King Slide 1A88F Series User manual

1.10
www.kingslide.com
Undermount Slides
King Slide reserves the right to alter specications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
1A88F
• Length: 305 / 381 / 457 / 533mm
12" / 15" / 18" / 21"
• Travel: Full Extension
• Maximum Drawer Side Thickness: 16mm(5/8")
• Max. Load Capacity: 34 kg(75 lb)/pair
• Mount: Undermount
• Material: Galvanized Steel
• Packing: Unit Packed in 2 pairs/carton
6 pairs/carton
Push-Open with Silent Soft-Closing
Undermount Slide for Face Frame Cabinet
(16mm)
Profile Length
Cabinet Depth with Bracket
A
B
Drawer Length
bracket
37(1-7/16”)
9(11/32”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
Note
W
W - 42+0. 5
-1.0
Drawer Side Thickness
Maximum 16mm(5/8'')
min 6
37(1-7/16")
21(13/16")
min 27.5
max 13mm (1/2”)
13(1/2")
opening
Drawer Height
Max = opening - 24mm(1 5/1 6”)
Drawer Width
• Push-open, handle-free
• Enhanced silent soft-closing feature with light opening force
• Durable damping system with fast response capability
• All mechanical device, instead of electric-driven
• Safe, ergonomic and energy saving
• Undermount with full extension travel length
• Ultra smooth gliding motion with high rigidity and stability design
• 2 dimensional trimming system provides tool-less height and
depth adjustments
• A tool-less adjustment system is available to permit minor
installation inaccuracies, thereby reducing assemblage complexity.
• Effortless assembly and removal of drawer with front release lever
• High installation allowances for drawer width: +0.5/-1mm, and for
drawer depth: +1/-1mm
Specifications
Features
Applications
• For Face Frame Cabinet : Kitchen Furniture, Kitchen Cabinetry,
Home Cabinetry and Box Drawers

1.11
www.kingslide.com
Undermount Slides
King Slide reserves the right to alter specications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
Undermount Slides
1
Dimension Specifications
Profile Length
Cabinet Depth with Bracket
A
B
Drawer Length
bracket
37(1-7/16”)
9(11/32”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
Note
W
W - 42+0.5
-1.0
Drawer Side Thickness
Maximum 16mm(5/8'')
min 6
37(1-7/16")
21(13/16")
min 27.5
max 13mm (1/2”)
13(1/2")
opening
Drawer Height
Max = opening - 24mm(15/16”)
Drawer Width
Profile Length
Cabinet Depth with Bracket
A
B
Drawer Length
bracket
37(1-7/16”)
9(11/32”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
Note
W
W - 42+0.5
-1.0
Drawer Side Thickness
Maximum 16mm(5/8'')
min 6
37(1-7/16")
21(13/16")
min 27.5
max 13mm (1/2”)
13(1/2")
opening
Drawer Height
Max = opening - 24mm(15/16”)
Drawer Width
Item No. Drawer Length
mm (inch)
Overall Cabinet Depth
mm (inch)
Cabinet Depth With Bracket
mm (inch) Profile Length
mm (inch)
System Screw Locations
mm (inch)
MAX MIN A B
1A88F305 305 (12") 381 (15") 369 (14-9/16") 326 (12-7/8") 318 (12-1/2") 165 (6-1/2") 261 (10-1/4")
1A88F381 381 (15") 457 (18") 446 (17-9/16") 403 (15-7/8") 394 (15-1/2") 165 (6-1/2") 357 (14-1/16")
1A88F457 457 (18") 533 (21") 522 (20-9/16") 479 (18-7/8") 470 (18-1/2") 261 (10-1/4") 453 (17-13/16")
1A88F533 533 (21") 610 (24") 598 (23-9/16") 555 (21-7/8") 546 (21-1/2") 261 (10-1/4") 517 (20-3/8")
Fit with American standard 3" cabinet depth system.
Drawer Removal:
Simply press the front release device to
remove the drawer
250
300
350
400
450
500
550
32
18
32 32
9
3796
192
288
4(max)
18
W-42
W
+0.5
-1.0
min 6
max 16
37
21
min 27.5
max 13
W : Internal Cabinet Width
Tool-less Height Adjustment :
Simply rotate the wheel at the front bottom of the drawer to
adjust the drawer height
Space Requirement
Drawer Width Formula
Drawer Side Thickness
mm (inch)
"W" minus
mm (inch)
16 (5/8") 10 (3/8")
15 (19/32") 12 (15/32")
14 (9/16") 14 (9/16")
13 (1/2") 16 (5/8")
12 (15/32") 18 (23/32")
W: Internal Cabinet Width
Example:
Internal Cabinet Width = 457 mm (18")
Drawer Side Thickness = 13 mm (1/2")
Drawer width = 457 - 16 = 441 mm
= (18") - (5/8") = 17-3/8"
+0.5
-1.0
Note:
Ensure the slide is parallel to the horizon or tilt to cabinet front on both sides during
installation.
○
Chipboard Screws System Screws
X
Round Head Screw
Easy Assembly with Front-End Installation
Our specially designed front-end installation allows quick and
simple drawer installation and removal processes. The quick
connect and disconnect device is located at the front-end
under the drawer, keeping intact the elegant appearance of the
drawer.
Note: Holes other than those shown may be in the slide member at King Slide's option
and may change without notice.

