manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Kirby Morgan
  6. •
  7. Diving Instrument
  8. •
  9. Kirby Morgan 37 & 57 User manual

Kirby Morgan 37 & 57 User manual

WARNING
Diving with compressed breathing gas is a hazardous activity. Even if you do everything
right there is always the danger that you may be killed or injured. No piece of diving
equipment can prevent the possibility that you may be killed or injured any time you
enter the water.
Kirby Morgan®37 & 57 Helmets
Operations and Maintenance Manual
KMDSI Part # 100-073
Kirby Morgan Dive Systems, Inc.
1430 Jason Way
Santa Maria, CA 93455, USA
Telephone (805) 928-7772, FAX (805) 928-0342
E-Mail: [email protected], Web Site: www.KirbyMorgan.com
Manual prepared by KMDSI, Dive Lab, Inc. and Marine Marketing and Consulting.
NOTE: This manual is the most current for the Kirby Morgan 37 and 57 Helmet. It is page dated January 2014. Fu-
ture changes will be shown on page IV and the changed pages will carry the date of change. Previous manuals may
not reect these updates.
™
Document Number 130108002
Kirby Morgan, SuperLite®, BandMask, Band Mask, KMB, KMB-Band Mask, DSI, Diving Systems International, EXO, REX®,
SuperFlow®and DECA are all registered trademarks of Kirby Morgan Dive Systems, Inc. Use of these terms to describe products
that are not manufactured by KMDSI is illegal.
The two dimensional images (such as photographs and illustrations) of our products are © copyrighted and trademarks of Kirby
Morgan Dive Systems, Inc. The three dimensional forms of our products are trademark, trade design and trade dress protected.
© ⅯⅯⅩⅢ Kirby Morgan Dive Systems, Inc. All rights reserved. This manual is made available for the express use of the owner of
this Kirby Morgan product. No part of this manual may be reproduced, stored in any retrieval system, or transmitted, or used in any
form or by any means, whether graphic, electronic, mechanical, photocopy, or otherwise by technology known or unknown, without
the prior written permission of Kirby Morgan Dive Systems, Inc.
The Kirby Morgan 37 helmet is CE Approved and meets or exceeds all performance and testing require-
ments of all government and non-government testing agencies throughout the world. It is approved for
use on all commercial and military work underwater.
The KM37 helmet is covered by U.S. Patent #6,644, 307B2. Foreign and other patents pending.
II © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
Warranty Information
KMDSI warrants every new Mask, Helmet, Scuba Regulator, Manifold Block or Kirby Morgan Air Control
System 5 (KMACS 5) (each, a Product) to be free from defects in workmanship for a period of three hun-
dred sixty ve (365) days from the date of purchase from a KMDSI authorized dealer. This warranty covers
all metal and plastic parts, but does NOT cover rubber parts, communications components, or head and chin
cushions. In addition, due to the electrolytic nature of underwater cutting and welding, chrome plating can-
not be warranted when the diver engages in these activities.
Any defect of the product in workmanship or material covered by this warranty discovered within three
hundred sixty ve (365) days from the date of purchase must be promptly communicated in writing to the
nearest authorized KMDSI dealer or (if no such dealer in the buyer’s country) contact KMDSI directly
at (805) 928-7772. No Product returns will be accepted by KMDSI without a returned merchandise
authorization (RMA) number from KMDSI. Upon receipt of the RMA from KMDSI, the buyer should
return the defective Product or part, freight prepaid, to an authorized KMDSI dealer or the KMDSI plant, as
directed by the RMA. KMDSI will repair or replace the Product at no charge, within a reasonable time, as it
deems necessary.
This warranty becomes null and void if:
1) The Product is not registered with KMDSI within ten (10) days of purchase, or
2) The Product has not been properly serviced and/or maintained according to KMDSI factory rec-
ommended procedures described in the manual or Product updates have not been performed as
recommended by KMDSI, or
3) Unauthorized attachments or modications have been made to the Product, or
4) The Product has been used for purposes other than those for which it was designed, or otherwise
has been abused, misused, or subjected to unusual conditions, or the Product’s intended service has
been exceeded.
EXCEPT AS SPECIFICALLY PROVIDED HEREIN, THERE ARE NO OTHER WARRANTIES,
EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES
FOR MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. THE PRODUCT
COVERED BY THIS WARRANTY IS MARKETED AND SOLD BY KMDSI SOLELY FOR COM-
MERCIAL OR INDUSTRIAL USE AND IS NOT A CONSUMER PRODUCT INTENDED FOR
PERSONAL, FAMILY, OR HOUSEHOLD USE.
In purchasing any Product subject to this warranty, the buyer agrees that its sole and exclusive remedy and
KMDSI’s entire obligation in contract, tort, or otherwise under this contract will be repair or replacement at
KMDSI’s option of the Product or any parts which KMDSI determines during the applicable warranty pe-
riod are defective in workmanship or material covered by this warranty. All exchanged parts are the property
of KMDSI. The buyer’s exclusive remedy and the KMDSI’s entire liability in contract, tort, or otherwise is
the payment by KMDSI of the buyer’s actual damages up to but not to exceed the amount paid by the buyer
for the Product.
In no event shall KMDSI be liable to the buyer for indirect, special, incidental or consequential damages (in-
cluding, but not limited to, damages for lost prots, lost sales, loss of business opportunity, or for injury to
persons or property arising out of the use of the Product). Any claim or action for breach of warranty must
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 III
be commenced within one year following delivery of the Product to the buyer.
Buyer acknowledges that this warranty is the sole and exclusive warranty of the Product and that it super-
sedes any and all oral or written representations and undertakings between KMDSI, its dealers, and the
buyer relating to the Products. This warranty allocates the risks of product failure between KMDSI and the
buyer, which allocation is recognized by both parties and is reected in the price of the goods. The buyer
acknowledges that it has read this agreement, understands it, and is bound by its terms.
IV © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
It is the responsibility of the owner of this product to register their ownership with Kirby Morgan Dive
Systems, Inc., by sending the warranty card provided. This card is to establish registration for any necessary
warranty work and as a means of communication that allows KMDSI to contact the user regarding this product.
The user must notify KMDSI of any change of address by the user or sale of the product.
All changes or revisions to this manual must be recorded in this document to ensure that the manual is
up to date. Quantities marked in parenthesis.
Record Of Changes
Change Number Date Description of Change
105/16/2008 Reworded: 2.1 Product Specications, 2.2.1 SuperFlow®and SuperFlow®350
