Kid Trax Toys Police Car User manual

ＫＴ１０８１ＷＭ
Ｄｏ ｎｏｔ ｒｅｔｕｒｎ ｔｏ ｓｔｏｒｅ． Ｃａｌｌ ｔｏｌｌ ｆｒｅｅ [phone] ｆｏｒ ａｓｓｉｓｔａｎｃｅ ａｎｄ
ｒｅｐｌａｃｅｍｅｎｔ ｐａｒｔｓ．
Ｔｈｅ Ｏｗｎｅｒ＇ｓ ｍａｎｕａｌ ｃｏｎｔａｉｎｓ ａｓｓｅｍｂｌｙ， ｕｓｅ ａｎｄ ｍａｉｎｔｅｎａｎｃｅ
ｉｎｓｔｒｕｃｔｉｏｎｓ． Ｔｈｅ Ｋｉｄ Ｔｒａｘ Ｐｏｌｉｃｅ Ｃａｒ ｍｕｓｔ ｂｅ ａｓｓｅｍｂｌｅｄ ｂｙ ａｎ
ａｄｕｌｔ ｗｈｏ ｈａｓ ｒｅａｄ ａｎｄ ｕｎｄｅｒｓｔａｎｄｓ ｔｈｅ ｉｎｓｔｒｕｃｔｉｏｎｓ ｉｎ ｔｈｉｓ ｍａｎｕａｌ．
Ｋｅｅｐ ｔｈｅ ｐａｃｋａｇｉｎｇ ａｗａｙ ｆｒｏｍ ｃｈｉｌｄｒｅｎ ａｎｄ ｄｉｓｐｏｓｅ ａｌｌ ｐａｃｋａｇｉｎｇ
ｂｅｆｏｒｅ ｕｓｅ．
４９０２ Ｈａｍｍｅｒｓｌｅｙ Ｒｄ．
Ｍａｄｉｓｏｎ， ＷＩ ５３７１１
Ｕｎｉｔｅｄ Ｓｔａｔｅｓ ｏｆ Ａｍｅｒｉｃａ
Ｐｈｏｎｅ：[phone]
ｗｗｗ．ｋｉｄｔｒａｘｔｏｙｓ．ｃｏｍ
Ｋｅｅｐ ｉｎｓｔｒｕｃｔｉｏｎｓ ｆｏｒ ｆｕｔｕｒｅ ｒｅｆｅｒｅｎｃｅ．
Official Licensed Product
Ｓｔｙｌｅｓ ａｎｄ Ｃｏｌｏｒｓ ｍａｙ ｖａｒｙ
Ｍａｄｅ ｉｎ Ｃｈｉｎａ
Ｄｏｄｇｅ ａｎｄ ＨＥＭＩ ａｒｅ ｔｒａｄｅｍａｒｄｓ ｏｆ Ｃｈｒｙｓｌｅｒ
ＬＬＣ． Ｄｏｄｇｅ Ｃｈａｒｇｅｒ ａｎｄ ｉｔｓ ｔｒａｄｅ ｄｒｅｓｓ ａｒｅ
ｕｓｅｄ ｕｎｄｅｒ ｌｉｃｅｎｓｅ ｂｙ Ｐａｃｉｆｉｃ Ｃｙｃｌｅ Ｉｎｃ．
©Ｃｈｒｙｓｌｅｒ ＬＬＣ２００９
Ｒ
Ｐｏｌｉｃｅ Ｃａｒ Ｏｗｎｅｒ＇ｓ Ｍａｎｕａｌ
©２００９ Ｐａｃｉｆｉｃ Ｃｙｃｌｅ Ｉｎｃ．

For purchasing the Kid Trax Police Car. With the Police Car
your child will have fun and enjoyment for years to come.
Please call us at Kid Trax Toys Consumer Relations at
877-741-6154 with comments or questions. Customer Service
hours are 8AM - 5PM Monday thru Friday CST.
You may also reach us through the following:
Web: www.kidtraxtoys.com
Email: [e-mail]
Mail: Kid Trax Toys
PO Box 344
Olney, IL 62450
Thank You
PREVENT INJURIES AND DEATHS:
NEVER LEAVE CHILD UNATTENDED. ALWAYS keep child in view when
child is in vehicle. Direct adult supervision is REQUIRED.
NEVER use in roadways, near cars, on or near steep inclines or steps,
swimming pools or other bodies of water.
ALWAYS wear shoes.
ALWAYS sit on the seat.
NEVER allow more than two (2) riders in the Police Car.
WARNING

