King Champion KP-100i User manual

S TA N D B Y R E P LY B A C K
User Manual
Internet Radio With iPod docking
1 2 3
King Champion
KP-100i
Please read this user manual carefully before using the receiver.

LOCATION OF CONTROLS
1 2 3
STAN D B Y R EPLY BA C K
L A N
4
8
D C 9 V
5 6 7
1 2 3
1. Standby
2. Reply
3. Back
4. LCD Display
5. Play/Pause/Stop
or
Preset 1
6. Previous or Preset 2
7. Next or Preset 3
8. Tune/ Volume/ Select
Key Functions:
9 10 11 12
9. LAN Jack
10. Audio Output
11. Earphone Socket
12. DC Socket
BACK: Press to go back to the previous display.
REPLY:
Reserved for future services.
1, 2 , 3 : Use to store and play up to the radios.
: Press to pause or playback and hold to stop playback.
: Press to start playback at the previous track.
: Press to start playback at the next track.
Tune/ Volume: Use to search for stations, use to change the option shown
on
the display, Use to adjust the volume.
Stanby: Press to switch the internet radio Stand By on/off.

Note: This equipment has been tested and found to comply wit the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules, These
limits are designed to provide reasonable protection against harmful
interference in a residential installation, This equipment generates, uses
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications, However, there is no guarantee that interference will not
occure in a particular installation, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for
help.”
“To comply with FCC RF exposure compliance requirements, a separation
distance of at least 20 cm must be maintained between the antenna of this
device and all persons. This device must not be co-located or operating in
conjunction with any other antenna or transmitter.”
INTERNET
SERVICE
Configuring
‘My
Stuff’
Registering an account on Reciva’s website
1. Open the website, http://www.reciva.com, from your internet browser.
2. Click on the ‘My Account’ link and follw the on-screen instructions to register
an account. Please note, during the registration process, a validation code
will be sent to you via email. Please enter this code when prompted to do so.
3. After logging into your account, you will be able to edit your information for ‘My
Stations’,’My
streams’, ’My Detail’ and “My Radios” from the ‘My Account’
section.
4. You can now add your Internet Radio to your account on the website by
accessing
the ‘My radios’ link. From the ‘My Radios’ section, you will need to
enter
in your radio’s eight-digit serial number, which can be found from the
‘Configure> Version’ menu on the radio, and you will also need to enter in your
radio’s
registration code-which can be found from the ‘Configure> Register’
menu
on the radio.
Configuring ‘My stations’

1. It’s possible to search for radio stations that are available in Reciva’s
stations’ database from Reciva’s Website. When ever stations are
searched for on the website, then will be displayed in a list of search
results together with a link to
‘Add to my stations’.
2. Clicking on the ‘Add to my stations’ link, will add the station to your account’s
‘My stations’ list. This list can be edited by clicking on ‘My stations’ under the
‘My account’ section on the website.
3. Once you have internet station available in you ‘My stations’ list, you may play
these
stations from your Internet Radio. These stations will be available on
your radio from the menu item:’ Stations>My Stuff> My stations’. Please note ,
the
stations will only be available to your radio once your radio has
downloaded a new stations’ list. To cause the radio to download a new
stations’
list immediately, please remove and reconnect the power to your
radio.
Configuring ‘My Streams’
1. once logged into your Reciva website account, you can add your own
internet radio streams to the ‘My streams’ section, which is listed under the
‘ My account’ section
2. Clicking on’ My streams’ sill prompt you to enter the station’s name and its
media
stream URL. The media stream URL should be a link to a website’s
actual
audio stream. If you have any doubt about locating the media
stream URL from a webpage, then please refer to the FAQs section on
Reciva’s website, http://www.reciva.com
3. Once you have Internet radio streams available in you ‘My streams’ list,
you may play these stations from your internet radio. These station will be
available on your radio from the menu item:’ Stations >My stuff> My streams’.
Please
note, the streams will only be available to your radio once your radio
has
downloaded a new station’ list. To cause the radio to download a new
stations’
list immediately, please remove and reconnect the power to your
radio.

