Kicker PX100.2 User manual

lfKICKER
MODEL:
Authorized KICKER Dealer:
Purchase Date:
Serial Number:
PERFORMANCE
Model:
RMS Power
@ 2n stereo,~ 1% THD+N
@ 4Q stereo, ~ 1% THD+N
Length,
in. [em]
Height, in. [mm]
Width,
in. [mm]
Frequency Response ± 1
dB
Signal-to-noise Ratio
Input Sensitivity
Electronic Crossover
PX.2-SERIES AMPLIFIERS
OWNER'S MANUAL
PX100.2
PX100.2
50Wx2
25Wx2
6-5/16" [17.6]
2" [50.6]
3-1 /2" [88.2]
20Hz-20KHz
>85d8, A-weighted, re: rated power
Low Level: 1
25mV-5V
High Level: 250mV-1 OV
Selectable 1OOHz, 250Hz or OFF; 24dB/octave
Pro Tip: To get the best performance from your new KICKER Amplifier and extend the warranty by 1 year, use
genuine
KICKER accessories and wiring.
INSTALLATION
Mounting: Choose a structurally sound location to mount your KICKER amplifier. Make sure there are no items
behind the area where the screws
will be driven. Choose a location that allows at least 4" (1 Ocm) of open
ventilation for the amplifier.
Drill four holes using a 7/64" (3mm) bit and use the supplied #8 screws to mount the
amplifier.
Wiring: Disconnect the vehicle's battery to avoid an electrical short. Then, connect the PX harness to the
amplifier. Connect the ground wire to a paint-and-corrosion-free, solid, metal area of the vehicle's chassis,
making
it no longer than 24" (60cm). Adding an additional ground wire of this same gauge (or larger) between the
battery's negative post and the vehicle chassis
is recommended.
2

The
PX
amplifier has dual input sensitivity differential inputs which will receive either high or
low
level signals
from your stereo's source unit. A high-level signa. can
be
run from the source
un1t's
speaker outputs
to
the
stereo RCA input
on
the end panel
of
the amplifier using the KICKER ZISL as shown (make sure you
set
the PX
ampl fier's input level switch to
"HI").
Alternatively, the
s1gnal
can
be
delivered to the amplifier using the low-level
RCA outputs
on
the source
un1t.
Set the
1nput
level switch on the end panel
of
the amplifier
to
"LO". Either
input method
wll
provide a hi-level signal at the output Keep the audio signal cable away from factory wiring
harnesses and other
power
w1ring.
If
you need
to
cross
th1s
w1nng,
cross
1t
at a
go
degree angle
source unit
high-level speaker core conductor
o
~
tputs
····p
-
~
shield
to amplifier
OR
~
source
unit high-level
speaker outputs
Cut
the looped red
power
cable 1ocated on the PX harness and
1nstall
a
1
OA
fuse. Fuse
Jnstallat1on
should
be
within 18" (45cm)
of
the battery and
1n
line
w1th
the harness' power cable,
wh1ch
is connected to your amplifier. If
you ever need to remove the amplifier from the veh1cle after it
has
been installed, the ground wire should
be
the
last wire disconnected from the amplifier ·
JUSt
the oppos1te as when you installed it.
IIIII
-
--
~
24
"
(60cm)
bare-metal
chassis ground
RCA Inputs
(remove
to
use
hi-level1nput R+
R-
Model
PX100.2
L+
speaker outputs
External
Fuse
(sold separately)
1
x
10
Ampere
~
18
"
(45cm)
remote
turn-or
(see page 5)
L-
•I
battery -
---
bare-metal
chass1s ground
3

OPERATION
INPUT LEVEL
AUTO TURN ON
GAIN
100Hz
OFFL012V
~~~
ON HI DC
250Hz
PWR
IPRT
Automatic Turn-On Selection: The PX series offers two automatic turn-on modes that can be selected on the
end panel; +12V or DC Offset. Using the DC Offset mode causes the
REM terminal wire to have +12V out for
turning on additional amplifiers.
• Remote Turn-On: Set the switch to +12V to use the remote turn-on lead from the
PX harness. Run 18
gauge wire from the Remote Turn-On Lead
on your source unit to the REM wire on the PX harness. This is
the preferred automatic turn-on method.
• DC Offset Turn-On:
If Remote Turn-On is not an option, the next best setting is DC Offset. The DC Offset
mode detects a 6V DC offset from the HI-Level speaker outputs when the source unit has been turned
on.
