KitchenAid Pro Line KGCP462K User manual

[] []
backguard
(required for some insta{lations)
/
36" (91.4 cm) cooktop with all
sealed burners shown
I_Jtchen_Jd _
FOR TH E WAY IT'S MADE _'
Questions regarding features,
operation, performance, parts or
service? Call 1-800o422-1230 or visit
our web site at www.kitchenaid.com.
Readandsa_ethese
IMPORTANT:
Installer: Leave installation
instructions with the homeowner.
Homeowner: Keep installation
instructions for future reference.
Save installation instructions for local
electrical inspector's use.
Write down the model and serial numbers
before installing cooktop.
Both numbers are on the model/serial
number plate, located on the left front
underside of the cooktop burner box.
Model #
Serial # Part No. 8285479

Before youstart,,,
Your safety and the safety of
others are very important,
We have provided many important
safety messages in this manual and
on your appliance. Always read and
obey all safety messages.
This is the safety alert
symbol.
This symbol alerts you to
potential hazards that can kill or hurt
you and others.
All safety messages will follow the
safety alert symbol and either the
word "DANGER" or "WARNING".
These words mean:
You can be killed or seriously
injured if you don't immediately
foltow instructions.
You can be killed or seriously
injured if you don't follow
instructions.
All safety messages will tell you
what the potential hazard is, tell you
how to reduce the chance of injury,
and tell you what can happen if the
instructions are not followed.
Important: Observe all governing
cedes and ordinances,
in the State of Massachusetts, the
following installation instructions
apply:
• installations and repairs must be
performed by a qualified or licensed
contractor, plumber, or gasfitter
qualified or licensed by the State of
Massachusetts.
• If using a ball valve, it shall be a
Tzhandie type.
• A flexible gas connector, when used,
must not exceed 3 feet.
WARNING: _fthe
information in this manua_
is not followed exactly, a
fire or expRosion may result
causing property damage,
persona_ injury or death.
m Do not store or use
gasoline or other
flammable vapors and
_iquids in the vicinity of
this or any other
appliance.
WHAT TO DO _FYOU
SMELL GAS
o Do not try to _ight any
appliance.
o Do not touch any
eRectrica_ switch.
oDo not use any phone in
your building.
o_mmediatemy call your
gas supplier from a
neighbor's phone. Follow
the gas supp_ier's
instructions.
o_fyou cannot reach your
gas supplier, call the fire
department.
_nstaHation and service
must be performed by a
qualified installer, service
agency or the gas
supplier.
The California Safe Drinking Water and
Toxic Enforcement Act requires the
Governor of California to publish a list of
substances known to the State of
California to cause cancer, birth defects,
or other reproductive harm, and requires
businesses to warn of potential exposure
to such substances.
WARNING: This product contains a
chemical known to the State of California
to cause cancer, birth defects, or other
reproductive harm.
This appliance can cause Iowolevel
exposure to some of the substances
listed, including benzene, crystalline silica,
carbon monoxide, toluene, and soot.
NOTE: This cooktop is manufactured for
use with Natural gas. To convert to
LR/Propane gas, see the Gas
Conversion instructions provided in
literature package.
Proper gas supply connection must be
available. See "Gas supply requirements."
Proper installation is your responsibility.
Have a qualified technician install this
cooktoF
Make sure you have everything
necessary for correct installation. It is the
responsibility of the installer to comply
with the installation clearances specified
on the model/serial rating plate. The
model/serial rating plate can be found on
the underside of the cooktop burner box.
It is recommended that an overhead vent
hood be used with this cooktoF For
island installations, a 48" (122 cm) hood
is recommended.
Check location where cooktop will be
installed. The location should be away
from strong draft areas, such as windows,
doors and strong heating vents or fans.
Do not obstruct flow of combustion and
ventilation air.
All openings in the wall or floor where the
cooktop is to be installed must be sealed.
Etectdcal ground is required. See
"Electrical Requirements."
It is the customer's responsibility:
To contact a qualified electrical
installer.
To assure that electrical installation is
adequate and in conformance with
Nationam Electrical Code, ANSt/NFPA
70 -- latest edition*, or Canadian
Electrical Code, C22.1 o1982 and C22.2
No. 01982 (or Jatest edition)** and aH
local codes and ordinances.
Copies of the standards listed may be obtained
from:
* Nationa_ Fire Protection Association
One Batterymarch Park
Quincy', Massachusetts 02268
** CSA Internationa_
8501 East Pmeasant Valley Rd.
C_eveJand, Ohio 44161-5575

P Dimensions
26-1/4" (6&7 crn)
718"==4_
(222 mm)
2-3/16" _ 14
(55,6mm)
I
I
22" (55,9 cm)
side view of cooktop
÷
for 48" (121,9 cm)
8 burner model only:
3/8" 8" (16.2 cm)
(&5 mm) all otber models:
9" (22.8 cm)
I7=1_8,,
(16,1 cm)
{
gas inlet isIooated 1=718"(4,8 cm) from
-- back of burner box and
4-7/8" (12.4 cm) in from LH, side of
burner box
_e--=1=3/16"
(3&2 mm)

Cabinet a Cutout imensions
Countertop opening and clearance
dimensions that are shown must be
used. Given dimensions provide required
clearances.
Mobile home installation: The
installation of this cooktop must conform
to the Manufactured Home Construction
and Safety Standards, Title 24 CFR, Part
3280 (formerly the Federal Standard for
Mobile Home Construction and Safety;
Title 24 HUD part 280); or when such
standard is not applicable, the Standard
for Manufactured Home Installations
(Manufactured Home Sites, Communities
and Setups), ANSI A225.1 -- latest
edition*, or with local codes.
In Canada, the installation of this cooktop
must conform with the current standards
CAN/CSA=Z240 -- latest edition**, or with
local codes.
The cooktop is designed to hang from the
countertop by its side and rear flanges.
The gas and electric supply should be
located as shown in "Gas and Electric
Dimensions," so that they are accessible
without requiring removal of the cooktop.
Provide cutout in left rear corner of cutout
enclosure as shown to provide clearance
for gas inlet, power supply cord, and to
allow the rating label to be visible.
Copies of the standards listed may be
obtained from:
* Nationat Fire Protection Association
One Batterymarch Park
Quincy, Massachusetts 02269
** CSA Internationa_
8501 East P_easant Valley Rd.
C_eveiand, Ohio 44131-8578
7-1/4"
(18.4cm) _3/4" (1.9 cm)
/
(lZJ cmI
12o5/16" (31.3 cral
mira clearance to
side wall -
both sides
CORNER NOTCH
RETAIL
(51cm)
basecabinet
size
35" (91.4 cm)
46" (121,9 cmI
model
KGCP462K
KGCP463K
KGCP457J
KGCP462K
KGCP483K
KGCP484K
KGCP487J
islandtrim
5"
(12.7 cm)
6II
(15.2 cm}
5"
(12,7 cm)
5" (15.2 cm)
5"
(12.7 cm}
A
backgaard
1o3/4"
(4.4 cm)
1=3/4"
(4.4 cm)
5 I,
(12.7 cm)
B(_i,.)
islaed trim backgoard
48" (121.9 cm)
48" (121.9 cm)
48" 48"
(121.9 cm) (121.9 cm)
48"
(121.9 cm)
48" (121.9 cml
g
baokguard
opening
36"
(91.4 cm)
D
cabinetaod
coantertop
35-1/4"
(89.5 cm)
coanieriop only
36" (91.4 cmI or
35-7/8" (91,1 cm)
for zero dearaoce tit
48" (121.9 cmIor
47o7/8" (121.6 cm)
for zero clearance lit
Note: Dimension "B" CaBbe reduced by 5" (15.2 cm) when bottom ot wood or metal cabieei is protected by notloss than 825" (6.4 ram) flame retardant
millboard covered with n0t less tbae No. 26 [V]SGsheet steel, 8.815" (8.4 [am) stainless steel, 0.024" (8.5 mm! alumieum or 8.828" (8.5 [amI copper.