SETTING UP
Those steps for connecting your radio to your network
Step 1- Switching on the radio;
Plug the cable from the AC adapter into the socket labeled 9V DC on the back of
the
radio, then switch on at the mains.
Caution: Use only the mains adapter supplied with the radio. Connecting a power
supply
with a different rating will cause permanent damage to the radio and may
be hazardous.
The display on the front of the radio will light up and say:
Internet Radio
Then
Reciva Enabled
ARM Powered
After a few seconds, this will change to show:
Finding Gateway
Step 2 Connect to the network;
Note: At first, you need to select network;
(1) Press the SELECT button;
(2) Turn the TUNE until the display says<Configure>;
Configure
(3) Press the SELECT button;
(4)Turn the TUNE until the display says<Network Config>;
Network Config
-1-

(5)Press the SELECT button;
(6)Turn the TUNE until the display says<Wired/Wireless>;
Wired/Wireless
(7) Turn the TUNE until your appropriate equipment;
Autio wired
only wireless only
If you select Auto , it will be select automatically.
If you select Wired Only, It will be only used for Wired Ethernet.
If you select Wireless Only, It will be only used for Wireless Wi-Fi connection.
(8) When the ESSID for the access point you want to connect to be displayed on
the
screen, press the SELECT button. You might need to enter the correct
WEP(Wired
Equivalent Privacy) or WPA(Wi-Fi Protected Access) code. If your
network
is not configured to need a WEP or a WPA code.
The display will show:
Network OK
If the screen displays:
Encryption Key
Required
Then the network is using one of the encryption systems:
Wired Equivalent Privacy (WEP) or Wi-Fi protected Access (WPA). You
therefore
need to enter the correct WEP or WPA code into the radio for it to
communicate
with you network.
Note:
The encryption code would have been set up by the person who set up and
configured
your network.
After 3seconds the display goes into the code entry mode or press select.
-2-

Note
If the display does not automatically go into code entry mode, press the
SELECT button. To enter the code, use the TUNE to select each character of
the code in turn, pressing the SELECT button after each character.
Note
Make sure the character you want is shown in the centre of the display to be able
to
select it.
< {}~ END < > 0
The display shows “ Connecting to network” as the radio connects to the network. :
Connecting to
network
Then it will be displayed:
Network OK
Note:
<How to scan for networks>
(1) Press the BACK button;
(2) Turn the TUNE until display says <Configure>;
Configure
(3) Press the Select button;
(4) Turn the TUNE until display says<Network Config>
Network Config
(5) Press the Select button;
-3-

(6) Turn the TUNE until display says<Scan for network>;
Scan for network
(7) Press the SELECT button to be Scanning the network;
(8) Then turn the TUNE to select your appropriate equipment;
THEN:
Connecting to
network
Network OK
Note
We advise that you switch the power off, before connecting or disconnecting any
external
accessories.
-4-

USING THE PRODUCT
Choosing a radio station to listen to
When playing a stream, the Internet Radio, downloads a small amount of the
stream before it starts playing. This will occur before your selected station starts to
play.
1. With <Station> the highlighted menu, press the select button.
Stations
Or if the screen does not display<stations>, turn the TUNE until it does and then
press the SELECT button.
2. Turn the TUNE to choose from <Location>or <Genre>. <Location>enables
you to choose a Continent and then a country from that continent. You can then
select
from a list of radio stations from your chose country. <Genre> enables
you to choose radio stations according to their content, for example 90s,
Classical,
Dance or Rock.
3. Press the Select button to choose the option you want:
Genre
A ,Turn the TUNE until the display shows the type of music you want to listen to
(e.g. Rock)and press the SELECT button.
B, Turn the TUNE until the display shows the station you want and press the
SELECT button.
Or:
location
A, Turn the TUNE until the display shows the continent you want and then press
select(or select ‘all’ to display all countries).
B, Turn the TUNE until the display shows the country you want and press the
SELECT button.
loading
-5-