Input Level: The RCA inputs on KICKER PX amplifiers are capable of receiving either Hi or Low-level signals
from your source unit.
If the only output available from your source unit is a Hi-Level signal, simply set the Input
Level switch
on the amplifier to HI.
Crossover Switches: Use the HI-PASS switch on the end panel of the amplifier to set the internal crossover to
OFF or ON. When the switch
is set to OFF, a full bandwidth signal will be amplified. Set the switch to ON if you
want the amplifier's internal crossover to serve as a high-pass
filter. Choose a cutoff of 1OOHz or 250Hz with the
crossover selection switch. Never change the crossover "OFF/ON" switch with the audio system
on!
Input Gain Control: The input gain control is not a volume control. It matches the output of the source unit to
the input level of the amplifier.
Turn the source unit up to about 3/4 volume (if the source unit goes to 30, turn it
to 25). Next, slowly turn (clockwise) the gain on the amplifier up until you can hear audible distortion, then turn it
down a little.
4

TROUBLESHOOTING
If
your amplifier does not appear to be working, check the obvious things first such as blown fuses, poor or
incorrect wiring connections, incorrect setting of crossover switch and gain controls, etc. There
is
a Power
Protection
LED
on the side power panel of your Kicker
PX
series amplifier. Depending
on
the state of the amplifier
and the vehicle's charging system, the
LED
will
glow either
Red
or Blue. When the blue
LED
is
lit
this indicates
the amplifier
is
turned on and no trouble exists.
Blue LED off,
no
output?
With a Volt Ohm Meter
(VOM)
check the following:
0+
12 volt power terminal
(should read +12V
to+
16V)
f)
Remote turn-on terminal (should read +12V
to+
16V)
C)
Check for reversed
power and ground connections 0 Ground terminal, for proper conductivity.
Blue LED on,
no
output?
Check the following:
ORCA
connections @Test speaker outputs with a "known"
good speaker.
C)
Substitute source unit with a "known" good source unit.
0Check
for a signal
in
the RCA
cable feeding the amplifier with the VOM meter set to measure "AC" voltage.
Protection LED flashing with loud music?
The red
LED
indicates low battery voltage. Check
all
the
connections
in
your vehicle's charging system.
It
may be necessary to replace or charge your vehicle's battery or
replace your vehicle's alternator.
Protection LED on,
no
output?
0Amplifier
is
very
hot=
thermal protection
is
engaged. Test for proper
impedance at the speaker terminals with a VOM meter (see the diagrams
in
this manual for minimum
recommended impedance and multiple speaker wiring suggestions). Also check for adequate airflow around
the amplifier. @Amplifier shuts down only while vehicle
is
running = voltage protection circuitry
is
engaged.
Voltage to the amplifier
is
not within the
10-16
volt operating range. Have the vehicle's charging and electrical
system inspected.
C)
Amplifier
will
only play
at
low volume levels= short circuit protection
is
engaged. Check
for speaker wires shorted to each other or to the vehicle chassis. Check for damaged speakers or speaker(s)
operating below the minimum recommended impedance.
No or low output?
0Check
the balance control on source unit
@Check
the RCA
(or
speaker input) and
speaker output connections.
Alternator noise-whining sound with engine's RPM?
0Check
for damaged RCA
(or
speaker input) cable
f)
Check the routing of RCA
(or
speaker input) cable
C)
Check the source unit for proper grounding
0Check
the gain settings and turn them down
if
they
are
set too high.
Reduced bass response?
Reverse a speaker connection from positive to negative on the stereo/subwoofer
channel(s);
if
the bass improves, the speaker was out of phase.
Ground Noise?
KICKER amplifiers are engineered to be fully compatible with
all
manufacturers' head units.
Some head units may require additional grounding to prevent noise from entering the audio signal.
If
you
are
experiencing this problem with your head unit,
in
most cases running a ground wire from the RCA outputs on the
head unit to the chassis
will
remedy this issue.
CAUTION:
When jump starting the vehicle, be sure that connections made with jumper cables are correct.
Improper connections can result
in
blown amplifier fuses
as
well as the failure of other critical systems
in
the
vehicle.
If
you have more questions about the installation or operation
of your new
KICKER
product, see the Authorized KICKER
Dealer where you made your purchase. For more advice
on installation, click on the SUPPORT tab on the KICKER
homepage,
www.kicker.com.
Choose the TECHNICAL
SUPPORT tab, choose the subject you are interested
in,
and
then download or view the corresponding information. Please
E-mail [email protected] or call Technical Services (405)
624-8583
for unanswered or specific questions.