product rating/aerialfag
Note: Solidsideand
bottomofcutout
enclosurenotshown,
Explosion Hazard
Use a new AGA or CSA approved
gas supply line.
Install a shut-off valve.
Securemy tighten alt gas
connections.
If connected to LP, have a
quamified person make sure gas
pressure does not exceed 14"
water column.
Examples of a qualified person
include licensed heating
personnel, authorized gas
company personnel, and
authorized service personnel.
Failure to do so can result in
death, exp{osion, or fire.
Observe all governing codes and
ordinances.
important: Cooktop must be connected to
a regulated gas supply.
regulat0r (
witil product) masfbe
installed with arrow up
pointing at sookfop
h0n0m
I/2"nipple
(notsupplied)
AGA orCSA approved
flexibJestainless
steamgassupplyline
(not supplied)
36" (91,4 am)
3=prongground=type
power supply sord
Typical Gas and Electric
Connections
Copies of the standards listed may be
obtained from:
* CSA hternationat
8501 East P_easant Valley Rd.
C_eveJand, Ohio 44t31-5875
installation must conform with
local codes and ordinances, in the
absence of local codes, installations must
conform with American National
Standard, National Fuel Gas Code
ANSI Z223.1 -- latest edition or
CANI -- B149.1 or 2".
Einput ratings shown on the
model/serial rating plate are for elevations
up to 2,000 feet (610 m). For elevations
above 2,000 feet (610 m), ratings are
reduced at a rate of 4% for each 1,000
feet (305 m) above sea level.
C mThe cooktop is equipped for use
with NATURAL gas. it is design=certified
by international Approval Services (I=A=S=)
for NATURAL and LR gases with
appropriate conversion. The model/serial
rating plate, located on the underside of
the burner box, has information on the
type of gas that can be used. if this
information does not agree with the type
of gas available, check with the local gas
supplier. 5

LP. Gas:
No attempt shall be made to convert the
cooktop from the gas specified on the
model/serial rating plate for use with a
different gas without consulting the
serving gas supplier. Conversion must be
done by a qualified service technician. To
convert to L.R gas, use L.R gas
conversion kit part no. 8284934. The parts
for this kit are in the literature package
supplied with cooktop.
mProvide a gas supply line of 3/4"
rigid pipe to the cooktop location. A
smaller size pipe on long runs may result
in insufficient gas supply. Pipe-joint
compounds, suitable for use with L.R gas,
must be used. With L.R gas, piping or
tubing size can be 1/2" minimum. L.R gas
suppliers usually determine the size and
materials used on the system.
E mIf local codes permit, use a flexible
stainless steel tubing gas connector,
design-certified by AGA or CSA
International, to connect the cooktop to
the rigid gas supply line. 5/8" diameter line
is recommended. Do Not kink or damage
the flexible connector when moving the
cooktop. The pressure regulator has 1/2"
female pipe threads. Youwill need to
determine the fittings required, depending
on the size of your gas supply line, flexible
metal connector and shutoff valve.
shu_uf,valveo_-__
"upen" pusitU
/_ gas supply
F line
EThe supply line shall be equipped
with an approved shutoff valve. This valve
should be located in the same room as
the cooktop and should be in a location
that allows ease of opening and closing.
Do Not block access to the shutoff valve.
The valve is for turning on or shutting off
gas to the appliance=
G ,If rigid pipe -__
is used as a gas 1r_
supply line, a combination of pipe _l
fittings must be used to obtain an in-line
connection to the cooktop. All strains
must be removed from the supply and
fuel lines so cooktop will be level and in
line.
raTheregulatormust be checked at a
minimum 1-inch(2.5 cm) water column
above the set pressure.The inlet pressure to
the regulator should be as follows for
operation and checking the regulatorsetting:
NATURAL GAS:
Set pressure 5 inches (12.7 cm) W.C.
Supply pressure 7-14 inches (17.8 cm
to 35.5 cm) W.C. maximum.
L.P. GAS:
Minimum pressure 10 inches
(25=4cm) W.C.
Supply pressure 14 inches
(35.5 cm) W.C.
ELine pressure testing:
Testing above 1/2 psi (3.5 kPa) or
14 inches (35.5 cm) W.C. (gauge)
The cooktop and its individual shutoff
valve must be disconnected from the gas
supply piping system during any pressure
testing of that system at test pressures
greater than 1/2 psig (3.5kPa).
Testing below 1/2 psi (3.5 kPa) or
14 inches (35.5 cm) W.Co(gauge) or
lower
The cooktop must be isolated from the
gas supply piping system by closing its
individual manual shutoff valve during any
pressure testing of the gas supply piping
system at test pressures equal to or less
than 1/2 psig (3.5 kPa).
Electrical Shock Hazard
Plug into a grounded 3-prong
outlet.
Do not remove ground prong.
Do not use an adapter.
Failure to follow these
instructions can result in death,
fire, or electrical shock.
If codes permit and a separate ground
wire is used, it is recommended that a
qualified electrician determine that the
ground path is adequate.
Check with a qualified electrician if you
are not sure whether the cooktop is
properly grounded.
Do not ground to a gas pipe.
A 120=volt,60=Hz, AC=only, 15=ampere,
fused electrical supply is required. A
time=delay fuse or circuit breaker is
recommended. It is recommended that a
separate circuit serving only this
appliance be provided.
Electronic ignition systems operate within
wide voltage limits, but proper ground and
polarity are necessary, in addition to
checking that the outlet provides 120=volt
power and is correctly grounded, the
outlet must be checked by a qualified
electrician to see if it is wired with correct
polarity. A wiring diagram is provided on
the last page of these instructions.
Important: This cooktop is equipped with
an electronic ignition system that will not
operate if plugged into an outlet that is
not properly polarized.
This appliance, when installed, must be
electrically grounded in accordance with
local codes or, in the absence of local
codes, with the current CSA standard
C22.1. Canadian Electrical Code Part 1".
Recommended ground method
For your personal safety, this cooktop
must be grounded. This cooktop is
equipped with a 3-prong ground plug. To
minimize possible shock hazard, the cord
must be plugged into a mating 3-prong
ground4ype outlet, grounded in
accordance with the National Electrical
Code ANSI/NFPA 70 latest edition** or
Canadian Electrical Code (CSA)* -- and
local codes and ordinances. If a mating
outlet is not available, it is the personal
responsibility and obligation of the
customer to have a properly polarized
and grounded, 3-prong outlet installed by
a qualified electrician.
3=prougpuJarized
ground=type outlet _
3=prong
ground plug
Copies of the standards listed above may be
obtained from:
*CSA mnternational
8501 East P_easant Valley Rd,
C_eveJand, Ohio 44131-5575
** National Fire Protection Association
One Batterymareh Park
Quincy', Massachusetts 02269