Above screen Is displayed, while the station are buffering. Then the first available
station
name is displayed.
Choosing iPod to listen to:
Instructions for iPod:
1. Select iPod on the radio. Switch on the internet radio and press Back until
you are at the top level menu. Turn the TUNE until iPod is displayed highlight
and press the SELECT button
2. Press Back exit the Ipod Mode;
3. Turn the encoder clockwise and anti-clockwist to adjust the Volume up/down ;
4. Press Play button to palyback the iPod streaming, press Prev/Next to
playback previous and next tracks, and Press and hold the Prev/next to
playback the streaming fast forward and fast rewind;
5. Press Select encoder and hold 3sec, it will enter into iPod menu nevigation
mode; It can be operated the iPod menu by using the buttons of the radio;
1. Press and Hold 3 seconds to exit the Ipod nevigation mode;
Note: It couldn’t tune the volume down/up when menu nevigation mode!
iPod
iPod
Menu Mode

Changing the volume:
You can change the volume by turning the TUNE clockwise to increase the
volume and anticlockwise to decrease the volume. The display shows the
volume bar. You cannot change the volume when you are in a menu or when the
radio is connecting to a station.
Storing a radio station in a preset by the front panel control:
When a radio station is playing, just hold down one of the preset buttons to store
the
station.
E.g. to store preset1: press and hold the preset
Assigned to
Preset 1
Playing a preset radio station When a radio station is playing, briefly press the
preset button ( , , ) for the station you want.
Storing a radio station in a preset by the front remote control:
To store a preset, you must first be listening to the station that you
would
like to save, then press STORE button. Then press the preset
number you would like to save and allow 2 seconds to store the station
into the preset. The LCD will then show <Assigned to preset #>.
Once you have saved a station to one of the presets, you can recall it by pressing
RECALL
button. Then press the preset number you would like to recall and the
radio
will connect to your station that you recalled.
Requesting a station that is currently unavailable on-line
If you want to listen to a particular radio station which is currently not available on
line,
you can visit the Reciva website at http://www.reciva.com/ and put in a
request to add the station to the list.
Switch the radio OFF and ON
-6-

To switch off, press STANDBY once and the clock will be displayed. To switch
on, press STANDBY once and the radio will take up to 60 seconds to start
playing again, as it finds the radio station you were last connected to and loads
it into the buffer.
Setting the CLOCK
1. Press the BACK button.
2. Turn the TUNE until the display says<Configure>.
Configure
3. Press the SELECT button.
4. Turn the TUNE until the display says<Clock>.
Clock
5. Press the SELECT button.
6. Turn the TUNE until the display say<Set Time>.
Set Time
7. Press the SELECT button
Set Time
12:10
8. Turn the TUNE until the hour setting is correct, then press the SELECT button.
Set Time
13:10
9. Turn the TUNE until the minute setting is correct, then press the SELECT
button.
Set Time
13:11
-7-

The display says Time Set with the new time shown beneath for 3 seconds, and
then
returns to the radio station display.
Setting the ALARM
1. Press the BACK button.
2.ROTATE the TUNE until the display says <Alarm clock>
Alarm Clock
3. Press the SELECT button.
4. Turn the TUNE until the display says<Set Alarms>.
Set Alarms
5.You can select Disable all to delete all the alarm setting, or you can set up to 5
alarms in the radio.
6.Rotate the TUNE to 1 group of clock alarm setting, then press the SELECT
button.
Enable Alarm
Yes/No
7. After you select ‘ Yes’, you are able to rotate the TUNE until the hour setting is
correct, then press the SELECT button.
Set Alarm
7:12 AM
8. Rotate the TUNE until the minute setting is correct, then press the SELECT
button.
-8-

Set Alarm
7:20 AM
9. According to different time necessary, you can select your favourite setting for
the alarm setting;
Once\Every day \Weekly \Weekdays /Weekends options are available;
10 And you can set the Alarm 'beeps' sound or internet radio station for the alarm
to
alert the customer when the Alarm expires;
Setting the “Sleep Timer
1. Press the BACK button.
2.ROTATE the TUNE until the display says <Alarm clock>
Alarm Clock
3. Press the SELECT button.
4. Turn the TUNE until the display says<Sleep Timer>.
Sleep Timer
5. Rotate the TUNE to change to sleep timer value and then press SELECT to
begin the sleep timer;
You will be able to select OFF or from 00:15 to 03:15 <one step for15 minutes >as
the
sleep timeout setting;
Note:
When you set that the radio will continue to play as normal, but it will go into
standby
mode after the sleep timer has expired. To turn the radio back on again,
simply
press the ON/OFF button.
-9-