Demand Regulators, 2.2.2 SuperFlow® 450 Performance Certication and 2.5
Operational Specications & limitations.
Reworded Warnings: Page 23 (2) and page 32.
Temperature limitations on page 24 changed from 36º F to 33º F.
Changed regulator adjustment knob to Flex Knob on page 102. Location number
in second NOTE on page 102 changed to reect correct location
Added: Appendix 3 and 4.
2 08/19/2008 Page III Removed page number column.
Page 17: Updated CE approved graphic on SL-17A/B
Page 18: Added CE approved graphic to KM-47 helmet. Updated CE approved
graphic on SL-27.
Page 20: Updated CE approved graphic on EXO-BR.
Pages 57-58: Moved chapter 5 into two columns.
Page 87: Added gasket warning on page 90 left column.
Page 158-159: Changed torque specications. Overset text arranged on next page
(159).
3 11/05/2008 Added D-Ring to Image on pages 17, 28, and 29.
Blowapart Image Updated with D-Ring on page 32, 38, 129, and 134.
Text Updated on pages 57-58, 131.
Rearranged pages 146-148, added diagram of earphone wire.
Appendix A1: Torque Specications updated on page 158.
4 02/25/2009 Text Updated on pages 144-145.
5 03/11/2009 Page 69, step 7; page 132 step 7; page 133 step 11; page 136 step 3; page 151
step 10: Changed kg cm to Newton Meters.
Page 71: Lacquer thinner changed to acetone.
Page 72: Corrected 35 inch pounds to 20 inch pounds in step 4. Lacquer thinner
changed to acetone.
Page 90: Corrected 75 inch pounds to 100 inch pounds in step 19.
Page 102: Section 7.12.2 “SuperFlow®450 Demand Regulator Test for Correct
Adjustment, Fully Assembled,” renumbered to aforementioned section number
from incorrect 7.12.1.
Page 117: Corrected 75 inch pounds to 100 inch pounds in step 8.
Page 121: Corrected 35 inch pounds to 20 inch pounds in step 3.
Page 123: Lacquer thinner changed to acetone.
Page 124: Corrected 35 inch pounds to 20 inch pounds in step 4. Lacquer thinner
changed to acetone.
Page 158: Added Location # 104a 530-020 Screw, exhaust ange.
Page 159: Added location # 176 550-533 Bent tube adapter, 450 Regulator.
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 V
607/27/2009 Added sections 2.1, 2.2, 2.2.1 and 2.2.2 for CE certication.
7 09/09/2009 Page 64 Section 6.4 step 5 text updated.
811/06/2009 Chapter 2: addition of CE conforming criteria.
2.3 Product Specications corrected weight to 32.6 lbs from 30.6 lbs.
9 03/17/2010 Updated images and diagrams with new whiskers
10 02/18/2011 Updated chapter 1.
11 03/23/2011 Updated earphones throughout manual
12 06/08/2011 Changed 61 meters to 67 meters in Appendix 3 Table 4 SuperFlow® / SuperFlow®
350 Regulator High Pressure Regulated Source and Appendix 3 Table 5 Supply
Pressure Guidelines SuperFlow® 450 Stainless Steel Balanced Regulators High
Pressure Regulated Source Supply Pressure Guidelines
13 10/17/2011 Updated CE notifying body number from 0496 to 2049
14 05/09/2012 Updated CE notifying body address
15 06/13/2012 Update copyright date to roman numerals
16 08/29/2012 Updated torque specs for updated BlowAparts
17 01/08/2013 Updated torque spec locations and copyright
Diving with compressed breathing gas is a hazardous activity. Even if you do everything
right there is always the potential for serious injury or death. No one piece of diving
equipment can prevent the possibility that you may be injured or killed any time you
enter the water. We do not herein make any effort to teach the principles of diving. The
information in this manual is intended for users of Kirby Morgan helmets and persons
that maintain or service Kirby Morgan helmets.
WARNING
VI © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
Table Of Contents
Warranty Information �������������������������������������������������������������������������������� II
Record Of Changes �������������������������������������������������������������������������������� IV
Denition of Signal Words Used in this Manual ������������������������������������������������ XIII
Chapter 1 General Information KMDSI Products����������������������������������� 1
1.1 Introduction �������������������������������������������������������������������������������������� 1
1.2 Full-Face Masks and Manifolds���������������������������������������������������������������� 2
1.3 Kirby Morgan Diving Helmets ������������������������������������������������������������������ 4
Chapter 2 Description & Operational Specications Kirby Morgan 37 &
57�������������������������������������������������������������������������������������������������������� 9
2.1 CR Marking �������������������������������������������������������������������������������������� 9
2.2 CE Certication ���������������������������������������������������������������������������������� 9
2�2�1 CE Marking ���������������������������������������������������������������������������������� 9
2�2�2 Notied Body ������������������������������������������������������������������������������� 10
2.3 Product Specications������������������������������������������������������������������������� 10
2.4 Regulator Performance ������������������������������������������������������������������������ 10
2�4�1 SuperFlow®and SuperFlow®350 Demand Regulators�������������������������������������� 10
2�4�2 SuperFlow®450 Performance �������������������������������������������������������������� 10
2.5 Cage Code �������������������������������������������������������������������������������������� 10
2.6 Operational Specications & Limitations ���������������������������������������������������� 10
2.7 Helmet Features �������������������������������������������������������������������������������� 11
2.8 General Description ���������������������������������������������������������������������������� 14
2�8�1 Helmet Shell �������������������������������������������������������������������������������� 14
2�8�2 Gas Flow Systems �������������������������������������������������������������������������� 14
2�8�3 Emergency Gas Supply System (EGS) ������������������������������������������������������ 18
2�8�4 Helmet Attachment to the Diver������������������������������������������������������������� 19
2�8�5 Sealing Arrangement ����������������������������������������������������������������������� 20
2�8�6 Reducing Carbon Dioxide ������������������������������������������������������������������ 20
2�8�7 Communications���������������������������������������������������������������������������� 20
2�8�8 Equalizing the Middle Ear ������������������������������������������������������������������� 20
2�8�9 Face Port or Viewing Lens ������������������������������������������������������������������ 21
2.9 Accessories ������������������������������������������������������������������������������������� 21
2�9�1 Eye Protection for Welding������������������������������������������������������������������ 21
2�9�2 Hot Water Shroud for SuperFlow®350������������������������������������������������������ 21
2�9�3 Special Regulator Tools for SuperFlow®350 ������������������������������������������������ 22
2.10 Helmet Transport And Storage �������������������������������������������������������������� 22