5

ELECTRONICS LIMITED WARRANTY
When purchased from an Authorized KICKER Dealer, KICKER warrants this product to be free from defects in material
and workmanship under normal use for a period of TWO
(2) YEARS from date of original purchase. If this product is
identified as "Refurbished" or "B Goods", the warranty is limited to a period of THREE (3) MONTHS from date of original
purchase.
In all cases you must have the original receipt. Should service be necessary under this warranty for any reason
due to manufacturing defect or malfunction during the warranty period,
KICKER will repair or replace (at its discretion)
the defective merchandise with equivalent merchandise. Warranty replacements may have cosmetic scratches and
blemishes. Discontinued products may be replaced with more current equivalent products. This warranty
is valid only for
the original purchaser and
is not extended to owners of the product subsequent to the original purchaser. Any applicable
implied warranties are limited
in duration to a period of the express warranty as provided herein beginning with the date of
the original purchase at retail, and no warranties, whether express or implied, shall apply to this product thereafter. Some
states do not allow limitations
on implied warranties; therefore, these exclusions may not apply to you. This warranty
gives you specific legal rights; however you may have other rights that vary from state to state.
WHAT TO DO IF YOU NEED WARRANTY OR SERVICE:
Defective merchandise should be returned to your local Authorized Stillwater Designs (KICKER) Dealer for warranty
service. Assistance
in locating an Authorized Dealer can be found at www.kicker.com or by contacting Stillwater Designs
directly.
You can confirm that a dealer is authorized by asking to see a current authorized dealer window decal.
If it becomes necessary for you to return defective merchandise directly to Stillwater Designs (KICKER), call the KICKER
Customer Service Department at (405) 624-851 0 for a Return Merchandise Authorization (RMA) number. Package only
the defective items
in a package that will prevent shipping damage, and return to:
Stillwater Designs, 3100 North Husband St, Stillwater, OK 74075
The RMA number must be clearly marked on the outside of the package. Please return only defective components. The
return of functioning items increases your return freight charges. Non-defective items will be returned freightcollect to you.
For example,
if a subwoofer is defective, only return the defective subwoofer, not the entire enclosure. Include a copy
of the original receipt with the purchase date clearly visible, and a "proof-of-purchase" statement listing the Customer's
name, Dealer's name and invoice number, and product purchased. Warranty expiration on items without proof-of-
purchase
will be determined from the type of sale and manufacturing date code. Freight must be prepaid; items sent
freight-collect, or COD,
will be refused.
WHAT IS NOT COVERED?
This warranty is valid only if the product is used for the purpose for which it was designed. It does not cover:
o Damage due to improper installation
o Subsequent damage to other components
o Damage caused by exposure to moisture, excessive heat, chemical cleaners, and/or
UV radiation
o Damage through negligence, misuse, accident or abuse. Repeated returns for the same damage may be
considered abuse
o Any cost or expense related to the removal or reinstallation of product
o Speakers damaged due to amplifier clipping or distortion
o Items previously repaired or modified by any unauthorized repair facility
o Return shipping
on non-defective items
o Products with tampered or missing barcode labels
o Products with tampered or missing serial numbers
o Products returned without a Return Merchandise Authorization
(RMA) number
o Products purchased from
an UNAUTHORIZED dealer
o Freight Damage
o The cost of shipping product to KICKER
o Service performed by anyone other than
KICKER
HOW LONG WILL IT TAKE?
KICKER strives to maintain a goal of one week turnaround for all electronics (amplifiers, crossovers, equalizers, etc.)
returns. Delays may be incurred
if lack of replacement inventory or parts is encountered. Failure to follow these steps
may void your warranty. Any questions can be directed to the
KICKER Customer Service Department at [phone].
Contact your International
KICKER dealer or distributor concerning specific procedures for your country's warranty
policies.
Note: All specifications and performance figures are subject to change. Please visit www.kicker.com for the most
current information. 12PX.2-F-20111129
18

INTERNATIONAL WARRANTY
Contact your International KICKER dealer or distributor concerning specific procedures for your country's warranty policies.
WARNING: KICKER products are capable of producing sound levels that can permanently damage your hearing! Turning up a
system to a level that has audible distortion
is more damaging to your ears than listening to an undistorted system at the same
volume level. The threshold of pain
is always an indicator that the sound level is too loud and may permanently damage your
hearing. Please use common sense when controlling volume.
