the ﬁnal alternative for Automatic turn-on. This is a Signal Sense

turn-on method that detects the incoming audio signal from your source unit and automatically turns on the

amp. This turn-on method will not work properly if the input gain control is not set appropriately.

Input Level: The RCA inputs on KICKER KX ampliﬁers are capable of receiving either Hi or Low-level signals

from your source unit. If the only output available from your source unit is a Hi-Level signal, simply press in the

Input Level switch on the ampliﬁer. Refer to the wiring section of this manual for additional instructions.

Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to

the input level of the ampliﬁer. Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it

to 25). Next, slowly turn (clockwise) the gain on the ampliﬁer up until you can hear audible distortion, then turn it

down a little.

Adjustable Subsonic Filter: The variable subsonic ﬁlter will provide a cut-off point for lower frequencies

(10–80Hz) that could potentially damage your speakers from over-excursion, along with wasting your ampliﬁer’s

power. The setting for this control should be set relative to your speaker’s low-frequency capability.

Crossover Control: The variable crossover on the ampliﬁer is always active, and allows you to adjust the LO-

PASS crossover frequency from 40–160Hz. The setting for this control is subjective; 80Hz is a good place to

start.

KICK EQ+ Bass Boost Control: The variable bass boost control on the side of the ampliﬁer is designed to

give you increased output, 0–18dB, at the selected frequency. A higher BANDWIDTH (Q) setting will result in

a sharper cut at the frequencies above and below the selected center frequency. The setting for this control is

subjective. If you turn it up, you must readjust the input gain control to avoid clipping the ampliﬁer.

Remote Bass-KXRC: With the optional KXRC remote bass level control, you have the ability to control the

output level of the ampliﬁer remotely. To surface-mount the KXRC remote bass level control, simply screw the

remote to the chosen location, then run the cable from the controller to the “Remote Bass” jack on the ampliﬁer

panel. Do NOT connect/disconnect while the ampliﬁer is on. See page 6 for installation.

Mini-USB for internal use only; do NOT remove or tamper. KICKER is not responsible for any

damage to equipment resulting from connections made to this port.

2013 KX Mono Amps Rev G.indd 52013 KX Mono Amps Rev G.indd 5 11/13/2012 2:17:13 PM11/13/2012 2:17:13 PM

KXRC REMOTE BASS INSTALLATION

Surface-mount the KXRC remote

using the supplied screws.

Connect the supplied cable to the KXRC remote and the

Remote Bass jack on the ampliﬁer

back view

TROUBLESHOOTING

If your ampliﬁer does not appear to be working, check the obvious things ﬁrst such as blown fuses, poor or

incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There is a Protection

(PRT) LED on the side panel of your Kicker KX series ampliﬁer. Depending on the state of the ampliﬁer and the

vehicle’s charging system, the LED will either glow red or be off.

Red (PRT) LED ﬂickering with loud music? The red (PRT) LED indicates low battery voltage. Check all the

connections in your vehicle’s charging system. It may be necessary to replace or charge your vehicle’s battery or

replace your vehicle’s alternator.

Red (PRT) LED on, no output? Ampliﬁer is very hot = thermal protection is engaged. Test for proper

impedance at the speaker terminals with a VOM meter (see the diagrams in this manual for minimum

recommended impedance and multiple speaker wiring suggestions). Also check for adequate airﬂow around

the ampliﬁer. Ampliﬁer shuts down only while vehicle is running = voltage protection circuitry is engaged.

Voltage to the ampliﬁer is not within the 10–16 volt operating range. Have the vehicle’s charging and electrical

system inspected. Ampliﬁer will only play at low volume levels = short circuit protection is engaged. Check

for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)

operating below the minimum recommended impedance.

No or low output? Check the balance control on source unit Check the RCA (or speaker input) and

speaker output connections.

Alternator noise-whining sound with engine’s RPM? Check for damaged RCA (or speaker input) cable

Check the routing of RCA (or speaker input) cable Check the source unit for proper grounding Check

the gain settings and turn them down if they are set too high.

Ground Noise? KICKER ampliﬁers are engineered to be fully compatible with all manufacturers’ head units.

Some head units may require additional grounding to prevent noise from entering the audio signal. If you are

experiencing this problem with your head unit, in most cases running a ground wire from the RCA outputs on the

head unit to the chassis will remedy this issue.

CAUTION: When jump starting the vehicle, be sure that connections made with jumper cables are correct.

Improper connections can result in blown ampliﬁer fuses as well as the failure of other critical systems in the

vehicle.

2013 KX Mono Amps Rev G.indd 62013 KX Mono Amps Rev G.indd 6 11/13/2012 2:17:14 PM11/13/2012 2:17:14 PM

KICKER will now provide a three-

year warranty with all KX-Series

Ampliﬁer purchases paired with a

qualifying KICKER Installation Kit* .

This extends the standard warranty by an additional

year. Ampliﬁer and Kit must be purchased from an

Authorized KICKER Dealer.

KICKER KX ampliﬁer success is currently at an unheard-of rate, making the extended

warranty program even more beneﬁcial to you.

Using poor-quality, under-spec wiring kits will impede KX ampliﬁer performance.

A superior-quality KICKER installation Kit is guaranteed to extend the life of KX

ampliﬁers.

The new extended warranty applies only to KICKER ampliﬁers and accessories sold to consumers by Authorized

KICKER Dealers in the United States of America or its possessions. It also only applies to the original purchaser of

KICKER ampliﬁers and accessories. One warranty extension per ampliﬁer is allowed regardless of the number of ampliﬁer

installation kits purchased. This program does not apply to “B”-stock product or factory-refurbished product.

This offer is for a limited time, so see your local Authorized KICKER Dealer soon for details.

*U.S.A. Only | EE.UU. solamente | Nur USA | Les USA Seulement

KX400.1

200 x 1 @ 4 ohms, 14.4VDC, 1% THD, CEA-2006B (Watts)