Installation
E Remove the top wood sheet from
over the top of the cooktop.
mRemove the shipping brackets and
discard.
Excessive Weight Hazard
Use two or more peop{e to move
and instatl cooktop.
Failure to do so can result in back
or other injury.
mCarefully lift the cooktop up and set
aside. Write down the model and serial
numbers before installing the cooktop.
Both numbers are on the model/serial
number plate located on left front
underside of the burner box.
E Unpack the burner grates, burner
caps, simmer plate, grille grate, drip tray,
spill guard, wave tray,wave plate, tile
bezels, regulator, backguard and island
trim. Items are either packaged under the
cooktop or on the cooktop. Parts shipped
with cooktop depend on model ordered.
mThe pressure regulator and flexible,
stainless steel gas supply line connector
can be assembled to the cooktop now or
after the cooktop is installed in the cutout.
To assemble now, stand the cooktop on its
side or back surface and complete this
part of the pressure regulator/gas line
connector assembly.
To connect the flexible, stainless steel
connector to the pressure regulator
requires a 1/2" nipple.
Install the pressure regulator with the
arrow pointing up toward the bottom of the
burner box and in a position where you
can reach the regulator cap.
IMPORTANT: All connections must be
wrench-tightened. Do not make
connections to the gas regulator too tight.
Making the connection too tight may crack
the regulator and cause a gas leak. Do not
allow the regulator to turn on the pipe
when tightening fittings.
Use only pipe-joint compound made for
use with Natural and L.R gas. Do not use
teflon tape. You will need to determine the
fittings required depending on your
installation.
®48" 121.9 cm) models wUtbbotb grille and
gr dd e do net use screw A
®36" (91.4 cm) roudels wffh griddle do nut use
screw B
®All utber models use all 3front screws
®3rear screws requUredbut Butshownon48"
(121.9 cm) modeUsand 2 rear screws required
but notshown on 36" (91.4 cm) models
attashing the
backguard
48" (121.9 cm) models with both grille and
griddle use screws at Dand E
All uther models use screwsat Cand E
c
6m Attach the backguard or island trim
as required for your installation. Attachment
screws are in the literature package.
7E Carefully lift and place the cooktop
into the front area of the cutout. Be
careful not to pinch the power supply cord
or damage the pressure regulator/flexible
gas supply line connector if installed. DO
NOT place all the way back into cutout.
m Place cooktop completely into
cutout. NOTE: The cooktop must be level
for best cooking performance.
9m tf the pressure regulator and
flexible, stainless steel gas supply
were not assembled in Step 3,
complete the assembly now, The
pressure regulator MUST be installed
with arrow on the regulator pointing up
toward the burner box.
0m Connect flexible, stainless steel
gas supply connector to the rigid gas
supply line. Do not kink the connector. You
will need to determine fittings required
depending on your installation.
shutuf{ valve --_ _
"open" pusitien r_ ,_,_f.,
gas supply. ,_I'I._ _'_
/_-_ to cooktup
mOpen shutoff valve in the gas
supply line. Wait a few minutes for gas to
move through the gas line.
E Leak testing of the appliance
shall be conducted according to the
following instructions:
Test all connections by brushing on an
approved non-corrosive leak-detection
solution. Bubbles will show a leak. Correct
any leak found.
gastube /
opening
m Put burner caps on each burner
base. Place burner grates over burner
bases and caps.
If your model has only surface burners
(no grille or griddle), go to "Check the
operation of the surface burners, grille
and griddle."
If your model was shipped with
a grille or griddle, go to "Installing the
grille or griddle" to complete the
installation.

JnstaJJJngthe 9riJJe
or griddJe.
Grille installation: Go to Step 15.
Griddle installation: The griddle is
factory installed. Tocomplete the
installation, go to Step 16.
mInstalling the gritle:
A, Liflthelog burnerup outofthe bay
and set aside.
locating feet
tray
B, Place drip tray on bottom of grille
bay and slide the tray forward so that it is
located side-to-side and against the
locating feet of the rear spill guard.
insert feet
into slots
C, Insert the front spill guard feet into
the slots in the rear spill guard as shown.
The rear flange will rest on the burner box.
8
D, Reinstall the log burner. Make sure
burner's rear flange is seated in slot.
E,, Plug power supply cord into
grounded outlet.
F, Check the surface burner and grille
flames. Before completing the grille
installation, go to "Check the operation of
the surface burners, grille and griddle."
slot for
g tab
_ocating
tab
/
G, Install the wave tray into the
grille/griddle bay. The tab in the left rear
corner of the bay must fit through the slot
in the left rear corner of the wave tray.
wave wave
J p_ate
H, Place the wave plate on the wave
tray as shown, The wave plate must be
centered on the wave tray,
_, Install the grille grate.
m Completing the griddle
installation:
griddle
drip tray
A, Place drip tray in the well at the
front of the griddle. Slide tray forward until
it stops.
B, Refer to the Use and Care Guide
that came with your Cooktop for
instructions on cleaning and seasoning
the griddle before using.
C, Plug power supply cord into
grounded %prong outlet,
D, Check the surface burner and
griddle flames. Go to "Check the
operation of the surface burners, grille
and griddle."

Check the
9rJiie and 9riddle,
E_ectronic Ignition System m
initia_ lighting
Surface burners use electronic ignitors
in place of standing pilots. When the
cooktop control knob is pushed in and
turned to the "LITE" position, the system
creates a spark to light the burner. This
sparking continues until the control knob
is turned to the desired setting.
The gdlle and gdddle burner use an
ignitor glow bar that is either on or off in
place of standing pilots. When the glow
bar is hot, it sends a signal back to the
safety valve which opens allowing gas to
flow.
eooktop grille griddle
burners knob knob
A. Push in and turn the surface
burners and grille control knobs to "LITE"
position. For griddles, turn the griddle
control knob to a temperature degree
mark (300° recommended). The surface
burner flame should light within 4
seconds and the grille and griddle flame
in 30-40 seconds. Note: the griddle flame
cannot be seen, but you should hear it
ignite and feel heat from the griddle.
After lighting the burners, turn the
control knobs "OFF",
If burners do not light properly, turn
control knob to the "OFF" position. Check
that burner cap is in the proper position.
Check that power supply cord is plugged
in and that circuit breaker or house fuse
has not blown. Check that the shutoff
valve is in the "ON" position. Check
operation again.
If a surface burner, grille or griddle does
not light at this point, contact your
KitchenAid dealer for assistance.
B. Adjusting the surface burner or
grille flame: NOTE: there is no
adjustment for the griddle flame. Gas flow
is at 100%, temperature is controlled by
thermostat.
Push in and turn each control knob to the
'%O" position. The '%O" setting of each
burner has been factory set to the lowest
position available to provide reliable
reignition of the burner. If it does not stay
lit on the '%0" position, check '%0"
position as follows:
a.Turn control knob to "LITE" until burner
ignites.
b. Quickly turn control knob down to "LO"
position.
c. if burner goes out, readjust valve as
follows:
Remove control knob. Insert a flat-blade
screwdriver into the hollow vane stem
and engage the slotted screw. Flame size
can be increased or decreased by turning
the screw. Adjust flame until you can
quickly turn control knob from "HI" to '%0"
position without extinguishing the flame.
Flame should be as small as possible
without going out.
ports
typical surfac,
burner flame at
highest setting
C. Check flame on "HI" for a blue
color. It should be clean and soft in
character. No yellow tip, blowing or lifting
of flame should occur. Occasional orange
flashes are normal and reflect different
elements in the air or gas.

