Kinco SZ7 Service manual

dingh
1.1 环境要求
工作环境温度：SZ7 系列人机界面的设计规范可以保证它能够在 32℉~122℉（0~50℃）的大多数
工业环境中稳定工作。NEMA 防护规定：SZ7 系列人机界面的前面板符合 NEMA1 的防护规定。
1.2 电源要求
输入电压：DC16V～DC32V；
特别需要注意与变频调速器和开关电源供应器保持较远的距离，这类设备的输入和输出电缆都必
须采用屏蔽电缆，并将屏蔽网接到系统的星形接地点；
直流电源必须与交流主电源正确的隔离开；
不要让 SZ7 系列人机界面和感性负载或控制器的输入电路共用电源。
2.1 尺寸图
2.2 安装方式说明
2.2.1 支架固定
2.2.2 悬挂式安装
注：本产品出厂仅提供 M4 安装螺钉，见包装纸盒，如上支架和钣金挂件为示意图，仅供参考，用户需自行定制。
功能
SZ7
SZ7S
SZ7E
SZ7ES
RS485
√
√
RS232
√
√
√
√
以太网口
√
√
USB HOST
√
√
√
√
注： 1.RS485 、 RS232 、以太网口都集成在 14 芯屏蔽电缆内。
2. 型号后缀为 S 表示产品带握持开关，为 E 表示支持以太网通讯。
3.1 RS232 串口
RS232 串口可用于 SZ7 系列人机界面的编程和调试。
3.2 USB HOST 接口
连接
连接 USB 接口设备或 U 盘
端口作用
连接 USB 接口键盘、鼠标、打印机等，插入 U 盘上传/下载程序以及存储数据
3.3 RS485 串口（SZ7 和SZ7S 支持)
注：在 Kinco HMIware 中创建工程时， SZ7 和 SZ7S 共用一个元件图标。
3.4 以太网接口(SZ7E 和SZ7ES 支持)
以太网接口为 10M/100M 自适应以太网端口。
连接
14 芯屏蔽电缆的灰、红、黑、黄色线（见下文线缆具体说明）
端口作用
用于 HMI 组态的上/下载，系统参数的设置和在线模拟；构成多 HMI 联机；与 PLC
等通过以太网通讯；通过以太网口与 PC 机通讯
注：在 Kinco HMIware 中创建工程时， SZ7E 和 SZ7ES 共用一个元件图标。
4.1 进入模式选择界面操作说明
触摸屏上电前用手指按住液晶屏不放，给触摸屏上电，待触摸屏自动进入模式选择界面之后方可松
手，根据模式选择界面提示进入相关操作。如果在进入模式选择界面 20S 内没有有效操作或无操作，系
统将自动进入触控校正界面。
4.2 模式选择界面功能菜单说明
进入模式选择界面会弹出一个启动菜单对话框，详细功能模式说明如下：
系统设置：单击此按钮，系统进入设置界面，在此画面中可以设置开机启动画面，屏保时间，蜂
鸣器声音，以及亮度调节，设置完成后，可单击 Restart 按钮重启触摸屏。
固件更新：单击此按钮，系统进入固件更新画面，在此画面中可以进行固件更新工作，一般用户
请不要使用此模式。
触控校正：单击此按钮，系统进入触摸屏校正画面，校正成功后会自动重启。
停止倒计时：单击此按钮，控制 20S 倒计时启停。
备注：在模式选择界面的右上角有一个多语言切换按钮，单击此按钮可进行中英文切换。
5.1 线缆信号说明
此系列产品为方便客户使用，提高产品稳定性，采用了 14 芯屏蔽电缆，两两对绞。
标配电缆长 5 米。
注：1.握持信号（常开）、自动(AUTO)、远程(REMOTE)等选择后，都将与公共地导通。
2.急停开关（常闭）按下后，急停信号与公共地断开，恢复后重新导通。
3.急停开关、握持开关、三选择开关的额定电压为 DC24V，额定电流为 0.35A。
5.2 超五类网线插座模块使用说明
SZ7E 和SZ7ES 型号产品具有以太网口功能，出厂时按照 T568B 标准接线，如下：
1--黄色线
2--黑色线
3--红色线
6--灰色线
其中 1、2、3、6指超五类网线插座模块上的编号，对应的线缆是指 14 芯屏蔽电缆内的线序。
《人机界面售后服务条款》请登录如下网址查看：http://www.kinco.cn
连接
14 芯屏蔽电缆的灰色、红色线（见下文线缆具体说明）
端口作用
用于连接 HMI 和具有 RS485 通讯端口的控制器
SZ7 系列机器人手持终端
安 装 说 明
深圳市步科电气有限公司
电话：[phone]
传真：[phone]
技术支持热线：400-700-5281
http：//www.kinco.cn Email：[e-mail]
步科官方微信 地址：深圳市南山区高新科技园北区朗山一路 6 号一栋
1.安装注意事项
2.产品安装
3.通讯连接
在以下场所使用时请采取屏蔽措
施：
有静电或其它形式噪音处
有较强电磁场的场所
可能暴露于射线的场所
靠近于动力电源的场所
请勿在以下场所使用：
阳光直射处
