KIP 600 Series User manual

User Manual
Version A.2a June 26, 2019

(1)
Thank you for purchasing the KIP 600 Series.
This Hardware Operation Guide contains functional and operational explanations for the KIP 600
Series.
Please read this Hardware Operation Guide carefully before using the Printer.
Please keep this Hardware Operation Guide for future reference.
1. When this product is installed in North America.
This product complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This product may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the product.
Note: This product has been tested and found to comply with the limits for a Class A digital
equipment, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the product is operated in a
commercial environment. This product generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this product in a residential area is
likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This product complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS
standard(s). Operation is subject to the following two conditions: (1) this product may not cause
interference, and (2) this product must accept any interference, including interference that may
cause undesired operation of this product.
Le présent appareil est conforme aux la partie 15 des règles de la FCC et CNR d’Industrie
Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux
deux conditions suivantes : (1) I’appareil ne doit pas produire de brouillage, et (2) I’utilisateur
de I’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est
susceptible d’en comprometter le fonctionnement.
Contains FCC ID: VP8-13551 Contains IC: 7391A-13551
2. When this product is installed in Europe
This product complies with the requirements in CISPR 32 for a Class A computing equipment.
Operation of this product in a residential area may cause unacceptable interference to radio
and TV reception requiring the operator to take whatever steps are necessary to correct the
interference.
Do not install product around other electronic equipment or other precision instruments.
Other equipment may be effected by electrical noise during operation.
If the product is installed near other electronic equipment, such as a TV or a radio,
interference to said equipment, such as noise or flickering, may occur.
Use a separate power line and install the PRINTER as far as possible from said equipment.

(2)
The International ENERGY STAR ® Office Equipment Program is an international program that
promotes energy saving through the penetration of energy efficient computers and other office
equipment. The program backs the development and dissemination of products with functions that
effectively reduce energy consumption. It is an open system in which business proprietors can
participate voluntarily. The targeted products are office equipment such as computers, monitors,
printers, facsimiles, copiers, scanners, and multifunction devices. Their standards and logos are
uniform among participating nations.
Das Gerät ist nicht für die Benutzung am Bildschirmarbeitsplatz gemäß BildscharbV vorgesehen.
KIP 600 Series is an ENERGY STAR qualified multifunction device.
The symbol shown indicates that this product conforms to
SJ/T11364-2006 of People’s Republic of China Electronic
Industry Standard and does not apply to countries outside of
People’s Republic of China.
The symbol shown indicates that this product conforms to GB
18455-2001, SJ/T 11364-2006 of National Standard of the
People’s Republic of China and does not apply to countries
outside of People’s Republic of China.
The symbol shown indicates that this product conforms to Directive
2012/19/EC of the European Parliament and the council of 4 July 2012
on waste electrical and electronic equipment (WEEE) and does not
apply to countries outside of EU.

(3)
The following warnings are very important in order to safely use this product.
These notes are important in preventing danger to the operator or operation of the printer.
The following symbols are found throughout the USER’S Manual and have the following meaning:
CAUTION
This CAUTION mark means that there is a possibility of injury or physical
damage if you ignore or do not follow the said instruction.
When marked with this symbol, “DO NOT ATTEMPT”.
When marked with this symbol, “pay close attention to”.
Safety Warning
WARNING
This WARNING mark means that there is a possibility of death or serious
injury if you ignore or do not follow the said instruction.
There are extremely hot parts inside.
Do not touch any parts, or you will be burnt.

