KiloVault Uniti Series User manual

KiloVault Uniti
USERS GUIDE
REV 1.1 10/26/2023

Note: � Read this entire document, in addition to the equipment Installation Manual, before installing or using the KiloVault
Uniti. Failure to do so or to follow any of the instructions or warnings in this document can result in electrical shock, serious
injury, or death, or can damage the Uniti, potentially rendering it inoperable.
KiloVault Uniti USERS GUIDE
Registration
Download the KiloVault iT app and Activate the HLX+ series on the web.
This publication could include technical or other inaccuracies or typographical errors. Changes are periodically added to the information herein;
these changes will be incorporated in new editions of the publication. KiloVault® may make improvements and/or changes in the services,
facilities or specifications described in this publication at any time. Please note: If this unit is installed by someone other than the end-user, the installer
must explain the contents of this installation and user’s manual to the end-user.�
REV 1.1 10/26/2023

•Open the box and inspect all contents to ensure all items in the box are
undamaged.
Uniti EcoFreedom 5 - What you received
Inverter Cabinet
Batteries
Battery Cabinet
"DO NOT DISCARD CRATE AND INTERNAL PACKAGING."
REV 1.1 10/26/2023

Install the man body to the base.
Battery Cabinet
Cabinet Base
Prepare the required parts.
1
2
Fix the main body and the base by 10 screws.
3
• Place the battery cabinet of the KiloVault Uniti onto the base. Using the ten bolts provided secure
the Battery cabinet to the base.
Tighten the screws.
4
Installing Base
REV 1.1 10/26/2023

Installing the top cabinet
Battery Compartment
Install the cable box to the top of the main body.
12Tighten the screws.
REV 1.1 10/26/2023

STEP 4
11Each Level are connected in series.
Each level holds (4) HLX+ Batteries.
Installing the Batteries (Uniti Eco Freedom)
•Ensure critical or primary load center is de-energized or disconnected.
•Ensure AC source is de-energized or disconnected.
•Ensure all breakers are off.
Jumper
Jumper
Jumper
Jumper
Jumper
REV 1.1 10/26/2023

Install the side cover
Attach the side cover to the main body.
Slide the front cover in.
a.
Secure the side cover using the provided screws. .
b.
REV 1.1 10/26/2023

120 VAC outlet Breaker.
120 VAC 15 Amp outlet.
120 VAC 15 Amp outlet.
Safety Breakers
Light Breaker Battery String Breakers
Positive Busbar Negative Busbar
Load Breakers. Inverter Breakers.
REV 1.1 10/26/2023

•Before operating the Uniti be sure to read this Setup Guide and the full users manual..
•Even though the inverter is programed before shipping it is critical to program your inverter or charge con-
troller's settings for correct operation, improper programming of your system equipment may invalidate
your battery warranty and could degrade system performance.
Unit Eco Freedom Basic Inverter Settings.
01 Output Source Priority
SOL
PV priority mode, switching to the Mains when the PV fails or the battery is
lower than the set value of the parameter.
02 Output Frequency
60.0 Hz
03 AC Input Voltage Range
APL
Wide mains input voltage range of 230V Machine: 90~280V
Mains input voltage range of 230V machine: 90~280V
04 Battery Power to Utility Setpoint
50.8V
When the parameter [01]=SOL/SBU, the battery voltage is higher than set
value, and the output is switched from mains to the inverter. Setting range:
44V~52V
05 Utility to Battery Power Setpoint
56.0V
When the parameter [01]=SOL/SBU, the battery voltage is higher than set
value, and the output is switched from mains to the inverter. Setting range:
48V~60V
REV 1.1 10/26/2023

SNU Default
PV and Mains hybrid charging: PV charging is a priority, and when
the PV energy is insufficient, the Mains charging supplements.
When the PV energy is sufficient, the Mains charging stops.
NOTE:
Only when the Mains bypass output is loaded, the PV charging and
the mains charging can work at the same time. When the inverter
is in use, only the PV charging can be started.
06 Charge source priority
07 Max charger current
80A default
Max charger current (AC charger + PV charger)
Setting range: 0~80A
08 Battery Type
[08]
Use User-defined; all battery parameters can be set.
09 Battery Absorption charge voltage
56.4V
10 Battery Absorption charge time
5 Minutes
11 Battery float charge voltage
53.6V
12 Battery over discharge voltage
48V default
13 Battery over discharge delay time
5 SEC default
14 Battery under voltage alarm
50.4V
15 Battery discharge limit voltage
50.0V
16 Battery equalization enable
DIS Equalizing charge is disabled
Inverter Settings
REV 1.1 10/26/2023

KiloVault® Uniti Series
Pre-wired energy storage system
KiloVault* LLC
330 Codman Hill Road Boxborough,
MA 01719 [phone]
[email protected].kilovault.com

KiloVault Uniti
USERS GUIDE