周围温度和相对湿度超出规格的场所
温度急剧变化易引起结露的场所
有腐蚀性气体和可燃性气体的场所
尘埃、灰尘、盐分、铁粉较多的场所
会被溅到水、油、药品等飞沫的场所
给主机带来直接振动和冲击的场所
产品背面预留了 4个75*75mm 的M4 螺纹孔，通过如
左图示的支架，将支架的孔位与螺纹孔对齐，拧入 M4
规格的螺丝后固定在支架上。
4.工作模式
5. 14 芯屏蔽电缆具体说明
通过左图示意的挂件结构，用 M4 规格的螺丝固定在后
壳处预留的上方二处孔位，即可悬挂在理想位置操控。
6.售后服务
连接
14 芯屏蔽电缆的绿色、棕色、粉色线（见下文线缆具体说明）
端口作用
上/下载用户组态程序、HMI 系统固件更新、 通讯

1.1 Environmental Requirement
Operating temperature: SZ7 Series HMI can work stably in most industrial environments that the
temperature between 32°F to122°F (0~50°C).
NEMA rating: This Series HMI is NEMA 1 rated in front panel.
1.2 Power Requirement
Input voltage:DC16V～DC32V.
Particularly note that there must be enough distance between this product and converters or switch
power supply. Make sure that the input and output cables of that kind equipment are shield cable
and the shielding network is connected with the ground.
Make sure that the DC power and AC power is isolated.
Do not use same power supply with the input circuit of inductance load or the controller.
2.1 Dimensional Drawing
2.2 Installation Instructions
2.2.1 Rack Mounting
2.2.2 Hanging Mounting
NOTE ： There are only M4 installation screws in the packaging carton. The rack and the sheet metal
pendant are just schematic diagrams, needed to customize by customers.
Function
SZ7
SZ7S
SZ7E
SZ7ES
RS485
√
√
RS232
√
√
√
√
Ethernet
√
√
USB HOST
√
√
√
√
Note ： 1.RS485 、 RS232 、 Ethernet are integrated in the 14-core shielded cable.
2. The Suffix of S indicates that products with hand holding switch, E is for Ethernet port.
3.1RS232 port
RS232 port is used to program and debug.
3.2 USB HOST
Connection
Connect with USB interface devices or U disks
Port
Function
This interface can be connected with USB keyboard, mouse and printers, and the
U disk can be used for user’s configuration uploading/ downloading as well as
data storage.
3.3RS485 port (SZ7 and SZ7S Support)
Note ： When you create a project in Kinco HMIware SZ7 and SZ7S share a component icon.
3.4 Ethernet (SZ7E and SZ7ES Support)
Ethernet interface can adaptive 10 M/ 100 M.