Installer checkoff
COOKTOP
[_ Cooktop correctly positioned in
countertop cutout,
[_ Maintained specified distances to
cabinet surfaces.
[_ Cooktop level - front to back - side
to side.
[_ Burner caps positioned properly on
sealed burner bases.
[_] All packing material removed.
[_ Backguard or island trim attached
(see page 4).
[_ Depending on model, grille parts
correctly assembled.
[_ Depending on model, griddle parts
correctly assembled.
[_ Polarized and grounded 120-volt,
60-Hz, AC, 15-amp fused electrical
supply for power supply cord
connection.
GAS SUPPLY
[_ Connection: !/2" NPT with a
minimum 5/8" (15.9 mm) diameter
flex line.
[_The cooktop is connected only to
type of gas for which it is certified for
use.
If ceektep
net eperate:
[_ Check that the circuit breaker is not
tripped or the house fuse blown.
[_ Check that the power supply cord is
plugged into the outlet.
[_ Check that gas valves are turned to
the "ON" position.
[_See Use and Care Guide for
troubleshooting list.
If youneed
The KitchenAid Consumer Assistance Center
will answer any questions about operating or
maintaining your cooktop not covered in the
Installation Instructions. The KitchenAid
Consumer Assistance Center is open 24
hours a day, 7 days a week. Just dial 1o800-
422o1230 -- the call is free within the
continental United States, or visit our web site
at www.kitchenaid,com.
When you call, you will need the cooktop
model number and serial number. Both
numbers can be found on the model/serial
rating plate located on the bottom of the
cooktop and are visible through the cutout in
the left-hand back corner of the enclosure
bottom.
In the event that your KitchenAid
appliance should need service, call the
dealer from whom you purchased the
appliance or a KitchenAid-designated
service company. A KitchenAid-
designated service company is listed in
theYellow Pages of your telephone
directory under "Appliances --
Household -- Major -- Service and
Repair."
You can also obtain the service
company's name and number by dialing,
free within the continental United States,
the KitchenAid Consumer Assistance
Center telephone number, 1-800-422-
1230.A special operator will tell you the
name of your nearest KitchenAid-
designated service company.
Maintain the quality built into your
KitchenAid appliance -- call a
KitchenAid-designated service company.
If removing the cooktop is necessary for
maintenance, shut off gas supply.
Disconnect the gas and electric supply.
After disconnecting the gas and electric
supply, finish removing the cooktop.
Generally, the cooktop does not need to
be removed for servicing.
10

S6" (91,4) cooktopmodels
THE POWER CORD ON THIS APPLIANCE IS EQUIPPED WITH A 3-PRONG GROUND PLUG
WHICH MATES WITH STANDARD 3-PRONG GROUND-TYPE OUTLET.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS
WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION
VERIFY PROPER OPERATION AFTER SERVICING.
6 su_ace burners
LINE PLUG
1/4 WIDE 5/16 WIDE
BLADE BLADE
ROUNDBLADE
GRN OR GRN/Y Ij'
B GROUND
]
BK RIB
CONNECT SPARK
250 TERMINALS MODULE
120VAC60Hz
1 PHASE
15OR20AMP
BK ISLcO2BRN
SURFACESWITCHESVALVEBURNER 1--
±±t [zz
SURFACE BURNER
IGNITOR ELECTRODES
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB IS ROTATED
55 TO 95 COUNTER CLOCKWISE FROM OFF
4surface burners with griddle
_LU(
120 VAC 60 Hz GRIDDLE
1 PHASE VALVE
_KRIB GROUND 15 OR 20 AMP _
GRN OR GRN/Y t [I
BK c*
W
IGNITOR
4surface burners with grille
120 VAC 60 Hz
1 PHASE
15 OR 20 AMP
BK 3K RIB
GRN OR GRN/Y tie GROUND
BK
BK J" W
BK BK -_-
SURFACE BURNER
VALVE
SWITCHES
_w GRILLE
VALVE
SWITCH
_'_ SPARK
MODULE
$ $
SURFACE BURNER
IGNITOR ELECTRODES
GRILLE
_GN_TOR
GRILLE
VALVE
w
SWITCHES ON SURFACE BURNER
VALVES:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 55 TO 95
COUNTER CLOCKWISE FROM OFF
SWITCH ON GRILLE VALVE:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 20 TO 360
COUNTER CLOCKWISE FROM OFF
THERMOSTAT IGNITOR ELECTRODES
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB IS ROTATED
55' TO 95' COUNTER CLOCKWISE FROM OFF
11

48 mm
{121.9 cm}cooktopmodels
THE POWER CORD ON THIS APPLIANCE IS EQUIPPED WITH A 3-PRONG GROUND PLUG
WHICH MATES WITH STANDARD 3-PRONG GROUND-TYPE OUTLET.
CAUTION: LABEL ALL WIRES PRIOR TO DISCONNECTION WHEN SERVICING CONTROLS.
WIRING ERRORS CAN CAUSE IMPROPER AND DANGEROUS OPERATION
VERIFY PROPER OPERATION AFTER SERVICING
8 surface burners 6 surface burners with grille
PLUG
SURFACE BURNER
IGNITOR ELECTRODES
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB IS ROTATED
55 °TO 95 COUNTER CLOCKWISE FROM OFF
6 surface burners with griddle
BK RIB
GRN OR GRN/Y
BK
SURFACE BURNER
VALVE SWITCHES
GRILLE
VALVE SWITCH
120 VAC 60 Hz GRILLE
1 PHASE VALVE
15 OR 20AMP
tI'GROUNDBK
w w
SPARK
MODULE GRILLE
IGN_TOR
ii
$ $ $ $$$ 6ELOB
SURFACE BURNER
IGNITOR ELECTRODES
SWITCHES ON SURFACE
BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 55 TO 95°
COUNTER CLOCKWISE FROM OFF
SWITCH ON GRILLE VALVE:
ELECTRIC CIRCUIT CLOSED WHEN
KNOB IS ROTATED 26° TO 360
COUNTER CLOCKWISE FROM OFF
4 surface burners with grille and griddle
3K RIB
GRN OR GRNf_{
BK
BK BK
SURFACE BURNER
VALVE SWITCHES
GRIDDLE
120 VAC 66 Hz VALVE
1 PHASE
tl'GROUNDBK16OR20AMP
w w
THERMOSTAT 2_2_
SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB
IS ROTATED 55 TO 95 COUNTER
CLOCKWISE FROM OFF
GRIDDLE
IGNITOR
l*_ YEL OR BRN
2_ ± 2_ 2_ 6ELOS
SURFACE BURNER
iGNITOR
ELECTRODES SWITCHES ON SURFACE BURNER VALVES:
ELECTRIC CIRCUIT CLOSED WHEN KNOB
IS ROTATED 55' TO 95' COUNTER
CLOCKWISE FROM OFF
Part No. 8285479
© 2003 KitchenAid.
® Registered Trademark/Trademark of
KitchenAid U.S.A., KitchenAid
Canada licensee in Canada
Kitchen_kid ®
HOME APPLIANCES
Prepared by KitchenAid, Benton Harbor, Michigan 49022 Printed in U.S.A.