2�10�1 Helmet Carrying Bag ���������������������������������������������������������������������� 23
2.11 Use of Kirby Morgan Original Replacement Parts ����������������������������������������� 24
Chapter 3 Operating Instructions�������������������������������������������������������� 25
3.1 Introduction ������������������������������������������������������������������������������������� 25
3.2 Design Purpose��������������������������������������������������������������������������������� 25
3.3 First Use of Your Kirby Morgan Diving Helmet ���������������������������������������������� 26
3.4 Initial Adjustments to Your Helmet������������������������������������������������������������ 26
3�4�1 Head Cushion ������������������������������������������������������������������������������ 27
3.4.1.1 Head Cushion Removal ������������������������������������������������������������������� 27
3.4.1.2 Clean and Inspect ������������������������������������������������������������������������ 27
3.4.1.3 Stufng ���������������������������������������������������������������������������������� 27
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 VII
3.4.1.4 Head Cushion Adjustment ����������������������������������������������������������������� 27
3.4.1.5 Foam Trimming tips ����������������������������������������������������������������������� 27
3.4.1.6 Foam Stufng Tips ������������������������������������������������������������������������ 28
3.4.1.7 Adding Earphone Holes to the Head Cushion ������������������������������������������������ 28
3�4�2 Head Cushion Foam Spacer (HCFS) �������������������������������������������������������� 28
3.4.2.1 Installation of Head Cushion Foam Spacer (HCFS)�������������������������������������������� 28
3.4.2.2 Donning the Head Cushion Foam Spacer (HCFS)��������������������������������������������� 31
3.4.2.3 Maintenance of the Head Cushion Foam Spacer (HCFS) �������������������������������������� 32
3.4.2.3 Stufng the Head Cushion Foam Spacer (HCFS) ��������������������������������������������� 32
3�4�2 Trimming the Neck Dam �������������������������������������������������������������������� 32
3�4�3 Adjusting the Neck Pad��������������������������������������������������������������������� 33
3.5 Pre Dress-In Procedure ������������������������������������������������������������������������ 34
3�5�1 Pre-Dive Visual Inspection ������������������������������������������������������������������ 34
3.6 Preparing the Helmet for Diving��������������������������������������������������������������� 34
3�6�1 Clean Face Port ���������������������������������������������������������������������������� 34
3�6�2 Check Moving Parts ������������������������������������������������������������������������ 34
3�6�3 Check Communications �������������������������������������������������������������������� 36
3�6�4 One Way Valve Check ���������������������������������������������������������������������� 36
3.7 Emergency Gas System (EGS) ���������������������������������������������������������������� 36
3.8 Setting Up to Dive ������������������������������������������������������������������������������ 39
3�8�1 Flushing Out the Umbilical ������������������������������������������������������������������ 39
3�8�2 Connecting the Umbilical to the Helmet ���������������������������������������������������� 40
3�8�3 Opening the Breathing Gas Supply to the Helmet������������������������������������������� 40
3�8�4 Fogging Prevention ������������������������������������������������������������������������� 41
3�8�5 Donning The KM 37 or 57������������������������������������������������������������������� 41
3�8�6 Testing the Breathing System ��������������������������������������������������������������� 43
3�8�7 Adjust Regulator for Low Work Rates ������������������������������������������������������� 43
3�8�8 Sealing Integrity Check ��������������������������������������������������������������������� 43
3.9 Removing the Helmet �������������������������������������������������������������������������� 44
3.10 Diving Procedures ���������������������������������������������������������������������������� 44
3�10�1 Standing By to Dive ����������������������������������������������������������������������� 44
3�10�2 Attaching the Umbilical to the Harness ���������������������������������������������������� 44
3�10�3 Diver Dons Helmet ������������������������������������������������������������������������ 45
3�10�4 Diver Check Gas Flow Systems ����������������������������������������������������������� 45
3�10�5 Communications Check ������������������������������������������������������������������� 45
3�10�6 Diver Ready ������������������������������������������������������������������������������� 45
3�10�7 Water Entry and Descent ������������������������������������������������������������������ 45
3.11 Emergency Procedures ���������������������������������������������������������������������� 45
3�11�1 Flooding ����������������������������������������������������������������������������������� 45
3�11�2 Inhalation Resistance���������������������������������������������������������������������� 46
3�11�3 Gas Flow Stops ��������������������������������������������������������������������������� 46
3�11�4 Demand Regulator Free Flow�������������������������������������������������������������� 46
3.12 Post Dive Procedures ������������������������������������������������������������������������ 46
3�12�1 Removing the Equipment������������������������������������������������������������������ 46
3�12�2 Removing the Helmet ��������������������������������������������������������������������� 46
3�12�3 Storage of the Helmet Between Dives ����������������������������������������������������� 46
Chapter 4 Troubleshooting������������������������������������������������������������������ 49
4.1 General ������������������������������������������������������������������������������������������ 49
4.2 Communication Malfunction ������������������������������������������������������������������ 49
4.3 One Way Valve Malfunction ������������������������������������������������������������������� 49
VIII © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
4.4 Side Valve Malfunction������������������������������������������������������������������������� 50
4.5 Water Leakage Into Helmet ������������������������������������������������������������������� 50
4.6 Demand Regulator Malfunction��������������������������������������������������������������� 51
4.7 Emergency Gas Supply Valve ����������������������������������������������������������������� 51
Chapter 5 Inspection and Maintenance ����������������������������������������������� 53
5.1 Routine Maintenance �������������������������������������������������������������������������� 53
5�1�1 Daily Pre-Dive Maintenance A2�3 ����������������������������������������������������������� 53
5�1�2 Daily Post Dive Maintenance A2�6 ���������������������������������������������������������� 53
5�1�3 Supervisors Equipment Checks A2�4 and A2�5 ��������������������������������������������� 53