Connection
Grey/red/black/yellow in the 14-core shielded cable (see below)
Port
Function
The port can be used for uploading/downloading HMI program, setting
system parameters and online simulation. It can connect multiple HMIs via
the Ethernet; it can communicate HMI and PLC via the Ethernet, as well as
communicate with a PC via the Ethernet port.
Note ： When you create a project in Kinco HMIware,SZ7E and SZ7ES share a same icon
4.1 Instructions for entering Operation Mode selection window
Hold pressing on the touch panel when you power on HMI, then HMI will enter operation mode
selection window, select the operation mode according to your application. If there is not any operation in
20 seconds after entering operation mode selection window, HMI will enter application (normal working)
mode automatically.
4.2 Descriptions of functions in Operation Mode selection window
After entering operation mode selection window, it will pop up a menu. Follows are the descriptions of
the functions in the menu:
System Setup：Press this button to enter system setup window. This window is used to set initial
window, screen saver time, buzzer and brightness adjustment. After setting, press Restart button to
restart HMI.
Firmware Update：Press this button to enter firmware update mode. This window is used to update
firmware. Normally this mode is not advised to use without guiding by manufacturer.
Touch Calibration ：Press this button to enter touch calibration window. It will restart HMI
automatically after calibration successful. There is a timer in this button, it will enter application window if
there is no operation within 20s.
Stop timer: Press this button to stop the 20s timer.
Note: There is a multi-languages button; it is used to switch English and Chinese.
5.1 Detailed description of the14-core shielded cable
SZ7 series HMI adopt 14-core shielded twisted cable to improve product stability.
The standard length of cable is 5 meters.
Note ： 1.Handhold signal （ NO ）、 AUTO-Signal 、 Remote-Signal are connected with common ground
when they are selected.
2.When emergency switch （ NC ） is pressed down ， it is disconnect with Common Ground.
3. Rated voltage is DC24V,rated current is 0.35A,included emergency switch 、 handhold switch and
3-position selection switch .
5.2 UTP Cable Socket Module Instruction
SZ7E and SZ7ES have Ethernet interface，the wire connection is in accordance with the T568B
standard，as follows：
1--yellow
2--black
3--red
6--grey
Pin 1, 2, 3, 6 are the pin number on the UTP Cable Socket Module, the color above is the wire
color in 14-core shielded cable.
For < Service Terms and Conditions for HMI >, please check :http://www.kinco.cn
Connection
Green/brown/pink in the 14-core shielded cable(see below)
Port
Function
The port is used to upload/ download user configuration program to the
HMI to set HMI system parameters and to communication.
Connection
Grey/red in the 14-core shielded cable(see below)
Port Function
This port is used to connect the controller with RS-485port.
SZ7 series Teach Panel
Installation Instruction
Kinco Electric (Shenzhen) Ltd.
Tel：[phone]
Web: www.kinco.cn Email：[e-mail]
Add: Building 1, No. 6 Langshan 1st Rd, Hi-tech Park
KincoWeChat North, Nanshan, Shenzhen, China.
1.Installation Note
2. Installation Description
Please take shielding measures
in the following places:
Places that exist electrostatic
or other kinds of noise
Places of strong
electromagnetic
Places that may be exposed
to rays
Places near the power
Please do not use in the following places:
Places direct in sunlight
Surrounding temperature and humidity beyond the
specifications
Places of temperature changes sharply and easily
cause condensation
Places that exist corrosive gas and combustible gas
Places of much dust, dirt, salt and iron powder
Places that will be splashed water, oil and drugs
Places that bring direct vibration and shock to host
3. Communication connections
On the back of the product, 4 M4 75*75mm thread holes are
reserved, and the hole position of the bracket (refer to the left)
is aligned with the thread hole, and the screw is screwed into
the M4 specification.
5. Detailed description of the14-core shielded cable
Through sketch left hanging structure, specifications of the M4
screws fixed in the shell reserved above two holes, can be
suspended in a desired position control.
6. After-sales Service
4. Operation Mode