Contents
Safety....................................1
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Charging the Battery - Warnings..................4
Charging the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Install the Front Grill ...........................7
Install the Rear Wheels .........................8
Install the Front Wheels . . . . . . . . . . . . . . . . . . . . . . . . 9
Install the Left and Right Car Doors . . . . . . . . . . . . . . . 10
Install the Dashboard Assembly ..................11
Install the Steering Rod and Steering Wheel . . . . . . . . 13
Install the Rear Section .........................15
Connect the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Install the Car Seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Install the Mirrors..............................18
Install the Front Guard..........................18
Use .....................................19
User Requirements ............................19
Vehicle Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
General .....................................21
Battery......................................21
Troubleshooting Guide .....................25
Services, Repairs and Parts .................28
FCC Information ...........................29
Warranty .................................30
Warranty Limitations ...........................30
Limitation of Damages: .........................30

1
WARNING!
The following safety hazards may result in serious injury or death to the
user of the Police Car:
This product contains small parts that are for adult assembly only.•
Keep small children away when assembling. Remove and dispose
of all protective material and poly bags before assembly. Be sure
to remove all packaging materials and parts from underneath the
car body.
Riding the vehicle without a helmet. Riders must always wear a tted •
helmet that complies with U.S. Consumer Product Safety Commission
(CPSC) Standard CFR 1203.
Battery posts, terminals and related accessories contain lead and lead•
compounds (asic) chemicals known to the state of California to cause
cancer, reproductive harm, and are toxic and corrosive. Never open
the battery.
Body parts such as hands, legs, hair and clothing can get caught in•
moving parts. Never place a body part near a moving part or wear
loose clothing while using the vehicle. Always wear shoes when using
the vehicle.
Using the vehicle near streets, motor vehicles, drop-offs such as: steps,•
water (swimming pools) or other bodies of water, sloped surfaces, hills,
wet areas, ammable vapors, in alleys, at night or in the dark could
result in an unexpected accident. Always use the vehicle in a safe,
secure environment with continuous adult supervision.
Using the vehicle in unsafe conditions such as snow, rain, loose dirt,•
mud, sand or ne gravel may result in unexpected action such as tip
over and skidding.
Using the vehicle in an unsafe manner. Examples include but are not•
limited to:
• Pulling the vehicle with another vehicle or similar device
• Allowing more than two riders
• Pushing the user from the back
• Traveling at an unsafe speed
Always use common sense and safe practices when using the vehicle.
Safety

Parts
234
2
1
56
7
9
bk
bl
bm 9
8
8
bn

1.
Dashboard
2. Steering Wheel
1.
3. Car Seats (2)
4. Rear Section
5. Front Bumper
6. Car Body
7. Front Wheel (2)
8. Wheel Cover (4)
9. Hubcap (4)
10. Car Door (2)
11. Rear Wheel (2)
12. Front Guard
13. Mirror (2)
14. Steering Rod
15. M5 x 25 Screw (2) (included in Side Mirrors)
16. M4.2 x 20 Screw (18)
17. M5 x 57 Screw
(included in Steering Wheel)
18. Large Washer (2)
19. Small Washer (4)
20. Nut (4)
21. Large Nut (4)
22. Hex Wrench
23. Megaphone
24. Battery Charger
25. 12 Volt Battery
Parts List:
3
14 15
16
17 18
19
20
21
23
25
24
22
12V12AH
(included in one package)

