Kind KD-WH150M User manual

USER MANUAL
Model：KD-WH150M
Thank you for choosing KIND
product, please read this user
manual throughout before
using.

Preface
1. All internal technologies of this product are protected, Including device, software and trademark. Reproduction in
whole or in part without written permission is prohibited.
2. ALL brands and trademarks Are protected and other relative trademarks in this user manual are the property of their
respective owners.
3. Due to constant effort of product development, KIND reserves the right to make changes and improvements to the
product described in this manual without prior notice.
4. Not cover the following:
⑴Physical damage to the products
⑵Any damage or breakdown caused by use, maintenance, or storage not according to the user manual’s
introductions.
⑶The attenuation of signal quality resulting from being used in any special environments.
⑷Any damage caused by not powering the product by package supplied power adaptor.
⑸Any damage or breakdown not caused by the product’s design, workmanship, manufacturing, quality, or
unauthorized repairs or parts replacement or other operations.
5. For any suggestions and requirements on this product, please contact us, please contact us through phone, fax, Email,
etc.

Safety Precautions
Please follow the safety precautions before using . The following conditions are not covered by warranty.
1. Unauthorized repairs or other Unauthorized operations.
2. Inappropriate placement including but not limited to lighting, fire, exposure to rain, water or gas.
3. Using the wrong power supply
Warning
Do not get any liquid inside the products
Do not block the ventilation openings or put substances inside, in order to avoid short circuit,
fire or electric shock.
Do not place the product in the rain or moisture to avoid electric shock or fire.
Danger
Switch the power off before connecting other devices.
Power socket: Make sure the power socket under the voltage range of the product to avoid short circuit,
electric shock and fire.
Power cable: Make sure the power cable is not pressed or tightened by any items or weights.
Power Load：Do not exceed the load on the wall outlet, extension cable or other porous receptacle to avoid fire
or electric shock.
Lightning: Disconnect the power cable if it is lightning or not using in long period of time.
Working environment
Please don’t lay the product on any unstable place to avoid fallen damage.
Please don’t use the product in a place overheating, undercooling or with lots of moisture, or nearby strong
magnetic devices.
Please don’t lay the product on metal shelf, in order to ensure the effective wireless transmission.
Packing list
1. Transmitter 2.Receiver 3.Antenna*44.D-tap to lockable pole cable（0.6m）
5. Power adaptor 6.User manual

1. Product Introduction
This model includes transmitter and receiver，adopts the latest encrypted transmission technology，Supports
HDMI wirelessly transmitted in 150 meters scale(Line-of-sight), 1 channel HDMI digital video transmission, auto
pairing. It is equipped with DC power connector, compact size, portable, and the receiving signal is very stable.
2. Features
HDMI Wireless transmission
Support up to 1080P50/60Hz HDMI wireless transmission.。
150 meters transmission distance
In open outdoor area, the effective transmission distance is approx. 150 meters (line of sight).
Wireless frequency
The system adopts 5180~5220MHz and 5760~5820MHz Wireless frequency band
Frequency Band and Frequency point
CH00
5180MHz
CH04
5780MHz
CH01
5200MHz
CH05
5800MHz
CH02
5220MHz
CH06
5820MHz
CH03
5760MHz
/
/
The system adopts 5182.5~5282.5MHz and 5762.5~5822.5MHz Wireless frequency ban
Frequency Band and Frequency point
CH00
5182.5MHz
CH04
5782.5MHz
CH01
5202.5MHz
CH05
5802.5MHz
CH02
5222.5MHz
CH06
5822.5MHz
CH03
5762.5MHz
/
/
Pairing mode
Support auto pairing connection and manual switching of frequency points.
Encryption
Support AES 128-bit encryption to protect the transmission.
All-Metal Shell
Both the transmitter and receiver adopt metal shell which is durable and solid.
All hardware design
The wireless system is hardware and plug-and-play designed, without installing software, easy to
set up.

Remark:
1. The transmission distance may be different, and depend on surroundings, radio wave conditions,
buildings, etc., the 150 meters transmission distance may be not guaranteed.
2. The wireless transmission might be interrupted if there’re other devices of 5Ghz wireless bandwidth
used in the same location.
3. Signal reception may be affected by the position, height and angle of devices. If reception video
is not stable, please physically adjust placement for the optimized signal.
4. Set the antennas straight up and set receiver higher to enhance the transmission efficiency.
3. Appearance Instruction
Transmitter
⑴Antenna
⑵Product label
⑶Link：Wireless status indicator
⑷Video：Video signal indicator
⑸Power：Power status indicator
⑹Pair：0.96-inch OLED
⑺Installation thread：1/4”-20 thread. Use the package supplied articulating arm trestle to install the device to the
camera.
⑻USB：Micro USB，software upgrade interface
⑼HDMI in：HDMI input (standard HDMI-A type connector).
⑽Battery plate：”F” plates can be used. compatible with SONY ”L” series NP-F770/970/.
⑾HDMI LOOP：HDMI loop out (standard HDMI-A type connector).