(4)
WARNING
1. The Power source should be as follows:
208V to 240V plus 6% or minus 10%, 50/60Hz, 16A or higher
2. Use a circuit with a dedicated breaker.
3. Install the product as close to the wall outlet as possible.
4. If you wish to move the printer, please contact your service personnel.
Ground the product with a correct ground source or you may be electrically
shocked.
1. Do not plug in the printer into a multi-wire connector in which some other
equipment is plugged into.
It may cause a fire due to outlet overheating.
2. Do not damage the Power Cord by stepping on or placing heavy items
on it.
If the Power Cord is damaged, it may cause a fire or you may receive
an electric shock. REPLACE THE CORD IF DAMAGED!
1. Do not put a flower vase, a flowerpot or any water-filled item on the
product.
Spilt water could cause a fire or an electric shock.
2. If the product generates an abnormal smell or noise, turn it off and
unplug it from the wall electrical outlet immediately.
1. Do not remove the screw and do not open the cover if not instructed to
do so in this User’s Manual. If you ignore this warning, you may be burnt
or receive an electric shock due to a hot item or electrically charged part
inside of the printer.
2. Do not disassemble or tamper with the printer.
It may result in a fire or an electrical shock.
Do not throw the toner into a fire or other sources of heat, as it can
explode.

(5)
CAUTION
There are hot items inside of the printer.
Take great care not to touch these items when you remove mis-fed media.
Do not pull the cord when you unplug the printer as you may damage the
Power Cord.
Do not install the printer in a humidified room or a dusty room.
Also, do not install the printer on an unstable floor as injuries may occur.
1. Unplug the printer before you move it.
The power cord may be damaged and it may result in a fire or electric
shock.
2. If you do not use the printer for a long duration (holidays, company
shutdown) turn off and unplug the printer from the outlet for safety.
Ventilate the room well if you print in a small area.

(6)
POWER CORD INSTRUCTION
The installation of (or exchange to) a power plug which fits in the wall outlet of the installation
location shall be conducted in accordance with the following:
WARNING
Select a power plug which meets the following criteria;
- The plug has a voltage and current rating appropriate for the product’s rating marked on
its name plate.
- The plug meets regulatory requirements for the area.
- The plug is provided with a grounding pin or terminal.
If the appropriate plug does not fit the wall outlet in the installation, the customer shall install an
appropriate outlet.
Connector Type:
Configuration Standard Rating Usually found in
IEC60320:C19 20A 250V (UL)
16A 250V (IEC)
Plug Type: Model Rating 208V-240V
Configuration Standard Rating Usually found in
NEMA6-20 20A 250V North America
(UL Listed)
CEE7/7 16A 250V European countries
KS C 8305 16A 250V Korea
AS/NZS 3112 16A 250V Australia
New Zealand
GB1002
GB2099.1 16A 250V China
IRAM 2073 16A 250V Argentina
Cord Type
Standard Rating Usually found in
SJT 3X12AWG Long <4.5m 20A 250V North America
(UL Listed)
HO5VV-F 3X1.5mm216A 250V European countries
Argentina
RVV 3X1.5mm216A 250V China

Chapter 1 Before Use1-1
Chapter 1
Introduction
Page
1. 1 Installation Requirements 1-2
1. 2 Originals Prohibited from Duplication 1-3
1. 3 Features 1-4
1. 4 Specifications 1-5
1. 4. 1 Printer 1- 5
1. 4. 2 Scanner (for KIP 660) 1- 7
1. 5 Appearance 1-8
1. 5. 1 Front view 1- 8
1. 5. 2 Left side view 1- 9
1. 5. 3 Right side view 1- 10
1. 5. 4 Rear view 1- 11
1. 6 Specifications for Print Media 1-12
1. 6. 1 Papers not to be used 1- 12
1. 6. 2 Paper Storage 1- 13
1. 6. 3 Environmental Considerations 1- 14
1. 7 Specifications for Originals 1-15
1. 7. 1 Original Standards 1- 15
1. 7. 2 Special Documents 1- 15
1. 7. 3 “Do Not Scan” Originals 1- 16