5.2 Monthly Maintenance �������������������������������������������������������������������������� 53
5.3 Yearly Maintenance ���������������������������������������������������������������������������� 53
5�3�1 Overhaul/Inspection Checklist A2�1��������������������������������������������������������� 53
Chapter 6 General Preventative Maintenance ������������������������������������� 55
6.1 Introduction ������������������������������������������������������������������������������������� 55
6.2 Required tools, Cleaning Agents, Lubrication ����������������������������������������������� 55
6�2�1 Component and Parts Cleaning������������������������������������������������������������� 56
6�2�2 Component and Parts Lubrication ���������������������������������������������������������� 56
6�2�3 Teon®Tape �������������������������������������������������������������������������������� 57
6�2�4 RTV Sealant �������������������������������������������������������������������������������� 57
6�2�5 Thread Locker ������������������������������������������������������������������������������ 57
6.3 General Cleaning & Inspection Procedures�������������������������������������������������� 57
6�3�1 O-Ring Removal/Inspection/Cleaning and Lubrication �������������������������������������� 58
6.3.1.1 O-Ring Removal: ������������������������������������������������������������������������ 58
6.3.1.2 O-Ring Inspection: ������������������������������������������������������������������������ 58
6.3.1.3 O-Ring Reuse:���������������������������������������������������������������������������� 58
6�3�2 General Cleaning Guidelines ��������������������������������������������������������������� 58
6.3.2.1 Mild Soap Solution for General Cleaning and Leak Detector Use ������������������������������� 59
6.3.2.2 Acidic Cleaning Solution and Procedures ���������������������������������������������������� 59
6.3.2.3 Germicidal Cleaning Solutions and Procedure ������������������������������������������������ 59
6.4 Daily Maintenance������������������������������������������������������������������������������ 60
6.5 Monthly Maintenance (or between jobs) ����������������������������������������������������� 61
6�5�1 Locking Collar Assembly & Helmet Ring ��������������������������������������������������� 61
6�5�2 Neck Dam Ring Assembly ������������������������������������������������������������������ 61
6�5�3 Head Cushion and Chin Cushion ����������������������������������������������������������� 62
6�5�4 Communications Inspection ���������������������������������������������������������������� 62
6�5�5 Lubricate Nose Block O-Rings�������������������������������������������������������������� 62
6.6 Inspect the Exhaust Valve ��������������������������������������������������������������������� 62
6�6�1 For Helmets Equipped with the Tri-Valve™ ������������������������������������������������� 62
6�6�2 For Helmets Equipped with the Quad Valve™ Exhaust ������������������������������������� 63
Chapter 7.0 Breathing System Maintenance and Repairs �������������������� 65
7.1 Introduction ������������������������������������������������������������������������������������� 65
7.2 One Way Valve ���������������������������������������������������������������������������������� 65
7�2�1 Disassembly Of The One Way Valve �������������������������������������������������������� 65
7�2�2 Reassembly of the One Way Valve���������������������������������������������������������� 66
7.3 Side Block Assembly��������������������������������������������������������������������������� 67
7�3�1 General ������������������������������������������������������������������������������������� 67
7�3�2 Side Block Assembly Removal�������������������������������������������������������������� 67
7�3�3 Separating the Side Block Assembly from the Helmet Shell �������������������������������� 67
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 IX
7�3�4 Side Block Assembly Replacement ��������������������������������������������������������� 68
7.4 Defogger Valve ��������������������������������������������������������������������������������� 70
7�4�1 Disassembly of the Defogger Valve ��������������������������������������������������������� 70
7�4�2 Cleaning and Lubricating ������������������������������������������������������������������� 71
7�4�3 Reassembly of the Defogger Valve���������������������������������������������������������� 71
7.5 Emergency Valve Assembly ������������������������������������������������������������������� 72
7�5�1 Disassembly of the Emergency Valve ������������������������������������������������������� 72
7�5�2 Cleaning and Lubricating ������������������������������������������������������������������� 73
7�5�3 Reassembly of Emergency Valve ����������������������������������������������������������� 74
7�5�4 Leak Testing the EGS Valve ����������������������������������������������������������������� 75
7.6 Bent Tube Assembly ��������������������������������������������������������������������������� 75
7�6�1 General ������������������������������������������������������������������������������������� 75
7�6�2 Removal of the Bent Tube Assembly�������������������������������������������������������� 76
7�6�3 Inspection of Bent Tube Assembly ���������������������������������������������������������� 76
7�6�4 Installation of the Bent Tube Assembly������������������������������������������������������ 76
7.7 SuperFlow®350 Demand Regulator ���������������������������������������������������������� 77
7�7�1 General Regulator Information �������������������������������������������������������������� 77
7�7�2 SuperFlow®350 Demand Regulator Test for Correct Adjustment, Fully Assembled ��������� 77
7�7�3 Inspection of SuperFlow®350 Regulator Body Interior ������������������������������������� 78
7�7�4 SuperFlow®350 Demand Regulator Bias Adjustment Servicing, Demand Regulator on the
Helmet�������������������������������������������������������������������������������������������� 78
7�7�5 Reassembly of the SuperFlow®350 Regulator Adjustment System ������������������������� 79
7�7�6 SuperFlow®350 Demand Regulator Removal from Helmet ��������������������������������� 80
7�7�7 Disassembly of the SuperFlow®350 Demand Regulator ������������������������������������ 81
7�7�8 Inspection of SuperFlow®350 Demand Regulator Parts ������������������������������������ 82
7�7�9 Reassembly of the SuperFlow®350 Demand Regulator ������������������������������������ 84
7�7�10 Tuning the SuperFlow®350 Regulator ����������������������������������������������������� 88
7�7�11 SuperFlow®350 Regulator Steady Flows When Pressured Up: Special Tools Used������� 90
7.8 Oral Nasal ��������������������������������������������������������������������������������������� 92
7�8�1 Oral Nasal General Information ������������������������������������������������������������� 92
7�8�2 Oral Nasal Removal ������������������������������������������������������������������������ 92
7�8�3 Inspection of Oral Nasal �������������������������������������������������������������������� 92