e®
Kitchen kid
BIEN PENSE, BJEN FABRIQ_UE_' Pour toute question concernant caracteristiques, utilisation, performance,
piece ou service, tel6phoner au
1o800o422ol230 ou consulter notre site
Internet & I'adresse www.kitchenaid.com
IMPORTANT :
lnstallateut" : Remettre les instructions
d'installation au proprietaire.
Propd_taire : Conserver les instructions
d'installation pour consultation ulterieure.
Conserver les instructions d'installation
pour consultation par I'inspecteur local
des installations electriques.
inscdre ci-dessous les numeros de
modele et de serie avant d'installer la
table de cuisson.
On trouve cette information sur la plaque
signaletique, sur la surface interne du
coffret des brOleurs.
N° de modele
N° de serie N° de piece 8285479

Avant de commencer...
Votre s@curit@et celle des autres
est tr@simportanteo
Nous donnons de nombreux
messages de securit6 importants dans
ce manuel et sur votre appareii
menager. Assurez-vous de toujours
lire tousles messages de securit6 et
de vous y conformer.
Voici le symbole d'alerte de
securit&
Ce symbole d'alerte de
securit6 vous signaJe les dangers
potentiels de deces et de blessures
graves & vous et a d'autres.
Tous les messages de securit6
suivront le symbole d'alerte de
securit6 et le mot "DANGER" ou
"AVERTISSEMENT". Ces mots
signifient :
Risque possible de d_c_s ou de
btessure grave si vous ne suivez pas
imm_diatement Jes instructions,
Risque possible de d_c_s ou de
blessure grave si vous ne suivez
pas les instructions,
Tousles messages de securit6 vous
diront quel est le danger potentiel et
vous disent comment reduire le risque
de blessure et ce qui peut se produire
en cas de non-respect des instructions.
Important : Observer les dispositions de
tous les codes et reglements en vigueur.
AVERTJSSEMENT : Si les
instructions clans ce
manuel ne SORt pas
suivies, un incendie ou une
expmosion peut causer des
dommages aux biens, une
blessure ou un d_c_s.
m Ne pas remiser ou utiliser
d'essence ou un autre
produit liquide ou gazeux
inflammable _ proximit_
de cet apparei_ ou de tout
autre appareil
_lectrorn_nager.
QUE FAmRE Sl UNE
ODEUR DE GAZ EST
oNe pas essayer de
mettre un apparei_ en
rnarche.
oNe toucher aucun
commutateur _ectrique.
oN'utiliser aucun
t_l_phone de I'_difice.
o Contacter
imrn_diatement _e
fournisseur de gaz
depuis le t_l_phone d'un
voisin. Ex_cuter les
instructions du
fournisseur.
oSi le fournisseur de gaz
n'est pas accessible,
appeler les pompiers.
L'instaHation et _es
travaux de service doivent
_tre effectu_s par un
_lectricien qualifi6, par
une agence de service ou
par le fournisseur de gaz.
Remarque : Cette table de cuisson est
conue pour I'alimentation au gaz naturel.
Pour la conversion au gaz propane, voir
les instructions de conversion present6es
dans les documents qui accompagnent le
produit.
Un raccord de connexion a la canalisation
d'arrivee de gaz doit _tre disponible. Voir
"Specifications de I'alimentation en gaz."
La responsabilite de la qualite de
I'installation incombe au proprietaire.
Demander a un technicien qualifie
d'executer I'installation.
V@ifierque tout le mat@ielnecessaire pour
une installation correcte est disponible.
C'est a I'installateur qu'incombe la
responsabilite de respecter les
degagements de separation specifi6s sur la
plaque signaietique. On trouve la plaque
signaletique sur la face inf@ieuredu coffret
des brOleurs.
On recommande qu'une hotte d'extraction
soit installee au-dessus de la table de
cuisson. Pour I'installation sur un '_lot,on
recommande une hotte de 122 cm (48 pc).
Inspecter I'emplacement oQ la table de
cuisson sera installee. Eemplacement
d'installation devrait _tre situe a distance
de toute source de courants d'air
intenses, comme fen6tres, porte, bouche
de chauffage ou ventilateur.
Ne pas entraver la circulation d'air de
combustion et d'air de ventilation.
Toutes les ouvertures decoupees dans le
mur ou dans le plancher au voisinage de
I'endroit oQ la table de cuisson sera
installee doivent _tre scellees.
Une Haison _lectrique _ _aterre est
necessaire. Voir "Specifications de
Hnstallation electrique."
C'est au client qu'incombe la
responsabilit_ :
de contacter un 6iectricien quaiifi_
pour l'instaltation.
de s'assurer que l'instaltation
_tectrique est adequate et conforme
aux dispositions du Code national des
installations _lectriques ANSI/FNPA 70
-demi_re _dition*, ou du Code
canadien de l'_lectricJt_ O22.1-1982 et
C22,2 n°01982 (ou derni_re _dition}**,
et aux dispositions des codes et
r_glements Iocaux.
On peutse procurerdes exemplairesdes normes
indiqu6esaux adressessuivantes:
* Nationa} Fire Protection Association
One Batterymareh Park
Quincy, Massachusetts 02288
** CSA InternationaJ
8801 Bast P_easantValley Rd.
Cleveland, Ohio 44131-8878

imensions du ui
cordon
d'alimentatUoe de
91,4 cm (36 pc)
avac fiche de
braechemeet _ 3
braehas (liaUsen
la terra) 91,1 cm (35 7/8table de ca[scan de 91,4 cm {36 pu) : pu)/
table de caUssonde 121,9 cm (48 pc) : 121,_o) //
deaseret (representS)
ea bien garniture pour Uostallatien
aer i'lat (veff p_4 et 7) Pourlea mode[as de
121,9 cm (48 po) _ 8
br_leura aeUqaament:
15,2 cm (6 pe)
Teas lea autrea modules :
(gpc)
/
66,7 cm (264/4 pa)
66,7 cm (26ol/4 pc)
22,2 mm _
(7/8po} [
55,8 mm ====._=,_- _e==_ 55,g cm (22
(24/18 pa) pa)
I
F_
t Pour lea £d_les de
121,9 cm (48 pa) _ 8
brQlears uniquemeet :
9,Smm 15,2cm 8pc)
(3/8" po) Teas [es autres med_las :
(9pc)
18,1 cm
(74/8pc)
{
entree de la canalisation de gaz &4,8 cm
= -- (1 7/8 pa) de ['artiSte da coffret des
br_leara et _ 12,4 cm (4 7/8 pc) depais le
c6t_ gauche da coffret des br_lears.
38,2 mm
(1 3/18 po)
table de caisson(we [at_rale)