Assembly
4
Charging the Battery - Warnings
The following safety hazards may result in serious injury or
death to the user of the Police Car:
WARNING!
Use of a battery or charger other than the supplied Kid Trax•
Toys 12V rechargeable battery and charger may cause a
re or explosion. Only use the supplied Kid Trax Toys 12V
rechargeable battery and charger with the vehicle.
Using the Kid Trax Toys 12V rechargeable battery and•
charger for any other product may result in overheating, re
or explosion. Never use the Kid Trax Toys 12V rechargeable
battery and charger with another product.
Explosive gases are created during charging. Charge the•
battery in a well ventilated area. Do not charge the battery
near heat or ammable materials.
Contact between the positive and negative terminals may•
result in re or explosion. Avoid direct contact between the
terminals. Picking up the battery by the wires or charger can
cause damage to the battery and may result in a re. Always
pick up the battery by it’s case or handles.
Liquids on the battery may cause re or electric shock. •
Always keep all liquids away from the battery and keep the
battery dry.

WARNING!
5
Contact or exposure to battery leakage (lead acid) may cause•
serious injury. If contact or exposure occurs immediately call
your physician. If the chemical is on the skin or in the eyes,
ush with cool water for 15 minutes. If the chemical was
swallowed, immediately give the person water or milk. Do not
give water or milk if the patient is vomiting or has a decreased
level of alertness. Do not induce vomiting.
Battery posts, terminals and related accessories contain• lead
and lead compounds (acid), chemicals known to the State of
California to cause cancer, reproductive harm and are toxic
and corrosive. Never open the battery.
Tampering or modifying the electric circuit system may cause a•
shock, re or explosion and permanently damage the system.
Exposed wiring, circuitry in the charger may cause electric
shock. Always keep the charger housing closed.
Important! Before using the Police Car for the rst time the battery
needs to be charged for a full 24 hours (no more than 30 hours). Only
an adult who has read and understands the following safety warnings
should handle, charge or recharge of the battery (see Maintenance).
Note: It is not necessary to remove the battery from the vehicle for
charging. However, if the adapter cord will not safely reach a 120V
wall outlet, the battery can be removed for charging (see page 22 for
instructions concerning battery replacement).

1. Plug the charger connector into the battery connector on the
battery. Only use the Kid Trax Toys 12V charger included with the
Police Car (Input: AC 120V, 60Hz Output: DC 12V).
2. Plug the charger into a standard 120V wall outlet.
Note: The charger may feel warm during charging. This is normal
and not a cause for concern.
3. After charging is complete (at least 24 hours, but not more than
30) unplug the charger from the wall outlet.
4. Unplug the charger from the battery connector.
1
6
Charging the Battery
2

1. Remove the medium M5 x 30 screw which is attached to the front
end connector.
2. Align the connector over the square metal tubing on the car body.
Push the metal tubing together until the two pieces meet inside
the connector.
3. Insert the same screw that you removed in step one through
the hole in the front grill connector. Once inserted, fasten an M5
screw nut onto the end of the screw.
4. Using M4.2x20 screws, secure the front grill to the car body by
fastening the screws into the five screw hole locations on the car
body. Note: The orientation of the screws are not the same for
each hole location.
7
Install the Front Grill
3
4
2

1
Gear box
Install the Rear Wheels (in clear poly bags)
1. Locate a rear wheel (marked “Rear” with gear-shaped protrusion).
2. Slide the wheel onto the axle with protrusion facing toward vehicle.
3. Fit the gear shaped protrusion into the gear box.
4. Align the three locating pins on the inside of the wheel cover into
the wheel holes, and push the wheel cover into place.
5. Slide a small washer onto the axle.
6. Attach nut onto the axle. Using the Nut Wench, tighten snugly until
you can see about two threads on the axle. Do not over tighten.
7. Align the pins in the hubcap with the holes in the wheel cover.
Press the hubcap into place. Note: Do not use a hammer.
8. Repeat steps 1-4 to attach the other rear wheel.
Side marked
“Rear” with
gear-shaped
protrusion
Back-side of
hubcap with
Locating pins
Rear wheel
2
Wheel cover
4
Small washer 5
Nut 6
Hubcap 7
3
Hubcap
pins
Wheel cover
holes
Wheel holes
8
Axle

