Kicker KMC2 User manual

Installation
Please read the instruction carefully before operating the unit

Installation
ATTENTIONS OF INSTALLATION
1.This player should be installed by professional technician.
2. Please read the instruction and operation of equipment carefully before
installing.
3. Make sure to connect other wires before power connection.
4. To avoid short circuit. Please make sure all the exposed wire are insulating.
5. Please fix all the wires after installation.
6. Please make connection to the player accordingly to this instruction manual.
Wrong connection may cause damage.
7. This player only fit for 12V DC device and please make sure your car
belongs to this kind of cathode grounding electrical system.
8. Please connect the wires rightly. Wrong connection will cause malfunction or
damage the electrical system.

Installation
WIRING CONNECTION
1. This player can only be used by the 12V DC cathode grounding electrical system.
2. Don’t connect the terminals of the battery until the player is absolutely with well erection
joint.
3. Please make sure to connect the yellow wire to the positive of the battery(+).
4. When change the fuse. Please make sure the specifications are same.
5. Using good quality speaker with 4-8 ohm can result in the best effect of the equipment.

KEY FUNCTION
LOCATION OF KEYS
1 POWER/SOURCE button
1. MENU button
2. PRESETS button
4 Seek up button
5 PAUSE button
6. Seek down button

KEY FUNCTION
Key functions table
Keys
Acti
on
Radio
USB
AUX
BT
Stand
by
PWR
/SRC
Short
Source change
Source change
Source change
Source change
Power
on
Long
Power off
Power off
Power off
Power off
Power
on
PRE
SET
S
Short
Preset (+encoder)
File search (+encoder)
/
/
/
Long
Manual
save(+encoder)
RPT one/RPT all/RDM
on/RDM off
Test mode（5
Seconds）
/
/
MEN
U
Short
BT (pair/conn)-BEEP
(on/off)-LOUD(on/off)
-AREA(USA/EUR)
BT (pair/conn)-BEEP
(on/off)-LOUD(on/off)-
AREA(USA/EUR)
BT (pair/conn)-
BEEP(on/off)-LOU
D(on/off)-AREA
(USA/EUR)
BT (pair/conn)-
BEEP(on/off)-LOU
D(on/off)-AREA
(USA/EUR)
/
Long
BT (pair/conn)-BEEP
(on/off)-LOUD(on/off)
-AREA(USA/EUR)
BT (pair/conn)-BEEP
(on/off)-LOUD(on/off)-
AREA(USA/EUR)
BT (pair/conn)-
BEEP(on/off)-LOU
D(on/off)-AREA
(USA/EUR)
BT (pair/conn)-
BEEP(on/off)-LOU
D(on/off)-AREA
(USA/EUR)
/
<<
Short
Seek down
Previous file
/
Previous file
/
Long
Manual turn down
RF
/
RF
/
>>
Short
Seek up
Next file
/
Next file
/
Long
Manual turn up
FF
/
FF
/
>II
Short
Mute on/off
Play/Pause
Mute on/off
Play/Pause
/
Long
Reset (10 Sec)
Reset (10 Sec)
Reset (10 Sec)
Reset (10 Sec)
/
Enco
der
Rotar
y
Volume up/down
Volume up/down
Volume up/down
Volume up/down
/
SEL
Short
BAS-TRE-BAL-FAD-
EQ
BAS-TRE-BAL-FAD-
EQ
BAS-TRE-BAL-
FAD-EQ
BAS-TRE-BAL-
FAD-EQ
/
Long
BAS-TRE-BAL-FAD-
EQ
BAS-TRE-BAL-FAD-
EQ
BAS-TRE-BAL-
FAD-EQ
BAS-TRE-BAL-
FAD-EQ
/

OPERATION
Turn on/off the unit
Press button to turn on the unit. When the unit is on. Press and hold it for 2 seconds to
turn off the unit.
Sound and setting adjustment
Shortly press VOL knob for the audio menu:
BAS-TRE-BAL-FAD-EQ
Shortly press VOL knob for the setting menu:
BT (pair/conn)-BEEP (on/off)-LOUD(on/off)-AREA(USA/EUR)
In each item rotate the VOL knobto set them.
BT(pair/conn): When paired with the mobile. Choosing “BT PAIR”then press VOL knob to
dis- connect the Bluetooth and prepare to pair another mobile. In this moment, choosing
“BT CONN”then press VOL knob to reconnect the Bluetooth.
BEEP (on/off): Turn on/off the beep sound.
LOUD (on/off): Turn on/off the loudness function.
AREA (USA/EUR): Choose America or Europe region frequency.
Display the clock or information
Shortly press CLK button to show the clock or information.
Reset the unit
Press and hold button for 10 seconds to reset the unit.
Note: When RESET function is activated, all the memory will be lost.
Radio Operation
Receive a radio station
Press SOURCE button to select FM/AM mode. Shortly press / button to receive the
desired radio station. Press and hold / button for manual tuning the frequency.
Manually store station & recall preset station
Receiving a desired station. Press and hold the PRESETS button for 2 seconds. It shows
“SAVE P1”. Rotating VOL knob to select P1~18 then press VOL button. The station will be
saved.
Listening to Saved Radio Memory
Shortly press the PRESETS button then rotating VOL knob to select the presets.
USB Operation
When an USB driver inserted to the unit, the unit will play the MP3/WMA file automatically.
If an USB drive is already inserted in the unit. Keep pressing SOURCE button shortly until
the USB mode display appears.
Select file
Press /button to skip to next/previous file. Hold / button to fast forward
or fast reverse.

OPERATION
Play/Pause
Press button to pause/playing the file.
Search song
Press PRESETS button to select song search mode. Rotating VOL knob to enter numbers.
Press VOL knob to play.
RPT(ONE/ALL)/RDM(ON/OFF)
When playing MP3/WMA, Press and hold PRESETS button for 2 seconds, It shows “RPT
ONE”. Rotating VOL knob to select RPT one/RPT all/RDM on/RDM off.
AUX IN operation
Connecting the signal to the R/L IN connecter behind the unit. Then pressing SOURCE
button to switch to AUX mode.
Bluetooth Operation
Pairing
On mobile phone, select the Bluetooth item searching the Bluetooth device. “KMC
KICKER” should appear in the list, select “KMC KICKER” and then input password “0000” If
it needs a password. When successful paired, the BT mark will be solid (not flashing).
Bluetooth Audio
Press SOURCE button to switch to BT mode. It will play a song of your mobile phone
automatically. Press key to pause/play the song. Press button to select
next/previous song.
Other operation please reference the Key functions table above.

IC Statement:
This device complies with Industry Canada’s licence‐exempt RSSs. Operation is
subject to the following two conditions:
(1) This device may not cause interference; and
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions
suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de
l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d'en compromettre le fonctionnement.
FCC Statement:
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential
installation. This equipment generates uses and can radiate radio frequency energy
and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the equipment.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
IC Radiation Exposure Statement:
This equipment complies with Canada radiation exposure limits set forth for
uncontrolled environments.This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Déclaration d’IC sur l’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux radiations définies
par le Canada pour des environnements non contrôlés.
Cet émetteur ne doit pas être installé au même endroit ni utilisé avec une autre antenne
ou un autre émetteur.