imensions o
Respecter les dimensions indiqu_es
pour i'ouverture _ d_couper et les
distances de s_paration. Les dimensions
indiquees tiennent compte des
degagements de securit6 necessaires.
Installation dans une r_sidence mobile :
I 'installation de cette table de cuisson doit
satisfaire les criteres de la norme
Manufactured Home Construction and
Safety Standards, titre 24 CFR, partie 8280
(anciennement norme fed6rale pour
construction et securit6 des residences
Au Canada, I'installation de cette table de depose de la table de cuisson.
cuisson doit satisfaire Ins criteres de la Prevoir une ouverture decoupSe darts
norms CAN/CSAoZ240 (derniere edition)** I'angle arriere gauche de la cavite
ou des codes Iocaux en vigueur, d'encastrement pour le passage de
La table de cuisson est congue pour qu'elle I'arrivee de gazet du cordon d'alimentation
suit soutenue sur le plan de travail par les electrique, et pour qua la plaque
rebords des c6tes et de I'arriere. signaletique suit visible.
Les arrivees de gazet d'electricit6 Onpeutseprocurerdes exemptaires des hermes
devraient _tre placees seJonIns indications indiquSesauxadressessuivantes:
de Mllustration"Dimensions oarrivees de * National Fire Protection Association
gaz et d'electricitS", pour que I'acces & ces OneBatterymarchPark
points de connexion suit possible darts Quincy,Massachusetts 02269
mobiles, titre 24 HUD partJe280); ou si **CSAinternational
cette norms n'est pas applicable, L._ 8601 East Pleasant VamJeyRd.
. ......... ['_"_-_ C_evetand, Ohio 44131-6676
I ins[alia[ton oo11: sacisralre les prescnpuons j -_
de la norme d'installation des residences _ C_ .
prefabriquSes (Manufactured Home Sites, I _ --_'_-_
Communities and Setups) ANSI A225.1 o J J'l -_'_---_ J
derniere edition* ou Ins prescriptions des J /_ _ .....
33sm
distance mhl. de I _
..... 45,7 sm 118pe_ I J
['encpsne am[ _entre placard et [_'_<-".............. L J
etre egale des /plan
neexs_es. --- I ....... C B mie.
1a,4cm 1,gsm13/4Pal
(71/4po) _,/
vair d_tails 56,5 sm
de Faegle (22=1/4 pu)
/----- 16,1cm(6718pc)
ENCOCHEDANS
UANGLE- DETAIL 12,1 cm
(4 3/4 pa) distance de
s_paration dn tour
lateral, rain. 31,3 sm
/5,1 sm (12 5116po) de
cheque cSt_ (24 po)
[} placard
inf_riaer
faille
91,4cm(36pa)
121,9 sm
(48pal
med_le
KGCP462K
KGOP463K
KGCP467J
KGOP482K
KGOP483K
KGOP484K
KGCP487J
A
garniture de Hlot
12,7 sm
(5pa)
15,2 Sm
(6pu}
12,7 nm
15pa}
15,2 cm 16po}
12,7 sm
15pa}
dasseret
4,4 nm
(1 3/4 pc)
4,4 Sm
113/4pc)
7,6 sm
{3 paI
B(_in.)
garnituredeFlint dosseret
121,gcm(48Psi
121,gsm(48po)
sudase noncombustible
121,9 sm 121,9 sm
(46pal 148pal
nan combustible
121,9 sm
148psi
121,9sm (48po)
noncombustible
6
ouverture
pourdesseret
91,4 sm
p6 pal
121,9 sm
(46po)
D
placard et
plan de travail
89,5 Sm
(35 1/4po)
128,8cm
(471/4pu)
plan de travail seulement
91,4 sm (36 pe) au
91,1 sm (35 7/8 pa)
avec d_gagement nul
121,9 sm (48 pc) ou
121,6 sm (47 7/8 pn)
even d_gagement nul
£emarque : #,mains d'avis sontraire, ins dimensions suet callas de la distance de s@aratian entre use surface combustible.

en .qaz
Remarque : Cnt_
plehl et teed de la
savit_ d'ensastremeat
pax repr_seet_s.
Raccordement aux canalisations
de gaz et de _'6_ectricit6
d_4eedeur (teurei ave¢
le produit) - lore de
Hestallatioe, erieeter
Io tt_ebe vers le
vers le fond de la tone
de ceisson
raseerd 1/2 pe
(postoorei) _
seedeit de raeserdement
flexible, d'asier ieoxydabie
_pas foorei) - hemelegatien
A eo CSA
serdee d'alimentatiee
(36 po) ayes
fiche de bransbemeet
3bresbes (Haisen _ la
terre)
rebieet d'arrbt
(pas {eurni)
\sanalisatien d'arriv_e
de gaz - pressien
r_gol_e
avaet de la table
de suissen
Raccordements typiques aux circuits
de gaz et de ['6[ectricit_
On peut se procurer des exemptaires des
normes indiqudes _ I'adresse suivante •
* CSA (ntemationat
8501 East Pleasant Valley Rd.
C_eveland, Ohio 44131°5575
Risque d'ex})losion
UtiHser un conduit de raccordement
la canaHsation de gaz a})})rouv6
par AGA ou CSA,
Installer un robinet d'arrCt.
Bien serrer toes Jes joints des
raccords du circuit de gaz.
Si I'a})})areil est reli6 _ une
canaHsation de gaz })to}jane,
demander _ une })ersonne quaHfide
de v_rifier que la })ression de gaz ne
d_})asse })as 14 })o (cotonne d'eau),
(Personnes qualifi_es = })ersonnet
com})dtent d'un foumisseur
d'6quipement de chauffage, d'une
com})agnie de distribution de gaz, ou
d'une entre})rise d'entretien agr_e).
Le non=res})ect de ces instructions
})eut causer un d@cds, une ex})losion
ou un incendieo
Observer tes dispositions de tousles codes et
regtements en vigueur.
Important : La table de cuisson doit 6tre
connectee a une source de gaza pression
regulee.
realisee selon ces instructions
doit _tre conforme aux dispositions des codes et
reglements Iocaux. En I'absence dun code local,
I'instattation doit _tre conforme aux dispositions de
la norme American National Standard, Nationat
Feet Gas Code ANSI Z223.1 oderniere edition*
ou de la norme CAN!oB149.1 ou 2*.
La capacite thermique indiquee sur la
plaque signatetique correspond a une altitude
inferieure & 610 m (2000 pi). Pour une altitude
superieure &610 m (2000 pi), reduire la capacite
thermique & raison de 4 % pour chaque tranche de
305 m (1000 pi) au-dessus du niveau de la met.
C_ Cette table de cuisson est equipee pour
I'aIimentation au gaz NATUREL Sa conception est
homologuee par International Approval Services
(I.A.S.) pour ralimentation au gaz NATUREL ou au
propane (avec conversion appropriee). La plaque
signaletique, situee sur ta face inferieure du coffret
des brOleurs, mentionne le type de combustible
utilisable. Si cette information ne concorde pas
avec te type de gaz disponibIe, consulter te
fournisseur de gaz tocal. 5