Install the Front Wheels (in blue poly bags)
1. Slide a large washer onto the axle. Note: The Washer may
already be on the axle.
2. Slide a wheel onto the axle with FRONT facing toward vehicle.
3. Slide a wheel cover onto the axle, tting the three locating pins
into the holes in the wheel.
4. Slide a small washer onto the axle.
5. Attach a nut onto the axle and tighten snugly with the nut wrench
until you can see about two threads on the axle. Do not over
tighten.
6. Align the pins in the hubcap with the holes in the wheel core.
Press hubcap into place. Note: Do not use a hammer.
7. Repeat steps 1-4 to attach the other front wheel.
Large washer 1
Front wheel 2
Wheel cover 3
Small washer 4
Nut 5
Hubcap 6
Side marked “Front”
faces towards the car
Front axle
9

Bottom of car
door hinge
1
2
Steel
plate
3
Screws
Screw holes
Install the Left and Right Car Doors
1. Slide the bottom of the car door hinge into the car hinge pocket
until the steel plate rests on the recessed area of the car body.
2. Align the holes of the steel plate with the screw holes on the
recessed area on the car body.
3. Screw the plate down using (2) M4.2 x 20 screws (part: #16). Do
not over tighten.
4. Repeat steps 1-3 to attach the opposite door.
Car hinge
pocket
10
Recessed area
of car body

1
Three-prong
connector
attaches to the
steering wheel
Two-prong
connector
attaches to
car body
Megaphone
Megaphone Port
2
11
Install the Dashboard Assembly
1. Plug the Megaphone into the megaphone port located underneath
the Dashboard.
2. Attach the connector under the Dashboard to the connector on the
car body, located at the top of the black, middle stripe.
Note: The connector’s may have slipped inside the Dashboard
assembly during shipment, if so, gently pull the connector out.
Tip: The two-prong connector attaches to
the car body, and the three-prong connector
attaches to the steering wheel. Do not
connect the steering wheel at this time.

3Megaphone bracket
4
4
Dashboard assembly tabs
Dashboard slots
5
12
3. Slide the Megaphone onto the bracket.
4. Open the car doors.
5. Slide the tabs on the front of the Dashboard assembly into the
slots on the car body. Note: Be sure the connector wires are not
separated, pinched or crimped.
6. Align the screw holes of the car body (located by the door hinge)
with the screw holes on the dashboard.
7. Using (2) M4.2 x 20 screws (part:#16), attach the Dashboard
Assembly onto the car body. Do not over tighten.
8. Close the car doors.
6
7
6
7

13
Install the Steering Rod and Steering Wheel
1. Place the vehicle on soft material that will protect it from
scratching or damage. Carefully turn the vehicle onto its side.
Note: It is helpful to have a second person assisting you with
these steps.
2. Insert the Steering Rod through the bracket, the hole in the bottom
of the car body, and up through the dashboard.
Steering rod
2
1
Bracket
Car body
hole
Steering rod
completely inserted

4Steering rod
Raised protrusion
M5 x 57 Screw
6Nut
5
14
3. Attach the wiring harness connector from the Steering Wheel into
the wiring harness connector in the Dashboard.
4. Remove M5 x 57 screw (part: #17) from the Steering Wheel. Insert
the Steering Wheel onto the rod and slide it into the pocket on
the Dashboard. Note: The raised protrusion on the back of the
Steering Wheel column should be facing up. Align the hole for the
screw in the Steering Wheel with the hole in the Steering Rod.
5. Re-insert the M5 x 57 screw through the Steering Wheel and
Steering Rod.
6. Fasten the nut onto the other side of the screw and tighten.
3
Steering wheel connector
Car body connector
Steering rod

Install the Rear Section
1. Align the Rear Section over the four locators on the car body and
lower the Rear Section into place.
2. Using the (7) M4.2 x 20 (part:#16) screws fasten the Rear Section
to the car body. Do not over tighten the screws.
15
Rear body
locator
Rear body
locator
Car body
locator
Car body
locator
Car body
locator
Car body
locator
Rear body
locator
Rear body
locator
2
1

Connect the Battery
Important! Before using the Police Car for the rst time the battery
needs to be charged for a full 24 hours (see page 6 for battery
charging instructions).
1. Fasten the Battery connector to the Main Harness.
2. Place the connectors and wires in the slot (see below).
16
Battery
connector
Main
harness
1
Place battery connector and
main harness in slot
2