7�8�4 Oral Nasal Replacement �������������������������������������������������������������������� 93
7.9 Quad Valve™Exhaust Assembly �������������������������������������������������������������� 94
7�9�1 Quad Valve™Assembly Removal������������������������������������������������������������ 94
7�9�2 Quad Valve™Exhaust Valves ���������������������������������������������������������������� 95
7.9.2.1 Quad Valve™Exhaust Valve Replacement���������������������������������������������������� 95
7.9.2.2 SuperFlow®350 Regulator Exhaust Valve Replacement ��������������������������������������� 96
7�9�3 Quad Valve™Assembly Installation ��������������������������������������������������������� 96
7.10 Water Dump Exhaust Body ������������������������������������������������������������������ 97
7�10�1 Water Dump Valve Removal ��������������������������������������������������������������� 97
7�10�2 Water Dump Valve Replacement ���������������������������������������������������������� 97
7�10�3 Water Dump Valve Body Removal ��������������������������������������������������������� 97
7�10�4 Water Dump Valve Body Remounting ����������������������������������������������������� 97
7.11 Reinstalling the Quad Valve™Exhaust Assembly ������������������������������������������ 98
7�12 SuperFlow®450 Stainless Balanced Regulator ���������������������������������������������� 99
7�12�1 General������������������������������������������������������������������������������������ 99
7�12�2 SuperFlow®450 Demand Regulator Test for Correct Adjustment, Fully Assembled�������� 99
7�12�3 Adjusting the SuperFlow®450 ����������������������������������������������������������� 100
X © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
7�12�4 SuperFlow®450 Demand Regulator Bias Adjustment Field Service with Demand Regulator
on Helmet ���������������������������������������������������������������������������������������101
7�12�5 SuperFlow®450 Regulator Removal����������������������������������������������������� 106
7�12�6 SuperFlow®450 Disassembly ����������������������������������������������������������� 107
7�12�7 Assembly of the SuperFlow®450 Regulator ��������������������������������������������� 109
7.12.7.1 Assembly of the Flex Knob�������������������������������������������������������������� 109
7.12.7.2 Assembly of SuperFlow®450 Regulator ��������������������������������������������������� 110
7�12�8 SuperFlow®450 Regulator Installation����������������������������������������������������114
Chapter 8 Corrective Maintenance�����������������������������������������������������117
8.1 General �����������������������������������������������������������������������������������������117
8.2 Helmet Shell Inspection�����������������������������������������������������������������������117
8.3 Nose Block Assembly�������������������������������������������������������������������������118
8�3�1 Nose Block Assembly Removal������������������������������������������������������������118
8�3�2 Nose Block Device Replacement ����������������������������������������������������������119
8.4 Handle and Weights�������������������������������������������������������������������������� 120
8�4�1 Handle Removal ������������������������������������������������������������������������� 120
8�4�2 Handle Replacement ��������������������������������������������������������������������� 120
8�4�3 Side Weight Removal ��������������������������������������������������������������������� 120
8�4�4 Port Weight Replacement����������������������������������������������������������������� 122
8�4�5 Top Weight�������������������������������������������������������������������������������� 123
8.4.5.1 Top Weight Removal �������������������������������������������������������������������� 123
8.4.5.2 Top Weight Replacement ���������������������������������������������������������������� 123
8.5 Face Port�������������������������������������������������������������������������������������� 124
8�5�1 General ����������������������������������������������������������������������������������� 124
8�5�2 Face Port and Nose Block Device Removal����������������������������������������������� 124
8�5�3 Face Port and Nose Block Replacement�������������������������������������������������� 126
8�5�4 Special Note Regarding Ports ������������������������������������������������������������ 127
8.6 Neck Ring Assembly ������������������������������������������������������������������������ 128
8�6�1 General Information on Neck Dams������������������������������������������������������� 128
8�6�2 Removal of the Neck Dam ���������������������������������������������������������������� 128
8�6�3 Neoprene Neck Dam Replacement ������������������������������������������������������� 128
8�6�4 Latex Neck Dam Replacement������������������������������������������������������������ 131
8�6�5 Trimming a Latex Neck Seal �������������������������������������������������������������� 132
8.7 Pull Strap�������������������������������������������������������������������������������������� 133
8�7�1 Pull Strap Removal ����������������������������������������������������������������������� 133
8�7�2 Pull Strap Replacement������������������������������������������������������������������� 133
8.8 Chin Strap������������������������������������������������������������������������������������� 133
8�8�1 Chin Strap Removal ���������������������������������������������������������������������� 133
8�8�2 Chin Strap Replacement������������������������������������������������������������������ 133
8.9 O-Ring Seal Replacement ������������������������������������������������������������������ 134
8.10 Helmet Ring ��������������������������������������������������������������������������������� 135
8�10�1 Helmet Ring Repairs��������������������������������������������������������������������� 135
8.11 Sealed Pull Pins ����������������������������������������������������������������������������� 135
8�11�1 Removal of Sealed Pull Pins������������������������������������������������������������� 135
8�11�2 Replacement of Sealed Pull Pins �������������������������������������������������������� 135
8.12 Swing Tongue Catch ����������������������������������������������������������������������� 136
8�12�1 Disassembly of the Swing Tongue Catch ������������������������������������������������ 136
8�12�2 Reassembly of the Swing Tongue Catch������������������������������������������������� 136
8.13 Locking Collar/Neck Pad������������������������������������������������������������������� 138
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 XI
8�13�1 Locking Collar Removal ����������������������������������������������������������������� 138
8�13�2 Locking Collar Disassembly������������������������������������������������������������� 139
8�13�3 Locking Collar Reassembly�������������������������������������������������������������� 140
8.15 Head Cushion (pre October 2012)��������������������������������������������������������� 142
8�15�1 Head Cushion Foam��������������������������������������������������������������������� 142
8.16 Chin Cushion Foam������������������������������������������������������������������������� 142