GARANTiA INTERNACIONAL Version Espaiiol
Comuniquese con su concesionario o distribuidor KICKER internacional para obtener infor aci6n sobre procedimientos especfficos
relacionados con las normas
de garantia de su pais.
ADVERTENCIA: Los excitadores KICKER son capaces de producir niveles
de sonido que pueden danar permanentemente
el oido. Subir el volumen del sistema hasta un nivel que produzca distorsi6n es mas danino para el oido que escuchar un
sistema sin distorsi6n al mismo volumen. El dolores siempre una indicaci6n de que el sonido es muy fuerte y que puede danar
permanentemente
el oido. Sea precavido cuando controle el volumen.
La frase "combustible para vivir
Ia vida Livin' Loud™ a todo volumen" se refiere al entusiasmo porIa vida que Ia marca KICKER
de estereos de autom6vil representa y a Ia recomendaci6n a nuestros clientes de que vivan lo mejor posible ("a todo volumen")
en
todo sentido. La linea de altavoces y amplificadores KICKER es Ia mejor del mercado de audio de autom6viles y por lo tanto
representa
el "combustible" para vivir a todo volumen en el area de "estereos de autom6vil" de Ia vida de nuestros clientes.
Recomendamos a todos nuestros clientes que obedezcan todas las reglas y reglamentos locales sobre ruido en cuanto a los
niveles legales y apropiados
de audici6n fuera del vehiculo.
INTERNATIONALE GARANTIE Deutsche Version
Nehmen Sie mit lhren internationalen KICKER-Fachhandler oder Vertrieb Kontakt auf, um Details uber die Garantieleistungen in
lhrem Land zu erfahren.
WARNUNG: KICKER-Treiber konnen einen Schallpegel erzeugen, der
zu permanenten Gehorschaden fuhren kann! Wenn Sie ein
System auf einen Pegel stellen, der horbare Verzerrungen erzeugt, schadet das lhren Ohren mehr, als ein nicht verzerrtes System
auf dem gleichen Lautstarkepegel. Die Schmerzschwelle ist immer eine Anzeige
dafUr, dass der Schallpegel zu laut ist und zu
permanenten Gehorschaden fuhren kann. Seien Sie bei der Lautstarkeeinstellung bitte vernunftig!
Der Slogan "Treibstoff
fUr Livin' Loud" bezieht sich auf die mit den KICKER-Autostereosystemen assoziierte Lebensfreude und die
Tatsache, dass wir unsere Kunden ermutigen,
in allen Aspekten ihres Lebens nach dem Besten ("Livin' Loud") zu streben. Die
Lautsprecher und Verstarker von KICKER sind auf dem Markt
fUr Auto-Soundsysteme fuhrend und stellen somit den "Treibstoff"
fur das Autostereoerlebnis unserer Kunden
dar. Wir empfehlen allen unseren Kunden, sich bezuglich der zugelassenen und
passenden Lautstarkepegel auBerhalb des
AL)tos an die ortlichen Larmvorschriften zu halten.
GARANTIE INTERNATIONALE Version Frant;aise
Pour connaltre les procedures propres a Ia politique de garantie de votre pays, contactez votre revendeur ou distributeur
International KICKER.
AVERTISSEMENT: Les haut-parleurs KICKER ont
Ia capacite de produire des niveaux sonores pouvant endommager l'ou'i'e de
fac;on irreversible ! L'augmentation du volume d'un systeme jusqu'a
un niveau presentant une distorsion audible endommage
davantage
l'ou'i'e que l'ecoute d'un systeme sans distorsion au meme volume. Le seuil de Ia douleur est toujours le signe que le
niveau sonore est trop eleve et risque d'endommager l'ou'1'e de fac;on irreversible. Reglez le volume en faisant prevue de bon sens!
L'expression" carburant pour vivre plein
pot" fait reference au dynamisme de Ia marque KICKER d'equipements audio pour
vehicules eta pour but d'encourager nos clients a faire le maximum (" vivre plein pot") dans tousles aspects de leur vie. Les
haut
-parleurs et amplificateurs KICKER sont les meilleurs dans
le domaine des equipements audio et representent done pour nos
client
le" carburant pour vivre plein pot" dans I' aspect" installation audio de vehicule" de leur vie. Nous encourageons tous nos
clients a respecter toutes les lois et reglementations locales relatives aux niveaux sonores acceptables a l'exterieur des vehicules.
5) stillwaterdesigns
P.O. Box 459 • Stillwater, Oklahoma 7 4076 • USA • [phone]
19

7 11 11 Ullll!t t ll 8
CE:
MAD E IN CH I NA