⑿ON/ OFF：Power switch
⒀DC in：Support DC 7～17V input,5.5mm(outer diameter)/2.1mm(inner diameter)
Outside: negative, Inside: positive
The description of LED status indicator
Receiver
⑴Antenna
⑵Product label
⑶Link：Wireless status indicator
Device
LED indicator
Status
Description
Transmitter
Power
Constant on
Power connected and switched on
Off
Power disconnected and switched off
Video
Constant on
There is recognizable video signal input
Flash
There is no recognizable video signal input
Link
Constant on
The wireless network connection is normal
Flash
The wireless network connection is abnormal

⑷Video：Video signal indicator
⑸Power：Power status indicator。
⑹Pair：Pair button。
⑺Installation thread：1/4”-20 thread, Use the package supplied articulating arm trestle to install the device to
the camera
⑻USB：Micro USB，software upgrade interface
⑼HDMI OUT：HDMI output (standard HDMI-A type connector).
⑽Battery plate：”F” plates can be used. compatible with SONY ”L” series NP-F770/970/.
⑾HDMI OUT：HDMI output (standard HDMI-A type connector).
⑿ON /OFF：power switch
⒀DC in：Support DC 7～17V input,5.5mm(outer diameter)/2.1mm(inner diameter)
Outside: negative, Inside: positive
The description of LED status indicator
4. Setup connection
⑴ Connect the HDMI in interface of transmitter to the HDMI out of the camera or video output device.
⑵ Connect the HDMI out interface of receiver to the HDMI in of the monitor or switch station.
⑶ Connect the power supply of transmitter and receiver, the “power” indicator will light up,“Link”
and “Video” indicator light up when the transmitter and receiver have identifiable signal inputs and
connections，“Link” and “Video” indicator will flash if transmitter and receiver have no identifiable
signal input。
Tips：1.put the power switch to “ON” when connect the power supply of transmitter and receiver.
2. The transmitter only supports the HDMI video input interface, and the system automatically
detects the input video interface。
5. Pairing
⑴ Connect the HDMI in interface of transmitter to the HDMI out of the camera or video output device.
⑵ Connect the HDMI out interface of receiver to the HDMI in of the monitor or switch station.
⑶ Connect the power supply of transmitter and receiver, the “power” indicator will light up “Video”
and “Link” indicator will flash.
⑷ Long pressing the “pair” button in both transmitter and receiver，The “Link” indicator of
transmitter and receiver flash and pair, “Link” indicator lights up，the automatic pairing is successful
and enters the encrypted transmission state.
(5) Press the “Pair” button twice apartly to upgrade the firmware, the “Video” indicator quickly flashing during upgrade
process，“Video”“Link” indicator light up with red, the firmware upgrade successfully. The “Video”“Link”indicator
flash when upgrade is failure
Device
LED indicator
Status
Description
Receiver
Power
Constant on
Power connected and switched on
Off
Power disconnected and switched off
Video
Constant on
There is recognizable video signal input
Flash
There is no recognizable video signal input
Link
Constant on
The wireless network connection is normal
Flash
The wireless network connection is abnormal

Tips：1.When pairing, the transmitter and receiver need to be paired
Simultaneously.
2.During normal use, ensure that the wireless device used has been paired and successfully paired.
3.The paired transmitter and receiver will be automatically connected after booting up. It is no
need to pair again.
4.Please keep the transmitter and receiver in distance of 1-2m to avoid pairing failure.
6. The way to get the best effective of Wireless Transmission
⑴ Set the antenna on both transmitter and receiver vertically straight up. No request to spread.
(Fig.1)
Fig.1

⑵ Set the receiver as high as possible to avoid interference.

⑶Avoid walls, trees and water to reduce signal attenuation.
7. Trouble shooting
If the receiver failed to output video correctly, the possible causes are as below; please find the solution
from following chart:
The receiving
video
Possible causes
Soultion
No display
The transmitter or the receiver is not
powered on
Check power connection and switch on
the transmitter and receiver
The antennas are not installed
properly and screwed tightly
Install the antennas properly and screw
tightly of both transmitter and receiver
Bad connection of video cable
Check video cable connection of both
transmitter and receiver
Video format is not supported
Change the output video format of the
camera
Poor Video quality
Bad connection with video cable
Reconnect reliably
The wireless transmission is disturbed
by environment
Wait for 1 minute or reboot the
transmitter and receiver
The transmission distance is out of
effective range
Put the transmitter closer to the receiver

8.Specification
FCC Statement
Any Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired
operation.
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment .
This equipment should be installed and operated with minimum distance 20cm between the radiator& your body.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates,uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the equipment off
Model
Transmitter
Receiver
Input
HDMI×1
/
Output
HDMI×1
HDMI×2
Video format
1080I（60∕59.94∕50）∕720P（60∕59.94∕50)∕1080P（60∕59.94∕50∕30
∕29.97∕25∕24∕23.98）
Wireless
frequency
FULL:5180-5220MHz and 5760-5820MHz
Modulation
mode
OFDM Support 16QAM、64QAM、QPSK、BPSK modulation mode
Transmission
distance
150m（Line of sight）
Power
consumption
≤7.5W
≤7W
Input voltage
DC∕Battery：7～17V
DC∕Battery：7～17V
Working
environment
Temperature：0℃~+40℃
Dimension
114.18×69.55×28（mm）
114.18×69.55×28（mm）
Net weight
（Without
antenna）
190.7g
193.3g
Net weight（With
antenna）
198.6g
201g

and on, the user is encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.
Beijing kind Network Technology Co. LTD
Address: 16C, Unit 1, Building C, Yingdu PLAZA, No. 48, Zhichun Road, Haidian District, Beijing,China.
Official website:WWW.KINDLIVECAST.COM
Zip Code: 100086
Phone: [phone]