King gates Fred Myo 2 User manual

KING gates - Brand of Antoniolli Mario & C. s a s
Via A. Malignani, 42 - 33077 Sacile (PN) ITALY Tel. [phone] - Fax [phone]
e-mail: [email protected] web: www.king-gates.com
MADE IN ITALY
Fred Myo 2
INSTRUCTION MANUAL
EN
2-channel radio receiver.

1- PRODUCT DESCRIPTION
2- ELECTRIC CONNECTIONS
Fred Myo 2 is a radio receiver with 2 outputs, monostable (when it receives the command, the output
activates itself for 1 second).
1A - GENERAL DESCRIPTION
3- RADIO TRANSMITTER PROGRAMMING
Every operation (both radio transmitter
programming and channel configuration)
is done by the button.
The programming is signalled by the color of
the led, in particular:
-Green led: the operations concerning channel 1.
-Red led: the operations concerning channel 2.
3A - INTRODUCTION
Power supply 12-26 Vac/Vdc
Working temperature -20 ÷ +70
Reception frequency 433.920 MHz
No. storable codes 480 36mm
40mm
Relay contact Vac 1A 120V
Relay contact Vdc 1A 24Vdc
Absorption 60mA
1B - TECHNICAL FEATURES
Power +12/24Vac/dc
Ground
Programming
status signaling led
Programming
button
Normally open contact
channel 1 (NO)
Signal
Normally open contact
channel 2 (NO)
Socket
Within 5 seconds
make a transmission
pushing the desired
button on the transmitter
(the led switches off
and on again)
Within 5 seconds
make a transmission
pushing the desired
button on the transmit-
ter (the led switches
off and on again)
Wait 5 seconds, or
push the button on the
receiver.
The led switches off.
End programming.
Press one time the
button on the receiver.
The led switches on
green
Press two times the
button on the receiver.
The led turns
switches on
red
3B - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 1
Wait 5 seconds, or
push the button on the
receiver.
The led switches off.
End programming.
3C - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 2
Within 5 seconds
make a transmission
pressing the desired
button on the transmit-
ter (the led switches
off and on again)
Wait 5 seconds, or
push the button on the
receiver.
The led switches off.
End programming.
Press three times the
button on the receiver.
The led flashes
orange
3D - DELETING OF A RADIO TRANSMITTER
During the flashing,
keep the button on the
receiver pressed
until the orange led
becomes fixed on.
Release the button.
When the orange led
turns off, the memory
is erased.
Press three times the
button on the receiver.
The third time, keep
the button pushed.
The led flashes
orange
3E - DELETING OF ALL RADIO TRANSMITTER

1- PRODUCT DESCRIPTION
2- ELECTRIC CONNECTIONS
Fred Myo 2 is a radio receiver with 2 outputs, monostable (when it receives the command, the output
activates itself for 1 second).
1A - GENERAL DESCRIPTION
3- RADIO TRANSMITTER PROGRAMMING
Every operation (both radio transmitter
programming and channel configuration)
is done by the button.
The programming is signalled by the color of
the led, in particular:
-Green led: the operations concerning channel 1.
-Red led: the operations concerning channel 2.
3A - INTRODUCTION
Power supply 12-26 Vac/Vdc
Working temperature -20 ÷ +70
Reception frequency 433.920 MHz
No. storable codes 480 36mm
40mm
Relay contact Vac 1A 120V
Relay contact Vdc 1A 24Vdc
Absorption 60mA
1B - TECHNICAL FEATURES
Power +12/24Vac/dc
Ground
Programming
status signaling led
Programming
button
Normally open contact
channel 1 (NO)
Signal
Normally open contact
channel 2 (NO)
Socket
Within 5 seconds
make a transmission
pushing the desired
button on the transmitter
(the led switches off
and on again)
Within 5 seconds
make a transmission
pushing the desired
button on the transmit-
ter (the led switches
off and on again)
Wait 5 seconds, or
push the button on the
receiver.
The led switches off.
End programming.
Press one time the
button on the receiver.
The led switches on
green
Press two times the
button on the receiver.
The led turns
switches on
red
3B - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 1
Wait 5 seconds, or
push the button on the
receiver.
The led switches off.
End programming.
3C - PROGRAMMING OF A RADIO TRANSMITTER ON CHANNEL 2
Within 5 seconds
make a transmission
pressing the desired
button on the transmit-
ter (the led switches
off and on again)
Wait 5 seconds, or
push the button on the
receiver.
The led switches off.
End programming.
Press three times the
button on the receiver.
The led flashes
orange
3D - DELETING OF A RADIO TRANSMITTER
During the flashing,
keep the button on the
receiver pressed
until the orange led
becomes fixed on.
Release the button.
When the orange led
turns off, the memory
is erased.
Press three times the
button on the receiver.
The third time, keep
the button pushed.
The led flashes
orange
3E - DELETING OF ALL RADIO TRANSMITTER

KING gates - Brand of Antoniolli Mario & C. s a s
Via A. Malignani, 42 - 33077 Sacile (PN) ITALY Tel. [phone] - Fax [phone]
e-mail: [email protected] web: www.king-gates.com
MADE IN ITALY
Fred Myo 2
INSTRUCTION MANUAL
EN
2-channel radio receiver.