GETTING STARTED WITH THE MEDIA PLAYER
In order to play the music files you have stored on your PC via the Media player
you
must ensure the following:
1. Your PC has the correct type of music files saved on it which are explained in
the following paragraphs.
2. The music files on your PC are not 'protected';
3. Te music files are stored in the correct location on your PC.
4. The PC has file sharing turned on.
5. The music files can be 'shared' on the network.
6. You know the name of your PC
MUSIC CONTENT
The internet radio plays the most popular music types,
FLIE TYPE FLIE EXTENSION SHOWN ON PC
MP3 .mp3
Windows Media .wma
Real .Ra
itunes .aac
Ogg Vorbis .ogg
(These are the letters that appear after the file name. e.g. MUSIC.mp3)
Instructions for streaming
1. Select Media Player on the radio. Switch on the internet radio and press
Back until you are at the top level menu. Turn the TUNE until Media Player is
displayed and press the SELECT button.
Media Player
2. You will be able to choose from 2 playback tracks;
Windows Shares
UPNP Servers
-10-

If you select ‘Windows Shares’ menu:
(1) Scan for PCs is displayed, press the SELECT button. Your computer network
will
scan and a list of all available PCs Will be displayed on you internet radio.
Note: If a PC does not have global file sharing turned on, or a third party firewall is
protecting
the PC it will not be visible when you scan for it.
(2)Turn the TUNE to highlight the PC you want to play music from and press the
SELECT button.
Note: you may be asked to enter a username and password to access the PC you
have
selected. This is the same user name and password you would enter if
actually
sitting in front of the machine.
(3)Finding folders
The internet radio will now scan the PC you have selected and display a list of any
folder
which have got 'sharing' enabled.
Note:
Your PC may have folder shared which do not contain the internet radio is just
searching for shared folders, so will find all shared folder, regardless of content.
Turn the TUNE to select the folder that contains the saved music, and press
the select button.
(4) Selecting music
You can now view the content of the shared folder by Album or Artist. Use the
TUNE to move through the list.
(5)Adding music to the queue and managing the queue. When you select music to
be
played, it is added to the play queue and played sequentially.
Set up your Windows PC to allow the radio to access your audio files via
Windows Shares
1. Please ensure that your PC is available on the network for you
Internet radio, then, using windows Explorer, locate the folder where
your audio files are stored.
2. Right Click on the folder.
-11-

3. Select ‘ Properties’.
4. Click on ‘Sha ring’.
5. Press the SELECT button, turn the knob until ‘Sc an for PCs’ is displayed
and
press SELECT again.
6. The radio will now display ‘Finding PCs ’. Once the radio has finished, turn the
knob to highlight the correct PC.
7. Press the SELECT button. The radio will search for shared folder.
8. Turn the knob to highlight the correct shared folder and press SELECT.
9. The radio will display ‘File Scan…’ as it scans through the media files in the
shared folder. Text on the bottom row of the display will change to
indicate that the file scan is in progress. If you have a large number of
audio
files this could take several minutes to complete.
10. Once the radio has finished scanning, it will display’ By Album’. You can
now
browse through the scanned media files, which will now be organized
‘ By Album’,’By Artist’- if available.
Note that the first time the file scan is done a file called ‘.reciva_media_cache’
is written to the folder where the audio files are stored. This is in order to
speed
up subsequent file scans.
Listening to a single shared track
1. Turn the knob until ‘ By Artist’ is displayed.
2. Press the SELECT button.
3. Turn the knob Until the required artist is displayed.
4. Press the SELECT button.
5. Turn the knob until the required album name is displayed.
6. Press the SELECT button.’ [Add to Queue]’ will be displayed.
7. Turn the knob until the required tack is displayed.
-12-