Chapter 1 Before Use
1-2
1. 1Installation Requirements
The following conditions are required for installation of the equipment.
1. Power source should be rated as:
208V - 240V plus 6% or minus 10%, 50/60Hz, 16A or higher
2. The equipment must be on an exclusive circuit.
3. The outlet must be near the equipment and easily accessible.
1. Make sure to connect this equipment to a grounded outlet.
2. For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near
the equipment and shall be easily accessible.
1. The installation site must not have open flames, dust or ammonia gases.
2. Not to be installed near solvent based printers, corrosive gases or devices that emit
them.
3. The equipment must not be exposed to the air vents from air conditioners.
It may affect the image quality.
4. The equipment should not be exposed to the direct sunlight.
Please draw curtains to block any sunlight.
When you open the Upper Unit to remove a mis-feed, do not expose the
Photoconductive Drum to strong (intense) light as this will damage the Drum.
Ventilate the room, if required.
The site temperature range = 10 to 30 degrees Centigrade, with the humidity between
15% to 80% RH. (NON-CONDENSING)
Keep the printer away from water sources, boilers, humidifiers, refrigerators, kerosene
(oil) stoves or other printers which emit gases.
Keep ample room around the equipment to ensure comfortable operation.
(Refer to the following figure.)
The equipment must be leveled and the floor strength must be ample to sustain the
weight of the equipment.
C
Rear
Front
Left
Right
600mm
600mm
600 mm
1500mm
1035 mm
1500mm
2700 mm
3135 mm

Chapter 1 Before Use1-3
1. 2 Originals Prohibited from Duplication
It may be illegal to duplicate or copy certain types of originals and you may be punished by local or
regional laws, if copies are made of these types of documents.
Please be aware of your local or regional laws and which originals they forbid you to duplicate.
Some Examples:
[Originals prohibited from copying by law(s)]
1. Do not copy Currency (Bill, Money, Bank Note, etc.), Government issued Negotiable
Instruments (National Bonds, Security, Local Debt Bonds, etc.).
2. Do not copy Foreign Currency or Foreign Negotiable Instruments.
3. Do not copy unused postal stamps or government postcards without permission to
make replica from said Governments.
4. Do not copy Government issued revenue stamps, certificate stamps that are
prescribed by Liquor Tax Act or the Commodity Tax Act.
[Special items which require your attention]
1. The government issues warnings if you are to copy private issued securities (stock certificate,
draft, check, goods ticket, etc.), commutation ticket or book of tickets, excluding that some
specific company copies such originals as many as it requires for its own business.
2. We recommend you not copy originals as government issued passports, public or
private issued licenses, automobile inspection certification, ID and tickets passes or meals.
[Originals protected by the copyright]
It is prohibited to copy originals such as books, music, paintings, printed copies, maps, drawings,
movie posters and pictures which are protected by the copyright laws. Please refer to your local
or regional laws.

Chapter 1 Before Use1-4
1. 3 Features
(1) Electro Photographic, full color LED printer/MFP using KIP Contact Control Technology with
KIP Contact Array Charging and KIP Image Smoothing Technologies.
(2) Models:
- KIP 650 : 2 roll wide format color and monochrome printer
- KIP 660 : 2 roll wide format color and monochrome MFP
(3) Supported widths and lengths:
Maximum width : 914mm (36”)
Minimum width : 279.4mm (11”)
Maximum length : 6,000mm (for A0/36”)
Minimum length : 210mm (8.5”)
(4) KIP 600 Series prints at
- 6.0 D size (Eng) or
- 5.7 A1 size
prints per minute (60mm/sec) in color / monochrome, regardless of image type.
(5) Transfer Belt Technology permits accurate color registration.
(6) Prints are ready for immediate use with high durability to include UV and water resistant.
(7) 12" multi-touch panel allows for tablet-like operation and image viewing.
(8) Easy access to the USB port permits quick prints using easy touch panel functions.
(9) Feature rich, KIP System K Software applications and drivers.