8.15 Communications System������������������������������������������������������������������� 143
8�15�1 General���������������������������������������������������������������������������������� 143
8�15�2 Earphone Inspection �������������������������������������������������������������������� 143
8�15�3 Removal of Communications Assembly ������������������������������������������������� 144
8�15�4 Replacement of Communications Assembly��������������������������������������������� 144
8�15�5 Microphone Replacement ��������������������������������������������������������������� 145
8�15�6 Earphone And Wire Assembly Replacement��������������������������������������������� 145
8�15�7 Waterproof Connector������������������������������������������������������������������� 146
8.15.7.1 Connector Removal�������������������������������������������������������������������� 146
8.15.7.2 Connector Replacement���������������������������������������������������������������� 147
8�15�8 Terminal Connections in the Waterproof Connector ������������������������������������� 147
8�15�9 Communications Posts������������������������������������������������������������������ 149
8.15.9.1 Communications Post Removal ��������������������������������������������������������� 149
8.15.9.2 Communications Post Replacement ����������������������������������������������������� 149
Chapter 9 Accessories for the Kirby Morgan 37 & 57 ������������������������ 151
9.1 Introduction ����������������������������������������������������������������������������������� 151
9.2 Hot Water Shroud for KM37 ����������������������������������������������������������������� 151
9�2�1 Hot Water Shroud Installation Procedures for KM37 �������������������������������������� 151
9.3 Low Pressure Inator Hose������������������������������������������������������������������ 154
9�3�1 Installation of the Low Pressure Inator Hose ��������������������������������������������� 154
9.4 Weld Lens Assembly������������������������������������������������������������������������� 155
9�4�1 Weld Lens Assembly Installation ���������������������������������������������������������� 155
9.5 Weld Shield Assembly ����������������������������������������������������������������������� 156
9�5�1 Weld Shield Assembly Installation �������������������������������������������������������� 156
9.6 Use of Quick Disconnect �������������������������������������������������������������������� 156
9.7 Accessory Mounting Brackets �������������������������������������������������������������� 157
9�7�1 Mount Bracket Installation ���������������������������������������������������������������� 157
Table of Equivalents�������������������������������������������������������������������������� 159
Appendix 1: Torque Specications ���������������������������������������������������� 160
KM 37 Torque Tables ����������������������������������������������������������������������������� 160
KM 57 Torque Table ������������������������������������������������������������������������������ 161
Appendix 1: Torque Specications Continued������������������������������������ 161
Note on Torque Specications ���������������������������������������������������������� 163
Appendix A2 Maintenance and Inspection Procedures ���������������������� 164
Appendix 3 Supply Pressure Requirements & Tables ������������������������� 166
Appendix 3 Table 1 Work Rate Expressed as Respiratory Minute Volume (RMV)* ��������� 167
Appendix 3 Table 2 Compressor Supply Table SuperFlow®and SuperFlow®350���������� 167
Appendix 3 Table 3 SuperFlow®450 SS Balanced Regulator �������������������������������� 168
Appendix 3 Table 4 SuperFlow®/ SuperFlow®350 RegulatorHigh Pressure Regulated
Source ��������������������������������������������������������������������������������������������� 170
Appendix 3 Table 3 SuperFlow®450 SS Balanced Regulator Continued ������������������� 170
Appendix 3 Table 5 Supply Pressure Guidelines SuperFlow®450 Stainless Steel Balanced
XII © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
Regulators High Pressure Regulated Source Supply Pressure Guidelines ����������������� 171
Appendix 4 Standard Kirby Morgan Surface Supply Pressure Formula -
Old Method��������������������������������������������������������������������������������������� 171
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 XIII
CAUTION
For your protection, pay particular attention to items identied by signal words in this manual. These terms are identied
as, CAUTION, WARNING AND DANGER. It is especially important for you to read and understand these sections.
This word indicates an imminently hazardous situation, which if not avoided, could re-
sult in death or serious injury.
This word indicates a potentially hazardous situation, which, if not avoided, could result
in death or serious injury.
This word indicates a potentially hazardous situation, which if not avoided, may result in
minor or moderate injury. It may also be used to alert against unsafe practices.
If English is not your native language and you have any difficulty understanding the language of
any warnings as they appear in the manual, please have them translated.
Este é um aviso importante. Queira mandá-lo traduzir.
Este es un aviso importante. Sirvase mandario traducir.
Quest è un avviso importante. Tradurlo.
Ceci est important. Veuillez traduire.
Diese Mitteilung ist wichtig. Bitte übersetzen lassen.
If you have any questions concerning this manual or the operation of your helmet, contact KMDSI (805) 928-7772 or
by Email at [email protected] or Dive Lab Inc. (850) 235-2715 or at [email protected]
IMPORTANT: A word about this manual. We have tried to make this manual as comprehensive and factual
as possible. We reserve the right however, to make changes at any time, without notice, in prices, colors, materials,
equipment, specications, models and availability. Since some information may have been updated since the time
of printing, please contact your local KMDSI dealer if you have any questions. Periodically KMDSI Operations and
Maintenance Manuals are reviewed. Any updates/changes will be posted on the KMDSI website and may be down-
loaded for insertion/correction.
Important Safety Information:
This Kirby Morgan diving helmet is intended for use by trained divers who have successfully completed a recognized
training course in surface supplied diving.
Definition of Signal Words Used in this Manual
DANGER
WARNING
WARNING
WARNING
WARNING
WARNING
WARNING
XIV © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
DANGER
Follow all the instructions in this manual carefully and heed all safety precautions. Im-
proper use of this diving helmet could result in serious injury or death.
Kirby Morgan Dive Systems, Inc. (KMDSI) warns all divers who use the Kirby Morgan
diving helmet to be sure to use only KMDSI original parts from a KMDSI authorized deal-
er. Although other parts, O-rings and fittings may appear to fit on Kirby Morgan diving
helmets, they may not be manufactured to the same standards maintained by KMDSI.
The use of any parts other than KMDSI original parts may lead to equipment failure and