Propane :
Ne jamais tenter, sans avoir d'abord consulte le
fournisseur de gaz, de modifier la table de
cuisson pour I'alimentation avec un autre gaz
que celui specifi6 sur ta plaque signaletique.
Toute conversion doit 6tre execut6e par un
technicien qualifi& Pour la conversion au
propane, utiliser I'ensemble de conversion n°
8284934. Ces pieces accompagnent les
documents fournis avec Ja table de cuisson.
Installer une canalisation de gaz rigide de
1,9 cm (3/4 po) jusqu'a I'emplacement de la table
de cuisson. L'emptoi d'une canatisation de
diametre inf@ieur sur une grande distance peut
rendre le debit de gaz insuffisant. Utiliser un
compose d'etanch6it6 des jointures con_u pour
I'utilisation en p@sence de propane. Pour
I'alimentation au propane, utiliser une canalisation
de diametre d'au moins 1/2 po. Habitueltement, le
fournisseur de propane determine la tailte des
canatisations a utiliser avec te systeme.
E mSites codes ou les regtements Iocaux le
permettent, on recommande I'emploi d'un conduit
de raccordement metatlique flexible (homologation
American Gas Association ou CSA international,
pour le raccordement de la table de cuisson a Ja
canaiisation de gaz. On recommande une
canatisation de diametre 5/8 po. Veiller a ne pas
deformer ou endommager le conduit flexible lots
des d@tacements de la table de cuisson. Le
detendeur comporte un filetage femelle de 1/2 po.
On devra determiner quels raccords sont
necessaires, scion la taille de Jacanalisation de
gaz et les caract@istiques du robinet d'arr6t et du
conduit de raccordement metallique flexible.
rebi_et d'arr_t
canalisati0n "Ùuvert".
d"arriv@
vers la table
F de _uisson
ELa canalisation d'arrivee de gaz devra
comporter un robinet d'arr6t homologu& Ce
robinet d'arr6t devra 6tre situe dans la m6me
piece que la table de cuisson, a un emplacement
permettant un acces aise pour les manoeuvres
d'ouverture et de fermeture. Ne pas entraver
J'acces au robinet d'arr6t; celui=ci est utilise pour
ouvrir et interrompre Fatimentation en gaz de
J'appareil.
G m Si ta canalisation _ dorac ,cs
de tuyauterie pour reatiser un raccordement
darts Faiignement de la table de cuisson. Toute
tension mecanique doit 6tre elimin6e de ta
canalisation de gaz, de mani@e que la table de
cuisson demeure horizontale et atignee.
mContr61er le fonctionnement du
detendeur a une pression d'au moins 2,5 cm (1
po) (colonne d'eau) au=dessus de la pression
nominate. La pression a I'entree du detendeur en
service devrait 6tre comme suit :
GAZ NATUREL :
Pression de reglage de 12,7 cm (5 po)
(colonne d'eau)
Pression d'alimentation maximale de
17,8 _ 35,5 cm (de 7 a 14 po)
GAZ PROPANE :
Pression minimale de 25,4 cm (10 po)
(colonne d'eau)
Pression d'alimentation maximale de
35,5 cm (14 po)
mTest de la canalisation d'arriv_e :
Test sous pression relative sup_rieure
3,5 kPa (112 Ib/po 2)ou 35,5 ere (14 po}
(ooJonne d'eau)
La table de cuisson et le robinet d'arr6t individuet
doivent 6tre deconnectes de la canalisation de
gaz au cours des tests du circuit d'alimentation &
une pression relative sup@ieure a 3,5 kPa
(1/2 Ib/po _)
Test sous pressJon relative de 3,5 kPa
(1!2 Iblpo _) -35,5 om (14 po) (eolonne d'eau) -
OU moins
La table de cuisson doit _tre isolee de la
canatisation de gaz par fermeture du robinet
d'arr6t individuel au cours des tests du circuit
d'alimentation sous une pression egale ou
inf@ieure a 3,5 kPa (1/2 Ib/po_).
$p@ifieations de
l'instatlatie
Risque de choc _ectrique
Brancher I'appareiJ dans une prise
de courant _ trois atv_oles reH_e
_aterre,
Ne pas enJever [a broche de liaison
& la terreo
Ne pas utiliser un adaptateur,
Le non=respect de ces instructions
peut causer un d_c_s, un incendie
ou choc _Jectriqueo
Si, Iorsque les codes le permettent, un
conducteur distinct de liaison a ta terre est
utilis& il est recommande qu'un electricien
quaJifie v@ifie Ja qualite de la Jiaison a la terre.
Consulter un etectricien qualifie en cas de doute
au sujet de Ja liaison a ta terre de Ja table de
ouisson.
Ne jamais utiliser une canaiisation de gaz pour Ja
liaison electrique a Ja terre.
L'appareil doit _tre atimente par un circuit
etectrique de 120 V (CA seutement), 60 Hz, 15
ou 20 A, protege par un fusible. On recommande
I'emploi d'un fusibie temporise ou d'un
disjoncteur. On recommande que cet appareit
soit alimente par un circuit ind@endant,
n'atimentant que cet appareit.
Le systeme d'ailumage etectronique fonctionne
clans une fourchette de tensions assez large,
mais il faut que I'appareiJ soit convenablement
relic & la terre et que la polarite soit respectee.
V@ifier que ta prise de courant etectrique est
correctement reliee a la terre et fournit une
tension de 120 V. Demander egalement & un
etectricien quatifie de v@ifier que la polarite de la
prise de courant est correcte. Un schema de
c_blage est presente & Is derni@e page de cette
brochure d'instructions.
Important : Cette table de cuisson est dotee
d'un systeme d'atiumage electronique qui ne
fonctionnera pas si erie est branchee sur une
prise de courant incorrectement polarisee.
Lorsqu'it est installe, cet appareit doit _tre
electriquement relic _ la terre conformement aux
dispositions des codes Iocaux ou, en Fabsence
de codes locaux, conformement aux dispositions
do la norme courante CSA C22.1 (Code
canadien de J'etectricit& l@e partie).
M@thode recommand_e de
liaison _ la terre
Pour la securite des utilisateurs, cet appareit doit
8tre relic a la terre. Cet appareit est equipe d'un
cordon d'alimentation dote d'une fiche de
branchement a 3 broches, pour Jiaison _ la terre.
Pour minimiser te risque de choc electrique, Je
cordon doit _tre branche sur une prise de
courant mutate correspondante, a 3 atveotes,
reliee a la terre, conformement aux dispositions
de I'edition la plus recente** du Code nationat de
I'electricite ANSI/NFPA 70 ou du Code canadien
de I'electricite (CSA)*, et des codes et
regtements tocaux en vigueur. Si une prise de
courant compatible avec la fiche n'est pas
disponible, c'est au proprietaire de l'appareit
qu'incombent la responsabilite et t'obtigation
personneltes de faire installer par un etectricien
qualifie une prise de courant a 3 alveoles
correctement reliee a la terre.
prise de couraat _ 3alv_oles,
reli_e _ la terre
61ectrique
On peut se procurer des exemptaires des
normes indiqu_es aux adresses suivantes :
*CSA Internationa_
8501 East P_easant Valley Rd.
C_eveland, Ohio 44131-5575
** National Fire Protection Association
One Batterymarch Park
Quincy', Massachusetts 02289