Chapter 1 Before Use1-5
1. 4 Specifications
1. 4. 1 Printer
Subject Specification
Model KIP 600 Series
- KIP 650 : 2 rolls wide format color printer
- KIP 660 : 2 rolls wide format color MFP
Type Console, full color and monochrome print/scan
Printing method LED Array Electro Photography, Dry Toner
Color CMYK
Photoconductor Organic Photoconductive Drum
Print Productivity 60mm/sec. (6.0 D/min, 3.1 E/min.) : Color and monochrome
(5.7 A1/min, 2.9 A0/min.) : Color and monochrome
Exposure method Multi-Level (9 levels) LED Print Head
Resolution 600dpi x 2400dpi
Print width Maximum : 914mm (36 inches)
Minimum : 279.4mm (11 inches)
Print length Maximum :
Minimum : 210mm (8.5 inches)
NOTE : If the print is longer than the above, KIP does not
guarantee image quality or the reliability of the media feeding
system.
Plain Paper / Bond 5x standard portrait 6000mm in case of A0/36"
Tracing Paper / Vellum 1x standard portrait
Film 1x standard portrait
Glossy Paper 1x standard portrait
Warm up time Less than 5 minutes
(At 23 degrees centigrade, 60% RH and 208V)
Fusing method Heat roller fusing
Development Contact, mono component non-magnetic development system
Drum charging Charging Roller (KIP CAC Technology)
Transfer Transfer roller
Separation Electrostatic separation (AC)
Media feeding method Automatic - 2 rolls
Rating power 208 to 240V (+6% to -10%), 14A and 50/60Hz
Interface Ethernet 10BASE-T, 100 BASE –TX, 1000 BASE-T
USB 2.0/3.0 (5VDC max)
Power consumption 230V, 50/60Hz
Printing 1.4 kW (Average)
Warm up 3.3 kW (Average)
Ready 0.5 kW (Average)
Cold Sleep 3.2 W (Average)
Acoustic noise Less than 65dB (Printing)
NOTE : Impact noise such as cutting sound is excluded.
Less than 60dB (Ready)
The highest sound pressure according to EN ISO 7779 is 70dB (A) or less.

Chapter 1 Before Use1-6
Subject Specification
Dimensions KIP 650 : 1500mm (W) x 1035mm (D) x 900mm (H)
KIP 660 : 1500mm (W) x 1035mm (D) x 1050mm (H)
NOTE: Touch panel and upper trays are not included.
Weight KIP 650 ~369 kg
KIP 660 ~392 kg
Media
(Recommended) Bond/Plain paper - 67g/m2to 120g/m2
Tracing paper
- 75g/m2
Gloss
- 120g/m2
NOTE: Refer to regional media guide(s)
Environmental
condition Standard Environment : 23oC and 60% Temperature 10 to 30 degrees centigrade
Humidity 15 to 80% RH
Storage of
consumables Print media Wrap the media to prevent access of moisture Toner Keep the bottles away from direct sunlight, and store
between 0 - 35 oC and 10 - 85% RH.
NOTE
Specifications may be changed without notice.

Chapter 1 Before Use1-7
1. 4. 2 Scanner (for KIP 660)
Subject Specification
Scanning method Contact Image Sensor (CIS)
(5 pieces of A4 sized CIS)
Light source LED (R/G/B)
Scanning speed
(600 dpi, normal quality)
(max)
Monochrome : 65mm/s
Grayscale : 65mm/s
Color : 22mm/s
NOTE: Actual speed may vary by the scan software.
Setting of original Face up
Starting point of scan Center
Scan width Max: 914.4mm / 36”
Min : 210mm
Scan length Max: 6,000mm / 19.7ft (Including the margin area)
Min : 210mm / 8.5” (Including the margin area)
NOTE :
If the original is longer than 6,000mm, image quality or the feeding reliability is not
guaranteed.
Optical resolution 600dpi
Digital resolution 200 / 300 / 400 / 600 dpi
Original transportation Sheet through type
Transportable original
thickness Max: 1.60mm Min : 0.05mm
NOTE :
Suggest to change “It does not guarantee both scan/copy image quality and original feeding
reliability in case the original is non-standard size one of which thickness is 0.25mm or thicker.
NOTE
Specifications may be changed without notice.