8. Press the SELECT button. The track will begin playing.
Listening to a complete shared album
1. Turn the knob until ‘B y Artist’ is displayed.
2. Press the SELECT button.
3. Turn the knob until the required artist is displayed.
4. Press the SELECT button.
5. Turn the knob until the required album name is displayed.
6. Press the SELECT button. ‘[Add to Queue] ‘ will be displayed.
7. Press the SELECT button. The album will begin playing.
Queuing up tracks for playback later
1. Highlight the required track.
2. Press the SELECT button. ‘Track Added To Queue’ will be displayed.
Queuing up albums for playback later.
1. Highlight the required album.
2. Press the SELECT Button.
3. Turn the knob until ‘[ Add To Queue]’ is displayed.
4. Press the SELECT button.’ Tracks Added to Queue’ will be displayed.
Controlling playback
1. Use the STOP button to stop playback.
2. Use the PLAY/PAUSE/STOP button to either pause a currently playing track
or
to restart a currently paused track or to restart a stopped track.
3. Use the PLAY/PAUSE/STOP button to stop a currently playing when you
-13-

press and hold the button for 2 seconds.
4. Use the PREVIOUS button to start playback of the previous track in the queue.
5. Use the NEXT button to start playback of the next track in the queue.
Browsing the list of tracks currently queued up for playback
1. Press the BROWSE button. The currently playing track name will be
displayed.
2. Turn the knob to see which tracks are queued up for playback.
3. If you want to jump to a particular place in the queue the SELECT button when
the
required track is displayed.
Playing tracks in random order
1. Select the individual tracks as described previously.
2. Navigate to top-level menu item ‘ Media Player’ using the SELECT and BACK
buttons.
3. Press the SELECT button.
4. Turn the knob until ‘P layback Mode’ is displayed.
5. Press the SELECT button.
6. Turn the knob until ‘S HUFFLE’ is displayed.
7. Press the SELECT button.
8. Turn the knob to select YES/NO the confirm that shuffle mode should be
enabled.
Playing tracks in the queue repeatedly
1. Select the individual tracks as described previously.
2. Navigate to top-level menu item ‘ Media Player’ using the SELECT and BACK
buttons.
-14-

3. Press the SELECT button.
4. Turn the knob until ‘P layback Mode’ is displayed.
5. Press the SELECT button.
6. Turn the knob until ‘Repeat’ is displayed.
7. Press the SELECT button.
8. Turn the knob to select YES/NO the confirm that shuffle mode should be
enabled.
If you select ‘UPnP Severs’ menu:
Locating and playing media files using the radio and UPnP
1. Once the UPnP server is configure to share media files with the internet radio,
you
can play the files by doing the following on the radio.
2. Keep pressing BACK to get to the radio’s top-level menu and then turn the
knob
to select ‘Media Player’.
3. Press SELECT and then turn the knob to highlight ‘UPn P Severs’.
4. Press SELECT and the radio will scan for all available UPnP servers. Note,
this may take a few seconds for the radio to complete its scan and before
the scan has completed, the radio will display ‘[Em pty]’. The radio will continue
to display ‘[Empty] if no UPnP servers are found.
5. After a successful scan , select your UPnP server, by rotating the knob if there
is more than on UPnP server, and then press SELECT.
6. The radio will now list the media categories available from the UPnP server,
e.g. ‘Mu sic’, ‘Play lists’ etc. Turn the knob to select which category you wish to browse,
press SELECT and turn the knob to highlight a sub category and
press SELECT again. For example, you could select ‘ Music’ and then ‘Album ’.
7. Turn the knob to highlight the media files that you wish to play and press
SELECT.
8. The radio will display ‘[A dd to Queue]’, press SELECT and the radio will add
the
tracks to its queue and begin playing them automatically.
Setup a Windows PC to allow the radio to access you audio files via a UPnP
serves
1. If your PC is running Microsoft Windows XP, then you can use Windows Media
Player 11(WMP11) to act as your UPnP( Universal Plug and Play) media
-15-