Kings Adventure AKRR-TUBRACK 01 User manual

USER MANUAL
SKU: AKRR-TUBRACK_01
UNIVERSAL UTE TUB RACK

2V1.4
CONTENTS
PLEASE READ AND UNDERSTAND THIS MANUAL
COMPLETELY BEFORE USING THIS PRODUCT.
1. WARNING 3
2. GENERAL INFORMATION 3
2.1 Package Contents 3
3. INSTALLATION 4
3.1 Tub Rack Installation 4
3.2 Adding a Roof Top Tent 6
4. WARRANTY 7

3V1.2
1. WARNING
The Adventure Kings Ute Tub Rack is rated to a dynamic load rating of 100kg, we recommend users check
the load rating capacity of their tubs with their vehicle manufacturer before use.
Added weight can alter the braking and driving behavior of your vehicle. Adhere to payload limits of your
vehicle and do not overload.
The Adventure Kings Ute Tub Rack is height adjustable, be mindful of any changes to the overall height of your
vehicle.
Fitting Time: 2 Hours
Required Tools: 13mm, 17mm Spanner, Allen Key, Tape Measure, Drill, 3mm and 10mm Drill Bit
Recommended Tools: Deburring Tool (or something to clean up holes), touch up paint, tape, marker pen.
2. GENERAL INFORMATION
2.1 PACKAGE CONTENTS
QTY ITEM
4 Lower Legs
4 Upper Legs
1 Headboard
1 Tailgate
6 Support Beams
88 M8 Nylock Nuts
88 M8 x 20 Bolt
8 M10 x 50 Bolt
4 M10 x 30 Bolt
88 M8 Flat Washer
12 M10 Flat Washer
88 M8 Spring Washer
12 M10 Spring Washer
12 M10 Nylock Nuts

4V1.4
Assemble the four legs by bolting one upper and one lower leg piece together. Position the
lower leg piece and the upper leg piece in a way that aligns the holes at the desired height.
Place a M8 flat washer on to one M8x20 bolt and feed thread through the aligned holes.
Place an M8 Spring washer and M8 Nylock nut and finger tighten.
Complete this step for all 4 legs.
(It’s recommended to use a minimum of 6x bolts per leg – preferably 9x bolts.)
3. INSTALLATION
It’s easiest to assemble the basic structure on the ground. This tub rack’s height is adjustable and can be
altered once its on the vehicle. Installation can be easier done at a lower height and later altered to suit your
requirements.
STEP
1
STEP
2With a tape measure, measure the width of the upper edges of your tub to give you an idea of
which holes to use on the headboard and tailgate pieces.
3.1 TUB RACK INSTALLATION

5V1.2
STEP
3
STEP
4
STEP
5
STEP
6
STEP
7
With your mate, remove the tub rack from your tub. Using the 3mm drill bit, drill pilot holes in
the previously marked positions. Widen the holes with a 10mm drill bit.
Grab a mate and position the rack where you want to mount it, make sure it is square
compared to the cabin. Using masking tape and a marker pen is a good way to mark your
mounting points on the tub. Use a marker, mark the centre of the holes on the lower legs –
these are the drill points for your tub. Repeat for each leg.
Add two support pieces to the top of the tub rack, connecting the two ends. Fit M8x20 bolts
washers and nuts and finger tighten. Now the rack will free stand and is assembled enough
to mount to the tub.
Slot the headboard piece and tailgate piece into the upper legs, adjust the width to suit your
vehicle. Add M8 bolts with washers and finger tighten with M8 Nylock nut.
STEP
8
STEP
9
NOTE 1. ENSURE ALL SUPPORT PIECES ARE USED
NOTE 2: PERIODICALLY CHECK AND RETIGHTEN BOLTS AS REQUIRED
With the feet tightened, you can adjust the overall height and fine tune the width.
Once paint has dried, the tub rack can be mounted again. Once mounted fit 8x M10 x 50
bolts to the vertical holes drilled and 4x M10 x 30 bolts to the horizontal holes drilled into the
tub. All bolts’ nuts and washers should be tightened on each leg to the tub rack. Remember
to use flat washer to spread the load of the bolt.
Using a deburring tool, you can clean up any of the holes you have drilled, as well as touching
up the paint to cover the fresh drilled metal to prevent rust.

6V1.4
3.2 ADDING A ROOF TOP TENT
If you are adding a Kings Rooftop Tent, we advise that the “front to back” support beams are aligned with the
mounting extrusion of the base of the tent (825mm apart). This provides a solid mounting base and an even
distribution of weight.
We recommend periodically checking all nuts and bolts.
Due to the size and mounting rail positioning, tents such as the the “Kwiky” should be used in conjunction with
a suitably sized flat rack or platform.

7V1.2
4. WARRANTY
WARRANTY PERIOD:
Full 12 month warranty from date of purchase against all manufacturing defects.
WHAT DOES THE WARRANTY COVER?
Under normal usage conditions, this warranty covers:
a. Any defect in design or manufacture which results in the product failing to perform substantially as described
in authorised advertising or literature.
b. We will either repair or replace the product at our discretion providing that the fault is found to have been
caused by a design or manufacturing defect and not misuse or tampering.
Our goods come with guarantees that cannot be excludedunder the Australian ConsumerLaw. You are
entitled to a replacement or refund for a major failure and for compensation for any other reasonably
foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be
of acceptable quality and the failure does not amount to a majorfailure. The benetsprovided to you as the
consumer by this warranty are in addition to other rights and remedies available to you under the law.
THE WARRANTY DOES NOT COVER:
a. Any damage resulting from improper use
b.
c. The cost of removing and reinstalling the product
d. Travel and /or other expenses due to customer’s remote location
e. Transport charges and damage in transit. It is your responsibility to deliver and pick up your product,
including any costs associated with the postage of your repair or replacement product. If you do freight your
product we recommend that you insure against loss or damage.
f. Any loss directly or indirectly associated with the product failing to operate.
g. Damage caused by mould, insects, animals, misuse, incorrect operation, adverse weather, accidents
and fair wear and tear
TO MAKE A CLAIM, PLEASE ENSURE YOU RETAIN YOUR SALES RECEIPT OF PURCHASE
1800 88 39 64
12 MONTH LIMITED
WARRANTY
OUTDOOR SUPACENTRE PTY LTD
Level 1, Building A, 6 Figtree Drive,
Sydney Olympic Park, NSW 2127, Australia
PHONE: [phone]
www.4wdsupacentre.com.au
Faulty installation or modication made during installation