Chapter 1 Before Use1-8
1. 5 Appearance
1. 5. 1 Front view
Name of part Function
1 Print Tray These trays catch ejected prints.
2 Scanner Unit Read the original with this unit when you make scan or copy.
(KIP 660 only)
3 Scan Abort Button While scanning: emergency stop
At Standby position: eject
(KIP 660 only)
4 Start Button Starts scanning if the controlling software requires user
intervention.
5 User Interface This is a Touch Screen, and many kinds of user operation are
available.
PLEASE DO NOT push the LCD area too strong.
6 Roll Deck Roll media can be loaded here.
7 Status Indicator LED indicator indicates the following printer status.
Colo
r
Condition Status
Green Light Ready, Printing
Green Blink Warming up.
Orange Light Operator Call Error
Red Light Service Call Error
Blue Light Warm sleep
Blue Light Cold sleep
light purple Light When printer is power-off and print
controller is still power on.
5
1
1 3
4
2
7
6

Chapter 1 Before Use1-9
1. 5. 2 Left side view
Name of part Function
1 Toner Supply Port Toner Cartridge (C, M, Y, K) to be set here to add toner to the
system.
2 Left Side Door Access Waste Container, Purge Switch and Feeder Release Knob.
3 Waste Toner Box Collects the wasted toner.
4 Purge Switch After removing jammed sheets, press this switch to eject remaining
sheet from the printer.
5 Feeder Release
Knob Unlocks the Feeder Unit to clear misfeeds.
1
32
5
4

Chapter 1 Before Use1-10
1. 5. 3 Right side view
Name of part Function
1 USB Port Your USB flash memory can be used here. (5VDC max.)
2 Power Switch Turn on/off the Printer.
1
2

Chapter 1 Before Use1-11
1. 5. 4 Rear view
Name of part Function
1 Fuser Cover Prints come from the opening on this.
Open the Fuser Cover when you remove the misfeeds inside the
Fuser Unit.
2 Breaker It is possible to shut off supplying the AC power.
3 Inlet Socket Connect the Power Cord here.
1
2
3

Chapter 1 Before Use1-12
1. 6 Specifications for Print Media
1. 6. 1 Papers not to be used
Do not use the following kinds of printing paper. Doing so may damage the print engine.
Excessively curled
(a diameter of 50 mm or
less)
Folded
Creased
Torn
Punched

Chapter 1 Before Use1-13
Pre-printed
Extremely slippery
Extremely sticky
Extremely thin and soft
OHP Film
1. 6. 2 Paper Storage
Keep the paper in the custody taking care of the following matters.
1. Do not expose the paper to the direct sunlight.
2. Keep the paper away from high humidity. (It must be less than 70%)
3. Put the paper on a flat place
4. If you will keep the paper in the custody, which you have already unpacked, put it into the
polyethylene bag to avoid the humidity.
CAUTION
Do not use the paper with staple, or do not use such conductive paper as aluminium foil and
carbon paper.
The above may result in a danger of fire
NOTE
(1) Print image may become light if printed on a rough surface of the paper.
(2) Print image may become defective if the print paper has an excess curl.
(3) It will become a cause for paper mis-feed, defective print image or paper creasing if you
use a paper that does not satisfy the specification.
(4) Do not use a paper of which surface is very special, such as thermal paper, art paper,
aluminium foil, carbon paper and conductive paper.
(5) Do not use papers with unpacked (exposed in high / low temperature & humidity) in a
long period. Such papers may result in mis-feed, defective image or paper creasing.
(6) Tracing paper exposed to air over a long period tends to cause a defective printing.
Removing one round on the surface of the tracing roll paper from the beginning is
recommended.
Refer to [2.3 Replacing Roll Media].