accidents.
Diving in waters that are chemically, biologically, or radiologically contaminated is ex-
tremely hazardous. Although Kirby Morgan diving helmets may be adapted for use in
some contaminated environments, special training, equipment, and procedures are
necessary. Do not dive in a contaminated environment unless you have been thoroughly
trained and equipped for this type of diving.
Read this manual before using or maintaining the helmet, even if you have experience with other diving helmets. If
you have purchased the helmet new from a dealer, be sure to send in the warranty registration card so we may
keep you informed of any safety notices that affect this product. If you resell or loan this helmet to another diver,
be sure this manual accompanies the helmet and that the person reads and understands the manual. In addition to the
manual a log book should be used to log all repairs, maintenance and use.
Diving is a life threatening occupation. Even if you do everything right you can still be
killed or injured. None of the models of Kirby Morgan helmets or masks can prevent ac-
cidents, injuries or death due to improper training, poor-health, improper supervision,
improper job requirements, improper maintenance or acts of God.
This helmet was completely checked and should be ready to dive as it was shipped from
the factory. However, it is always the diver’s responsibility to check all the components
of the helmet prior to diving.
Any and all fiberglass repairs done to this helmet MUST be done by a KMDSI factory
trained repair facility. Painting is not recommended by KMDSI. Furthermore, many diving
companies will not allow painted helmets to be used because painting can mask previ-
ous fiberglass damage. KMDSI certified technicians are not responsible for certifying
helmets free from damage during annual overhauls.
Helmet shells can be re-gel coated by authorized/certified KMDSI trained technicians
that have received fiberglass training by KMDSI. Helmets that are to be painted for cos-
metic purposes, should be first, certified free of fiberglass damage by an authorized
KMDSI technician certified in fiberglass repair. A log entry should be made in the hel-
met log that the helmet was free of damage prior to painting. Keep in mind other KMDSI
technician can refuse to work on helmet shells that have previously been painted or
repaired by non KMDSI certified persons.
This manual is supplied to the original purchaser of this helmet. If you have any questions about the use of the helmet
or you need another copy of this manual, Part Number 100-073, contact KMDSI or your nearest KMDSI dealer or
may be downloaded free from the KMDSI website at www.KirbyMorgan.com.
WARNING
DANGER
DANGER
WARNING
WARNING
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 XV
If you have any questions regarding the use, maintenance, or operation of this helmet, contact KMDSI at (805) 928-
7772, fax: (805) 928-0342, or e-mail: [email protected].
Kirby Morgan masks and helmets are cleaned and lubricated for oxygen ser-
vice when they come from the factory. However, if the helmet is used with an
oil lubricated air compressor, contamination with hydrocarbons may result.
If the breathing system in the helmet is exposed to hdrocarbons, it must be
cleaned for oxygen service and lubricated with oxygen safe lubricants before
using it again with breathing mixtures containing a high percentage of oxy-
gen. If this is not done, fires and explosions may result, exposing the user to
serious personal injury or death.
Components requiring lubrication, should only be lubricated with oxygen compatible lubricants such as Christo-
Lube®, Fluorolube®, or Krytox®. Lubricants must be used sparingly and should not be mixed with other lubricants.
KMDSI helmets and masks are intended for underwater use only and should only be
used by qualified divers that have received proper training in the use of this type of
equipment. KMDSI helmets and masks should not be used or worn without the appro-
priate life support systems, such as air or gas supplies and support personnel as de-
scribed in this manual.
KMDSI helmets and masks should never be used for motor sport racing, aviation /
space craft use, or for chemical warfare use. The helmet must never be used by persons
in poor physical condition, by persons with previous head neck or back injuries which
could be aggravated by its use. The helmet should not be used by persons under the in-
fluence of drugs or alcohol. Furthermore, infants, children, or persons under the age of
18 should never wear KMDSI helmets and masks. Failure to pay heed to the above could
result in serious injury or death.
Never use the helmet without first completing all pre-dive maintenance and set up pro-
cedures.
Do not use KMDSI masks or helmets in currents exceeding 3.0 knots Use in currents
greater than 3 knots may allow water to enter the exhaust valve, possibly causing regu-
lator flooding.
Surface-supplied diving can be a strenuous activity. Most Kirby Morgan helmets weigh
in excess of 27 pounds. KMDSI recommends that persons with a previous neck or back
injury seek professional medical approval prior to engaging in surface supplied diving
operations using any Kirby Morgan helmet. Use of any Kirby Morgan helmet with a pre-
existing physical/medical condition may result in death or serious injury.
The information contained in this manual is intended to aid the user in optimizing the performance of this helmet.
The application of some of this information will depend on the diving situation and the use of associated equipment.
Many countries have specic laws and rules regarding commercial diving. It is important for the user to understand
the rules, regulations, and philosophy imposed by the governing, regulating bodies whenever using commercial diving
equipment.
Whenever KMDSI helmets or masks are used in European Countries, which have adopted the C.E. certication pro-
grams, they must only be used with C.E. certied components. Diving operations should only be conducted within the
DANGER
DANGER
WARNING
DANGER
WARNING
XVI © ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001
Kirby Morgan®37 & 57
limits of the operational specications, and in accordance with the rules and regulations established by the governing
authority in the specic country or geographical location where the diving operations are being conducted. If you have
any questions concerning this manual or the operation of your helmet, contact KMDSI (805) 928-7772 or at
[email protected] or Dive Lab Inc. (850) 235-2715 or at [email protected]
Kirby Morgan®37 & 57
© ⅯⅯⅩⅣ Kirby Morgan Dive Systems, Inc. All rights reserved. Document #140205001 XVII
The Kirby Morgan 37 helmet
C
O
M
M
E
R
C
I
A
L
L
Y
R
A
T
E
D
-
P
R
O
F
E
S
S
I
O
N
A
L
D
I
V
I
N
G
G
E
A
R
-
D
I
V
E
L
A
B
T
E
S
T
E
D
™
Defog Free Flow
Valve Knob
Regulator Adjustment
Knob
Equalization Device
Oral Nasal Mask
Port Retainer
Handle
Purge Button
Helmet Shell
Communications Port
Quad Valve™ Exhaust
(standard on all Kirby Morgan 37
helmets from 2005 on)
Sideblock
EGS Valve
Pull Pin
Non-Return Valve