EOterlafeuiltedeboisrecouvrantlatable
decuisson.
mOterlescorni@esd'expeditionettes
mettreaurebut.
Risque de poids excessJf
UtiHser deux ou p[usde personnes
pour d6placer et installer la cuisni6reo
Le non-respect de cette instruction
peat causer une blessure au dos ou
d'autres blessures°
E Soulever prudemment la table de cuisson
et la mettre de c6te. Inscrire les num6ms de
modete et de s6rie avant d'instalter la table de
cuisson. Les deux num6ros se trouvent sur la
plaque signaletique se trouvant sur la face
inf@ieure avant gauche du coffret des brOleurs.
m Deballer les accessoires = grilles de
brOleur, chapeaux de brOteur, plaque de
mijotage, grille du grit, plateau ramasse-gouttes,
protecteur antiodeversement, plateau nervure,
plaque nervur6e, encadrements a carreaux,
detendeur, dosseret et garniture (pour [lot). Lea
accessoires se trouvent sous ou sur ta table de
cuisson. Les pieces exp6di6es avec la table de
cuisson d@endent du modete commande.
5E It est possible de connecter le detendeur
et le conduit de raccordement flexible d'acier
inoxydable des maintenant ou apres I'installation
de la table de cuisson dans ta cavite
d'encastrement. Pour effectuer immediatement ce
raccordement, placer la table de cuisson en appui
sur Jec6te ou J'arri6re, et connecter le detendeur.
Un raccord de 1/2 po est n6cessaire pour Ja
connexion entre le conduit flexible d'acier
inoxydable et le detendeur.
Lors de I'installation du detendeur, orienter la
fleche vers te haut, vers le fond du coffret des
brOleurs, et orienter te detendeur de telle mani@e
qu'il soit possible d'atteindre facilement le bouton
de r6gtage.
IMPORTANT : Serrer chaque connexion avec une
cle, mais ne pas serrer excessivement le raccord
dans te detendeur; ceci pourrait provoquer une
fissuration du detendeur, suscitant une fuite. Lors
du serrage des raccords, veilter ace que le
detendeur ne pivote pas par rapport au tuyau.
Utiliser uniquement un compose d'6tanch6it6
pour jointures compatible avec le gaz naturel et
te propane. Ne pas utitiser du ruban de teflon. II
sera n6cessaire de d6terminer quets raccords
utiliser, scion Ja configuration d'instatlation.
installation da
dosseret
2vis
m Fixer te dosseret ou la garniture pour Tlot,
selon la configuration d'instatlation. Les vis de
fixation se trouvent dans te sachet de
documentation.
7m Soutever prudemment la table de cuisson
pour Ja placer dans la partie avant de la cavit@
d'encastrement. Veiller a ne pas coincer le
cordon d'atimentation eta ne pas endommager
te detendeur et le conduit de raccordement
flexible. NE PAS pousser la table de cuisson
completement vers te fond de ta cavit@
d'encastrement.
m tntroduire comptetement la table de
cuisson dans la cavite d'encastrement.
Remarque : Pour qu'elle produise la meilleure
performance de cuisson, iJfaut que Ja table de
cuisson soit d'aplomb.
g m Si le detendeur et te conduit de
raccordement flexible d'acier inoxydable n'ont
pas et6 instalt6s a F6tape 3, effectuer maintenant
cette installation. Veiller a orienter la fleche du
detendeur vers Je haut, vers te coffret des
br01eurs.
Connecter le conduit de
raccordement flexible d'acier inoxydabte sur la
canalisation d'arrivee de gaz rigide. Ne pas
deformer le conduit de raccordement flexible. II
sera necessaire de d6terminer quels raccords
utiliser, selon la configuration d'instaltation.
rabinetd"arr_t =
sanalisatia, auvert -_._1----
d"ardv@ de _,_
_- _ _ ve_s latable
de saisson
E Ouvrir le robinet d'arr6t de ta
canalisation de gaz. Attendre pendant quelques
minutes que Jegaz remplisse Ja canalisation.
m Executer un test de recherche des
fuites conformement aux instructions ci-dessous.
Effectuer une inspection de recherche des fuites
sur chaque connexion; utiliser une solution non
corrosive approuv6e a cette fin. La formation de
bulles identifie une fuite. Effectuer les corrections
nScessaires pour 61iminer toute fuite observee.
E Placer te chapeau de brOleur sur
chaque base de brQteur. Placer la griJle de
brOleur sur chaque brOleur.
Si votre modete n'est muni que de brOJeurs de
surface (pas de gril ni de plaque a frire), passer
"V6rification du fonctionnement des brOleurs de
surface, du gril et de la plaque a frire.".
Si votre mod6te a 6te expedi6 avec
un gril ou une plaque a frire, passer &
"tnstaJlation du gril ou de la plaque a fdre" pour
achever I'installation.

Installation du grii oude
ta pJaque ffire
InstaJlation du grH: Passer a J'etape 15.
Installation de la plaque _ trite : La plaque
trite est installee _ J'usine. Pour achever
I'installation, passer & I'etape 16.
A, Soulever le brGleur hors de la cavite et le
mettre de c6t&
platen#
ramasse-
goottes
B, Placer le protecteur anti-deversement au
fond de la cavite du grit et glisser le plateau vers
I'avant de telle sorte qu'il se trouve en position
transversate contre les pieds repere du
protecteur antiodeversement arriere.
pieds et
fentes
C, Inserer les pieds du protecteur anti°
deversement avant darts tes fentes du protecteur
anti°deversement arriere. Le rebord arriere
reposera sur le coffret des brOleurs.
8
D, Reinstalter le brQleur. S'assurer que le
rebord arriere des brQleurs repose dans ta fente.
E, Brancher le cordon d'alimentation sur une
prise de courant reliee a Ja terre.
F, Verifier les flammes des brOleurs de
surface et du gril. Avant d'achever I'instaJlation du
gril, passer a "Verification du fonctionnement des
brOleurs de surface, du gril et de ta plaque
frire."
G, Installer te plateau nervure dans la cavite
du gril ou de ta plaque & frire. L'onglet dans te
coin arriere gauche de ta cavite doit passer
travers ta fente darts le coin arriere gauche du
plateau nervur& plaque
plateau j nervur_e
nnrvure
\
N, Placer ta plaque nervuree sur le plateau
nervure tel qu'iliustr& La plaque nervuree doit
6tre centree sur te plateau nervur&
_, Installer ta grille du gril.
6E Achevement de I'installation
de la plaque _ trite :
plateau ramasse-gouttes
de In plaque _ trire
A, Placer le plateau ramasse-gouttes darts
le puits a Vavant de la plaque a trite. Glisser le
ptateau vers I'avant jusqu'a I'arrSt.
B, Consulter te Guide d'utilisation et
d'entretien livre avec la table de cuisson pour
des instructions sur le nettoyage et le
conditionnement de ta plaque a trite avant son
utitisation.
C, Brancher le cordon d'atimentation sur one
prise de courant reliee a Ja terre.
D, Verifier tes flammes des brQleurs de
surface et du gril. Passer & "Verification du
fonctionnement des brOleurs de surface, du gril
et de la plaque a trite."