1.14
Undermount Slides
King Slide reserves the right to alter specications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
X
Z(setback) = (X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide bottom can not be lower than opening
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-5/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length
Installation Instruction
1. Before installing the slides, make sure the dimensions of the cabinet and drawer meet the requirements specified in Fig. 1 and ' Space Requirement'
drawing resectively for the slide to be installed.
2. Drill holes on the cabinet following the 'Installating Specification' drawing on the reverse page. Mount the slides and the rear brackets on the cabinet
using the recommended type of screws.
3. Make cut-outs on the drawer according to Fig. 2A 's dimension (Using the drill template FL00ZD0-A as page 1.39 is recommended) , then install
the front release lever according to Fig. 2B and 2C.
4. Pull out the slides on the cabinet.
1A88F & 1B88F
Installation Requirement
Rear Bracket
Front View
Dimension Specification
X
Z(setback)=(X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide bottom can not be lower tha n open ing
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-13/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length
Fig. 1
Fig. 2A
Fig. 2C
Fig. 2B
Inset Install Formula
x 16 17 18 19 20 21 22
Y 57 58 59 60 61 62 63
Z 24 25 26 27 28 29 30
L: Slide Length X: Front Panel Thickness
Note:
Ensure the slide is parallel to the horizon
or tilt to cabinet front on both sides during
installation.
You can use optional drill template
FL-00ZD0-A as page 1.39
X
Z(setback) = (X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide bottom can not be lower than opening
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2. 0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-13/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length

1.15
www.kingslide.com
King Slide reserves the right to alter specications of all the products without notice. If the entity is different from the illustration, please refer to the entity.
Undermount Slides
1
5. Position and align the drawer with the slide as shown in Fig. 3A and 3B. Push the drawer all the way into the cabinet as shown in Fig. 3C until
clicked to complete the installation.
6. After confirming the drawer is operating normally, install the front panel.
7. If height / depth adjustment is needed after installation, please refer to the Detail Adjustment Info. below or the feature diagram on the previous
page.
X
Z(setback)=(X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide bottom can not be lower than opening
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-13/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length
Detail Adjustment Info
X
Z(setback)=(X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide b ott om ca n not be lowe r tha n opening
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2. 0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-13/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length
Fig. 3A
Fig. 3B
Fig. 3C
X
Z(setback)=(X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide bottom can not be lower than opening
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-13/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length
X
Z(setback)=(X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide bottom can not be lower than opening
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-13/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length
X
Z(setback)=(X +**4) +4(max)
Min = L+ Z+ 5(3/16")
Max = L+ Z+ 48(1-15/16")
Blocking Behind Frame
Y
bracket
◎Slide bo ttom can not be l ower than ope ning
Cabinet Depth
Drawer Length
Bracket
37(1-7/16”)
4(5/32")max
**4
min gap
(push-open)
10
(3/8”)
X
+2.0
-0
0
Normal lnstall
Inset lnstall
Note
Note
Inward
Outward
4.0
+2.0
Factory setting
*
Inward
1.0mm
*Closing System Adjustments
Inward
1.0mm
*
*
Outward
Inward
The adjustments here can fine-tune the slide function.
If the issues still exist after the adjustments, please
reset to default settings and ensure each installation
dimension is in accordance with the specification.
rear notch
33(1-13/16″)
7(9/32″)
11(7/16″)
Ø6*10
XO
Locking Device
Locking Device with Extension Plastic
Extension Plastic
*Minimum 3 screws per bracket
21
(13/16")
(15/32")(9/16") 1214
32(1-1/4'')
16(5/8'')
2(3/32'')
Front Gap Adjustment
Profile Length
To prevent installation errors which may lead to the
drawer getting stuck, Please make sure the nomal
operation of the drawer before securing the front
panel.
Notes for installation
1. Ensure the drawer body appearance is upright. It could not be diamond trapezoidal or distorted!
2. Ensure the side space, depth on both sides are consistent.
3. Ensure the installation location or the cabinet is on a flat surface.
4. Ensure the front release lever is installed correctly.
5. Ensure the drawer dimensions, rear notch locking hole, internal drawer width, and the drawer bottom recess are correct.
Notice