Other Kirby Morgan Diving Instrument manuals

Kirby Morgan One Way Valve User manual

Kirby Morgan

Kirby Morgan One Way Valve User manual

Kirby Morgan M-48 SuperMask User manual

Kirby Morgan

Kirby Morgan M-48 SuperMask User manual

Kirby Morgan SuperLite 27 User manual

Kirby Morgan

Kirby Morgan SuperLite 27 User manual

Kirby Morgan 525-100 User manual

Kirby Morgan

Kirby Morgan 525-100 User manual

Kirby Morgan SuperFlow 525-757 User manual

Kirby Morgan

Kirby Morgan SuperFlow 525-757 User manual

Kirby Morgan KM 37 User manual

Kirby Morgan

Kirby Morgan KM 37 User manual

Kirby Morgan 525-769 User manual

Kirby Morgan

Kirby Morgan 525-769 User manual

Kirby Morgan 510-674 User manual

Kirby Morgan

Kirby Morgan 510-674 User manual

Kirby Morgan 100-075 User manual

Kirby Morgan

Kirby Morgan 100-075 User manual

Kirby Morgan 37 User manual

Kirby Morgan

Kirby Morgan 37 User manual

Kirby Morgan 200-120 User manual

Kirby Morgan

Kirby Morgan 200-120 User manual

Kirby Morgan SuperMask MOD-1 User manual

Kirby Morgan

Kirby Morgan SuperMask MOD-1 User manual

Kirby Morgan M-48 MOD-1 User manual

Kirby Morgan

Kirby Morgan M-48 MOD-1 User manual

Kirby Morgan MOD-1 User manual

Kirby Morgan

Kirby Morgan MOD-1 User manual

Kirby Morgan KMB 18 User manual

Kirby Morgan

Kirby Morgan KMB 18 User manual

Kirby Morgan SuperLite 17C Helmet User manual

Kirby Morgan

Kirby Morgan SuperLite 17C Helmet User manual

Kirby Morgan KMB-18 A/B User manual

Kirby Morgan

Kirby Morgan KMB-18 A/B User manual

Kirby Morgan EXO Full-Face Mask Manual

Kirby Morgan

Kirby Morgan EXO Full-Face Mask Manual

Kirby Morgan M-48 MOD-1 User manual

Kirby Morgan

Kirby Morgan M-48 MOD-1 User manual

Kirby Morgan SuperLite 27 User manual

Kirby Morgan

Kirby Morgan SuperLite 27 User manual

Kirby Morgan 525-757 User manual

Kirby Morgan

Kirby Morgan 525-757 User manual

Kirby Morgan 77 User manual

Kirby Morgan

Kirby Morgan 77 User manual

Kirby Morgan EXO original Manual

Kirby Morgan

Kirby Morgan EXO original Manual

Kirby Morgan SuperLite 17B User manual

Kirby Morgan

Kirby Morgan SuperLite 17B User manual

Popular Diving Instrument manuals by other brands

Shearwater Petrel 2 Release notes

Shearwater

Shearwater Petrel 2 Release notes

Azoth Systems O'Dive Complete Instructions Manual

Azoth Systems

Azoth Systems O'Dive Complete Instructions Manual

Aqua Lung i100 owner's manual

Aqua Lung

Aqua Lung i100 owner's manual

Johnson Outdoors Scubapro Uwatec A 700 2nd Stage Maintenance Procedure

Johnson Outdoors

Johnson Outdoors Scubapro Uwatec A 700 2nd Stage Maintenance Procedure

Xtreme X-Fish 151 user manual

Xtreme

Xtreme X-Fish 151 user manual

Tusa RS1207 user guide

Tusa

Tusa RS1207 user guide

Uwatec GALILEO quick start guide

Uwatec

Uwatec GALILEO quick start guide

Marcum Technologies Underwater Viewing System VS 400 instruction manual

Marcum Technologies

Marcum Technologies Underwater Viewing System VS 400 instruction manual

Uwatec DC-12 owner's manual

Uwatec

Uwatec DC-12 owner's manual

Oceanic DATA PLUS owner's guide

Oceanic

Oceanic DATA PLUS owner's guide

Aqua Lung Calypso Service manual

Aqua Lung

Aqua Lung Calypso Service manual

Dive Rite BC1080 quick start guide

Dive Rite

Dive Rite BC1080 quick start guide

O'Three Aquatherm instruction manual

O'Three

O'Three Aquatherm instruction manual

Divertug DT 12/Combi operating instructions

Divertug

Divertug DT 12/Combi operating instructions

Oceanic XTC-100 owner's guide

Oceanic

Oceanic XTC-100 owner's guide

TecLINE R2 TEC user manual

TecLINE

TecLINE R2 TEC user manual

Novasub SCC-1DR Operation manual

Novasub

Novasub SCC-1DR Operation manual

Suunto VYPER NOVO user guide

Suunto

Suunto VYPER NOVO user guide

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.